Search Documents

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006

By G. L. Mowrey, S. D. Maksimovic

An important element of the U.S. Bureau of Mines (USBM) mining research program is the development and evaluation of reliable coal interface detection (CID) systems. Commercially available CID sensors based on natural gamma radiation (NGR) are only applicable if the immediate roof is composed of shaley material. The USBM has made numerous underground and laboratory measurements using several NGR systems approved for installation on mining machines by the Mine Safety and Health Administration. In addition, two small handheld NGR instruments were used to make comparative measurements. Underground NGR measurements in 10 different coal seams, potassium-uranium-thorium radiometric analyses on samples from 16 seams, and chemical analyses of coal and rock for correlation with NGR counts were made. Laboratory test results on the effect of air gap and sample thickness, size, and weight on the NGR measurements, as well as general results of the various NGR systems, are discussed.

Jan 1, 1995

By G. G. Morgis

In carrying out the provisions as set forth by an Act of Congress (36 Stat. 369) approved May 16, 1910, effective July 1, 1910, and the amended Act of February 25, 1913, (37 Stat. 681), the Bureau of Mines, among other activities, conducts inquiries and scientific and technologic investigations concerning mining with a view to improving health conditions and increasing safety and disseminates the general information gained by these studies. Through the medium of these publications, the causes as well as the methods that have been found most satisfactory in combating undesirable conditions are brought to the attention of the mining industry. This bulletin describes health and safety reports that have been published for the period July 1, 1955, through June 30, 1961. Technical Paper 705 issued in 1948 contains a listing of all Bureau of Mines publications dealing with health and safety in the mineral and allied industries from 1910 through 1946; Bulletin 558 contains a bibliography of such reports that were issued from January 1947 through June 1955.

Jan 1, 1962

By L. Yuan, A. C. Smith

To provide insights for the optimization of ventilation systems for U.S. underground coal mines facing both methane control and spontaneous combustion issues, a computational fluid dynamics (CFD) study was conducted to model the potential for spontaneous heating in longwall gob areas. A two longwall panel district using a bleeder ventilation system with a stationary longwall face was simulated. The permeability and porosity profiles for the longwall gob were generated from a geotechnical model and were used as inputs for the CFD modeling. In this study, the effect of methane emissions from the mined coal seam, including the longwall face and overlying rider seam reservoirs on the gob gas distribution was considered. The spontaneous heating is modeled as the low-temperature oxidation of coal in the gob using kinetic data obtained from previous laboratory-scale spontaneous-combustion studies. Unsteady state simulations were conducted, and the effects of the coal’s apparent activation energy and reaction surface area on the spontaneous heating process were also examined.1

By R. H. Grau, S. B. Robertson, R. B. Krog, T. P. Mucho

Due to the difficulties of ventilating large opening stone mines, the effective dilution of diesel particulate matter and noxious gases has often been problematic. Since stone mines have large openings that develop low air resistances, and propeller fans are designed for low pressure-high volume applications, main mine propeller fans may be a feasible option for ventilating underground stone mines. This paper describes the results of a case study where researchers from the National Institute for Occupational Safety and Health have demonstrated that significant increases in total mine airflow can be achieved and the ventilation improved in a large-opening stone mine by replacing an axial-vane mine fan with two 12-ft diameter propeller fans and adding a line of stoppings. In this study, the use of the propeller fans more than doubled the air quantity from 300,000 cfm to 750,000 cfm, while operating at 50 horsepower less than the original axial-vane fan.

By Christopher Mark, Gregory M. Molinda, Timothy M. Barton

The Coal Mine Roof Rating (CMRR) was first presented at this Conference nine years ago. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, and extended cut evaluation. It has also become truly international, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. The purpose of this paper is to bring the mining community up to date with recent improvements and applications of the CMRR. The most important new development is a streamlined process for determining the CMRR from exploratory drill core. Just three types of information are now required: •Fracture spacing (or RQD) •Uniaxial compressive strength (or axial Point Load Testing) •Diametral Point Load Testing The moisture sensitivity adjustment has also been changed, and new research has related the immersion test to slake durability. Most recently, the CMRR has been implemented in a computer program, which can be obtained from NIOSH free of charge. The program facilitates calculation of the CMRR from either underground or drill core data. Values from many locations can be saved in a single file, and an interface with Autocad allows CMRR contour plots to be integrated into mine planning.

By R. Karl Zipf, Suresh Bhatt

Highwall mining is an important coal mining method. It appears that upwards of 60 highwall miners are presently in operation, and they may account for approximately 4% of total U.S. coal production. A review of the Mines Safety and Health Administration (MSHA) data over the 20 year period from 1983 to 2002 identified 9 fatalities attributable to auger and highwall mining of which inadequate ground control accounted for 1/3. In the past 5 years, 1 fatality occurred in highwall mining. Estimates of the manpower requirements in highwall mining suggest that its fatality rate is essentially the same as for surface coal mining, thus highwall mining appears to be a very safe modern mining method. Highwall stability is the major ground control related safety concern, and operators are required to develop and follow an appropriate highwall mining ground control plan. The plans usually specify the following geotechnical parameters: hole width, maximum hole depth, maximum overburden depth, seam thickness, web pillar width, barrier pillar width and number of holes between barriers. Calculated web pillar stability factor exceeded 1.3 for most designs evaluated. This study examined records from 5,289 highwall miner holes with a total completed footage of about 2,560,000 feet to understand the reasons for early pull out. Average lost footage is typically about 20% of planned footage. Only 35% of the holes reached planned depth, and 20% were short due to rockfalls. Water and adverse geology accounted for 15% of the losses. Mechanical/electrical problems, guidance, and slope stability problems accounted for the remaining 30%. Web pillar stability factor for these holes also exceeded 1.3 in 95% of cases. Best practices to avoid trapped miners include: avoid mining in stream valleys, avoid mining near outside corners, careful alignment of each hole and the use of an onboard guidance system. Several issues in highwall mining ground control require further investigation including highwall mining through old auger workings, highwall mining near old underground mines, multiple-seam and multiple lift highwall mining and finally the size and frequency of barrier pillars.

By D. Harrington

"One of the underlying reasons for the establishment of the United States Bureau of Mines was the desire to promote greater safety in the mining and allied industries. Safety continues to be an important feature in the work of the bureau, and during the fiscal year 1929-30 the Bureau of Mines allotted $387,510 to the safety division out of a total appropriation of $2,249,670 (other than for helium).The safety division personnel consists of 22 engineers, 2 mine safety commissioners, 3 senior foreman miners, 18 foreman miners, 16 first-aid miners, 16 clerks, 10 cooks, and 3 laborers, a total of 90 persons. These safety workers are distributed through the 10 districts into which the United States has been divided for administration purposes. During the year 3 engineers, 1 senior foreman miner, 4 foreman miners, and 4 first-aid miners left the service. In general these men left the service to take up more lucrative positions.The 10 all-steel mine-rescue cars have headquarters as follows: Car 1, Reno, Nev.; Car 2, Raton, N. Mex.; Car 3, Pittsburgh, Pa.; Car 4, Terre Haute, Ind.; Car 5, Pineville, Ky.; Car 6, Pittsburg, Kans.; Car 7, Huntington, W. Va.; Car 8, Duluth, Minn.; Car 9, Butte, Mont.; Car 10, Des Moines, Iowa. There is also a mine-rescue car with headquarters at Juneau, Alaska. In addition, there have been established 11 mine rescue stations as follows: Birmingham, Ala.; Berkeley, Calif.; Seattle, Wash.; Evansville, Ind.; Jellico, Tenn.; McAlester, Okla.; Norton, Va.; Vincennes, Ind.; Wilkes Barre, Pa.; Salt, Lake City, Utah; and Pittsburgh, Pa.Every mine-rescue car and station is fully supplied with equipment and devices for use in case of mine fire or explosion, and at each station is an up-to-date automobile truck. At time of amine disaster the bureau's forces are immediately placed at the disposal of the authorities, State or company, with a view to giving such assistance as may be desired or available.The activities of the safety division at ordinary times are directed largely to securing and disseminating data on safety in mining. Among the numerous studies made, or being made, concerning safety and health in mining are those in connection with the causes and methods of prevention of mine explosions, explosibility of dust and gases, explosives and blasting, haulage, electricity, falls of persons or material, ventilation, dusts, high temperatures, timbering, lighting, machinery, and in fact practically anything which results or may result in acci¬dents of any kind in or around mines."

Nov 1, 1930

By Zsuzsanna Zborovszky

[Certain chapters of the tentative document entitled, "Test Requirements for instruments & Apparatus to be Considered for MESA Intrinsically Safe Certification" are evaluated and supporting data are presented on certain key issues with the purpose of helping the regulatory agency in improving the above document. The subjects discussed in detail are: hot wire ignition with W and BeCu wires; the most sensitive methane-air :and propane air ratio; the ignition limits for inductive-resistive circuits in 8.3°; methane-air mixtures in the 24-OV, 100 mH-2 [ ]H range, the resistive ignition limit as a special case when L ? 0; the capacitive-resistive ignition limit representing a four ,dimensional problem is analyzed and discussed in general and the variation of the ignition limit using Vo and/or r2 as a parameter are determined experimentally. The ignition limit is also determined for the [r1 ,~ r2] = 0 case ("capacitor alone") and for the most dangerous capacitive resistive circuit combination. The ignition limits are below the limits proposed in the document. A survey of the different factors influencing the ignition is made as to their suitability to provide a constant safety factor. It is shown that a constant safety factor cannot be achieved. The best method for applying a safety factor appears to be the increase of initial pressure or use of other gas mixture. The revision of the safety factor concept and ignition limit curves is recommended.]

Jan 1, 1980

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

By E. M. Cohn

The literature dealing with the electrical conductivity of solid dielectrics, including all its aspects and its relationships to other physical properties of these materials, is extensive and scattered in many books, phamphlets, and periodicals. It is believed that most of the important contributions to this field up to October 1943 have been listed and abstracted in this circular. Also included are some general references on static electricity. Methods of removing static charges are described; methods of and conditions for measurements of resistivity are discussed; equations for the calculation of resistivity are given; and methods of resistance measurements in Situ are reviewed. Data on the variations of resistivity with changing conditions as well as explanations for them have been collected, and three tables showing the resistivity of various dielectrics at different humidities are included. The appendix contains a short development of the mathematical formulation of the charging and discharging currents due to interfacial polarisation. INTRODUCTION Methods for Removing Static Electricity Of the various means employed for preventing or removing accumulations of static electricity in industrial processes, grounding is the most common and most generally effective. It is a precaution readily applied to stationary machines anti may often be utilized to good advantage to rid persons and portable equipment of an acquired charge. There are many situations, however, in which direct low-resistance grounding cannot be used, either because the charged bodies are insulators or are inaccessible, or because contact to a ground lead might give rise to a hazardous spark. If the charged body is a conductor, contact made to a neighboring conductor, even though the latter be insulated from ground and of relatively small capacitance, may also result in the occurrence of an incendive spark. In such instances, static electricity can sometimes be removed most satisfactorily by means of strong atmospheric ionization produced by radioactive material, X-rays, ultraviolet light, or A. C. high-voltage brush discharge. Where no danger exists from flammable

Jan 1, 1944

By G. J. Colaizzi

The Bureau of Mines, at the request of local authorities in Rock Springs, Wyo., investigated and conducted through contracts a multistage program of exploratory drilling and pumped-slurry backfilling of 15 areas of potential subsidence in abandoned mine workings underneath that community. Initially, the Bureau in 1969 had recommended a program of gravity blind flushing of some of the inaccessible mine voids, and in 1970 a new technique, the pumped-slurry injection process, was tested for the first time in a site adjacent to the city's area of severe surface subsidence. Success of this initial testing program, and of a large-scale project in Scranton, Pa., led to further large- scale projects, funded by Congress, that resulted in the successful back- filling not only of all 15 target areas of potential subsidence in Rock Springs, but also of several areas in other States. Total cost of the projects in Rock Springs, including the original pumped-slurry test, was $3,243,993. A total of about 923,000 tons of sand was injected hydraulically into mine voids, rendering 178 acres of residential and central-downtown areas of Rock Springs less susceptible to subsidence damage. The pumped-slurry method was proved to be much superior to the gravity blind flushing method in term of the amount of solids that could be injected underground through a single borehole. However, there are special conditions that make this technique more or less applicable in different areas or underground configurations, as noted in the report's conclusions.

Jan 1, 1980

By R. K. Linn

The New Idria Mining and Chemical Co. owns and operates the New Idria mine in southern San Benito County, Calif. During 1957-59, the New Idria mine was the largest producer of mercury in the United States and its alltime production of over a half-million flasks was exceeded only by one mine. It is one of the oldest and most consistent producers in California. With the exception of 1921-22, the mine has an annual production of mercury dating back to 1854. This paper by the Federal Bureau of Mines describes the exploration, development, mining, and furnacing of mercury ore at the New Idria mine. Figure 1 is a view of the furnace plant of the New Idria mine. The purpose of this report is to promote the development and conservation of our mineral resources by dissemination of technological information on mining and processing procedures, and related practices at operating mines.

Jan 1, 1961

By Floyd D. Varley, C. M. K. Boldt

Toolbox training is often described as short, informal training conducted at a worksite by technically competent persons for the benefit of a work team. The key feature of toolbox training is the focus on a work team and what is important to that group in its workplace. Toolbox training conducted by peers can connect miners and establish the feeling that the hazard is a real threat to them. This feeling can bridge the gap between delivery of a safety message and behavioral changes that can prevent an accident. Toolbox training is a popular form of "maintenance" training that should not be used to teach a new skill. The 10- or 15-minute toolbox session is simply too short a time to teach or learn a new skill and test for skill development. However, the toolbox format is an excellent way to inform workers of changes in workplace rules, conditions, or hazards by bringing the discussion of change to the level of the work group and suggesting how a change will affect the way workers perform their jobs. Toolbox training should be structured to address a very specific hazard. That is, the hazard source should be identified and the effect of the hazard on the worker described. The temptation to discuss a safety subject in broad terms will result in an equally vague result. For instance, discussing "equipment guards" is inappropriate for a 15-minute training session. There simply is not enough time to cover all the hazards and their remedies. A more appropriate topic would be "placing guards on a conveyor return roller" or "hazards of cleaning a conveyor return roller." Each topic is concise enough to allow the trainer time to define a particular threat to the safety of miners and discuss ways to defend against that threat. The clearest way to a safe workplace is to identify hazards methodically and eliminate them. This cannot be done with sweeping, generalized training. Some best practices that will protect a worker from the hazard should be presented, and the hazard should be located at the specific worksite. Toolbox training is an opportunity for the work team to participate in learning and share experiences and knowledge, often through storytelling. Storytelling is an ancient form of passing along information in an entertaining way. It is entertaining because it draws the listener in with imagination and creativity. Stories told within work groups are a way for miners to exchange experiences in which they made mistakes that resulted in an accident or a near-miss and learned a valuable lesson. Thus, co-workers can learn from others without the pain or fear that accompanied the storyteller's learning path. To encourage these shared experiences, the people in the group must be comfortable with one another. Participation doesn't stop with listening to a near-miss story or informing the group of an unsafe work practice. Participation by sharing experiences, knowledge, and skills should lead toward action in changing the unsafe tool, practice, or machine (Wallerstein, 1992). This power to change is called empowerment. Empowered workers use toolbox training sessions to discuss a problem; direct their own knowledge, experience, and talents in the context of their work environment to solve the problem; and put into practice what they have learned by sharing (Baker, 1992). A worker is much more likely to implement changes they have contributed to creating than changes forced upon them. Toolbox training functions best when the group size is small (under 20) and composed of workers with similar job functions. While combining all workers on a shift or multiple shifts may be convenient, the level of participation will drop dramatically as group size increases and participants are less connected. Similarly, when the work group participants are from different job functions, keeping the materials relevant to the individual becomes more difficult. The role of management in the toolbox training system is to communicate among various groups so that all groups at a mine site are hearing the same message. In very small operations, combining work groups can be productive if the trainer can promote open discussions and lead the group to solutions that address the needs of all and not let one group or individual dominate the discussion. WHY USE NARRATIVE METHODS An effective communications tool is to use stories as a means of describing a hazard and its consequences. Historically, using stories to transfer knowledge between individuals of the same and different generations is well established. All good stories share the same elements required to communicate safety principles. Stories require a setting (the part of the workplace), a plot (the circumstances that lead to a hazard), the solution (best practices), the lesson (what can happen), and the result (what will be done to prevent the hazard) (Dennehy, 1999).

Jan 1, 2002

By Pedro Lilienfeld

This report describes the development, design, fabrication and testing of a port-able, battery-operated, light scattering monitor (henceforth to be designated as ILSDM) for the rapid measurement of the concentration of respirable dust in mining environments. This instrument incorporates state-of-the-art design characteristics and makes use of advanced solid-state components both for light emission as well as for its detection. The use of a pulsed light source combined with synchronous signal detection minimizes drift problems and optimizes the sensitivity of the measurement. Simplicity of operation, reliability and ruggedness, light weight as well as improved performance were salient objectives of this instrument development program. Continuous clean-air flow screening of all critical optical surfaces, and optimized optical detection and electronic signal processing design resulted in about a hundred-fold decrease of noise and drift with respect to precursor instruments. Equivalent mass concentration measurements 88 low as 10 micrograms per cubic meter can be routinely performed with time constants of about 2 second.

Jan 1, 1979

By C. A. Geffen

This report, sponsored by the U. S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the com¬ponent operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

By George S. Rice

[This paper gives the details of tests to determine the design of stoppings capable of withstanding a pressure, applied to either side, of 50 pounds per square inch,6 as required by section 104 (a) of the Operating Regulations to Govern Coal-Mining Methods on Leased Lands on the Public Domain, issued in 1921 and quoted oil page 3. The regulations stipulated that the design for such stoppings must lie approved by the United States Bureau of Standards. The engineers of that organization felt that knowledge of the strength of such structures with respect to the effect of explosion pressure in comparison with static pressure and the strength of the walls which furnish the abutments was insufficient to justify drafting specifications; therefore, tests were needed to give information upon which a rational system of design could be based. A study was then begun; and several series of tests, made by the United States Bureau of Mines and the United States Bureau of Standards in cooperation, grave information upon which are based the detailed specifications offered in a later section. Slabs representing concrete stoppings, with and without reinforcement, were tested at the Bureau of Standards in Washington D. C.; afterwards, full-scale stoppings were tested at the Bureau of Mines Experimental mine near Pittsburgh. It was assumed that in most coal mines the strength of the floor and roof could not be relied on, but dependence must be placed upon the strength of the coal ribs. The tests developed that the maximum strength of an unreinforced concrete stopping was obtained when it acted as a flat arch buttressed against the coil ribs; but its ultimate strength depended upon the resistance to movement offered by the coal strata against which its ends were restrained or buttressed.]

Jan 1, 1931

By A. C. Johnson

This circular is one of a series published by the Bureau of Mines describing mining and beneficiation methods and costs at various mining operations throughout the United States. Inclusion of the Abbott mine in this series is of particular interest, as the complex geology and the character of the deposits make their exploitation a unique operation. The mine operates on a high-cost, comparatively small-scale basis, and only the persistence of an aggressive management has enabled it to maintain its rank among the major mercury producers of California. Rising costs and decreasing metal prices, which continuously threaten the low profit margin, are reflected in increased efficiency of operation. This report summarizes past operations and describes, in detail, the geology and ore deposits; exploration and mining methods; and furnacing and condensing operations. It covers the entire operation from initial exploration to the actual production of mercury. Comparative production costs for 1944 and 1958 are of special interest.

Jan 1, 1962

YOUR mom was right …count to 10. Most workers today report that they find their jobs stressful. Miners, in particular, are faced with hazardous and changing environments. Every shift provides different conditions and challenges. Coping with stress is an important tool to maintain your physical and mental health. Now, back to mom. Studies on stress tell us that shifting your focus away from what is causing your stress increases your ability to cope. Counting to 10 is one method. Science proves mom right. The stress response We are born with the stress response, which is a survival instinct, sometimes called the "fight or flight" response. When approached by a tiger in the jungle, our ancestors would perceive danger and prepare to fight or run. The body prepares for the fight or flight response in a number of ways. The bloodstream brings extra glucose and oxygen (fuel) to the heart, the sense of pain is dulled, and memory and thinking improve. The pupils dilate for better vision and the lungs take in more oxygen, while heart rate and blood pressure increase. Body hairs become erect, as puffed-out hair makes an animal look bigger and more dangerous. Once the perceived danger is gone - we have run fast enough to get away from the tiger or won the fight - the body returns to normal functions. Unfortunately, civilization gives us too many opportunities to experience this response. If activated too often, it can create wear and tear on the body, which may lead to injury and illness. Chronic and traumatic stress There are two key types of stress: chronic stress and traumatic stress. Both types can cause both physical and psychological symptoms. Chronic stress builds up from the day-to-day hassles. Traumatic stress results from a traumatic event such as a natural disaster, a mine disaster, or the sudden death of a loved one. Chronic stress is associated with an increased risk of a number of health problems including heart disease, depression, back pain, and carpal tunnel syndrome. Traumatic stress may lead to post- traumatic stress disorder (PTSD), Miners may experience both chronic and traumatic stress in their work.

By Ruth F. Brinkley

This circular describes the activities and publications of the Bureau of Mines, Explosives Research Laboratory4 for the fiscal year 1960 (July 1, 1959 -June 30, 1960). Part 1 describes briefly the principal projects that were active during the report period, and presents some data not scheduled for publication elsewhere in the near future. Certain of the results are only preliminary and should be regarded as tentative, pending the findings of the completed investigation. Publications that appeared during the report period are listed and described briefly in part 2. In general, the research activities reported in these publications antedate fiscal year 1960. The published material relating to activities that are still current is indicated by references in part 1.

Jan 1, 1962