Search Documents

By K. Thirumalai

This study forms a part of Bureau of Mines continuing research on thermal fragmentation of rocks. The potential of internal heating techniques for rock fragmentation is discussed. A concept of rock fragmentation with rapid inter¬nal heating of a localized inner volume of rock is advanced The energy required for rock fragmentation is made available by creating a required vol¬ume of localized heating. The fragmentation of rock using the proposed method is analyzed and qualitatively compared with the results of experiments with Charcoal granite, Dresser basalt, and Sioux Quartzite. High frequency dielec¬tric heating below 100 MHz is used in the study as an example to examine the working of the concept. The selection of operating conditions for the experi¬mental heating is explained. Fragmentation of Charcoal granite and Dresser basalt test rock blocks is achieved for localized heating below 550° C. The heated volume required for fragmentation is observed to be less than 2 percent of the test block volume and the electrical energy consumption is in the order of 3.5 to 6 5 kwhr/m3 The method offers a possibility for in situ fragmenta¬tion of rocks, favorable for internal heating. The method is highly dependent on rock properties governing internal heat generation The efficiency of dielectric heating in the experimental study is observed to increase with increasing dielectric loss of the rock material, ranging from about 10 percent in Sioux. Quartzite to about 50 percent in Dresses basalt

Jan 1, 1970

By William H. Pomroy

Fire on surface mining equipment is a serious hazard to life and property. The Bureau of Mines, through a program of contract and in-house research, has developed and in-mine demonstrated reasonably priced, reliable automatic fire protection systems to deal with this problem. This report reviews the development and subsequent testing of systems for haulage trucks, front end loaders, coal augers, dozers, drills, and shovels. A variety of fire sensors, extinguishing agents, and control systems arc discussed in the context of mine equipment designs and operating environments

Jan 1, 1980

By James A. Brierley

Wastewater from uranium mines in the Ambrosia Lake district near. Grants, New Mexico, U.S.A., contains uranium, selenium, radium, and molybdenum. The Kerr-McGee Corporation has a novel treatment process for waters from two mines, sections 35 and 36, to reduce the concentrations of the trace contaminants. Particulates are settled by ponding, and the waters are passed through an ion exchange resin to remove uranium; barium chloride is added to precipitate sulfate and radium from the mine waters. The mine waters are subsequently passed through three consecutive algae ponds prior to discharge. Water, sediment and biological samples were collected over a 4-year period and analyzed to assess the role of biological agents in removal of inorganic trace contaminants from the mine waters.

Jan 1, 1981

By Robert E. Johnson

1962 was the second year of recovery from the mild 1960-61 recession. The year-to-year gain in constant dollar gross national product, our most comprehensive measure of the country's economic performance, was 6.0 percent (from $447.7 billion in 1961 to $474.8 billion in 1962). The unemployment rate declined from 6.7 percent to 5.6 percent. Although it was a good year, there were still unused resources of labor and capital which implied that the economy was operating below its potential. The year-to-year change in the Federal Reserve Board (FRB) index of industrial production of 7.6 percent masked the fact that more than one-third of the growth took place within 196L The monthly index rose only 4.8 percent during 1962, from 114.3 in January to 117.8 in September. The fact that the economy as shown by the industrial index, rose rapidly in the first half of the year only to remain on a plateau of 119-120 during the second half, led some people to fear an imminent downward turn. This did not occur. Neither production nor consumption of mineral fuels advanced as fast as the total economy. But consumption showed more gain than production, 5 percent compared with somewhat less than 4 percent. Production of both crude oil and natural gas reached new highs while bituminous coal production was the highest in 5 years.

Jan 1, 1963

By Robert V. Berryhill

Reconnaissance studies of beach deposits along approximately 220 miles of the shoreline of Bristol Bay, Alaska, were made to determine if more detailed investigations were warranted. In addition to preliminary mapping of the deposits, samples were obtained from auger borings spaced at 1-mile intervals in key areas; shovel samples were collected to supplement the borings. Most samples were roughly concentrated in the field; magnetic separation tests, petrographic analyses, and determinations for radiometric equivalent uranium, gold, platinum, iron, and titanium were made in the Bureau of Mines laboratory at Juneau, Alaska. Spot samples from some beaches along the shores of the Alaska Peninsula indicate small deposits containing up to 10 percent recoverable titaniferous magnetite; some larger deposits were indicated to contain from 1 to 2 percent total heavy metal, principally as titaniferous magnetite. Significant amounts of other commercial minerals were not detected.

Jan 1, 1963

By P. R. Tisot

Structural response and/or deformation was determined for each of four different grade Green River oil shales (27.0-, 34.5-, 45.5-, and 63.5-gal/ton) as they were heated in an inert atmosphere, under constant compressive stress, from ambient to subretorting temperatures; that is, below those required for rapid pyrolysis of the organic matter. Small cores and small columns of confined fragments comprised the test specimens, which were heated, in a specially designed microunit, at a uniform rate either to 725° or to 825° F under three different stress levels, 80, 200, and 325 psi. Structural response of some cores was observed as they were heated in a stress-free environment. The obtained stress-strain-time-temperature relationships provide information regarding the oil shale's yield temperature, yield stress, rate of compressive strain, loss of mechanical strength, and nature of structural deformation. Effects of structural deformation on induced permeability in small columns of fragments are presented. Results indicate that underground retorting of Green River oil shale may be seriously impaired through loss of induced permeability brought about by structural deformation of rich oil shale under the influence of heat and compressive stress.

Jan 1, 1971

By G. R. Peterson

To determine the availability of lead and zinc from demonstrated resources, the Bureau of Mines evaluated 235 mines and deposits in 31 market economy countries. Of the 235 mines and deposits evaluated for this study, 186 were evaluated as zinc operations, 30 as lead operations, and 19 as copper operations. Demonstrated lead-zinc resources of market economy countries in 1981 were approximately 4.3 billion metric tons (t) of ore containing 221 million t of zinc and 97 million t of lead. Of these amounts, approximately 154 million t of zinc and 70 million t of lead are estimated to be recoverable. The analyses indicate that demonstrated resources in market economy countries should be sufficient to satisfy projected demand for primary lead and zinc through the balance of the century. The U.S. lead industry will continue to have a comparative advantage over the rest of the world industry, barring any drastic increase in the cost of compliance with pollution control regulations. It appears that the comparative disadvantage faced by the U.S. zinc industry will probably intensify owing to the relative quantity of lower cost zinc resources in other countries, especially Canada, Australia, Mexico, and Peru.

Jan 1, 1985

By Stephen C. Tadolini, Peter (Yunqing) Zhang

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of “primary support” and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

By John C. Gagliardi, Walter K. Utt

The U.S. Bureau of Mines, in cooperation with Carter Mining Co., conducted vibration tests of four off-road vehicle seats. The purpose of the tests was to determine which seat provided the best vibration attenuation under laboratory conditions. Laboratory tests were constructed to simulate the mining vibration environment within the limitations of the test equipment. The acceleration test levels and corresponding response of the seats were low compared to IS0 2631's fatigue-decreased-proficiency time limits. Two of the seats employed mechanical suspensions and two seats employed air suspensions. The seats were tested using a 22,241-N (5,000-lbf) electrodynamic shaker. Mechanical suspension seats were tested with various preload-to-mass ratios (PMR's) and cushion densities. Air suspension seats were tested with various air pressure levels and seat cushion densities. Air suspension seats provided good vibration attenuation if pressurized greater than 552 kPa (80 psi). Mechanical suspension seats' attenuation performance decreased if the PMR exceeded 9.8. Seat cushions of lower density provided less vibration damping.

Jan 1, 1993

By Mark S. Sanders

This report presents recommended visibility requirements for continuous miner, shuttle car and scoop operations and details the methodology used to generate them. A task analytic approach was used to define information requirements and visual features which served as sources of information. Information requirements were prioritized and the location of visual features determined. From this analysis, visual attention locations, containing one or more important visual features, were identified. A total of 71 locations-were identified for continuous miners, 54 for shuttle-cars and 54 for scoops. A procedure was developed for assessing whether operators in existing machines could be expected to see the visual attention locations. The procedure makes use of a Human Eye Reference Measurement Instrument (HERMI) designed for this project and an outside-in photographic procedure for documenting compliance with the recommendations. A sample of continuous miners, shuttle cars, and scoops were used to test the procedure. Results are presented in the report.

Jan 1, 1981

By D. E. Kirby

The electrochemical reduction of AlC13 was investigated as a process for the production of aluminum. An externally heated, single-compartment cell with a rammed refractory lining was used with molten KCl-NaCl-AlC13 electrolyte. Aluminum was deposited qt 700° to 760° C with a current of 100 to 200 amperes on a molten aluminum cathode. Chlorine was evolved at a graphite anode and collected and measured to provide a quantitative evaluation of the AlC13 reduction. Aluminum was removed from the cell by siphoning or ladling. Granular AlC13 was added periodically to replenish that depleted from the electrolyte. Concentrations of 7.5 to 17.5 percent AlC13 in the electrolyte were optimum for operation. Anode current efficiencies of 83 to 85 percent were attained, using anode current densities of 5.9 amperes per square inch and an anode-cathode distance of 4 inches. The chemically bonded, alumina liner was resistant to attack by aluminum and chlorine but susceptible to erosion at the surface of the electrolyte. Titanium diboride proved suitable for the electrical connection to the molten aluminum cathode. Aluminum of a purity equal to or better than 1100 series metal was electrowon continuously from commercial AlC13 for a period of 4-1/2 months.

Jan 1, 1970

By Susanne Hering, Brent Kirby, Charles D. Litton, Tracy Allen, Kirk R. Smith, Rufus Edwards

In developing countries, high levels of particle pollution from the use of coal and biomass fuels for household cooking and heating are a major cause of ill health and premature mortality. The cost and complexity of existing monitoring equipment, combined with the need to sample many locations, make routine quantification of household particle pollution levels difficult. Recent advances in technology, however, have enabled the development of a small, portable, data-logging particle monitor modified from commercial smoke alarm technology that can meet the needs of surveys in the developing world at reasonable cost. Laboratory comparisons of a prototype particle monitor developed at the University of California at Berkeley (UCB) with gravimetric filters, a tapered element oscillating microbalance, and a TSI DustTrak to quantify the UCB particle monitor response as a function of both concentration and particle size and to examine sensor response in relation to changes in temperature, relative humidity, and elevation are presented here. UCB particle monitors showed good linearity in response to different concentrations of laboratory-generated oleic acid aerosols with a coarse (mass median diameter, 2.1 µm) and fine (mass median diameter, 0.27-0.42 µm) size distributions (average r2 = 0.997 ± 0.005). The photoelectric and ionization chamber showed a wide range of responses based on particle size and, thus, require calibration with the aerosol of interest. The ionization chamber was five times more sensitive to fine rather than coarse particles, whereas the photoelectric chamber was five times more sensitive to coarse than fine. The ratio of the response between the two sensors has the potential for mass calibration of individual data points based on estimated parameters of the size distribution. The results demonstrate the significant potential of this monitor, which will facilitate the evaluation of interventions (improved fuels, stoves, and ventilation) on indoor air pollution levels and research on the impacts of indoor particle levels on health in developing countries.

By Wilton Johnson

The Bureau of Mines study indicates that land utilized by the mining industry for mineral extraction and processing from 1930 through 1980 amounted to 5.7 million acres, or 0.25 percent of the land mass in the United States. Land reclaimed by the industry during the same period was 2.7 million acres, or 47 percent of the land utilized. Land use by the mining industry includes surface land used for excavation or mining, for waste from underground mining, and for wastes from milling or processing operations. Data on land use for disposal of overburden waste from surface coal mines and on areas affected by subsidence associated with underground mining are included for the period 1930-71 only. The 10 leading States in total land used for mining over the 51-year period were, in decreasing order, Pennsylvania, Kentucky, Ohio, Illinois, West Virginia, Florida, Indiana, California, Alabama, and Missouri. Seven mineral commodities accounting for 92 percent of land use are, in decreasing order, bituminous coal, sand and gravel, stone, phosphate rock, clay, copper, and iron ore, all predominately surface mined. Bituminous coal production was responsible for nearly half of the total area utilized. Reclamation of mined lands and waste disposal sites over the reporting period was largely on lands utilized in mining bituminous coal; 75 percent of the land used for bituminous coal production was reclaimed.

Jan 1, 1981

By R. S. Dean

The brief resume of the activities of the Metallurgical Division that appears annually in its progress reports series serves a useful purpose by making available a rather comprehensive but concise recapitulation of the current work, and publications of the division. An unprecedented opportunity to attack the problem of producing ferro-grade material from low-grade domestic manganese ores effectively was provided by the act designated as Public 667 of the 76th Congress of the United States, approved June 26, 1940, which made available an appropriation for "Expediting Production of Equipment and. Supplies for National Defense." Although the funds were not immediately available to the division, good progress has been made in the, solution of the many and diverse problems presented in the studies undertaken to determine the best methods for the recovery of useful products from a wide variety of manganese ores.

Jan 1, 1941

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

By H. R. Babitzke

As part of a continuing project to develop refractory metal alloys for high-temperature structural applications, the Bureau of Mines applied solid solution and precipitation strengthening techniques to improve the properties of columbium alloys. The purpose was to investigate the effects of hafnium, tungsten, and boron on the formability, strength, and oxidation resistance of columbium. The experiment was of factorial design with two replications which called for 72 ingots of 36 basic compositions, weighing 150 grams each. Hafnium, tungsten, and boron were evaluated at 3, 3, and 4 levels, respectively. Values of alloy content are all in atomic percent. The highest strength observed was 29,000 psi at 1,200° C for alloys Cb-15Hf (No. 3), Cb-7.5Hf-5W-2B (No. 14), and Cb-15Hf-5W-2B (No. 15). At 1,200° C, the ternary alloy Cb-15Hf-5W (No. 6) which has shown good properties in previous Bureau of Mines investigations was the most resistant to oxidation For boron additions, the alloys oxidized more readily with increasing amounts of this element. The fabricability of the alloys high in boron became increasingly difficult, resulting in an inadequate number of alloys required for a complete statistical analysis for all the tests. As a result of the decrease in ductility, an insufficient quantity of tensile samples were available for a proper analysis for the high-temperature strength data.

Jan 1, 1970

By M. Beus, S. Inverson, B. Stewart

Abstract Recent ore pass failures have underlined the need for improved designs, standards, structural mon¬itoring methods and better hang-up prevention and removal tech¬niques. Researchers at the Spokane Research Laboratory of the Na¬tional Institute for Occupational Safety and Health (NIOSH) are investigating methods to improve safety during the transport of ore in ore passes. Design criteria and hang-up prevention and remedia¬tion strategies involve studies of the effects of static and dynamic ore and waste-rock loads on chutes, walls, gates and support structures. Particle flow analysis methods were used to simulate the response of various ore pass designs to a wide range of ore loading condi¬tions. A full-scale mockup of ac¬tual ore pass and chute assemblies was duplicated and tested for load response. Data from a particle flow code and the mock-ups were com¬pared Loads on an active ore pass chute were measured.

By Steven J. Page, John A. Organiscak

The amount of airborne respirable dust generated from break- age of different coals varies widely. This research was conducted to identify the facets of airborne respirable dust liberation from the coal product. Laboratory crushing experiments were conducted on a range of low to high volatile bituminous coals to investigate the various factors influencing airborne respirable dust generation. Bituminous coal samples from 8 mines (5 U.S. and 3 Polish) were uniformly prepared and processed through a double roll crusher located in a low air velocity wind tunnel. Experimental factors studied included inherent coal seam constituents, specific energy of crushing, product size characteristics, dust cloud electrostatic field, and specific quantity of airborne respirable dust generated. The results of this investigation build upon previously published results, which indicated that a combination of several factors are associated with the generation of airborne respirable dust. One factor involved is the effect of coal rank, described by the inherent moist fuel ratio, on the product size characteristics, defined by Schuhmann size function parameters. However, since coals of high moist fuel ratio (high rank) are generally more extensively cleated, it is suggested in the present work that the degree of cleating is directly responsible for the quantity of respirable-sized particles produced in the crushed product material for eastern U.S. coals. This is implied by the relationship of ash content and at least one mineral constituent (pyrite, determined from pyritic sulfur analysis) to the percentage of airborne respirable dust. To validate this hypothesis, a description is offered that is based on known coal petrography. Another key factor is the effect of air dry loss moisture in the coal seam on the breakage-induced electrostatic field of airborne dust. The air dry loss moisture factor appears to control the amount of airborne respirable dust that is liberated from the product. The resultant effect of these factors is that different percentages of coal particles smaller than 10 µm are dispersed as airborne respirable dust with a well-defined peak in the normalized airborne respirable dust for a narrow range of air dry loss moisture - ash ratios. A clear delineation of coals, based on well-known proximate analysis characteristics, that generate the most respirable dust appears to be possible. It was also shown that the dust-generating characteristics of coals could be reasonably described by both the moist fuel ratio

By Paul M. Ambrose

Overall the domestic abrasives industry had one of its best years in 1965. Production and value of all commodities increased over that of 1964 which also was a good year. Production of tripoli that was down in the previous year rebounded and production from two new mines was reported. Plant capacities for production of silicon carbide and fused crude aluminum oxide and production from plants in the United States and Canada increased, but demand was high and yearend stocks were less than at the end of 1964. Foreign Trade.-Increases in value of most imports of abrasive materials in 1965 were offset by a decrease in the value of imported industrial diamond. Production of fused aluminum oxide and silicon car-bide in the United States and Canada and imports of these commodities into the United States increased, but combined exports of finished grain of these materials was virtually unchanged from the previous year.

Jan 1, 1966

By Verne E. Hooker

Stress-relief techniques and instrumentation have been developed through many years of research in the Federal Bureau of Mines and successfully used to determine the in situ state of stress in rock. This paper describes the drilling equipment and accessories for use with the Federal Bureau of Mines three-component deformation borehole gage. Operation and calibration procedures for the deformation gage are discussed in detail. Site selection and overcoring procedures are included to provide a complete working knowledge for surface or underground applications.

Jan 1, 1974