Search Documents

By D. K. Ingram

In situ horizontal stresses were measured to determine the influences of geologic anomalies on the regional horizontal stress field in two coal mines in southern Illinois. Stress measurements were obtained near a normal fault having a 121-ft displacement at the AMAX Wabash Mine and a large coalbed want at the Kerr-McGee Galatia No.5 Mine. Horizontal stress measurements were completed using a Bureau of Mines borehole deformation gauge. The average maximum and minimum horizontal compressional stresses at the Wabash Mine were 1,400 and 800 psi, with the direction of maximum stress ranging from N 78° W to N 83° E. At the Galatia No.5 Mine, the averages were 1,500 and 500 psi, with the direction of maximum stress ranging from N 85° E to N 75° E. Generally, the geologic anomalies appear to have no dramatic effect of the regional horizontal stresses. However, subtle differences between stress measurements suggest an influence by the fault zone at the Wabash Mine. The larger anisotropic stress conditions at the Galatia No.5 Mine could be responsible for the increase in kink zones and directional roof failures.

Jan 1, 1988

By K. C. Dean

During the course of the investigation of manganese mineral occurrences in the western United States, the Bureau of Mines collected several lots of ore' from properties in the vicinity of Winkelman, Ariz. As none of the ores would be marketable directly, an investigation was made to determine their amenability to concentration by ore dressing. The Geronimo group of claims is in Pinal County, 8 miles west of Winkelman, Ariz. The manganese oxides occur as cementing material in ore zones of conglomerate. Representative samples of a 2-ton lot of ore cut from outcrops of two lenticular deposits were laboratory-tested. Two 1-ton samples from the Benningfield property were similar in physical characteristics but differed in grade. This claim is 11-1/2 miles south of Winkelman and about 1 mile west of the San Pedro River on the south side of Putman, Wash. The manganese minerals occurred as nodules and lenses, replacing limestone, in a capping over a dark, igneous dike. The North Star group consists of five claims on the west side of the San Pedro River 14 miles south of Winkelman. The ore consists of a low-grade, manganese oxide-calcite occurrence interspersed with stringers of higher-grade material and is present as filling in a fissure zone in porphyry. Two samples were obtained by the examining engineer; one sample represented run-of-mine material, the other represented ore from the vein that could be hand-sorted or selectively mined.

Jan 1, 1952

By C. C. Merrill

The Bureau of Mines beneficiated the wastes generated by commercial titanium chlorination operations to reclaim metal values and reduce the problem of disposing of solid wastes. A water leach solubilized about 40 percent of the dry weight and over 75 percent of the metallic impurities. The residue from the water leach was rich in titanium dioxide and carbon; it was combined with rutile and recycled to a laboratory chlorinator. The contained carbon was used in lieu of part of the coke requirement.

Jan 1, 1969

By K. E. Stanfield

This report presents the results of analytical studies made on two series of oil-shale samples from the Mahogany ledge of the Green River mine the character of the various grades of oil shale that are being mined and processed into shale oil and refined products at the Bureau of Mines Oil-Shale Demonstration Plant at Rifle, Colo. The analytical work was part of a synthetic liquid fuels program being conducted at the Petroleum and Oil-Shale Experiment Station, Laramie, Wyo. The 16 oil shales ranG6d in color from a gray brown ( or a sample that assayed 10.5 gallons of oil per ton to a very dark brown for a sample that assayed 75.0 gallons of oil per ton. In general, the samples were similar as to the types of organic and inorganic matter that they contained but varied widely in the amounts or these constituents. The principal constituents were calcite, dolomite, illite, and yellow organic material, while the minor constituents were quartz, feldspar and plagioclase feldspar, pyrite, marcasite, analcite, opal, black organic material, and small woody fragments. Some micro-fossils, spores and pollen grains were found also.

Jan 1, 1951

By Bertrand L. Johnson

Barite, the natural sulfate of barium (BaSO4), is the most important barium mineral. Normally it is white (opaque to translucent), but impurities sometimes render it yellow, gray, blue, brown, red, or black. Brown or red stains are commonly caused by iron oxide. Barite is unusually heavy (specific gravity, about 4.5); in fact, it is one of the heaviest of the nonmetallic minerals. It is brittle and fractures unevenly. The hardness of barite ranges from 2.5 to 3 but is usually about 3. It can be scratched by a copper coin. Pure barite contains 65.7 percent BaO and A.3 percent S03. Much of the crude barite ore mined, however, contains impurities; thus it has a lower content of barite and consequently less barium oxide. Commercial analyses show its total BaSO4 content. Barium also occurs in nature as the mineral witherite (BaCO3), which, however, is not common in the United States, and commercial deposits have been found only in California. Witherite is a yellowish-white, light-gray, or Kite mineral with a specific gravity of about 3, a hardness of 3 to 4, and an uneven to subconchoidal fracture.

Jan 1, 1941

By A. B. Hooker, E. J. Coggeshall

"Dry cells are modified wet primary cells in which the electrolyte is held by absorbent material so that it does not spill aid the cell jars are sealed to prevent evaporation of the absorbed electrolyte. Most dry cells in commercial use are modifications of the Leclanche wet cell. In their usual form they have a hollow cylindrical zinc negative pole that constitutes the containing vessel. An absorbent material, either as a lining in the zinc jar or a bag, separates the zinc cylinder and a rod or flat plate of carbon placed axially inside. A mixture of crushed coke, graphite, and manganese dioxide is tamped about the carbon rod, and the whole mass is saturated with salaanoniac-zinc chloride solution.Dry cells are suitable for services that require minute currents continuously or larger, though limited, amounts of current intermittently. Though limited in this way, they have a wide use, even in underground mining. This paper details some of the applications of dry cells in mines, particularly from the standpoint of greater safety through their use.APPLICATIONSThere are four fields of application of dry cells to mining: (1) Electric shot firing; (2) auxiliary lighting; (3) signaling; and (4) testing.SHOT FIRINGFiring an electric detonator requires very little electrical energy because although the current flow may be 1 to 3 amperes the duration of flow is so small (1 to 4 milliseconds) that the energy withdrawal per shot is almost negligible. Batteries for shot firing need not be large; they may be used for firing either single or multiple shots."

May 1, 1934

By A. J. Miscoe, W. M. McKewan, J. R. Bartels

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Two 2 in-diameter 6x25 fiber core (FC) ropes were degraded on a bending fatigue machine. These were the second and third ropes in a series of tests on this construction and size rope. Tensile and nondestructive tests were performed on samples of the rope Lo determine the relationship between rope deterioration and rope breaking strength. The tests indicated that once a wire rope nears the end of its service life, both deterioration and the consequent loss of rope strength begin to increase at an accelerated rate.

Jan 1, 1992

By J. R. Bartels

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Two sin-diameter 6x25 fiber core (FC) ropes were degraded on a bending fatigue machine, These were the second and third ropes in a series of tests on this construction and size rope. Tensile and nondestructive tests were performed on samples of the rope to determine the relationship between rope deterioration and rope breaking strength. The tests indicated that once a wire rope nears the end of its service life, both deterioration and the consequent loss of rope strength begin to increase at an accelerated rate.

Jan 1, 2010

By D. A. Larson

The Bureau of Mines conducted basic experiments to study the process of crack propagation with a wedge indenter. The work was conducted under plane stress conditions in a hard, brittle limestone. The purpose of these experiments was to first gain an understanding of the basic crack propagation process under a sharp indenter, and second, to determine how the crack propagation process could be used to improve mechanical fragmentation systems. Three methods of rock fracture with the wedge indenter were investigated in this program. These were the confined indentation tests, the unconfined splitting tests, and the edge chipping tests. The confined indention tests represent worst case conditions for crack growth and formed the lower bound on fracture efficiency. The unconfined splitting tests represented best case conditions and fixed the upper bound of fracture efficiency. The edge chipping tests represented an idealized fragmentation process based exclusively upon the highly efficient fracture propagation process. Edge chipping achieved a specific energy of 25 in lb f/in3 compared to conventional drag cutters, which required a specific energy of at least 2,385 in·lb f/in3? Thus edge chipping is up to 100 times more efficient than conventional drag cutting. Because of these promising results, more work is planned with the fracture propagation process in three dimensions.

Jan 1, 1987

By T. C. Moore

This report describes the feasibility test of an electromagnetic method for locating boreholes, with or without casing, that have been drilled in conjunction with mining operations but whose location with respect to the tunnel is not precisely known. The first tests were conducted with the cooperation of the Kerr-McGee Corporation, Church Rock Mining Operations, New Mexico, in September 1977. These tests demonstrated that accuracies of better than ±5% of range and ±1° of bearing can be achieved with a simple system and setups. Subsequent tests, in January 1978, on a horizontally drilled pipe line river crossing application, by Titan Contractors of Sacramento, California, demonstrated that accuracies of better than one-half percent of range and a few tenths of one degree of bearing can be achieved by using refined techniques. The demonstration tests were done at ranges on the order of 100 to 200 feet but the method is capable of working at much greater distances.

Jan 1, 1978

Over 500 industrial, academic, and government representatives from Europe, Canada, and the United States attended the first large symposium ever held in this country on fly ash utilization and technology, March 14-16, 1967, at Pittsburgh, Pa. Sponsored by the Edison Electric Institute, the National Coal Association, and the Bureau of Mines, the symposium featured 27 formal presentations by leading reports from the United States and Europe on all major phases of fly ash production, utilization, and research. Representing the three sponsoring organizations were Edison Electric Institute, James D. William- son, The Dayton Power and Light Co.; National Coal Association, James R. Garvey, Bituminous Coal Research, Inc; and Bureau of Mines, Harry Perry. Symposium chairman was John H. Faber of the Bureau of Mines. Gerard C. Gambs, Consolidation Coal Co., addressed the opening session. Moderated by Mr. Garvey, President and Director of Research of Bituminous Coal Research, Inc., the opening session was devoted to a discussion of the nature of the fly ash problem, including availability, specifications, and limitations on its use. Subsequent sessions covered Fly ash marketing, fly ash utilization in concrete and masonry products, specialized uses, and recent developments in basic fly ash research. Others serving as session chairmen were Oscar E. Manz, Associate Professor of Civil Engineering, University of North Dakota; Mrs. Katharine Mather, Chief, Petrography and X-ray Section, Concrete Division, U.S. Army Engineers Waterways Experiment Station; Mr. Williamson, and Mr. Perry.

Jan 1, 1967

By Peter Grandone

"INTRODUCTION The injection of water into partly depleted-oil-bearing formations as a means of supplying additional energy to flow oil wells now is recognized by the petroleum industry as an effective method of increasing the recovery of oil. The benefits to be derived from water-flooding oil sands were discovered accidentally more than 4o years ago, when oil producers in the Pennsylvania and western New York fields observed suustantial increases, in oil-production rates when water leaked past corroded casings of old wells into producing sands. This observation prompted some operators purposely to perforate or slit the casings opposite the producing formation in some of their wells to permit water to enter the formation. However, as many operators viewed the practice with skepticism and considered it to be in violation of oil-conservation principles,- systematic water-flooding was not initiated until the Pennsylvania legislature, in 1921, enacted a law authorizing water-flooding of oil sands in that State.Although water-flooding has been practiced in a haphazard manner for more than 25 years in Chautauqua and Montgomery Counties, Kansas, planned or systematic water-flooding in that State had its inception in 1935, when the legislature, following the example of Pennsylvania, also passed a lava/ authorizing water-flooding. The early operations and, to some extent, those still, practiced in the Chautauqua-Montgomery area consisted in raising or perforating the casing to allow water from upper strata to gravitate into underlying oil-producing formations. The extent to which this type of water-flooding affected petroleum production in the old stripper area of eastern Kansas is not known, but it is known to have increased oil production ap¬preciably from many leases.Following enactment of the law permitting water-flooding in Kansas, three operators inaugurated, in that same year, three organized flooding projects in three different counties of the southeastern part of the State. The first organized project on record was that of the York State Oil Co. in the Seeley pool, Greenwood County. On this project, the injection was started on May 15, 1935, into the Bartlesville sandstone at a top depth of 1940 feet."

Jul 1, 1944

By Norman G. Foster

The mass spectra of four tertiary butyl substituted thiophenes are reported. A comparison and contrast with earlier structure correlations made by API-RP48 mass spectroscopists is presented. The fragmentation routes of these types of molecules are discussed and explained in terms of existing theories in mass spectrometry. Low ionization voltage data are presented to support the mechanistic picture developed. Structures are inferred about some of the ions, and these are correlated with existing theories. Metastable peaks in the spectra are used to support the fragmentation paths. The presence of doubly charged ions in the spectra is noted and the possible implications toward mechanisms discussed. The general picture of simple, small fragments leaving the ion moiety upon further fragmentation is developed in detail. Some suggestions are presented for further work utilizing isotopically labeled molecules to establish firmly the general picture of fragmentations of the alkylthiophenes.

Jan 1, 1966

By J. S. Hansen

To advance technology that can conserve critical materials, the Bureau of Mines investigated a cast-on hard-surfacing that wear resistance and confines alloy additions to wear-prone surfaces. Wear-resistant material in form is on a polystyrene , the is embedded in a mold of unbonded s and the wear-resistant material is transferred to a cas surface at the time of For low-stress abrasion, derived from high-carbon ferro-chrome had higher wear resistance than did commercially available weld-hard. The microstructure of the was typi-white iron carbides. Free carbon added to the ferrochrome powder produced more M7C3 carbides than did material contained in surfacings made from ferrochrome alone, and improved the wear resistance. Several white iron powders with greatly reduced chromium contents also white iron contain-M7C3 carbides. One derived from white iron powder had wear resistance to that of weld-deposited hard facings. Among the parameters investigated, surfacing thickness was found to have a or influence on diffusion of elements out of the , microstructure, and wear resistance. The results of field tests on bucket-wheel excavator teeth and plowshares with cast-on hard surfacing are given.

Jan 1, 1985

By W. C. Holliman

Commercial production of synthetic rubber in the United States became a reality in 1931 when E. I. duPont de Nemours, Inc., announced the manufacture of Duprene, a synthetic rubber made by polymerizing r chloroprene. Duprene was later improved and reintroduced as neoprene. Since 1931 other synthetic rubbers and rubberlike materials have been announced and are now produced commercially or are in the pilot-plant stage in the United States. These include Thiokol, Buna S, Perbunan, Koroseal, Vistanex, Flamenol, Ameripol or Hycar, Chemigum, Butyl rubber, and Flexon. None of these is synthetic rubber in the strict chemical meaning of the word synthetic, as none is identical in chemical structure with natural rubber. However, all possess some of the physical properties of natural rubber, and in addition usually have some outstanding property not found in natural rubber that makes them superior for certain uses. Because of these superior qualitites, a considerable demand had arisen for synthetic rubbers before the present emer¬gency, although the price was several times that of natural rubber.

Jan 1, 1943

By P. R. Bradley

This paper is one of a series , dealing with mining methods and costs , sponsored and published by the U. S. Bureau of Mines . Papers of this series are written by engineers and executives of mining companies , at the solicitation of the Bureau , and in accordance with an outline prepared by Bureau engineers , for the purpose of securing uniform presentation and conformable data . The property of the Alaska Juneau Gold Mining Co. is situated near the city of Juneau , Alaska , in what is known as the Harris mining district . Wholesale mining operations have been adopted on a large scale and 10,000 to 11,000 tons per day of gold- bearing ore are mined and sent to concentrators near Juneau . In addition to gold , the ore yields 0.6 ounce of silver and 13.0 pounds of lead to each ounce of gold recovered .

Oct 1, 1929

By W. W. Adams

Coal mining in the United States established a good safety record in 1939. The death and injury rates per man-hour of exposure to risk were favorable compared with most previous years, and the number of persons killed or injured in proportion to the quantity of coal mined was also lower than in any other year for which figures are available. Moreover, productivity per man-hour was higher than ever before. The number of man-hours of work performed increased 9 percent over 1938, but there was a slight decrease in the number of men employed. Reports from operating companies showed 539,375 men employed during the year, and the period of operation averaged 179 workdays per man. Man-hours of work numbered more than 678 million. Accidents to the workers resulted in 1,078 fatalities and 54,015 nonfatal disabling injuries, causing disability of the employee for more than the remainder of the clay on which the accident occurred. For each million man-hours of exposure of the employees to mining hazards the fatality rate was 1.59 compared with 1.78 for 1938, and the injury rate was 79.65 compared with 82.61 for 1938. Production of coal averaged 0.661 ton per man-hour compared with 0.637 ton in 1938. The weighted average length of the workday was 7.03 hours or virtually the same as the previous year's average of 7.04 hours. Measured in man-hours, the average period of employment per man was 1,257 hours in 1939 and 1,147 hours in 1938.

Jan 1, 1942

By James C. Barker

The analytical variability encountered when sampling for platinum-group metals (PGM) was statistically evaluated during a 1983 study by the Bureau of Mines and the University of Alaska. Sampling procedures were designed to systematically incorporate commonly used reconnaissance exploration techniques under actual field conditions. Analytical variability was evaluated at each procedural step. Analytical data from each sample from a single deposit grouped relatively well around the calculated mean for that deposit. Standard deviations did not exceed 43 pct of the mean for any of the deposits; more commonly, the deviation was about 25 pct. Statistical treatment of the data by analysis of variance indicated the most important source of error is selection of the sample site. Two or more replicate samples appear necessary to adequately quantify the PGM content. Secondly, significant variation occurs during preparation of a pulverized split for fire assay. The optimum sample size was in the 11-lb range; larger samples did not appreciably reduce variability. Smaller samples generally indicated a higher degree of variability. Evaluation of the sample method suggested the common grab sample, if carefully taken, is a useful indicator of the general range of PGM concentration but potentially includes a considerable margin of error.

Jan 1, 1985

By G. R. Hopkins

According to reports received by the Bureau of Mines, Department of the Interior, as of January 1, 1934, there were 591 completed refineries in the United States, an increase of 86 ever the total reported at the beginning of 1933 and the largest total ever recorded. It should be noted that the 1934 total, although large, probably does not include more than half of the "pot-still" plants of 1 barrel to 50 barrels daily capacity which have sprung up within the last 2 or 3 years and about which very little information is available. However, the combined operations of these snail refineries are of negligible importance as altogether they refine less crude than one plant of average size. Of the completed plants, 454 were operating on January 1, 1934 and 137 were shut down. In addition, 13 refineries were under construction on January 1, 1934. Compared with the previous year these data indicate a marked increase in the number of operating plants, little change in the number of inoperative plants, but a decline in' the number being built. The material gain in the number of operating plants resulted primarily from the construction off approximately 25 refineries, averaging about 100 barrels capacity in the Kooky Mountain district, as well as from the addition of about 20 plants in the East Texas field.

Jan 1, 1934

The value of U.S. mineral raw material output reached a record $63.1 billion in 1975. This high exceeded the 1974 value of $55.2 billion by 14 percent. Among the three major mineral categories -fuels, metals, and nonmetals -only fuels showed an increase in value. Both the metal and nonmetal categories showed declines in value. The significance of this nearly $63 billion mineral output can be noted in the fact that it is the basis for the subsequent production of over $270 billion a year in energy and processed materials. Of the 78 individual mineral commodities included in these 1975 totals, only 17 registered gains in output, while 45 registered value increases, reflecting higher prices.

Jan 1, 1976