Search Documents

By L. W. Higley

Procedures were developed for reclaiming high-temperature alloy scrap in the form of standard cobalt-base alloy. A cobalt-base, multicomponent, high- temperature alloy, such as S-816, can be successfully melted from scrap, and its specified chemical composition can be retained. Induction furnace melting in a controlled atmosphere was used to obtain ingots that were subsequently fabricated by impact forging to provide specimens for heat treatment and testing. Of the numerous metal elements in S-816 alloy, only small quantities of molybdenum were lost in the melting operation as finally developed. Test results indicated that the scrap material, after melting, forging, and heat treatment, was equivalent in room-temperature tensile strength, in high-temperature creep and stress-rupture properties, and in chemical composition to commercially produced S-816 alloy made from virgin material.

Jan 1, 1963

By T. R. Jolley

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: I. Which coals either as mined or after beneficiation by conventional preparation are chemically suitable under present standards for producing metallurgical coke. 2. Which coals require special and more intensive treatment in preparation than is now practiced. 3. Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation by present-day methods. This report is one in the county series that describes the preparation characteristics of the coals of Bell County, Ky.

Jan 1, 1957

By Martin Hertzberg

The Bureau of Mines 8-liter flammability system was used to study the effectiveness of a variety of powdered inhibitors in preventing the propagation of explosions of coal dust or methane in air. Over 35 different chemical additives were evaluated against Pittsburgh seam pulverized coal. The least effective inhibitors were the carbonates, which required mass additions in the range of two to three parts inhibitor to one part of coal dust in order to prevent propagation. The most effective inhibitors were the derivatives of ammonium phosphate, which were effective quenching agents at additions of only one part inhibitor to four parts of coal dust. Alkali halide powders were of intermediate effectiveness. These laboratory-scale results are in good agreement with full-scale mine experiments in all cases where detailed comparisons have been made. Data were also obtained for the effectiveness of several of the same powdered inhibitors against methane-air explosions. Their relative order of effectiveness and the concentration ranges required for quenching the gas explosion are comparable to those measured for coal dust explosions. Data are also presented for the effectiveness of N2 and CF3Br addition. Some preliminary data are also presented for powder addition to methane burner flames. Those data are compared with other burner data and evaluated in terms of their relevance to explosion tests.

Jan 1, 1982

By Harold R. Newman

The performance of Ecuador's mineral industry continued to be affected not only by depressed oil prices in recent years but also by natural disasters. In March 1987, Ecuador canceled foreign debt payments for the rest of the year and appealed for international aid because of a series of earth-quakes that destroyed villages and crippled the nation's oil industry. The earthquake destroyed a key section of the country's main oil pipeline and forced a halt to production and shipment of Ecuador's most important export product. Ecuador produces 240,000 barrels of oil per day and exports 144,000 barrels daily. Oil accounts for 60% of the nation's hard currency earnings. The Government of Ecuador asked the Organization of Petroleum Exporting Countries and other oil-producing countries to assume Ecuador's oil sales commitments. Ecuador agreed to pay the countries back in an equivalent amount of oil when it was able to resume exports.

Jan 1, 1989

By Annie G. Smelley

The Bureau of Mines, U.S. Department of the Interior, as part of its mission to effect pollution abatement, conducted research to devise means for disposing of phosphatic clay wastes and reclaiming mined land. Part of the investigation was performed in a cooperative research project with 10 phosphate companies in Florida. The colloidal properties of the phosphatic clay suspensions, called slimes, make them difficult to dewater and dispose of without impoundment storage aboveground. Various reagents to flocculate and dewater these plant wastes were evaluated, and a polyethylene oxide polymer was found to function in a specialized flocculation dewatering technique. The flocculation dewatering method was investigated in bench-scale batch tests and applied in continuous dewatering tests using standard mineral-processing equipment. In continuous tests at feed rates of up to 58 liters per minute, wastes at 4 percent solids were dewatered to about 20 percent solids. About 0.8 kilogram of polymer was used for each metric ton of dry waste clay solids; processing time was about 4 minutes. Requirements for the treatment system are (1) proper mixing of the clay-waste feed and flocculant, (2) rapid removal of water as it is released, and (3) physical manipulation to promote cohesion of solids.

Jan 1, 1979

By Edward D. Thimons, Jay F. Colinet

NIOSH conducted a strategic planning effort to identify those areas in mining with the greatest research needs. Data analysis and stakeholder input identified the need to reduce worker exposure to respirable crystalline silica dust as a high priority area. MSHA dust sampling data were analyzed to target the mining commodities and occupations with the greatest percentage of samples containing silica above compliance levels. In response, the Pittsburgh Research Laboratory (PRL) has implemented a multi-faceted research program to improve silica dust control for these problematic commodities and occupations. A review of silica compliance trends, PRL silica research programs, and recent control technology developments are provided here.

By Francis R. Redfern

Newton's method of solving a nonlinear equation is employed to develop a least-squares acoustic emission source location method in which the spatial residuals of the location equations are minimized. These residuals, related to the distances from the least-squares source location perpendicular to the surfaces described by the location equations, permit location error to be estimated to first order along the spatial axes. The solutions obtained by this method are the best spatial solutions to the location equations in the least-squares sense. Also presented is a procedure by which the geometrical control of a transducer array can be evaluated using the rate of change of source location with fractional velocity change.

Jan 1, 1982

By Norwood B. Melcher

This report describes preliminary experiments by the Federal Bureau of Mines on the practicability of adding raw pellets of taconite concentrate to blast furnace feeds. The usual industrial practice is to harden the pellets by heating before they are charged to the furnace. The Bureau research demonstrated that raw pellets could be successfully smelted in an experimental furnace with no significant change in coke consumption and only a moderate increase in dust losses. The dust loss was 43 pounds per ton of metal for an all-pellet charge, compared with 7 pounds per ton for an all-sinter charge. Raw taconite pellets undergo only slight degradation during charging to the furnace if 1 percent bentonite is used as a binder. INTRODUCTION Fines and concentrates must be consolidated or agglomerated into larger masses before they can be smelted in a commercial blast furnace. Such agglomeration is usually done by sintering, pelletizing, nodulizing, or briquetting. Sintering has been the more common practice, but with the advent of taconite concentrates pelletizing is increasing in importance.

Jan 1, 1960

By Raymond F. Helinski, Linda J. McWilliams, Sean Gallagher, Thomas R. Battenhouse, August J. Kwitowski, John R. Bartels, Dean H. Ambrose

This report examines the boom arm vertical speed for roof bolting machines to study a moving boom arm appendage at different speeds during different work scenarios. The goal of this study is to determine the impact of the appendage speed on the likelihood of the operator's hand, arm, head, or leg making contact, such as touching the moving appendage. The overall research goal is to reduce workers' risks to injury from exposure to underground mining machinery. Accident investigation reports from the Mine Safety and Health Administration do not usually contain enough information to aid in studying this problem, and lab experiments with human subjects are not feasible because of safety issues. As an alternative, researchers used a unique computer simulation model that uses a virtual human, vision tracking, and generates random virtual human motions and risky work behaviors. By using specialized software to simulate the computer model, researchers accurately identified potential hazards of tasks where it is not possible to perform experiments with human subjects. Results of a frequency distribution analytic approach show that, regardless of other variables, contact incidents were always greater when the boom was moving up, always greater on the hand, and always greater or the boom arm part of the machine. The reason why the subject experiences more contacts when the boom arm is moving up rather than down is that more risky behaviors occur during drilling and bolting when the boom is ascending. Results of a cross-tabulation analytic approach show that the 25th-percentile operators experienced more contacts than other operator sizes and had most of their contacts during a boom speed of 13 in/sec. The hand-on-boom behavior during drilling and bolting tasks experienced more contacts than other work behaviors, and both tasks had most of their contacts during speed 13 in/sec. The 60-in seam experienced more contacts than other seam heights and had most of the contacts during speed 16 in/sec. For univariate logistic regression models, seam height is the most important predictor of the probability of a contact. However, a multivariate logistic regression model predicted contacts are more likely with the both-knee work posture in the 60-in seam, a 25th-percentile operator compared to a 55th-percentile operator, and speeds 16 and 22 in/sec compared to 7 in/sec. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speeds greater than13 in/sec result in a substantial increase in risk to the roof bolter operator making contact. Speeds less than or equal to 13 in/sec are associated with a more modest relative risk of making contact, which represents a decrease in potential hazard. Virtual operator's response time has little effect on the number of contacts experienced. The mining industry can use the information in this study to reduce the likelihood that roof bolter operators will experience injury due to contact with a moving roof bolting machine's boom arm.

Jan 5, 2005

By G. W. Murrie, W. P. Diamond, S. W. Lambert

A geologic study of the Mary Lee Group of coalbeds in the Black Warrior coal basin was undertaken to examine coal stratigraphy and determine regional trends and extent of the coalbeds. The area investigated encompasses 835 square miles in Jefferson, Walker, and Tuscaloosa Counties, Ala. More than 700 core logs were used to construct a structure map, coal, interval, and overburden isopachs, and cross sections. There is evidence that structure affected sedimentation. Coalbed isopachs indicate the Mary Lee Group was deposited in fluvial-deltaic and low-lying coastal plain environments. The Mary Lee coalbed is the only coalbed which is continuous throughout the area, commonly with two benches which have a combined thickness of 2 to 12 feet. The Mary Lee coalbed changes rank in the basin from high- through medium- to low-volatile coal. The methane gas potential of the Mary Lee Group coals is estimated to be greater than 1 trillion cubic feet. There is an excellent correlation between the orientation of surface cleats with those measured underground in the Mary Lee coalbed. The face cleats roughly parallel the axes of the area's folds and trend northeast-southwest.

Jan 1, 1976

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the dust suppression technique of applying foam to face drilling and crushing operations in a gypsum mine. Previous attempts to achieve effective dust control on face drills using other techniques, such as dry collection and boom-mounted external water sprays, have not been successful. The largest problem encountered when using these techniques has been the lack of sustained effective dust capture at the face. Results for two faces studied show that injection of the foam through the drill steel provided an average dust reduction of 95 pct. However, the use of foam on the crusher provided no dust reduction at the operator's position (because of good local ventilation) and a 27-pct average dust reduction for two feeders at a location midway between the operator's position and the crusher. The conclusions obtained from this study are that (1) foam can be an extremely effective dust control technique when used on localized dust sources such as dust generated within a blasthole during drilling, and (2) foam is only marginally effective as a dust control technique when used on nonlocalized dust sources such as dust generated during the feeder-and-crusher operation.

Jan 1, 1981

By Charles E. Whieldon

This report presents the results of a study on part of the Smithfield oilfield, Wetzel County, W. Va. The primary purpose of the investigation was to determine the original and the present volume of stock-tank oil in the formations and to investigate the feasibility of waterflooding the Gordon Stray, Gordon, and Fourth sands underlying the I. D. Morgan lease. The study was based on laboratory core analyses, geophysical well logs, geologic considerations, and various field prediction data from the I. D. Morgan lease. The Bureau found that, of the three sands cored, the Gordon Sand was the best prospect for waterflooding, and that a properly engineered water flood should recover 136 to 230 barrels of oil per acre-foot from this formation.

Jan 1, 1967

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free- port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in determining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ton of coal, for a total of 190 to 400 billion cubic feet of methane in this coalbed in Fayette County.

Jan 1, 1977

By Richard J. Mainiero, Marcia L. Harris, James H. Rowland

In the past several years, there have been a number of blasting-related carbon monoxide migration incidents. In each case, there have been some common factors that appear to be related to carbon monoxide migration. Geology, heavy confinement of the blast, close proximity to the affected structure, and open pathways into the affected structure are just a few. Prince William County, VA is an area undergoing a boom in suburban development. In the year 2001, more than 4,050 new homes were constructed within the county.1 In the new housing development located in Bristow,VA, trench blasting was utilized to excavate proposed sewage and utility lines. On November 8, 2002, a trench blast was conducted for the installation of utility lines. Later that evening a carbon monoxide detector alarmed in a nearby house. The gas company and fire department sampled for carbon monoxide and measured 100 ppm and more than 200 ppm on the first floor and in the basement respectively. Subsequent efforts to prevent migration of CO into the nearby homes met with mixed results. The only reliable technique for protecting neighbors from CO appears to be the placement of CO monitors in the homes. The events are presented and discussed.

By J. J. Henn

A process is evaluated for recovering metallurgical-grade manganese are from the low-grade manganiferous iron ores of the Cuyuna Range, Minnesota. The process, developed by the Bureau of Mines, employs high-temperature sulfatization of the are to form manganese sulfate and reduction of the are to convert the iron to a magnetic oxide. The roasted ore is water-leached to dissolve the manganese sulfate, which is then separated from the leach residue, is crystallized, and is calcined to produce the manganese product. Iron is recovered from the leach residue by magnetic separation, and is pelletized and calcined to produce byproduct iron ore pellets. The fixed capital cost for a plant yielding a product containing 100 tons of manganese per day is $19.6 million on a mid-1970 basis when the raw are contains 4.84 percent manganese. The estimated operating cost of the plant is $211 per ton of contained manganese. Graphs are included to show the effects of ore cost and varying manganese content of the raw ore on the estimated operating cost.

Jan 1, 1972

By John L. Hill

"The Bureau of Mines is conducting research on the causes and methods for control of cutter roof failure in underground coal mines. This hazardous ground control problem exposes miners to the danger of falling roof rock and frequently results in massive roof failure. This report outlines the probable causes of cutter roof failure, which are proposed based on field investigations, numerical model analysis, and in-mine observations. Traditional methods of control are presented, as well as innovative methods based on mining concepts developed during earlier years of coal mining history. The report can be useful to a mine operator for assessing the causes of cutter roof failure on a site-by-site basis and for predicting the probability of its occurrence. A process is presented for selecting an optimum control method that includes both traditional and innovative control techniques for each of the various causes of cutter roof failure. INTRODUCTIONGround control research conducted by the Bureau of Mines is designed to develop technology that will aid in reducing the frequency of accidents associated with poor ground control conditions. Cutter roof failure often poses a safety hazard to miners and causes delays in production while massive roof falls are cleaned up and unstable roof is resupported. Implementation of control measures reduces the threat of injury to miners and prevents production delays.The definition of cutter roof failure used in this report separates this unique type of failure from other ground control problems, to aid in the analysis of the causes and in the development of control methods. The definition is as follows:Cutter roof failure in mine roof rock is a failure process that initially begins as a fracture plane in the roof rock parallel to, and located at, the roof-rib intersection. The fracture propagates upward into the roof over the mine opening at an angle usually steeper than 60° from the horizontal.The mappable extent of cutter failure may range in length from only a few feet to several hundred feet and may traverse entry-crosscut intersections without change in direction. Once initiated along the roof-rib line, a cutter may propagate away from the roof-rib line of one side of a room, cross the roof span, and continue along the other side of the room. It is important to note that this definition excludes a similar type of failure (sometimes referred to as ""kink roof') that has comparable characteristics but occurs in the center of the entry. (The reasons for this distinction are discussed in the ""Background"" section.) Researchers refer to the cutter failure discussed in this report as ""classic"" cutter roof failure; except for short deviations across intersections and entries, initial failure is confined to the roof-rib intersection."

Jan 1, 1986

By F. W. Wood

Ingots of zirconium and other highly reactive metals such as titanium and hafnium produced by the consumable-electrode arc-melting process require conditioning before forging or rolling. A nondestructive, arc-conditioning technique has been developed as a substitute for lathe conditioning. The technique employs en electric arc under an inert atmosphere to fuse surface metal on the sidewalls of ingots without seriously affecting the general quality of the ingots. Advantages of the practice are Increased yields, lower accumulation of inferior scrap, and actual cost savings. The work cited in this report was done on zirconium. INTRODUCTION The consumable-electrode arc-melting process as practiced at the Bureau of Mines3 4/ has proved to be a technique for producing sound, homogeneous, commercial-size ingots of zirconium and its alloys. Ingots produced by this process, however, have as a characteristic a layer of partly fused metal on the sidewall to a depth of 3/16 to 3/8 inch. To prevent extension of surface imperfections during forging, the ingots are ordinarily conditioned by removing defective material in a lathe. If the metal were less reactive or the requirements less severe, the machine chips could be recycled and remelted. However, zirconium, being so oxygen sensitive, is contaminated by merely being machined despite extensive cooling of the tool bit. Further, being contaminated with oxygen, the chip metal upon remelting is 10 to 25 Brinell-hardnese numbers harder than the ingot from which it was machined. For this reason, the ingot specifications for naval reactor use have prohibited remelting machine chips, except as required for starting pads. Again, were zirconium less costly or less in demand this ever-increasing pile could be burned to oxide and recycled through the Kroll sponge process. Economics do not favor this, as melting feed stock has an estimated increase In value over oxide of about $8.80 per pound of contained zirconium. The efforts of the Bureau to solve the problem have been directed along two lines: To reduce the contamination of the machine chips produced and to reduce the quantity of the chips produced. This paper presents the technique developed to reduce the quantity of chips produced by arc-conditioning the remelted ingot.

Jan 1, 1955

By Lisa Steiner, Robin Burgess-Limerick

In 2004, there were 646 underground coal mines in the USA employing 37,445 miners. These mines reported 3556 injuries to MSHA that year - 17% were associated with bolting machines (593 injuries), 8% with continuous miners (283 injuries), and 4% each with Scoop/LHD (1 51 injuries), shuttle cars (134 injuries), and personnel transport (145 injuries). The use of the frequency of reported injuries for the prioritization of risk control strategies has limitations because of the tendency to underestimate the importance of relatively rare but high-consequence events. Injury reports also underestimate the contribution of risk factors such as whole body vibration, which have a long-term cumulative contribution to an elevated risk of injury. However, taking these limitations into consideration, the results of the injury narrative analysis suggest the following hazards as the highest priority for elimination or control: • rock falling from supported roof • inadvertent or incorrect operation of bolting controls • handling continuous miner cable • collisions while driving LHD/Scoop, shuttle cars and personnel transport • rough road while driving or traveling in LHD/Scoop, SC & PT

By A. Gene Collins

During recent years the interest in trace and minor constituents of oil-field water, petroleum, and their associated reservoir rocks has increased. The metals copper, nickel, lead, manganese, iron, zinc, and cadmium are not determined routinely in oilfield brine analyses. Determination of these metals and subsequent correlation of these data should yield information to aid 1n the interpretation of the origin of different waters. The methods of analyzing oilfield waters have several potential applications: (1) Aiding in the search for petroleum; (2) identifying sources of intrusive brines; (3) controlling corrosion; (4) controlling produced water; increasing knowledge of the geology of subsurface formations; (5) identifying incompatible waters in waterflooding operations; (6) increasing the knowledge of the flow of oil, gas, and water in underground formations; and (7) aiding in the identification and location of valuable mineral reserves. Some brines contain enough valuable minerals to be recovered commercially.

Jan 1, 1962

Research workers from the Bureau of Mines and industry met with other government and industry representatives at the Mont Chateau Lodge, Morgantown, W. Va., on May 30-31, 1973, to discuss the current status of methane control in eastern U.S. coal mines. The opening remarks, the eight technical presentations, and the discussions of the members of a government-industry panel are published here for the benefit of those concerned with the control of methane in coal mines. In addition, an introduction has been added to present the background of work in this field.

Jan 1, 1973