Search Documents

By C. Stephan, E. Weiss, J. Trackemas, M. Sapko

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory (PRL), in collaboration with the Mine Safety and Health Administration (MSHA), the mining industry, and seal manufacturers recently conducted a series of full-scale experiments within the underground experimental mine at PRL’s Lake Lynn Laboratory. The purpose of the experiments was toe valuate the explosion-resistant characteristics of several new seal designs for rapid deployment during mine emergencies. These seals can be deployed in 6 to 10 hr and are capable of with standing explosion overpressures in excess of 140 kPa (20 psi). These novel seal designs use available mine materials, do not require conventional rib hitching, and, most importantly, can substantially reduce exposure time for coal miners during sealing and mine recovery operations.

By Manuel Gomez

Areal distributions for ash, total sulfur, and sulfur forms were developed for the top 12 inches, the middle section, the bottom 8 inches, and the total seam of Pittsburgh coal in southwestern Pennsylvania. The sulfur and ash exhibit an apparent high local variability. As a general rule, both the sulfur and ash show high concentrations in the top 12 inches and in the bottom 8 inches of the seam relative to the concentrations observed in the middle section of the seam. The high-low sulfur and ash concentrations in the top 12 inches of the seam are not coincident with the high-low sulfur and ash concentrations in either the middle section or the bottom 8 inches of the seam. With respect to sulfur and ash, it is suggested that the top and bottom sections of the Pittsburgh coal may reflect both a syngenetic and epigenetic origin. Present data support the belief that paleotopography controlled Pittsburgh seam deposition. Evidence is presented to show that channels were cut at various times into the semilithified sediments that buried the Pittsburgh seam. In this channeling process, portions of the Pittsburgh coal may have been eroded away. Following channel development, the lower part of the Pittsburgh sandstone filled the complex system of braided channels to produce the "want areas" encountered in present mining operations. In localized areas of the Pittsburgh seam, impingement of Pittsburgh sandstone may be responsible for the lateral displacement of the coal. Information of this type becomes important in the assessment of exploration data, in the development of a quality control system for mine output, and in mine life planning.

Jan 1, 1974

By Peter F. Strong, Robert L. Lagace, Alfred G. Exslie

The theoretical study of WF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer is the concern of this paper. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. The theoretical results are compared with published measurements. This work was part of an investigation of new ways to reach and extend two-way communications to the key individuals who are highly mobile within the sections and haulageways of coal mines.

Nov 14, 1974

By C. W. Owings

Two problems perplex many coal-mine operators and employees. Is coal-mine dust harmful to breathe; and, if so, is it possible to keep the concentration below the danger point? The medical profession is not unanimous in its opinion of the danger of breathing bituminous-coal dust, but there appears to be ample and increasing evidence that coal-mine dust can be harmful if breathed in large enough doses for long periods. The question of controlling the dust at the point of formation is still unanswered in the minds of many in the mining industry. However, results of limited studies conducted by the Bureau of Mines in 9 bituminous-coal mines indicate that a full-shift average exposure of workers should not exceed about 20 million dust particles per cubic foot of air (m.p.p.c.f.) and that concentrations can be held within this limit without too much difficulty. Furthermore, these studies indicated that an exposure in the neighborhood of 40 m.p.p.c.f. should not be exceeded for an individual operation and that it is possible to hold within this ceiling.

Jan 1, 1957

By W. N. Marchant

The Bureau of Mines improved removal of selenium from zinc smelter acidic gas scrubber effluent by using zinc dust to precipitate soluble selenium prior to lime neutralization. Lime neutralization alone decreased selenium in the waste water from, typically, 6 parts per million to 2 parts per million, whereas the use of zinc dust precipitant gave an effluent containing less than 0.1 part per million of selenium. The waste treatment operation first was developed on a laboratory scale and later was successfully tested at a smelter site on a 1-gallon-per-minute basis. During the research a simple and rapid means was developed for determining selenium in waste water; the technique enabled visual semiquantitative selenium determinations that later were confirmed quantitatively by X-ray fluorescence.

Jan 1, 1978

The National Institute of Occupational Safety and Health has classified diesel exhaust as a potential human carcinogen. Though standards for diesel particulate matter (DPM) in the work place have not been established, concern for the health of miners is prompting mine operators to consider methods for reducing worker exposure to diesel exhaust. Approach One of many methods for reducing DPM being investigated by the Bureau of Mines is the use of additives in diesel fuel to improve combustion. Research Results Three fuel additives have been tested in Caterpillar and Deutz diesel engines which are similar to types used in underground mines. One iron-based additive containing ferrous picrate had no effect on emissions. A second iron-based additive containing ferrocene reduced DPM between 5 and 45 pet depending on engine operating conditions. The 37-pct reduction for an 8-minute duty cycle, which includes a wide range of transient loads and speeds, is considered to represent in-mine performance.

Jan 1, 1990

By Richard H. Spencer, Warren G. Bender

Since the passage of the Coal Mine Health and Safety Act of 1969, the Bureau of Mines has made many advances in mine communications. These efforts have resulted in the following developments and demonstrations: • Surface-to-surface electromagnetic transmission of baseband voice signals through overburdens as deep as 600 feet. This transmission was achieved with equipment from the Interim Mine Rescue and Survival System Program, and demonstrated that baseband voice communications could be obtained through these overburdens in the absence of mine-generated noise; that is, when the mine power system was shut off. However, during mine operational conditions, the mine-generated noise proved to be so large that effective baseband voice communications to the desired depths could not be effected. • The development of beacon transmitters for locating trapped miners. This work was again the outgrowth of the Interim Mine Rescue and Survival System. Extensions of this work have led to reliable detection and location of trapped miners to depths of 1000 feet. The system, which makes use of a loop antenna deployed where the trapped miner is located, uses low-duty-cycle, tone-burst transmission. Portable tuned receivers and loop antennas are used on the surface to determine the location of the trapped miner. An extension of this work has led to a call-alert paging system concept, wherein a transmitter, similar to that used in the trapped miner system, is used to audibly and/or visually alert key mine personnel carrying pocket receivers that they are wanted at the nearest mine telephone. In addition, a roof-bolt paging system has been developed, wherein commercial paging and mine carrier phone equipment are used in conjunction with a long-wire "roof bolt" antenna to page individuals and relay to them short voice messages.

Jan 7, 1975

By John A. Breslin

Three scale models of coal mine entries and mining machines were constructed by the Bureau of Mines to study the effects of ventilation parameters on dust concentrations where mining personnel would be working. A one-fifth-scale model of a coal mine entry with a drum-type continuous-mining machine and a one-sixth-scale model of an entry with a twin-borer-type machine were used as well as a one-fifth-scale model of a longwall face with a double-drum shearer. Methane was used as a tracer gas to simulate respirable dust in the models. The distance of the end of the brattice or tubing from the face was found to be more important than the airflow rate for the drum-type machine. Dust reductions greater than 90 pct were shown to be possible with a secondary ventilation system used with the twin borer and a dust collector mounted on the longwall shearer. Cutting-head speed had a significant effect on concentrations at typical positions of miners with the drum-type machine and longwall shearer but not for the twin borer.

Jan 1, 1976

By M. J. Kovalik

The effects of the process variables on the production of chemical coke on a chain grate stoker, a type of traveling grate, were studied. Six bituminous coals, ranging in volatile matter from 16.7 to 43.8 percent, were successfully carbonized, yielding chemical coke with acceptable physical properties. The coke yields were dependent on the volatile-matter content of the coal. The air fuel ratio had the most marked effect on the yield and characteristics of the resultant coke, and the general furnace performance. Results can only be predicted; the actual yield and quality of coke obtained from any given coal can only be determined by actual tests using the optimum processing variables to obtain a coke with minimum volatile-matter content and to retain as much of the fixed carbon in the original coal as possible.

Jan 1, 1967

By B. J. Scheiner

As part of its mission to reduce pollution associated with mineral production, the Bureau of Mines is developing a dewatering technique for phosphatic clay waste that uses a flocculant, polyethylene oxide (PEO). This flocculant forms strong, stable flocs, which can be partially dewatered on a static screen and dewatered further on a rotary screen. Using this technique, a field test unit (FTU) was operated at a nominal 100 gal/min. Consolidated phosphatic clay material containing 20 percent solids was produced when feed slurries of 3 percent solids were treated with 0.69 pound of PEO per ton of feed solids. Pit and column tests indicated that the PEO-treated material continued to dewater; compacted products containing 40 percent solids were obtained after 45 days.

Jan 1, 1981

By Isaac A. Zlochower, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) conducted a study of the explosibility of various metals and other elemental dusts, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafnium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties-from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly "refractory" elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechnic ignitors. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from "-1550K for tin and tungsten powders to "-2800K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures.

By Daryl E. Radcliffe

Ninety-seven roof bolts were instrumented with strain gages and resin-grouted in three areas of the Bear coal mine, Somerset, Colo., by the Bureau of Mines. Measurements taken with these instruments indicate roof support is achieved through a combination of point suspension and resistance to vertical and horizontal stresses caused by localized shearing in the roof. The localized shearing results in bending of the bolts, yielding due to high vertical stresses, and the transfer of high loads to the bolt head or plate.

Jan 1, 1980

By D. S. Colby

The productive capacity of natural gasoline and cycling plants in the United States or. January 1, 1954, was 926 thousand barrels per day, according to the Bureau of Mines biennial survey. This represented an increase of 114 thousand barrels per day during the 2-year period since the last survey. In the previous 2-year period, capacity had increased 164 thousand barrels per day. The total number of plants increased from 521 on January 1, 1952, to 535 on January 1, 1954. The number of operating plants increased from 506 to 521. The major increases in capacity took place in Texas, Illinois, Oklahoma, Louisiana, and New Mexico, with the absorption-type plant continuing to account for most of the new construction. In 1954, however, 6 plants reported using a refrigeration process whereas only 1 plant reported this in 1952. The number of operating compression-type plants continued to decline and combination plants showed a decline this year because a number of these plants were reclassified as absorption-type.

Jan 1, 1954

By Manuel Gomez

The purpose of this study was to evaluate the feasibility of using statistical response surface regression analysis to predict the sulfur and ash distributions and the washability characteristics of coal along a seam in advance of mining. Prediction equations were developed with experimental data from channel, bench, and core samples from the Pittsburgh coal seam in Greene County, Pa. It was not possible, with the available experimental data, to construct mathematical models to predict ash and sulfur concentrations between sample points. In the authors' opinion, however, the good agreement between experimentally determined and predicted values at given sample points demonstrates the usefulness of the method. More input data, such as geologic information, seam characteristics (rock-to-coal ratio), petrographic analysis, and chemical data, would perhaps make it possible to predict sulfur and ash concentrations and washability characteristics between sample points.

Jan 1, 1970

By Jack C. White

The Bureau of Mines, in its efforts to insure the continued viability of the domestic minerals economy, has been engaged for several years in research on the extraction of alumina from domestic, nonbauxitic resources. Hydrochloric acid leaching of kaolin is one of the more promising technologies being studied for recovering alumina for feedstock to existing aluminum smelting capacity; 93 pct of this feedstock is currently imported either as bauxite or alumina. Organics contamination of pregnant leach liquor, originating during solvent extraction for removal of iron from aluminum chloride solution formed during hydrochloric acid leaching, causes rapid deterioration of the semihard rubber lining of process equipment. These organics were removed by a skimming tank-coalescer-activated carbon adsorption system. Organic levels of less than 10 ppm from the coalescer and less than 0.5 ppm from carbon adsorption were achieved. Analytical methods employing CC14 extraction and infrared spectrophotometry were developed to determine the organic content of both the liquor and the carbon. Mass transfer zones delineated in the carbon columns provide adsorption data for the design of larger systems.

Jan 1, 1981

By Joseph Cervik, Maurice Deul, Albert Sainato

This Bureau of Mines report deals with water infusion of coalbeds, which can control methane emission at face areas during developmental mining and which may sometimes suppress dust. Studies show that water infused into the coalbed flows through the fracture system and displaces the methane in the fractures and prevents migration from the solid coal. Displaced gas migrates away from the face area that has been water infused and enters the return ventilation airways. A gradual decrease in methane emission is observed from the start of infusion until the infused zone is mined through. Depending on the permeability of the coalbed, infusion pressures ranged from 300 to 2,200 lb/in2. Face emissions in the Upper Kittanning coalbed were reduced by 89 pct; reductions of 38 to 79 pct were measured in the Pittsburgh coalbed depending on the relationship between the face cleat direction and mining direction. Respirable dust levels were reduced by about 75 pct on a longwall section in the Pocahontas No. 3 coalbed and by about 50 pct on a development section in the Upper Kittanning coalbed, but no statistically reliable reduction was found in the respirable dust levels in the Pittsburgh coalbed.

Jan 1, 1977

By R. P. Vinson, Abdurrahman Cetinbas, Joseph Cervik, M. G. Zabetakis

The periphery of longwall panels in the Pocahontas No. 3 coalbed is characterized by a zone of reduced permeability that inhibits the natural drainage of methane. A residual gas pressure of 105 psig was measured after 1 year in an isolated block of coal measuring 340 by 1,100 feet. The buildup of gas pressure within such large blocks causes methane problems during plowing operations. However, natural drainage holes drilled during development have been found to reduce the gas content of the coal in this coalbed by over 90 percent. The effect of water infusion on dust during plowing operations was investigated using existing methane drainage holes. These holes were cleaned of debris and a pipe was grouted into the hole for water infusion of the panel. Both total and respirable dust levels were reduced by 40 to 79 percent. Water infusion of the panel proved more effective than did the use of a plow-mounted spray sys tem.

Jan 1, 1974

By H. H. Schrenk, L. B. Berger

"INTRODUCTION The Bureau of Mines frequently receives requests for information and advice regarding the equipment necessary for establishing laboratories for the analysis of mine atmospheres. Such requests are made by mining companies, State mining departments, and other agencies concerned with the safety of mining operations. In many instances it is desired to install a complete laboratory, which will necessitate purchase of suitable gas-analysis apparatus and all the minor but important accessory equipment needed to carry on this type of work. Although publications that describe methods and techniques applicable to the analysis of mine atmospheres are available, it is not within the scope of such publications to give detailed information on laboratory equipment or design. Persons unfamiliar with laboratory practices and gas-analysis procedures may find it difficult to decide upon the proper equipment for their particular needs and to itemize the various accessories that must be obtained to set up a complete laboratory.The purpose of this circular is to discuss the different types of equipment that may be used in the analysis of mine atmospheres, with particular regard to the application and limitations of each type. Information on the various accessory equipment needed in a laboratory for the analysis of mine atmospheres is given also, and suggestions on laboratory design are included. As much of the necessary equipment may be obtained from laboratory supply houses, the information should aid in arriving at estimates of the cost of proposed laboratories.The procedures involved in the analysis of mine atmospheres are not described; such information is contained in publications referred to in this circular."

Feb 1, 1948

By Raymond P. Maloney

The Rhyolite mercury prospect is on the south flank of Juninggulra Mountain--a large rhyolite intrusive in the Kuskokwim River region about 36 airline miles northwest of Red Devil, Alaska. Bulldozer trenching by the Bureau of Mines exposed bedrock at intervals in a 2,000-by 3,000-foot area where previous prospecting by the owners had disclosed abundant float and several in-place stringers containing cinnabar in widely varying amounts. The additional trenching indicated that the mercury mineralization in the limited area investigated was confined to erratically distributed short stringers and to small lenses, occurring in discontinuous zones in numerous silica-carbonate dikes and sills or along their altered contacts with sedimentary rocks. The geologic relationship of the mercury-bearing silica-carbonate dikes and the nearby rhyolite intrusive is similar to that existing at several other mercury mines and prospects in the. Kuskokwim region. The depth of over-burden and the presence of permafrost were serious obstacles to bulldozer trenching, and only a comparatively small part of the mineralized area was thus investigated.

Jan 1, 1962

By C. W. Owings, J. J. Forbes

"INTRODUCTION The recent coal-dust explosions in Illinois and Indiana have again brought forcibly to the attention of mining men the fact that mines which liberate little or no methane can have widespread explosions, if dry and dusty conditions exist and if adequate measures are not taken to control the dust hazard by rock dust¬ing or use of water.Even though rock dust has been used more or less extensively for more than 20 years as a means of limiting or preventing coal-mine explosions, many mine operators have requested information on rock dusting and means of allaying coal dust at its source. The purpose of this circular is to summarize available information on these two methods.COAL MINES TO BE ROCK-DUSTEDAll nonanthracite coal mines must be rock-dusted, except those mines or locations in a mine that are too wet or too high in incombustible content to propagate an explosion.Coal dust that contains 20 percent or more moisture may prevent ignition or propagation of an explosion. Such dust can be molded in the hands, and under such condition the roadway would be considered muddy. Mine dust that is only damp is not wet enough to prevent propagation of an explosion. Beads of water standing on accumulations of dust are not indications that the dust is wet. Only those mines or locations in a mine in which the coal dust can be molded in the hand need not be rock-dusted."

Jun 1, 1947