Search Documents

By W. L. Cooley, K. Y. Lee, M. M. Hassan

Because power system topographies for surface coal mines are significantly different from those for underground coal mines, the requirements for ground wire monitors for surface systems are somewhat different. This paper analyzes the problems faced by high-voltage ground wire monitors. Based on this analysis, some design requirements for monitors are suggested. Finally, results from laboratory evaluation of some of the commercially available monitors are presented.

Jan 1, 1979

By William O. Vanderburg

This paper describing the methods and costs of milling scheelite ore at the Silver Dike concentrator of the Nevada-Massachusetts Co., Inc., is one of a series being prepared by the Bureau of Mines. In the Silver Dike mill tungsten ore which contains about 1 per cent of scheelite is treated at the maximum rate of 45 tens per 24 hours by tabling followed by magnetic separators to clean the table concentrates. Unusually high-grade concentrates are produced which average between 70 and 75 per cent of W03.

Jan 1, 1932

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. [Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.]

By W. S. Landers

Analysis of the size consist of broken coal has been extended in recent years beyond the mere representation of the relative quantities of the various sizes present in a given lot of the material. Fundamental characteristics of the coal related to the process of breakage fix the distribution of sizes, and it has been found by Rosin and Rammler4/ that a relatively simple law-governs this property. Benhett5/ has described a graphical method of expressing the relationship, and by its use considerable simplification in the expression of size distribution is possible.

Jan 1, 1946

By James V. Luxner

The airflow and methane distribution patterns developed in an equipment-free entry 6.5 feet high and 12 feet wide, ventilated by line brattice operated blowing to or exhausting from the face, were determined by the Bureau of Mines for varying conditions. Results of these studies show that blowing line brattice systems of face ventilation are more effective than comparable exhaust systems. The face ventilating efficiency of any line brattice system is dependent upon the method of ventilation, the face distance, the tight rib distance, the volume of air delivered to the end of the line brattice, and the volume of methane released at the face. Experimental results indicate that maximum face ventilation efficiency is achieved when the inby terminus of the line brattice is installed 5 feet from the face and at a distance less than one-third the entry width from the nearest rib. Analyses of data are based upon the ability of a face ventilation system to dilute methane in the immediate face area.

Jan 1, 1969

By D. W. Butner

This report is concerned with the conditions affecting the methods and costs of mining phosphate rock in that part of the western phosphate field that is in Bear Lake and Caribou Counties in southeastern Idaho ( see fig . 1) . The area was selected because it contains most of the known phosphate reserve and because its geology has been studied more extensively than that of other sections . Deposits of phosphate rock on public land may be leased from the Government under the terms of the Mineral Leasing Act of 1920 , subject to the regulations of the Bureau of Land Management . Public interest in phosphate production is growing , as shown by an increasing number of applications for leases . Two mines are being operated steadily for the production of phosphate rock by companies that have also the necessary processing plants for the manufacture of fertilizer . Total western phosphate - rock production in 1947 is reported by the Economics Statistics and Division of the Federal Bureau of Mines to have been 1,193,000 long tons , mined in Idaho , Montana , and Wyoming . The average grade was 30.7 percent of contained phosphorus pentoxide (P205 ) ; the average value at the mines was $5.67 per long ton . Idaho contributed 905,000 tons , or somewhat more than 75 percent of western production . Western fertilizer plants took 23 percent of total production; 76 percent was exported . Strip mining accounted for 75 percent of the Idaho tonnage; the remainder was stoped from underground workings . Rock must contain a minimum of 30 percent P205 to be commercially useful for the production of superphosphate fertilizer by current acid treatment methods . Research by corporations and Government agencies has been directed toward the use of lower - grade ore . So far , only by smelting can rock containing as little as 25 percent P205 be used economically . Any development of processing or use pattern that would render the mining of , say , 20 percent rock profitable would have important effects in reducing the unit cost of mining . In the search for metallurgical improvements , consideration should be given to the saving of valuable components of the rock, such as vanadium and fluorine , both of which are present in the beds .

Oct 1, 1949

By Allen D. Look, Norman King

For many years, much thought and effort have been devoted to the achievement of safety in the use of explosives by those interested in the preservation of human life and the protection of property. As a result, we now have adequate rules pertaining to the safe use of explosives , which, if observed, would prevent many, perhaps ail , of the explosives accidents that yet occur . Although the rules respecting the use of explosives are believed to be well - known, many accidents occur because they are disregarded . The mental awareness aroused by a tragic accident usually will cause safety precautions to be taken for a while ; however , this awareness gradually disappears unless a sincere effort is made permanently to prevent similar accidents . Frequently, because safe methods are more irksome than unsafe methods , the lessons taught by accident experience are forgotten in a short time , vigilance is relaxed , and there is a gradual return to unsafe , easy methods of performing work. If the preservation of human life is important , the unfortunate experiences of others and the lessons taught by them should be applied to reduce unnecessary loss of life . The value of a life lost as the resuit of accident should be calculated not only from the monetary and humanitarian standpoint but also according to what the accident could contribute in the way of saving other lives and suffering . This saving of other lives can and will , if the lessons from unfortunate accidents are applied , convert a loss to a gain a gain of such magnitude that the accident victim could be considered

May 1, 1944

By W. P. Diamond, B. M. Bench, C. M. McCulloch

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were masured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 67° W - N 28° E (95° separation) for the north, and N 76° W - N 17° E (93° separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By William O. Vanderburg

This paper describing the mining practices at the Argonaut mine, Amador County, California, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The mining practices described are those used in exploiting the low-grade gold ores in the heavy and swelling ground that occurs on the Mother Lode belt. The author acknowledges the assistance of E. A. Stent, vice-president, James L. Fontenrose, cost clerk, Joseph Mohorovich, mine foreman, of the Argonaut mine, and of E. D. Gardner, supervising engineer, United States Bureau of Mines, Southwest Experiment Station, Tucson, Ariz.

Jan 1, 1930

By John R. Bartels

In laboratory testing, the Bureau of Mines established criteria by which common resin-grouted roof bolting systems can be evaluated and compared. Ultimate strength and stiffness were determined for nonten-sioned full-column, point-anchor, tensioned full-column, and debondable resin-grouted bolts, and for variations on full-column boltsn Bolt per-formances were compared using the performance of the 3/4-in full-column resin-grouted bolt as the standard. New and innovative systems can also be qualitatively compared against this standard. Since the medium into which a resin-grouted bolt is installed is one of the most important parameters affecting bolt performance, various host mediums were used in the testing: sandstone, concrete, simulated coal, simulated shale, and plaster. Bolt performances expected in other mediums can be inferred from the response patterns obtained in these mediums. Results indicate several functional differences among bolt types. Where resistance to shear is important, point-anchor bolts may outperform nontensioned full-column bolts at a lower cost. In medium-to soft-strength rock, tensioned full-column bolts perform best. Also, varying the resin-steel ratio seems to have little effect on the properties of a full-column bolt, when proper resin mixing is ensured.

Jan 1, 1985

By J. C. Johnson

In situ stresses are important input data for the design of safe, stable stope layouts and extraction sequences. However, it is commonly assumed that normal and shear stress gradients in a stress field are negligible and, consequently, that stresses are uniform throughout the region of analysis. To evaluate these assumptions and to provide input data for an analysis of a shaft pillar mining plan, in situ stresses were measured at the Homestake Mine, Lead, SD, using overcoring on hollow inclusion cells and borehole deformation gauges. These measurements were used with conventional least squares, best fit data reduction schemes. The results showed that normal stresses within the shaft pillar were less than, but comparable to, those estimated from finite-element modeling. Shear stresses were an order of magnitude less than normal stresses and varied considerably from site to site. Possible causes of this variability include effects of scale, elastic moduli, anisotropy, and axial strain. Because of the variability, it is not possible to determine the magnitude of horizontal stress gradients.

Jan 1, 2010

By C. V. Davis

In the lnvestlg::ìt1on of mAthods for aSS8.7ing platin",. conducted by the Bureau ot MinAs, reoent experiments have d~velopad tha~ with ce..tain orei, especially when thr, quantity Of platinum 1s eonlidarablfl, nit'!le acid w111 not etfßct a iepard-Han of platinum and pa11adium. 'lhe following m;lthod has been found to be accurate and to reiu1 t in a complete S''lun''ation of' th~3:l metals. It is therefo 1" '!eeommei:ed that 1 t ba followed rath::r- than the method of separation with nitrio acid, givèn in Technical Pape'! 270.* At line 22, pagi 14, of that paper, bAglnnlng with ~tarm th,~ metals '.'ith dilute¡ nitrio acid," strikE out the rest of the paragraph, and substttutt~ the pro_t cedure g1 ven below. ?lunder and Thuringer.. have developed mnt¡iods for th"i sflparation of palladium from all the platinum metals exoept platinum bj m ,ans of dlmethy- 19lyoxlme. They state that the~ is no action for several hours if an excess of dimeth¡lglyoxime is added to an aqueous solution of ohloroplatinic acid in the cold, alio that only on boiling is the platinum pTecipi ated ¡~d than only PST't of the platinum i srenoved from the sUut1on. They found that palladium 1s p~ecipi tated quati tat! vely in the oold as (CaH 4N40 Pd) which is insoluble tn water, dilute hydroohlorio acid, dilute acetIc aofd or in 50~ ethyl alcbhol. All of their pT'90ipi tations we~p Carl". ied out ~hile the solutions were being heated. This caused a pal"tia~recipltation of the platinum along wi th the

May 1, 1922

By John Gross

In connection with some investigations being made at '!'he Ra.re uid Precious 1ets.ls Station of the U, S. Bu.rea.u of Mines, at Reno, Nev., on the precipitation of gol'i and silver from cyanide solutions, it wa.s sug­ gested tnat the use of acetylene for this purpose be investigated, A pa.tent was iss·.ied to Fre<!.erick W. Martin and Frederick Stl1.bbs in 1900 covering the precipitation of precious metals from cyanide solu­tions by acetylene, The acetylene used in the tests described below wa3 made f'rom a. corr.:nercial cal ci \'!Z:l carbid.e, A r..umber of exper:me11. +,s rezul ted in more or lP.ss ccmplete pree;p1tatien of silver, -but 1n no case was a11Y gold precipitated. As silver acetylide, obtained by precipitatir.g the silver from an ar:::ncni'i\.Ca.l so1ut1on of silver n,. tra.te by acetylene, is yellowish white, esn:, solu'.)le in cyanide and hlghly explosive, and the pr9cip1tate ob­tain£ frcvm the cy'31lide sclutions was black, not tlubla L., cyanide and not explooive, it 'Na.s deid-,d. to ir.·.restigate the na.tur.e of the slJ.ver pre­cipit.te !rem the cy;r:iide solu·t:i.i,ns, !n prepa;.•i::lg a lge (!\,wrttity ,:f the preci-pi tte 1 t. wa, fo·und that a.fter c,:.\i;:1 ete prEc"'.pi tat ion cf the eil ver the !IOl ution con ta.ined soluble eulphic.e • Thia p:!:'O'lided a el f!W "lt·d. a.ft er apr,ropri-9.te tests the preeipita.te VIO,I proved to 'be ailver sulphide.

Apr 1, 1922

By J. O. Lewis

"The significant facts in the problem of the relation between the production of crude petroleum, and the ever-increasing demand for petroleum products are that in spite of continually increasing production, improvements in methods of refining and utilization, and heavy increases in imports, demands grow still more rapidly and we seem always faced with a shortage at hand or lust ahead. On the other hand, our foremost authorities warn um of entirely inadequate domestic reserves. Looking abroad we find some large fields and many of speculative promise, 'tut the situation is complicated by international relations and demands by other countries which promise to be even more insistent than oars. This is the situation, then. We can not rely upon our own Crude Petroleum to meet the Ever Increasing Demand for Petroleum Products.I wish to follow this somewhat alarming statement by saying at once that the Bureau of Mines is not pessimistic in facing this situation. To my mind those who discuss the oil situation may be placed in three categories; the pessimists, the optimists, and the super-optimists. The pessimists I call those who see darkly and will concede no possibility of solution. According to them a few years will see the automobiles piled in windrows of 'dilapidated junk, I have no sympathy with this point of view and deem it vicious and entirely unwarranted.The optimists I term those who believe that there is a solution and that we shall be able to meet all of our reasonable requirements for as far into the future as can be foreseen, yet who recognizes that this desired end can not be attained without prevision and energetic effort.The super-optimists are those who will say to you, ""There is nothing to this talk of shortage, whenever we have needed oil we have always found it and always will."" To these gentlemen the possibility of an inadequate supply of oil is as incomprehensible as the possibility of the extinction of the passenger pigeon was to the early settlers who saw flocks that hid the sun for days during their passage. The passenger pigeon disappeared within two generations thereafter, and I deem this point of view as being perhaps more vicious than that of the extreme pessimist. It seems to me it is nothing less than improvidence lulling us into a false sense of security. There is an old proverb to the effect that ""The Lord helps him who helps himself."" I believe that we shall solve the oil problem, but I do not think it will be solved by vague optimism. It is going to call for our most energetic efforts and I believe we shall have to do a lot of ""helping ourselves."""

Oct 1, 1920

By Willis Beckering

The Bureau of Mines designed a cell having four variable compartments in series to facilitate analysis of multicomponent mixtures. Use of the cell considerably decreases the time required for differential absorption analyses. A solution of a major component is placed in each compartment, and the light absorbed by each of these components is varied by increasing or decreasing the path length of the appropriate cell. Simple calculations then establish the amount of the component present. In analyzing unknown mixtures, compensation is made for compounds known to be present, and the differential spectrum representing components not accounted for is recorded and analyzed.

Jan 1, 1966

By M. J. Ferrante

Low-temperature heat capacities and high-temperature enthalpies were determined calorimetrically for Na2Cr04, A reversible transition was found at 700° K with an isothermal heat of transition of 2,263 cal/mole. High-temperature X-ray diffraction analysis showed that the transition was a crystal change from the low-temperature orthorhombic form to the high-temperature hexagonal form. At 795° K the hexagonal form had the parameters a, = 5.691 and co = 7.478 A. Powder diffraction data for the high-temperature form are given and possible structures discussed. The melting point was determined to be 1,065° K with a heat of fusion of 5,810 cal/mole. Enthalpy and entropy increments from this investigation were combined with other data from the literature to calculate enthalpies of formation, free energies of formation, and equilibrium constants of formation from 298° to 1,400° K. Equations that represent enthalpies above 298° K are given.

Jan 1, 1972

By E. P. Youngman

Gold and precious stones were mined in Egypt in prehistoric times. This mining, carried on at intervals, extended over thousands of years, until about 1300 A. D. Then ensued a dormant period of several hundred yoars. In the mean- time Europe made great rogress in mining practice, metallurgy, and geology and sent out various expeditions during the nineteenth century to investigate ancient mines. But the exploratory work produced no material results, and not until the beginning of the present century did actual mining recommence. The reopening of old gold mines in Rhodesia aroused interest in London and Paris, and these cities provided the capital necessary for the investigation of the ancient minee in West Africa and Egypt. Speculation resulted in the division of most of the uncultivated area of Egypt and the Sudan into huge concessions, and a number of expeditions were made; but after an unprecedented activity in West Africa, roaction set in, and the flow of capital ceased. The concession- aires, mostly individuals with insufficient capital and with a misconception of the initial difficulties of communication, water supply, and labor, allowed

Jan 1, 1932

By X. Shi, N. S. Dala, V. Vallaythan

"Cellular damage induced by silica dust is known to be associated with increased fragility and destabilization or destruction of the cell membranes. The mechanism by which silica dust effects biological membranes is still unknown. Using the ESR spin-trap methodology, we find that hydroxyl radicals are generated in aqueous suspensions of freshly ground silica. The amount of the radicals generated depends on the extent of grinding and ""freshness"" of the dust. Using linoleic acid as a model lipid, we show that the silica dust causes lipid peroxidation via ·OH, 02-, or linoleic acid related radicals as intermediates. Catalase and superoxide dismutase inhibit the formation of these radicals. The results suggest that free radicals associated with freshly ground silica and the related lipid peroxidation of the memberanes may be the starting point of the silicotic processes.INTRODUCTIONDespite considerable-effort over the years, the mechanism by which the quartz particles exert their toxic action on cells and the process(es) by which these actions progress to fibrosis are still not fully understood (1,2). It is generally thought, nevertheless, that the interaction of the quartz particles with the cell membranes is the starting point of the silicotic process (3). We felt that the mechanism of the membrane damage by quartz might involve oxygenated free radicals because (a) a suspension of quartz particles in contact with alveolar macrophages has been reported.(4,5) to initiate an enhancement of lipid peroxidation, defined broadly as the ;oxidative deterioration of polyunsaturated components of lipids, and (b) hydroxyl (·OH) radicals are known to be capable of peroxidation by abstracting hydrogen atoms from cell-membrane lipids (6) and initiating lipid peroxidation in lysosomal membranes (7). Moreover it is known that exposure of cell membranes, fatty acids and unsaturated food oils to ionizing radiation, which generates ·OH. radicals, causes rapid peroxidation (6). Earlier studies o~ the aqueous chemistry of quartz suspensions have reported detection of HzOz (8), implicating the formation of ·OH radicals as transient species, but, we are not aware of any report of the detection of ·OH radicals in quartz suspensions and this provided the motivation for the present undertaking. Since it is known that, because of their high reactivity (hence short life time) in aqueous media, the ·OH radicals cannot be detected via electron spin resonance (ESR) directly (9,10), we have used ESR combined with the spin-trap methodology (9) for studying the •OH formation."

Jan 1, 1988

By William H. Pomroy, Shail J. Butani

"This Bureau of Mines publication presents a statistical analysis of official U.S. Mine Safety and Health Administration (MSHA) metal and nonmetal mine fire reports from 1950 through 1984, plus accounts of selected nonreportable fires (less than 30 min and no injury) and opinion data on fire hazards from mine safety directors. Fires were analyzed by time trends, ore type, ignition source, burning substance, location in mine, equipment involved, means of detection, duration, number of injuries and fatalities, mining method, and successful extinguishing agent. The leading ignition sources were electricity in underground fires and engine heat in reported surface fires. The most frequent burning substance was combustible liquids for all nonreportable fires, reported surface fires, and reported underground fires from 1978 to 1984. For underground fires reported prior to 1978, timber was the leading burning substance. Mobile equipment was the type most frequently involved in both underground and surface fires. Underground fires occurred most often in haulageway or drift areas, and reported surface fires occurred most often in plant and mill buildings, while most nonreportable surface fires occurred in other areas. The most common methods of extinguishment were water hose lines for reported fires and dry chemical handportable extinguishers for nonreportable fires. INTRODUCTIONIn support of the Bureau of Mines research on mine fire protection, two separate baseline studies on mine fire incidents have been prepared. The first study addressed coal mine fires. The results of that study are summarized in the Bureau's Information Circular 8830, ""A Statistical Analysis of Coal Mine Fire Incidents in the United States From 1950 to 1977."" This second report, addressing metal and nonmetal mine fires, is the companion to IC 8830. Together, these two reports provide a comprehensive, factual summary of the mining industry's fire experience.This report, like IC 8830, covers (1) MSHA fire incident reports, (2) records of nonreportable fires (less than 30 min and no injury), and (3) mine safety directors' opinions on fire hazards. The MSHA fire reports provide the most reliable, objective, and accurate historcial record of the major noncoal mine fires that occurred during the study period (1950 through 1984). However, MSHA fire reports alone understate the true magnitude of the fire problem because metal and nonmetal mines have been legally required to report fires to MSHA only since 1968. Although some fires were reported prior to 1968, doubtless a great many were not. Also, the reporting regulations that took effect in 1968 specify that only fires lasting 30 min or longer or involving an injury need to be reported. MSHA fire reports are thus limited in scope by MSHA's legal authority. In order to provide a more comprehensive data base, it was also necessary to gather and analyze mine company records of nonreportable fires."

Jan 1, 1986

By Louis C. Brichta

The Rush Creek district of Marion County, Ark., has had a more or less continuous record of zinc production over the past 40 years. The ore has come from many small mines working on oxidized and semi-oxidized deposits found in the Everton formation where that formation forms the present surface rock. Prospecting has been restricted to the hillsides above the creek levels, the actual ore outcrops being the guides. Little attention has been paid the possible sulfide zones. In August 1942, the United States Geological Survey and the Bureau of Mines recommended exploration of the Powell and Cotter formations, which underlie the Everton, for which purpose the Survey had previously located 18 proposed drill-hole sites in geological structures that seemed favorable to are deposition.

Jan 1, 1949