Search Documents

By Frank G. Horino

This report describes an instrument designed by the Bureau of Mines for quantitatively identifying texture of rock surfaces produced by grinding or extremely rough surfaces beyond the range of commercial surface measuring instruments. The transducer for the instrument is a linear variable differential transformer that converts mechanical motion caused by surface roughness, waviness, and lay to an electrical output. The electrical output is recorded graphically as an X-Y plot of the line traversed on the rock surface. Details of the synthesized device and its calibration are given. The sensitivity of the unit is 2 percent of the scale setting of the amplifier. The horizontal scale is adaptable from ¼ inch to 15 inches of specimen length with a sensitivity of 0.01 inch if a 10 to 1 magnification is used and 0.1 inch if a 1 to 1 magnification is used.

Jan 1, 1968

By A. D. Garman

This paper presents one of a series of digests of foreign mining legislation and court decisions which is being prepared in advance of a general report relative to the right of American citizens to explore for minerals and to own and operate mines in various foreign countries . This interpretation of the laws of Japan has been prepared from the best available information in Washington but is released subject to correction and amplification , if necessary , by the proper American diplomatic and consular officers to whom it is being referred through the courtesy of the Department of State . It is based on the law and regulations of 1905 as revised in December , 1915 , and translated by J. de Becker , LL.B. Occasional words and phrases quoted herein are accordingly taken from this translation and have not been checked against the original . The references are to the law ( as distinguished from the regulations ) unless otherwise stated .

Jul 1, 1930

By G. St. J. Perrott, N. A. Tolch

"PURPOSE OF TESTSThe propulsive strength4 developed by the Cardox blasting device depends on the thickness of disk, weight of heater element, and weight of carbon dioxide charge. It might be supposed that the maximum weight of carbon dioxide that can be charged into the shell should give the greatest strength. However, according to the ballistic pendulum, the maximum weight of carbon dioxide with certain conditions of heater and disk has less propulsive strength than a smaller charge; in one condition of test a loss of 39 per cent in propulsive strength was noted. It is therefore of interest to study the effect of the variables that determine the strength of Cardox.ACKNOWLEDGMENTGrateful acknowledgment is made to A. B. Coates, associate mechanical engineer who developed the testing method for measuring pressures in the Cardox shell.DESCRIPTION OF DEVICEThe Cardox blasting device as fully described by the bureau in Report of Investiga¬tions 2920 (1929), consists essentially of hollow—steel shell, cylindrical in shape, an electrode, valve assembly, shearing disk, and discharge cap. The shell is prepared for use by inserting a heater element, closing the open end with a shearing disk, and screwing in place the discharge cap. The charge of carbon dioxide enters the shell through the electrode.The heater element is fired by an electric igniter of the match—head type. The heat released by the heater element completely gasifies the carbon dioxide and raises the pressure of the gas until it is enough to shear the disk."

Apr 1, 1931

By A. J. Kraemer

"During the past several years a great deal of discussion has centered around the question of the permissible limit of sulphur content in fuels for automotive and aviation motors. Under certain conditions of operation, sulphur in motor fuels causes the formation of corrosive substances which attack bearings, wrist pins, and other parts of engines. On the other hand, in making gasoline from certain stocks, the gasoline fraction normally contains a relatively large proportion of sulphur compounds. By the generally used processes of reducing the sulphur content, a significant part of the gasoline fraction is lost as motor fuel, and added expenses are entailed for chemicals, labor, and other process costs. This condition has been an economic burden to some refiners of high-sulphur crudes. In some instances the treating losses have been rather severe and the treating costs relatively high, but the data presented in this paper indicate that the reduction of sulphur content of motor fuel is a problem to a relatively small number of refiners and of little or no concern to the remainder; in fact, more than 90 per cent of the 153 samples analyzed passed the Federal specification requirement, Which limits the sulphur content to 0.10 per cent. 3This report is based upon the results of an examination for sulphur content, Doctor test, copper strip corrosion, and color of the samples collected during January, 1930, for the twenty-first semiannual gasoline survey of the Bureau of Mines. The results of the gravity ad distillation tests of the survey were published as Report of Investigations 2995. The numbering of the samples given in this report is the same as in Report of Investigations 2995; for example, No. 25 of this report is the same sample as No. 25 of Report of Investigations 2995."

Jun 1, 1930

By Robert W. Freedman

The Bureau of Mines investigated methods of analysis of free silica in respirable dust, including both work done at the Bureau of Mines and work done elsewhere. The review covers both coal dust and noncoal dust, taking into account both existing and proposed chemical and spectroscopic procedures.

Jan 1, 1971

By R. W. Holliday

To determine the copper and nickel content of reported ore occurrences in the Chippewa mine near Rockmont, Douglas County, Wis., the Bureau of Mines reopened and sampled the old shaft and workings during the summer and fall of 1953. Occurrences of native copper near Rockmont and others near Gordon, also in Douglas County, Wis., are in lava flows, which extend from the Keweenaw Peninsula of Upper Michigan southwest across Wisconsin and into Minnesota. Sporadic attempts have been made to find additional economic copper deposits in these flows since profitable mines were developed in Upper Michigan nearly 100 years ago. The Rockmont and Gordon areas were explored extensively more than 50 years ago. More recently, from August 1944 to duly 1945, an occurrence near Gordon was investigated by the Bureau.2/

Jan 1, 1955

By R. W. Lewis

The Federal Bureau of Mines Boulder City Metallurgy Research Laboratory conducted experiments in order to develop a spectrochemical method for determining the concentrations of impurities In high-purity tungsten. This report presents a procedure, developed by these experiments, for determining 19 impurities in high-purity tungsten. Metal samples were thermally converted to the oxide, mixed with graphite, which was prepared and mixed with an internal-standard element, and excited in a d.c. arc. Sixteen of the impurity elements were determined with one set of conditions, using germanium as an internal standard. Lanthanum was used as an internal standard in the tests for boron and chromium. Molybdenum required the substitution of sodium chloride for the graphite and the use of copper electrodes. Data on the precision of the method are included in this report. The coefficients of variation vary considerably but average about 15 percent. Higher concentrations of impurities than those investigated may be determined with some modifications of the testing procedure, provided attention is given to the possibility of interelement interferences.

Jan 1, 1961

By J. D. Marchant

The Bureau of Mines studied solid-state electromigration to determine the value of the technique as a method of purifying cerium metal. Cerium metal in bars 6 inches long and 1/2 inch in diameter was refined at 600° C by solid-state electrolysis to remove iron, copper, and manganese. Iron and manganese were electrotransported to the anode and copper was electrotransported to the cathode. The concentration of iron at the anode of a cerium bar was 800 times greater than the concentration at the cathode. The concentration of manganese at the anode was twice the value at the cathode. The concentration of copper was 170 times greater at the cathode than at the anode. A radiotracer technique was used to follow the iron migration in the cerium metal. Molybdenum, silicon, and aluminum impurities were not electrotransported.

Jan 1, 1967

By William H. Schiffbauer, Ph. D. Mowrey

Proximity warning devices can improve workplace safety by alerting workers when they are in a hazardous area near moving equipment. Industrial work sites often present extreme challenges to safety-based proximity warning devices. Many commercially available types of proximity warning sensors and systems can be rendered useless when covered with mud, ice, snow, ore, rock, and other material. The list includes radar, ultrasonic, capacitive, and visual types of sensors and systems. Addressing these shortcomings, NIOSH personnel have developed a patented active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) which employs lowfrequency, low-power magnetic fields which are quite impervious to severe environmental conditions. A shapeable wire loop antenna which provides the marker of dangerous work areas, has been mounted on a continuous mining machine and was mounted inside 1.3-cm thick angle iron. This loop antenna was exposed to more than six months of active underground coal production, which included being covered by and scraped over with tons of rock, sprayed by a continuous stream of water, and immersed in thick mud. After six months the loop antenna showed signs of wear, but was still capable of performing its intended function. The HASARD system is now being applied to other industrial applications and is showing much promise, especially in harsh environments. This paper details the system, describes the tests that have been done, and mentions other areas where it can benefit the safety of industrial workers.

By D. Harrington

The desirability of efficient control of air currents, and the necessity of supplying metal-mine workers with better and safer working conditions, has created an active interest in metal-mine ventilation, especially in recent years. This paper discusses the subject both with regard to efficiency and economy, as well as safety and health. It is based on personal observations of the writer from over four year's study of metal mines in six States, in which more than 50 mines were visited. Many of these were studied in detail; in all several thousand working places were examined, and readings taken relative to ventilation run into the tens of thousands.Object of ventilating metal mines:Whereas in coal mines ventilation is generally regarded as essential, in many metal mines, especially shallow ones, the operators pay little attention to ventilation, or ignore it altogether. Recent shortage of labor, and numerous accidents to which State compensation laws have directed attention, are causing metal-mine operators to regard ventilation more seriously, especially in deep, large mines.There is, in fact, greater necessity for adequate ventilation of metal mines than of coal mines. The latter require air currents to remove explosive gases and the fumes of explosives, but metal mines, in addition to the need of removing fumes of explosives, and occasionally explosive gases, frequently have need of removing dusts dangerous to health, reduction of high temperatures and high humidity, and removal of inert but unhealthful gases like CO2 and nitrugen. The generally accepted superior healthfulness of coal miners as compared with metal miners, is probably due in large part to the better air circulation in working places of coal mines.

Jun 1, 1920

By N. N. Moebs

The atmosphere in part of an air-sealed coal mine was monitored continuously through a drill hole for oxygen content to determine the effectiveness of sealing a mine against the entrance of air and the major force that caused the phenomenon of mine breathing through the overburden. The differential pressure across the seal and the barometric pressure on the outside also were recorded. A general correlation, obtained between the oxygen level, differential pressure, and barometric pressure, indicates that changes in air pressure are the cause for periodic replenishment of the oxygen in the mine. Mine effluent quality was determined by conditions in many sections of the mine and could not be related to the oxygen level at the drill hole.

Jan 1, 1972

By J. W. Stevenson

The Bureau of Mines investigated the influence that atmospheric pressure changes exert in a gassy coal mil on a ventilating air current with a system of bleeder entries. During the season when abnormal barometric fluctuations usually occur, recording instruments monitored the air current ventilating an active coal-producing area. It HL he rate of coal production caused a more significant change in methane concentration than did barometric change. The hazard that accompanies methane release due to expansion of the gob gases during atmospheric lows was minimized by the effective bleeder system.

Jan 1, 1966

By John S. Dunning

This paper is one of a series describing methods and costs of recovering sand and gravel from deposits in the United States and deals directly with the operations of the Atlas Sand, Gravel and Stone Co. at Farmington, Conn. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local expenditures only and not total production costs. It is recognized that publication of total costs might in some instances cause embarasement to individual producers, as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations may ensue.

Jan 1, 1933

By R. V. Ramani, S. Shankar

"The phenomenon of re-entrainment is seen in environments such as sand dune formation, soil erosion, fugitive dust emission and the spread of radionuclides from accidents involving nuclear weapons. A thorough review of existing literature reveals that work on re-entrainment of dust in mine atmospheres is scant. The present study was undertaken as a part of ongoing research at the Generic Mineral Technology Center on Respirable Dust at the Pennsylvania State University on the development of methods to predict ambient dust concentrations in mine atmospheres (Ramani, 1983). The contribution of re-entrainment to the spatial and temporal concentration of dust in mine airways is being studied. The research has included wind tunnel and in-mine studies.A set of seven experiments was performed under controlled conditions in the US Bureau of Mines' Lake Lynn Laboratory mine. Two types of source coal dust, anthracite and bituminous, were subjected to various airflow rates and were subjected to walking by two different individuals. Six sets of instruments were used along the test section for sampling airborne particles. The average air velocity just above the coal dust bed varied between 2.1 to 3.2 m/sec.Due to re-entrainment as a result of the airflow conditions, the average respirable dust concentration in the center of the mine airway increased to 0.09 mg!m3 (standard deviation= 0.03 mg/m3)from an initial value of 0.02 mg/m3. The concentration of all (total) airborne dust increased to 0.17 mg/m3 (standard deviation = 0.10 mg/m3) from an initial value of 0. 02 mg/m3. The action of people walking, however, caused higher amounts of re-entrainment. The average concentration of respirable and total dust at the center of the mine airway increased to values of 0. 28 mg/m3 (standard deviation of 0.12 mg/m3) and 1.53 mg/m3 (standard deviation of 1.0 mg/m3), from initial values of 0.03 and 0.05 mg/m3, respectively. Jr was observed that the dust concentrations were much higher near the floor, immediately at the end of the coal-dust bed.Depending on the level of activity and the amount of dust deposited in the mine airways, re-entrainment may become an important source of airborne dust in areas away from the point of actual mining."

Dec 1, 1996

By J. M. Mutmansky

"This study analyzed laboratory comminution techniques for respirable mine dust generation and the properties of the resulting dusts. It was the objective of the study to determine the suitability of the resulting dusts in reflecting the properties of natural airborne dust. This paper deals specifically with the amount of contamination introduced into the generated dust as a result of abrasion when using nine different grinding methods. The analysis was made by comparing the content of 25 chemical elements in the lab-generated dusts with the same elements in the airborne coal mine dusts. It was found that all the lab-generated dusts possessed contamination but that several methods produced smaller percentages of contamination and that the residence time in the grinding device was an important factor in the contamination levels. INTRODUCTIONDust in the atmosphere is a health hazard and a major source of occupational diseases in the coal mining industry (Anon., 1980; Merchant, Boehlecke, and Picket-Hamer, 1986). It has been shown that coal workers' pneumoconiosis (CWP) is directly related to the inhalation and accumulation of respirable coal dust in coal miners' lungs. In order to effectively protect coal workers from coal dusts, we must have a clear understanding of dust properties including dust generation and dust-lung reaction mechanisms. This requires extensive biomedical research. Dust related research often requires large samples of respirable coal dusts to be collected, either for repeated experiments or stored for future reference. Unfortunately, current sampling instruments are not able to meet this demand. Ali a result, laboratory-generated coal dust ls frequently used as a substitute for coal mine dust in biomedical and other research applications. Now, the questions are how close the characteristics of laboratory-generated dusts are to those of mining-generated dusts and which equipment is moat appropriate for research dust production in the laboratory . These are some of the interests of this research project. The primary objective of this project was to find a laboratory technique which can generate coal dusts possessing properties similar to coal mine dust with respect to particle size distribution, chemical composition, and particle shape and morphology. However, this paper will focus only on the chemical compositions of the prepared dust samples and try to identify the sources of chemical contamination from various size reduction processes."

Mar 1, 1992

By George S. Rice

"It is well known that the lost coal left in the ground in mining, under such conditions that recovery is practically impossible, constitutes a large proportion of the coal in the beds worked. A recent estimate, in a paper on ""The World's Fuel Supply"" presented by Prof. L. P. Breckinridge, of Yale University, before the Annual Meeting of the. American Society of Mechanical Engineers, places the average loss in bituminous coal mining as one-third left in the ground.The bald statement that there is a loss of one ton of coal for every two recovered may seem to those not familiar with coal mining to imply inexcusable and wanton waste. Perhaps a better way of expression is in terms of total recovery rather than in terms of losses. Many mine superintendents and mine owners will readily concede that their total recovery may be only 60 to 75 per cent, but to state that they are wasting 25 to 40 per cent arouses antagonism. The suggestion is of willful waste, whereas the majority of the operators try to the best of their ability to get a high recovery under the adverse and complex conditions that confront them. These involve natural, commercial, and labor conditions, and the requirement in many cases of boundary pillars under railroads and buildings, which may be called for in the deed or lease, or in the absence of specific exemption in the deed or lease, the common law requirement that a surface owner is entitled to the support of the surface."

Apr 1, 1921

By John C. Franklin

A radon survey was made at five different locations in the Twilight mine near Uravan, Colo., to determine chances in radon concentrations in an inactive mine. Data were taken with a continuous monitor set for 1-minute count periods and readings were taken 24 hours a day for 9 days. The 12 readings per station each hour accurately showed how t w radon concentration varied during the day. From the data collected from the intake portal to station 4, the average radon emanation rate was estimated at 18 picocuries per second per square foot (pCi/sec/ft3). A daily cycle in radon concentration was detected that apparently was related to barometric pressure change.

Jan 1, 1976

By D. L. Nussear, W. E. Wallace, N. N. Clark, M. Gautam, G. Hong-Guang

"Results from a study directed towards identifying and measuring the mutagenicity of diesel exhaust particulate matter involved in mining exposures, especially those which may synergistically affect genotoxic hazard, are presented in this paper. Particulate matter emissions from a diesel engine, representative of the ones found in underground mines, were sampled and assayed to determine the genotoxic potential as a function of engine operating conditions. Diesel exhaust was diluted in a multi-tube mini-dilution tunnel and the particulate matter was collected on 70 mm fluorocarbon coated glass fiber filters as well as on 8"" x 10"" hi-volume filters. A six mode steady state duty cycle was used to relate engine operating conditions to the mutagenicity potential.Protocols developed for using a primary component of pulmonary surfactant as a medium for collecting and applying respirable particulate material to cells for mutagenicity testing offer a true representation of in-vivo delivery of such respired aerosols to pulmonary cells and the genetic material within . The surfactant dispersion technique is discussed in this paper. Methods have been developed to sample and assay the diesel soot and diesel soot/mineral dust complexes which would not compromise the surface and physical properties of the particulate material."

Nov 1, 1995

By R. B. Moore

The story of helium is one of the romances of science . Probably nothing , except perhaps radium , compares with it in human interest . Helium is one of the best examples of a discovery in pure science that has wide commercial application . In 1868 , an eclipse of the sun was visible in India , several scientific men who were in India making observations of the eclipse turned a spectroscope for the first time on the solar chromosphere - that part of the atmosphere of the sun , about 10,000 miles deep , which merges into the corona . A bright yellow line was observed and was thought at first to be due to sodium . Janssen showed , however , that this line was not just the same as either the D or D₂ line of sodium, although it was extremely close to these lines , hence he suggested that the new line have the designation D₂ . Frankland and Lockyer decided that Dz was due to an element in the sun not previously discovered on the earth , and suggested for it the name "Helium" from the Greek work " Helios " the sun . For several years nothing more was done in connection with this element . In 1894 , Sir William Ransay , in conjunction with Lord Rayleigh , made his memorable discovery of argon in the atmosphere , which was announced at the British Association meeting in the same year . After this discovery , Ramsay looked for other sources of the element . Through Sir Henry Miers , he learned that Dr. W. F. Hillebrand , of the United States Geological Survey , had obtained an inert gas from certain uranium minerals , which gas he had decided was nitrogen . Ramsay believed that part of it might be argon ; he obtained from Hillebrand for experimentation , a sample of the mineral , cleveite , one of the uranium minerals , and after extracting gas from the mineral and purifying it , he ran it into a spectrum tube . The lines obtained ' were , however , different from those of argon; among them was the bright yellow line noted by Janssen . Thus was terrestrial heliun discovered .

Jun 1, 1922

By Paul M. Tyler

A great variety of substance that differ widely in chemical, mineralogical, and physical properties are loosely linked under the generic term "clay", but for the average man all that matters is whether a given material can be sold or used profitably. So-called "clays" range in texture from true clays and allied minerals that are typically "fat" or sticky to fine sand. Sand and other strictly silicious materials, such as tripoli and diatomite, are not clays in any sense; but many commercial clays are strictly loams, for they are intermediate in texture and always contain a mixture of minerals, though the term "loam" has little commercial usage except in foundry work. Even pure kaolinite, ordinarily considered the typical "clay substance", recently was found to exist as three distinct minerals; and each of these, in turn, exhibits variations in particle size and other physical attributes. Probing with the X-ray and employing other modern tools and techniques, scientists are tracing the patterns of molecules and finding chemical and physical phenomena that seem to disclose the causes for the markedly different behavior of the various aluminum silicates with varying proportions of combined and adsorbed water that are the essential ingredients of commercial clays; but rule-of-thumb definitions and enforced reliance upon empirical tests of actual samples still hold sway. In addition to the hydrated simple silicates of aluminum, almost all clays contain quartz, feldspar, and mica with varying amounts of organic matter and, in addition, other impurities - such as iron, manganese, and titanium oxides - that may discolor them sufficiently to render them unfit for certain important uses. The white clays are generally the purest, but no two clays are really alike, and great care must be exercised to maintain a reasonable uniformity in successive shipments even from the same deposit.

Jan 1, 1938