Search Documents

By David E. Siskind

The Bureau of Mines studied environmental blast effects in six occupied residential structures. Airblast, ground, and structure vibrations were measured both inside and outside residences for seven quarry production blasts. Walls and floors responded to the blast noise and vibration by shaking at their own natural frequencies, often with greater peak particle velocities than the ground outside the structures or their foundations. The vibrations of the houses generated noticeable internal noise, correlating with the arrival of the groundborne energy. The later arriving airblast wave was predominantly at low infrasonic frequencies (1.0 to 1.5 Hz) and had similar amplitude and frequency characteristics both inside and out-side the structures. Significant structural motions resulted from the air-blast overpressures for at least two of the seven blasts. The most severe airblast effect occurred at a house 1,800 feet from a 5,047-pound (200-lb/ delay) blast. This stucture was subjected to a peak 0.16-in/sec particle velocity and 130 dB(L) airblast. The wall of the second floor responded to the ground vibration and airblast by shaking at particle velocities of 0.15 and 0.28 in/sec, respectively. Analysis of these data and those from additional field studies will be used to identify appropriate, safe, and reasonable impulsive noise levels, measurement techniques, and factors of design applicable to minimizing the adverse environmental effects of blasting.

Jan 1, 1976

By D. W. Frommer

As one phase of a general problem of recovering sulfide slimes, mineral-dressing research was conducted on flotation tailing from the St. Joseph Lead Co., Bonne Terre, Mo., mill to recover a significant portion of the residual, finely divided galena. Production of a high-grade concentrate was not part of the immediate objective. Only a reasonable ratio of concentration of lead sulfide slime was sought, since the problem of upgrading by mechanical or extractive processes would be considered in the later stages of this study. The results show that, from a feed material averaging 0.20 percent lead (about 70 percent finer than 400-mesh), a recovery of up to 45 percent could be effected by flotation in rougher concentrate analyzing up to 6.5 percent Pb. These results were obtained by using larger quantities of various xanthates and sodium sulfide than used customarily in mills. Sodium sulfide, which is ordinarily detrimental to flotation of galena, was beneficial in this case.

Jan 1, 1959

By C. W. Vierrether

Tailings from the Pea Ridge iron mine contain significant amounts of apatite, which has rare-earth element values associated with it. In association with the recovery of rare-earth minerals as a secondary resource, the U.S. Bureau of Mines conducted an investigation on the recover ability of the rare-earth minerals from these tailings. The mill tailings were subjected to a phosphate flotation to separate the apatite from other constituents. More than 70-pct recovery of the rare-earth values was achieved. Based on mineralogical characterization and prior analysis of rare-earth-bearing breccia pipe material at Pea Ridge, it is proposed that processing this phosphate concentrate on a vanner table would yield up to a 95-pct recovery of the rare earths in the concentrate, with the apatite reporting to the tailings. Intensive ore microscopy studies of the original tailings to the flotation products led to the identification of monazite, xenotime, and rare-earth-enriched apatite as the major rare-earth-bearing minerals in the tailings.

Jan 1, 2010

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the Bureau of Mines studied the 350-acre Henry?s Lake Wilderness Study Area (ID-035-077) in order to evaluate its identified mineral resources. The Wilderness Study Area is located in northern Fremont County, ID, approximately 140 air miles north-northeast of Pocatello and 3 miles south of the Montana border. The Wilderness Study Area is near the north shore of Henry's Lake at the foot of the southwest-facing slope of Black Mountain. Archean hornblende gneiss, the main rock type present, crops out northeast of the Madison Range Fault, which trends northwest across the southwest corner of the Wilderness Study Area.

Jan 1, 1988

By Steven J. Page

Longwall double-drum shearers frequently have difficulty complying with the 2.0 mg/m3 dust standard and, therefore, require the use of effective dust controls. However, before dust controls can be implemented effectively, the major individual dust sources must be determined and their relative severity evaluated. The Bureau of Mines has recently developed a sampling strategy, based upon short-term gravimetric sampling, that can identify the major dust sources contributing to the shearer operator's exposure. This technique utilizes approved gravimetric sampling equipment already available to all mine operators and can be performed by two people in 2 days. Five examples, including data analysis, are discussed with respect to various cutting sequences. In addition, typical dust source contributions obtained from studies of double-drum shearer operations regularly in compliance are included. Mine operators can thereby compare their dust source evaluation results with those from these longwalls.

Jan 1, 1982

By C. W. Smith

The Bureau of Mines conducted physical and chemical beneficiation studies on three samples of waste investment casting molds to devise a method to liberate and recover zircon. Rod mill grinding, autogenous attrition grinding, and caustic leaching were liberation methods inves-tigated. Flotation, gravity separation, and caustic leaching and sizing were recovery methods investigated. Flotation techniques produced con-centrates containing up to 74.2 pct zircon with a zircon recovery of 53.4 pct. Gravity concentration produced concentrates containing up to 98.6 pct zircon; however, recovery of the zircon was only 57 pct. Caustic leaching and sizing produced concentrates containing up to 98 pct zircon with attendant recoveries of 81 pct.

Jan 1, 1985

By E. C. Tarpley, H. M. Cooper, R. F. Abernethy

The standard method of employing preliminary air-drying to determine the moisture in coal has been criticized with respect to the loss of heating value from excessive air-drying. By this method, the coal is air-dried at approximately 10-15° above room temperature with the loss in weight being less than 0.1 percent per hour, and then the residual moisture at 105°C is determined. The total moisture is calculated from these two values.

Feb 1, 1948

By James R. McVey

Tests during pillar robbing, longwall operations, and other mining activities indicate that roof-floor convergence rates can be used as an indicator of imminent roof failure. A large number of electrical-mechanical devices have been built to measure convergence as well as convergence rates, but most obstruct mine traffic and are costly and time consuming to install. The Bureau of Mines has designed and is evaluating three types of small ultrasonic units to make these measurements. The new instruments provide nonobstructing measurements up to 35 ft away. The ultrasonic transducers can be attached to a roof bolt, placed in an unsupported area (by means of a toss basket), or handheld. Total distance to the target and rate of closure are displayed digitally to 0.001 ft and 0.01 ft/min, respectively.

Jan 1, 1984

By H. R. Babitzke

The purpose of this Bureau of Mine- investigation was to develop columbium and tantalum alloys suitable or u at elevated temperatures. Columbium and tantalum were combined with tungsten, hafnium, zirconium, molybdenum, vanadium, and titanium, and the resulting alloys were evaluated with respect to workability, hardness, electrical resistivity, strength at elevated temperatures, oxidation resistance, and weldability. Cb-33Hf-10W-10Ti, Cb-20111-5Mo, and Cb-30Hf-5Mo exhibited superior high temperature properties. Cb-33Hf-10W-10Ti had tensile strength values of 44,300 psi at 1,200° C and 16,500 psi at 1,400° C, Cb-20Hf-5Mo had values of 35,700 and 20,700 psi, respectively. The corresponding values for Cb-30Hf-5Mo were 38,900 and 17,800 psi. These alloys are fabricable by conventional methods with excellent strength at temperatures up to and including 1,400° C. An oxidation rate of 7 to 21 mg/cm2/hr was observed up to 1,000° C.

Jan 1, 1967

By J. J. Drost

The feasibility of basic oxygen furnace (BOF) offgas heat recuperation by preheating scrap was investigated on a pilot plant scale by the Bureau of Mines. In this study, offgases generated during the oxygen blowing of a molten pig iron and scrap charge were passed through a static bed of shredded auto scrap. Scrap quantities varying from 100 to 180 pounds and representing from 22 to 40 percent of the 450-pound BOF metallic charge were preheated in this manner. Average scrap bed temperatures of 1,650° F for 100 pounds of scrap and 1,150° F for 180 pounds of scrap have been achieved during the blows. As compared to cold scrap used in the normal BOF practice, it was found that by preheating scrap, usage could be increased by 43 percent. The thermal energy recovered by this preheating method can account for up to 44 percent of the energy necessary to melt the scrap.

Jan 1, 1974

By John Dasher

The impetus given to mineral dressing arid chemical engineering by the war has placed many persons without previous experience in positions where they are concerned with the size of solid materials they are testing. Many good textbooks cover this field in considerable detail but are more concerned with the "why" than with the "how" For beginners and those to whom size is not of primary concern, this brief circular has been prepared. Refer-

Jan 1, 1942

By Albert E. Long

Since December 10, 1945, the Mount Weather Branch, Mining Division, Bureau of Mines, has been maintaining detailed performance and cost records on the diamond coring bits used throughout the United States by the Bureau of Mince. Figure 1 is a copy of a typical master record sheet showing the scope and type of information recorded for each bit. It is the intention of the Bureau of Mines to issue analytical reports covering the effects of diamond size and quality on the cost of core drilling in different rocks as the information on a significant number of bits used in any one type of rock is accumulated. This report is the first of such a proposed series and is based on the diamond loss and bit costs incurred in the use of 539 AX bits in coring operations on 10 different projects involving 6,097 feet of drilling in gneiss. The 10 projects were located in New York, Pennsylvania, and New Jersey (fig. 2). As a result of the information accumulated on the use of diamond-coring bits in drilling in gneiss, it has been found that the type of bit, the matrix, the percent of core recovered, and the size and quality of diamonds used have a definite effect on the cost of bits per foot drilled.

Jan 1, 1950

By F. N. Kissell, R. J. Bielicki, J. H. Perkins

A sorption apparatus for measuring the equilibrium sorption isotherm and the rate of diffusion of methane from fine-sized coal was designed and constructed. Preliminary work that used Pittsburgh and Pocahontas No. 3 coal shows that the diffusion coefficient varies with pressure and that the fracture spacing in these two coals is substantially different.

Jan 1, 1972

By R. E. Lindstrom

A study of ion-exchange resin crosslinkage and eluant flow rate, resin-bed shape, and addition of separating ions to feed stock was undertaken to determine their effect on the separation efficiency of ion-exchange on bastna-site-rare-earth elements. Results show that 12-percent divinylbenzene (DVB) crosslinkage resin is detrimental to separation efficiency at flow rates over 2 to 5 ml./min./sq. cm.; whereas, separation with 4-percent DVB crosslinkage resin is relatively unaffected by flow rates between 2 and 10 m1./min./sq.cm.

Jan 1, 1959

By C. M. Mason

The current Bureau of Mines active list of permissible explosives includes 95 brands. Twelve are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1968

By John Paul Gries

During World. War II, when the curtailment of imports led to an unprecedented demand for domestic mica, beryl, spodumene, and other pegmatite minerals, the Bureau of Mines and the Geological Survey entered upon a program designed to expedite mining of these minerals from the Black Hills area of South Dakota. The program involved napping, sampling, and drilling of many pegmatite dikes in the southern portion of the Black Hills and beneficiation conducted in the field and in the Bureau of Mines laboratories at Rapid City, S. Dak., Rolla, Mo., Salt Lake City, Utah, and College Park, Md. This report describes the occurrence and sampling of the Beecher No. 2 pegmatite, which was investigated as part of the general pegmatite study in South Dakota. Investigation of the Beecher No. 2 pegmatite was started on November 20, 1943, and terminated in the spring of 1944. During this period, the Bureau of Mines took a series of trench samples across the pegmatite at the surface for grain-count studies and chemical analyses. The Geological Survey mapped the geology of the deposit after it was exposed by trenching and stripping.

Jan 1, 1950

By Harry E. Brownlow

The United States Bureau of Mines contracted Norecol to prepare a report identifying the regulatory processes associated with metal mine development in British Columbia using the Snip Mine as a case study. The intent of this study is to assist industry and regulatory agencies in developing understanding as to differences in objectives, perspectives and operating methods. The case study will be incorporated into a larger report summarizing the comparative advantages and disadvantages of metal mine permitting in British Columbia and Alaska. The purpose of the report is to identify the development schedule and permitting process at Snip which will assist the U.S. Bureau of Mines in suggesting improvements in environmental review and permitting processes for mine developments. The report provides an abstract of the environmental assessment review processes in Canada and the Mine Development Review Process in British Columbia and provides an understanding of the linkages between policy, legislation, and environmental review.

Jan 1, 1992

By Robert C. Bates

This Bureau of Mines report converts published data on the cost of ventilating uranium mines to a common price base and analyzes these data to determine the cost per ton of uranium ore at various levels of radiation exposure control. There appears to be an exponential increase of cost as the radiation level is lowered. The 1967 base costs are extrapolated to present dollars, and some cost comparisons are given for other radiation control measures.

Jan 1, 1981

By H. Kenworthy

A zinc-pyrite ore from the Gray deposit in Jo Daviess County, Ill., was successfully concentrated on a laboratory scale. Initially, drill cuttings were submitted for separation of zinc and iron concentrates. Subsequent to mine development, a large sample of coarse ore was submitted to ascertain its amenability to sink-float treatment to produce a low-grade zinc-iron concentrate and discard a clean tailing. The samples of ore were submitted to the Rolla Metallurgical Branch by the Mining Division of the Federal-Bureau-of Mines. They were obtained during the recent war as a part of the extensive government program to increase metal production through exploration for new mineral deposits and investigation of old mineralized areas. The first sample consisted of about 3,000 pounds of drill cuttings collected, during the Bureau?s churn and diamond- drilling program. The second sample was taken at a later date, after Tri-State Zinc, Inc., had opened the deposit and commenced milling the ore. This sample consisted of a ?ton-of mill feed crushed through 2 inches and collected over a period of 3 days.

Jan 1, 1949

By Steven J. Page

Responding to the increasing concern for dust control in metal and nonmetal mining, the Bureau of Mines investigated typical dust reduction efficiencies of wet bar cutter machines as they are presently being used in salt mines. Wet bar techniques have previously been used in coal mines, achieving dust reduction efficiencies ranging from 11 to 60 pct. Two different wet bar techniques, namely, the front spray and the water trickle, have been studied as they are currently being used in two salt mines. Preliminary results show that the dust reduction efficiencies have a large variation (0 to 66 pct), as is the case for wet bars used in coal. However, whereas wet bars in coal required 3 to 4 gpm water consumption, wet bars in salt obtained similar efficiencies with only 0.1 to 0.4 gpm. The most reliable data obtained during this study show that the front spray system consistently performs at efficiencies between 41 and 66 pct, with an average of 54 pct. The results indicate that, although wet bar cutter techniques in salt mines are a relatively simple and inexpensive means of dust control with a minimum of water consumption, further investigation should be performed to fully evaluate and optimize wet bar cutter dust reduction efficiencies.

Jan 1, 1980