Search Documents

By JOEL H. SWARTZ

During a series of resistivity measurements carried out in 1929 and 1930 a number of questions arose concerning the effect of topography on the character of the curves and the depths attained , the ratio of true depth to certain radii interpreted as representing depth , etc. To answer these questions it was decided to undertake a series of experimental investigations on artificial strata . It is the purpose of the present paper to present the results of the studies thus undertaken .

Feb 1, 1931

By L. L. Oden

The U.S. Bureau of Mines and the Department of Energy (DOE), through its contractor EG&G Idaho Inc., are collaborating on a multiyear research project to evaluate the applicability of three-phase, electric arc furnace melting technology to vitrify materials simulating low-level radioactive and mixed wastes buried or stored at the Idaho National Engineering Laboratory and other DOE sites. The melter is a sealed, 1-t (1.1-st), three-phase, 800-kV?A electric arc melting furnace with 10.2-cm-(4-in?) diameter graphite electrodes, water-cooled roof and sidewalls, and four water-cooled feed tubes. A water-cooled copper fixture provides for continuous tapping of slag. An instrumented air pollution control system (APCS) with access ports for analysis and a feeder based on screw conveyors and a bucket elevator are dedicated to the facility. Test data are provided by an arc furnace analyzer and by sensors indicating feed rate; slag temperature; and temperature, pressure, and velocity in the APCS. These data are received by a data logger, digitized, and transmitted to a personal computer for storage and display. This unique waste treatment facility is available for public and private use on a cost-sharing basis.

Jan 1, 2010

By B. K. Shibler

A highly flexible laboratory-scale fluidized-bed reactor was designed, constructed, and successfully operated continuously at temperatures up to 1,300° C during an investigation of thermal methods for decomposing gypsum. This report discusses briefly the many problems encountered in developing the 10-inch-diameter reactor and describes its design and construction in sufficient detail to enable other research organizations to build a comparable unit. The reactor consists of a 10-inch-inside-diameter vertical tube which can be varied from 6 to 10 feet high; it is formed from 2-and 3-foot sections of silicon carbide pipe. The tube is surrounded by a 3-inch heating space formed by an outer 4.5-inch-thick circular wall of insulating firebrick. A cone-shaped fluidizing chamber is bolted to the bottom of the reactor. Fluidizing gas enters through the bottom of the cone, and ore is introduced by means of a screw feeder connected to an inlet located just above the gas port. A silicon carbide overflow tube of 1.25-inch inside diameter extends upward into the reactor. The depth of the bed is controlled by substituting different lengths of overflow tube. Twin dust-recovery systems, each composed of a cyclone and Fiberglas filter, are attached to two gas outlets at the top of the reactor tube. The reactor is designed for research on both exothermic and highly endothermic reactions. It can be fired externally by means of four natural gas burners that jet tangentially into the annular space at the base of the reactor. Alternatively, it can be fired internally, using a mixture of air or oxygen and natural gas as the fluidizing medium. A separate instrument panel contains flowmeters, manometers, an automatic program controller, and a multiple-point recorder for printing a record of the temperatures measured by thermocouples located at critical points in the reactor.

Jan 1, 1963

By D. G. Kesterkel

Low-melting thoriurnrbase binary alloys or metal solutions were prepared by two different techniques involving the electrolysis of ThO2 dissolved in fluoride melts. Experiments were performed at 950° to 1,250° C using electrolytes containing ThF4 and various alkali and alkaline earth fluorides. In the first method, electroreduction of ThO2 and deposition of thorium on a nickel or iron cathode formed a molten alloy that dripped off and collected on the bottom of the cell, or in a tungsten cup. An electrocodeposition technique was used to prepare thorium-base alloys or solutions containing nickel, iron, chromium, or manganese. Electrolytic reduction of the component metal oxides and simultaneous deposition of the two metals on a tungsten cathode yielded a liquid alloy product. Complementary experiments were performed on the fused fluoride electrowinning of dendritic thorium from Th02 at 1,075° to 1,200° C in which thorium crystals were recovered and arc-melted into buttons. Major contaminants were aluminum, carbon, copper, iron, oxygen, and silicon, totaling 0.2 percent.

Jan 1, 1966

By P. E. Churchward

Rhenium sources and recovery methods were investigated by the Bureau of Mines to delineate potential resources of the metal. The only significant rhenium resource appears to be about 28,000 lb of rhenium contained in the domestic annual output of approximately 20,000 tons of byproduct molybdenite concentrates from porphyry copper operations. An estimated 70 to 80 pct of this rhenium is potentially recoverable by processing the rhenium-bearing fumes and dusts obtained during conventional roasting of molybdenite concentrate. At 70 pct recovery this would amount to 19,600 lb of rhenium. A more conservative estimate by the Committee on Refractory Metals of the National Research Council (1513 is that 12,000 lb of rhenium metal could be produced annually from current production of molybdenite from porphyry copper operations in the United States. A procedure was developed in the laboratory for recovering rhenium in the form of electrolytic flake by electrowinning the metal from a solvent extraction strip solution. The procedure included (1) water leaching of molybdenite roaster flue dust, (2) selective extraction of rhenium from the leach liquor by contacting it with a kerosine solution of a quaternary amine, (3) stripping of rhenium from the loaded organic solution by a perchloric acid solution, and (4) electrodeposition of rhenium from the loaded strip liquor. Raw material for the studies was flue dust containing 0.48 pct Re, 35 pct Mo, and 23 pct S in sulfide and sulfate form, and small amounts of numerous metallic impurities. Water leaching dissolved 85 pct of the Re and yielded a solution that was 13 in sulfuric acid and contained, 1 g/l Re and 16 g/l Mo. The solvent extraction strip solution that was electrolyzed for rhenium deposition was 1 molar in perchloric acid and 1 molar in ammonium sulfate and contained 13 g/l Re and 0.01 g/l Mo.

Jan 1, 1963

By B. R. Eichbaum

To develop technology to assure an ample supply of zinc and to reduce environmental pollution, the U.S. Bureau of Mines investigated alternatives to the roast-leach process for treating complex sulfide concentrates. Previous studies proved that low-grade zinc sulfide (ZnS) concentrates could be leached using chlorine-oxygen to produce zinc chloride (ZnCI2). The process involves high energy requirements for evaporating the pregnant solution to produce anhydrous ZnCl2 needed for electrolytic cell feed. An efficient hydrometallurgical process would facilitate treatment of lower grade ores than can be used in conventional processing and would render roasting unnecessary. An alternative method was devised for recovering ZnCl2 from solution. Zinc diammine chloride [Zn(NH3)2CI2] was precipitated from solution by adding ammonium chloride (NH4CI) and sparging with ammonia (NH3) to a pH of 6 to 7.5. The spent solution was treated with calcium hydroxide [Ca(OH)21 at 60° to 80° C for 1 to 4 h to remove remaining zinc and NH3. The Zn(NH3)2CI2 was heated to 300° to 400° C to remove NH3 and produce anhydrous ZnCI2. A possible flowsheet was devised and is included.

Jan 1, 1991

By R. D. Currie

Haulage accidents in the anthracite region cause fewer fatal and lost-time accidents per million man-hours than similar accidents in bituminous mines, a fact that may be accounted for in several ways, but primarily because haulage, in a large part of the region, is restricted to haulage crews operating only on the gangways where most of the miners seldom come in contact with movement or handling of cars and locomotives. Generally in underground mines the number of men injured compared with the number killed is greater for haulage than for roof-fall accidents, while the number of men killed by haulage is second only to the number killed by roof falls.

Jan 1, 1939

By Elaine T. Cullen

Underground mining, like many high-risk industries, is facing a crisis in the near future. This industry has traditionally relied on a master-apprentice relationship to train new workers, but experienced miners are retiring in large numbers, leaving few "masters" to properly train their replacements. With a recent resurgence in mining, many new miners are entering the workforce each day. The rise in the number of inexperienced workers has implications for worker safety in an industry in which one mistake can blow up the entire workplace. The explosion in the Darby Mine in May 2006 that killed five miners illustrates what can happen in hazardous environments such as underground mines. The Health Communications Team at the National Institute for Occupational Safety and Health Spokane Research Laboratory was asked to address this problem by developing new training and safety awareness materials to promote safe flame cutting and welding practices. This article describes how occupational ethnographic techniques provided insights needed for "new product development." The result of this work was a national initiative to raise awareness and to protect underground coal miners from the dangers of flame cutting and welding in an environment filled with solid fuel and methane (natural gas). Although this project was initially designed for the mining industry, the approach and lessons learned are applicable to any high-risk industry and should be of interest to other social marketing or occupational safety and health professionals.

Jan 1, 2009

By J. E. Chilton

Underground miners may be exposed to hazardous quantities of toxic gases, such as carbon monoxide (CO), generated from mine fires or explosions. Every underground miner is required to carry a filter self-rescuer (FSR), which when operated will remove CO from the miner's breathing air. In addition, every underground miner must have a self-contained self-rescuer (SCSR) near the worksite that will supply breathing oxygen. In many situations, miners do not know when to don either rescuer since they do not know if there is a fire in the mine, nor do they carry instrumentation necessary for the detection of the toxic, colorless, and odorless fire product CO. If each miner carried a personal CO alarm, which would respond to high concentrations of CO, the miner would then be alerted when to don either the FSR or SCSR and exit the mine. A prototype personal miner's CO alarm called PEMCOAL was developed by the U.S. Bureau of Mines. The PEMCOAL unit is small enough to be carried on a miner's belt, has a flash lamp visual alarm, requires no calibration for use, and uses a chemical sensor that changes color by reaction with trace quantities of CO. The chemical sensor was tested at concentrations of CO from 10 to 1,000 ppm, at temperatures from 5° to 40° C, and with several potential mine gas interferents. The PEMCOAL alarm times were sufficiently fast to warn miners before they are exposed to hazardous quantities of CO.

Jan 1, 1989

By BUREAU OF MINES

This paper is a revision of Reports of Investigations , Serial 2541 , which was published in November , 1923 , for the benefit of State mining inspectors , safety engineers of mining companies , and others interested in electrical safety inspection in mines . It presents the important points that should be watched by inspectors and briefly reviews the work of the Bureau of Mines in testing of electrical apparatus and equipment to determine their permissibility for use in gassy coal mines .

Jan 1, 1929

By R. E. Perry

To develop new or improved flotation methods for beneficiating low-grade red iron ores, the Bureau made many bench scale and continuous anionic flotation tests on ferruginous sandstones and calcareous iron ores from the north-eastern part of the Birmingham, Ala., iron district. The ores contained about 21 to 36 percent iron, a to 11 percent lime, and 22 to 64 percent silica. Production of iron concentrates containing 48 to 52 percent iron was technically feasible in batch tests, and the iron recoveries ranged from 85 to 92 percent. In continuous tests 49 to 51 percent iron products were obtained with 80 to 90 percent recovery.

Jan 1, 1962

By Donald O. Rausch, Robert H. Merrill, David W. Wisecarver, S. Jackson Hubbard

Results are reported for stress - relief borehole - deformation measurements made in three underground openings near open - pit mines in the Ruth mining district , Nevada . A total of 134 deformation measurements were made in 8 boreholes . These measurements determined the regional stresses in the horizons above , below, and at the elevation of nearby open - pit mine floors ; knowledge of these stress conditions is considered essential information relative to certain aspects in the designing of stable pit slopes . The determinations indicate that the stresses in the district are due to the gravitational load of the overburden in a confined stress field .

Jan 1, 1964

By E. C. Strycula

Solid-state equipment offers a number of potential advantages in the coal mining industry. These advantages can only be realized, however, through careful and judicious design of the control and protection circuitry. Problems relating to the interaction of solid-state equipment on the electrical system and the special design considerations which apply to solid-state circuitry are examined. Design guidelines are provided for solid-state applications in the areas of: (a) equipment operated from a DC trolley wire, (b) drive systems for surface mining equipment, (c) AC motor starters, and (d) electromagnetic interference.

Jan 1, 1981

A revolutionary development in blasting materials has occurred in recent years. Ammonium nitrate, sensitized by the addition of a small percentage of No. (class) 2 diesel fuel or other suitable petroleum product, has been adopted as a low-cost, efficient blasting agent2 in a wide variety of mining, quarrying, and heavy construction operations. Moreover, the ready availability of the component supplies throughout the Nation, together with the ease of formulating them into effective blasting agents, has made it possible for the blaster himself to prepare the mixes at the site of use. Recently, most established explosives manufacturers have begun supplying premixed AN-FO (ammonium nitrate-fuel oil) or a comparable product to various mining operations. However, many individuals and small business establishments are marketing premixed products prepared in facilities that are often poorly constructed and poorly located. Although these blasting agents have partly or wholly displaced explosives such as dynamites in many applications, there are some blasting operations in which the fuel-sensitized ammonium nitrate agents do not appear to be well adapted. As long as the hazards they present are clearly understood and respected, ammonium nitrate-based blasting agents have important safety characteristics when prepared under competent factory control or field-mixed under equivalent close control. This publication attempts to summarize the knowledge of those hazards and to incorporate practical ways to cope with them.

Jan 1, 1963

The Bureau of Mines conducted a field study to assess the performance of various chain pillar configurations in terms of gate road entry sta-bility. Vibrating wire stressmeters (VWS's) were installed in four consecutive gate road chain pillars. Field data collected during panel retreat were analyzed to gain a better understanding of the mechanics of vertical load redistribution in gate road chain pillars as it relates to ground control problems. Several different pillar configurations were investigated including abutment-yield and yield-abutment-yield designs. VWS data indicate that average pillar loads were lower and appeared abutment-yield pillar arrangement was utilized. port the occurrence of severe roof and pillar to stabilize when an Data analyses also supdeterioration that was visually observed in the tailgate entries during panel extraction.

Jan 1, 1988

By John R. Shattuck

The Shasta and California Iron-ore deposits are 14 miles northeast of Redding, Shasta County, Calif.; and since 1907 have produced more than 300,000 short tons of exceptionally pure iron ore. Although some ore was mined and smelted from 1907 through the First. World War, most of it has been produced from 1942 through 1945 for use in making heavy ship ballast and concrete anchorages for mines. Irregular masses of magnetite, ranging from lumps of a few tons to pods containing about 25,000 tons, occur associated with skarn near the contact between the McCloud limestone and a younger granitic intrusive. Some of the deposits are low-grade, whereas others are nearly pure magnetite. Selective mining and hand sorting are necessary to produce a high-grade product. Investigation of these deposits by the Bureau of Mines included 2,910 feet of diamond drilling, some surface sampling of the principal mineralized zone and beneficiation tests. Resulting factual data are given in the body of this report.

Jan 1, 1948

By Roy E. Peterson

The Bureau of Mines conducted an investigation to produce metallized pellets from domestic iron ore superconcentrates using lignite and subbituminous coal as reductants. Feed materials for the metallizing process consisted of commercially indurated iron oxide pellets and green pellets prepared from upgraded domestic concentrates with graphite or limestone as internal additives. Durability of the green pellets during metallization was investigated in tests conducted in a 7-inch-ID rotating drum furnace. Test results indicated that the major cause of pellet disintegration with the concentrates used was the tumbling action during reduction rather than forces generated within the pellets. In larger scale tests made in a 34-inch-ID by 35-foot-long kiln, the previously indurated pellets were metallized with lignite at 1,030° C with little disintegration. A 96-percent level of metallization was obtained in pellets having an average compressive strength of 420 lb. In subsequent, similar tests using green pellets containing graphite or limestone, pellet disintegration was more severe, with 10 to 40 percent of the feed being lost as dust. The surviving pellets had metallizations ranging from 88.3 to 94.4 percent and compressive strengths ranging from 60 to 68 lb.

Jan 1, 1976

By Paul M. Tyler

In 1939, American industry got, off to a poor start, slowed down further during the first quarter, quickened after May, speeded up still more when war broke out again in Europe, and ended the year at a pace close to an all-time record. The average index of general business activity for the entire year (105) was well ahead of that for 1938 (86), failed to equal that of 1937 (110), and fell behind the average for 1929 (119) by a wide margin. (Federal Reserve Bank yearly indexes in parentheses).

Jan 1, 1940

By R. H. Dickson

This paper, which describes the milling practice of the Verde Central Mines, Inc., is one of a series on milling methods and costs being prepared by the United States Bureau of Mines. GENERAL DESCRIPTION The Verde Central concentrator is located in Walnut Gulch, about 1 mile west of Jerome, Ariz., and on the Jerome-Prescott highway. It is about 1,000 feet distant from the main shaft of the Verde Central mine and treats ore from this mine only. The mill is connected with the main shaft of the mine by a 24-inch gave railway, over which the ore is hauled in 5-cubic yard capacity, rocker, side-dump cars, by a 3-ton Brookville gasoline locomotive.

Jan 1, 1931

By Thomas M. Barczak

This Bureau of Mines report describes research on developing technology to utilize shields as roof load monitors. Three-dimensional equations of static quilibrium are presented for a generic two-legged long-wall shield. The equations are presented in the most general form, assuming a force and moment vector at each reaction by rigid-body analysis of the shield mechanics. The resulting system of equations was found to be indeterminate to a very high degree. A three-dimensional solution to measurement of the resultant reaction on the canopy by the strata activity and shield response required the elimination of several forces or moments that were thought to be nonparticipating or to not significantly affect overall shield mechanics. Required measurements for solution of the equilibrium equations were leg, canopy capsule, and lemniscate link forces. Two-dimensional analysis, which considered forces acting only in the roof-to-floor and face-to-waste plane, was also provided by reduction of the three-dimensional equations~

Jan 1, 1987