Search Documents

By C. Özgen Karacan

This study presents the results of core-log analyses from the exploration boreholes, the analyses of face advance rates, and the results of downhole monitoring studies performed in gob gas ventholes for calculation of changes in hydraulic properties in the longwall overburden at a mine site in southwestern (SW) Pennsylvania section of Northern Appalachian Basin. In the ?rst part of the study, coal measure rocks in overburden strata were analyzed and the locations where possible fractures and bedding plane separations would occur were evaluated. In the second part, the hydraulic conductivities were computed by two different slug test analyses methods using the water level changes measured in gob gas ventholes as longwall face approached. Hydraulic conductivities were analyzed with respect to the changes in overburden depth, the locations of the borehole, and mine face advance rates. These data were used to interpret the potential productivities of the gob gas ventholes as a result of fracturing and changes in hydraulic conductivities. The general results showed that the probability of fracturing and bedding plane separations in the overburden increase between strong and weak rock interfaces. Also, the probability of bedding plane separations increases as the interface is close to the extracted coal seam. Evaluation of slug tests showed that the hydraulic conductivity developments in the boreholes and their potential production performances are affected by the underground strata and the roof materials. In situations where the roof material is stiff and thick, the development of high permeability fractures around the borehole will be less. Results also indicated that borehole location with respect to face position affects the fracturing time and permeability evolution as well. Greater overburden depths generally cause earlier fracturing as longwall face approaches, but eventually result in lower hydraulic conductivities and potentially less effective boreholes. Increasing mining rates also resulted in generally lower hydraulic conductivities in the overburden. The results of this study were intended to improve the interpretation of gob gas venthole performance and to provide better siting of these boreholes.

Jan 1, 2009

By S. H. Ash

Tunnel driving is recognized as one of the most hazardous of occupations; this is a reflection of the high accident severity rates and resultant high compensation and similar costs in this industry. Most tunnels are driven by contractors who bid for the jobs, taking into consideration the prevailing industrial insurance rates at the time the bids are placed. After the bid is secured the contractor then attempts to complete the job at the minimum cost to himself. In a sense the accident-cost item is fixed for at least one year when a policy is secured. Time is generally an important factor not only for the contractor, but also for the insurance carrier and the assured. If the assured represents a private interest, the cost burden usually is ultimately placed on the general public which avails itself of the service contemplated; if the project is a governmental enterprise the cost burden unquestionably falls upon the general public involved and on the general tax payer. For these reasons it is of vital interest to the public that accidents not only be kept at a minimum as a humanitarian objective, but also because the accident-cost burden, too frequently not even realized and considered to the degree that it should be, can assume proportions that materially affect the cost of the enterprise. The basic industrial insurance rate for tunneling in California in 1932 contemplated an earned premium of 12.12 percent of the labor pay roll. The State has been particularly engaged in large construction enterprises, some of which involve high accident cost rates, notably structural-steel bridge building, which contemplates an earned premium of 19.65 percent of the labor pay roll. When this figure is compared with the much lower rates that apply to other industries it is apparent that a heavy toll in human wreckage is taken by such engineering projects, which must be viewed as monuments to human suffering as veil as to human achievement.

Jan 1, 1933

By Christopher Mark, Anthony T. Iannacchione

Falls of ground continue to be one of the most serious causes of injury to U.S. miners. Of the 256 fatal injuries that occurred in mining between 1996 and 1998, 52 (20%) were caused by falls of ground (Table I). Falls of ground affect some sectors of the mining industry more severely than others. For instance, nearly 40% of the 98 coal mine fatalities between 1996 and 1998 were caused by falls of ground. Underground miners are at much greater risk than surface miners. Nearly half (45 out of 101) of underground mine fatalities were attributed to roof, rib and face falls, while less than 5% of the 155 surface fatalities were caused by falls of highwalls or slopes. Sources of Data All of the injury data examined in this study were derived from MSHA’s Fatal Investigation Reports (www.msha.gov)and the MSHA accident database. Because falls of ground often result in serious injury, MSHA Fatal Alert Bulletins and Fatal Investigation Reports provide a useful snapshot of ground control issues in the mining industry. MSHA requires that mines file a report on every reportable accident that occurs, containing information on the accident’s location, severity, classification, activity, and nature of injury, etc. A short narrative is generally included as well. Accident reports can be searched by many of the above fields. From 1996 to 1998, miners suffered a total of 55,096 injuries, which ranged in severity from death (degree 1) to injuries with no days away from work nor restricted duty (degree 6). Six percent of the total injuries were from falls of ground, including machine accidents where caving rock was coded as the source. As the data in Table II indicate, 98% of all non-fatal fall of ground injuries occurred in underground mines, with underground coal mines accounting for 83% of the total. Table II also shows the distribution non-fatal fall of ground injuries by severity and commodity. The injuries are classified into Lost Time Injuries that resulted in permanent disability (degree 2) or days off work (degrees 3-4), and Injuries Without Lost Time that resulted in no more than restricted duty (degree 5-6). Overall, groundfall injuries appear to be more serious than other types of mining injuries. 65% of all ground fall injuries resulted in lost time compared to 54% of all types of mining injuries.

By M. R. Peterson

The U.S. Bureau of Mines investigated column flotation for recovery of a high-grade fluorite (CaF2) concentrate and byproduct concentrates from the Fish Creek fluorite deposit in Eureka County, NY. The recovery scheme consisted of (1) grinding the ore to minus 48 mesh, (2) fluorite rougher and cleaner flotation, (3) desliming the rougher fluorite flotation tailings at 20 Jjm, (4) mica flotation, and (5) silicate rougher flotation. Acid-grade fluorspar, mica, free silica (Si02) sand, and low-grade beryl (Be3Al2S~018) concentrate were produced in a 100 lb/h continuous column flotation unit (CCFU). The highest results achieved were %.6-pct CaF2 recovery in a fIrst cleaner concentrate containing 99.7 pct CaF2. Beryl recovery was as high as 92 pct at a grade of 5.3 pct BeO. The silica sand, which assayed 98 pct Si02, was recovered as the rougher beryl flotation tailings. Collector reagent consumption was reduced 45 pct for fluorite and 58 pet for silicate flotation in comparison with bench-scale conventional flotation. All products were signillcantly improved in both grade and recovery over conventional flotation results, and the recovery scheme was simplifIed by removal of several stages of flotation in the fluorite and silicate flotation steps.

Jan 1, 1990

By Omotayo Kalejaiye

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRL 20-L and Fike 1-m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface-weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1-m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

Jan 1, 2010

Five conclusions that emerged from ADL's Contractor Noise Measurements Assessment done for the Bureau of Mines and the 7 December 1971 Bureau of Mines Contractors' Round Table Meeting in Boulder, Colorado were: ? a limited amount of good data has been obtained for characterizing the noise environment for electromagnetic (EM) coal mine operational/emergency communications systems; ? significant noise date gaps still exist; ? suitable instrumentation and data analysis methods are available for filling these data gaps; ? the immediate and most important data gaps should be filled by means of a timely field measurement effort that is purposely limited in scope and duration; ? this field measurement effort should preferably be carried out by a team knowledgeable and experienced in coal mine EM noise measurements.

Jan 1, 1972

By Elaine Cullen, Launa Mallett, Mike Jenkins, C. M. K. Boldt, Thomas Camm

The material in this Information Circular was presented at the National Institute for Occupational Safety and Health’s (NIOSH) open-industry briefing held during the 2004 Northwest Mining Association conference in Spokane, WA. The open-industry briefing discussed results of recently completed and on-going mine safety- and health-related research conducted at NIOSH’s Spokane and Pittsburgh Research Laboratories on the human side of mining—the miner. The first paper sets the stage for what mining has achieved and what we mean by “getting to zero.” The second paper, “Help Experienced Miners Become Great On-the-Job Trainers,” distinguishes between experienced miners and trainers. This paper provides some key concepts for turning great miners into great trainers. “The Power of Story-Telling in Getting Through to Miners” explains the history and importance of stories in the culture and training of miners. Finally, “Understanding Self in Stressful Working Environments,” describes the personal and social aspects of the working environment, much of which parallels familial theories. The downward trend of deaths in U.S. mining has been remarkable. The number of miners killed or injured each year has decreased steadily over the past 100 years. Some charts show these trends overlain with important events such as World War II and the Mine Safety and Health Act. However, this downward trend in mining fatalities has flattened out. How can you get to zero accidents? Do you concentrate on technological advances and equipment maintenance to avoid malfunctions? Do you concentrate on developing work processes and organizational structures that minimize risk? Do you combine them and take a systems approach that links one to the other with an evaluative loop? Safety efforts in mining have used all of these approaches. What more can we do to get to zero? Getting to zero will require two objectives: A clear and unshakeable belief that it can be done and attention to the human side of mining. Getting to zero is not a new idea; it has been used by mine companies and safety professionals for years as the safety goal. But getting to zero is not so much a physical goal as it is a belief that there are no insurmountable barriers to achieving the goal.

Jan 3, 2006

By W. R. Huff

This report describes the development and operation by the Bureau of Mines of a pilot plant designed for using high-volatile A bituminous coal-in-water suspensions as a source of preheated coal and superheated steam in the pressure gasification of coal with oxygen. Figure 1 on page 2 is a block diagram of the integrated gasification process, in which a total of 70 tons of coal was fed from slurry and gasified. The present work included (1) development of equipment and methods both for mixing pulverized coal and water to produce slurry and for pumping and metering the slurry at gasification pressure; (2) development of equipment for heating the flowing slurry and, because slurry that can be pumped produces more steam than is necessary as a gasification reactant, developing equipment for removing and metering the excess steam; and (3) demonstration of the process under actual gasifier operating conditions, at a coal rate of about 800 pounds per hour and gasification pressures in the range 100 to 300 pounds per square inch gage. By using the forced-convection principle, a flow of slurry made from a caking, high-volatile A bituminous coal can be continuously heated to 600° F. in a coil-type heater. The flow rate and concentration of the slurry and the temperature gradient along the length of the heating coil must be closely controlled. In a radiant-type heater, involuntary reductions in flow rate, even momentary, can lead to coking and plugging of the heater coil.

Jan 1, 1961

By Joseph W. Town

The Bureau of Mines conducted studies related to SO2 air pollution to determine attritioning rates, SO2 sorption rates, and sulfur loads that could be obtained on commercial alkalized alumina sorbent pellets. Fluidized-bed attritioning rates ranged from 0.025 pct/hr for alkalized alumina with a crushing strength of 4 kg to 0.075 pct/hr for 0.5 kg crushing strength mate¬rial. Airlift attritioning rates ranged from 0.50 pct/hr for 3 kg crushing strength alkalized alumina to about 3 pct/hr for 0.5 kg material. Attritioning rates for the commercial alkalized alumina were comparable to those obtained for sorbent pellets prepared in the Bureau of Mines laboratory. Sorption rates were related to S02 concentration in flue gas, temperature, and presence of nitrogen oxides in the gas stream. Sorption rates at 300° C were 0.35 X 10-6 gS/gp/sec (grams sulfur per gram pellet per second) in 0.045 pct so, gas, 5.1 x 10-5 gS/gp/sec in 0.34 pct SO2 gas, and 65 X 10-5 gS/gp/sec in 10 pct SO2 gas. For the 0.34 pct S02 gas, sulfur loads of 0.10 gS/gp (the projected load for regeneration) were obtained in 47 min at 130° C and in 116 min at 300° C. The presence of either NO or NO2 in the 0.34 pet S02 gas increased the SO2 sorption rates 2 to 3 times at 300° C, but had no effect at 130° C.

Jan 1, 1969

By John Durkin

Electromagnetic narrow-band signals were transmitted through the earth at 27 coal mines located throughout the United States. From those Bureau of Mines tests, apparent earth conductivity values were derived based upon a homogeneous half-space model of the earth. The derived conductivity values were found to be inversely proportional to the transmitted frequency and mine depth. A linear regression model relating the logarithm of the conductivity to the mine depth was formulated, and the results indicate that the mine depth can be an adequate predictor of the apparent earth conductivity above coal mines. Apparent earth conductivity was found to decrease with mine depth.

Jan 1, 1984

By John Durkin

Electromagnetic narrow-band signals were transmitted through the earth at 27 coal mines located throughout the United States. From those Bureau of Mines tests, apparent earth conductivity values were derived based upon a homogeneous half-space model of the earth. The derived conductivity values were found to be inversely proportional to the transmitted frequency and mine depth. A linear regression model relating the logarithm of the conductivity to the mine depth was formulated, and the results indicate that the mine depth can be an adequate predictor of the apparent earth conductivity above coal mines. Apparent earth conductivity was found to decrease with mine depth.

Jan 1, 1984

By Richard F. Hewlett

Computing average grade and tonnage either for an entire ore deposit or for individual blocks of ore is a continuing problem in mining. As part of a research program, investigating application of statistical techniques to mine sampling, Bureau of Mines engineers at the Denver Mining Research Center have made extensive use of an electronic digital computer for developing mine sampling theory, simulation of ore deposits, and analysis of mine sample and assay data. This report is one of a series describing use of the digital computer for rapid solution of computing problems in the mining industry.3 4 Development of a computer program to compute ore reserves by the commonly used triangular method was necessary so that results could be made available for analysis within hours.

Jan 1, 1963

By Henry Kreisinger, John Blizard

This preliminary statement presents some of the results of tests carried out at the Lakeside Station of the Milwaukee Electric Railway and Light Co. , by the fuel section of the U. S. Bureau of Mines , in cooperation with the research department of the Combustion Engineering Corporation of New York . The object of these tests was to determine the thermal efficiency , ease of operation , and other particulars of a boiler equipped with specially designed furnace and burners for burning powdered coal . The boiler tested haş 13380 square feet of heating surface , and is one of eight boilers equipped with the Lopulco powdered coal system supplying steam to two 20,000 -Kw . steam turbines in the largest power house burning powdered coal . Twenty- six tests were run at rates of heat transference varying from 4000 to 8000 B.t.u. per square foot of boiler heating surface , and the mean thermal efficiency attained was about 84 per cent , based on the gross calorific value of the fuel as fired . The efficiency varied little with the rate of steaming , and its high value is accounted for by the small loss from incomplete combustion and the small amount of excess air which varied from 5 to 36 per cent . The coal burned had a gross calorific value of about 11500 to 12800 B.t.u. per pound , contained 2 to 5 per cent moisture , 33 to 36 per cent volatile matter and 9 to 13 per cent ash, and was so ground thaf 89 to 95 per cent would pass through a 100- mesh sieve . The ash had a softening point of 2150 to 2450 degrees F. , but did not fuse together at the bottom of the furnace because it was partly protected from the flame radiation by means of a series of water tubes connected to the boiler which were placed between the fumace bottom and the flame, ..

Jan 1, 1923

By W. P. Diamond, A. C. Smith, J. A. Organiscak, T. P. Mucho

The U.S. Bureau of Mines conducted a worldwide literature review of bleederless ventilation practices to evaluate their use as a spontaneous combustion control measure in U.S. coal mines. Factors that must be taken into account in the design and use of these systems include seal construction, the use of ventilation control devices, the use of methane-drainage systems in gassy mines, and the ground control plan. Monitoring for the detection of spontaneous combustion and the control of methane when methane-drainage techniques are employed is critical to the successful use of a bleederless ventilation system. This report describes the types of ventilation systems used throughout the world and the spontaneous combustion risks associated with these systems. Methane-drainage systems used in conjunction with bleederless ventilation systems are discussed. Ground control considerations such as pillar design, entry stability, and seal usage are reviewed. Monitoring systems for spontaneous combustion detection, methane-drainage control, and behind seals are examined. Finally, methods for evaluating the spontaneous combustion hazard of a mining operation to determine when the use of a bleederless ventilation system is warranted are reviewed.

Jan 1, 1994

By M. H. Rinkenbach, C. A. Taylor

The detonating compound cyanuric triazide was discovered*** and patented**** by Erwin Ott, and on account of his claims, the Bureau of Ordnance, U. S. Navy, desired more complete data, so an investigation was made. The results obtained were such that the Bureau of Crdnance recommended publication thereof for the benefit of the explosives industry. Some of the patent claims regarding cyanuric triazide are as follows: 1. It is not poisonous in contradistinction to fulminating mercury and lead azide. 2. In contradistinction to the hitherto employed priming agents it is fusible, and its fusion point (94°C) is so low that the product melted by a single heating in water or steam bath, can be poured without danger in the capsule shell. It solidifies therein after cooling, and shows the density of 1.5. 3. It has been determined that the cyanuric triazide, in spite of its very much higher priming actions, is much less brisent then ful- minating mercury and lead nitride. 4. The chemically pure cyanuric triazide (C3M2) constitutes colorless crystals melting at 94°0., and is not volatile. It is not affected by cold water, and only slowly saponified by hot water. It is relatively insensitive to friction and not too strong concussion, but explodes by impact or when hea ted to 170°C., or when heated suddenly. It is not more sensitive to friction and shocks then fulminating mercury. 5. The preparation of the triazide is preferably carried out by acting with an excess of sodium azide in an aqueous solution; in the cold, on cyamric chloride gradually suspended in the said solution.

Aug 1, 1923

By C. R. Stephan, N. B. Greninger, S. J. Luzik

The U.S. Bureau of Mines conducted explosion tests on various full-scale cementitious bulkheads used in abandoned mine areas to evaluate the ability of the bulkheads to withstand gas explosion over-pressures of 20 psig. Tests were performed on 120-ft2 solid-concrete-block seals of varying thicknesses and designs. Of the seven solid-concrete-block seals tested, only the standard-type seal, having a 16-in thickness, keyed at the floor and ribs, all joints mortared, wedged at the roof, and a center pilaster, maintained its integrity when subjected to a 20-psig pressure wave. After being subjected to repeated explosions, the standard seal only showed a small hairline crack and had an air leakage of 87 ft3/min at a pressure differential of 1 in H2O. Tests were performed on cementitious foam seals of varying thicknesses and compressive strengths. Explosion tests have shown that 200-psi strength, 4- and 8-ft-thick seals can withstand a 20-psig pressure wave. At a pressure differential of 1 in H20, no air leakage was detected through the 200-psi, 8-ft-thick foam seal.

Jan 1, 1991

By G. S. Rice, R. V. Wheeler

"FOREWORDThe cooperative mine safety research program was carried on successfully in the year 1930 in a manner similar to that described in the report for 1929It is believed that the results of such fundamental work as is being done are unquestionably of great benefit in their application in coal-mining operations, in the saving of life and health of minera. The research result compared and checked by investigations in the two organizations, and further by large-scale tests, as in the Experimental Mine, give confidence to mine operators, miners and State mining officials in the findings of the various researches.The annual report of the contact officers of the United. States Bureau of Mines and the British Safety in Mines Research Board to the Director of the Bureau and the Chairman of the Board respectively, follows:Annual Reports for 1930 To: The Director, Bureau of Mines.The Chairman, Safety in Mines Research Board."

Sep 1, 1931

By Stuart Bjorklund

This paper is one of many reporting various aspects of the Bureau of Mines program initiated in August 1939 by passage of the Strategic Minerals Act J the scope of which was greatly expanded by subsequent legislation. In its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The occurrence of chromite in the Knik Valley near Palmer, Alaska, was brought to the attention of the Bureau of Mines in September 1941 by George Johnson, of Anchorage. At that time a preliminary investigation was made by Robert S. Sanford, an engineer of the Bureau of Mines. The area was investigated on June 4 and 5, 1943, by Henry R. Joesting and Leo H. Saarela, engineers of the Territorial Department of Mines. In August 1942, a second chromite occurrence, the Highway deposit, in the Knik Valley, was reported to the Territorial Department of Mines by John E. Ryan of Anchorage.

Jan 1, 1948

By G. R. Hopkins

"The average heat requirement per barrel of crude refined in the United States rose from 579,000 B. t. u. in 1940 to 584,000 B. t. u. in 1941. This marked the second successive year in which there was an apparent loss in fuel efficiency at refineries. This ""loss"" took place despite an increase in crude runs, which used to be an invariable indicator of a lower average.Probably the chief factor in the increased heat requirement in 1941 was the gain in the over-all gasoline yield from 43.1 percent in 1940 to 44.2 percent in 1941. Possibly another important factor was the further use of obsolete equipment to increase throughput.The refiners used more of all kinds of fuel excapt coke in 1941 than in 1940. However, the only fuels which increased materially in relative importance were refinery gas, which contributed 51.6 percent of the total heat units in 1941 compared with 50.7 percent in 1940, and natural gas, the share of which rose from 17.1 percent in 1940 to 18.0 percent in 1941. The changes in the percentages for the other fuels were as follows: Oil decreased from 25.7 to 24.1 percent; acid sludge fell from 2.7 to 2.5; coal remained at 3.4 percent; and coke (including steam) fell from 0.5 to 0.4 percent.New records for fuel efficiency were set in all three of the districts east of the Mississippi, namely, East Coast, Appalachian, and Indiana, Illi¬nois, etc. All the ether districts reported higher average fuel requirements in 1941, except the Louisiana Gulf and Arkansas-Louisiana inland.Since the year of the first statistics, the refiners have steadily increased their purchases of electricity. In 1941 total purchases were 1,862,996,000 kilowatt-hours, or 11 percent more than in 1940."

Apr 1, 1943

By Erik Sherer

Indonesia is poised to become a major player in the Pacific Rim thermal coal markets. Although the colonial Dutch developed numerous coal mines in the late 1800's for steamship bunkers and domestic fuel, Indonesia's coal industry has only recently begun to actively participate in the growing global marketplace. This export coal is primarily the result of the commercial development of coal mines in eastern Kalimantan by foreign contractors. From virtually no coal exports in the late 1980?s, Indonesia's coal industry has increased its exports to approximately 15 million metric tons (Mmt) in 1992. In 1992, Indonesia was the world?s sixth largest exporter of steam coal, By the year 2000, Indonesia projects that it will supply approximately 25 percent of the seaborne thermal coal requirements of the Pacific Rim countries. Although limited quantities of this coal may enter the European and U.S. markets, high qualities, low production casts, and favorable transportation rates will make Indonesian coals very competitive in the rapidly growing Pacific Rim markets. This study examines the Indonesian coal mining industry and compares it to the U.S. coal mining industry. This report is the sixth in a series of coal exporting country studies requested by the House Appropriations Committee. Previous studies examined the Colombian, Canadian, Australian, South African, Polish, and Venezuelan coal industries.

Jan 1, 1994