Search Documents

By Terry J. Close

The Welcome Creek Wilderness has small, dispersed gold placers. Pockets in the 25.5 million yd3 (19.5 million m3) of alluvium along Welcome and Rock Creeks have as much as $5.61 gold/yd3 ($7.34/m3) at $500/troy oz ($16.08/g). All the alluvium averages 20.1 cents gold/yd3 (26.3 cents/m3). Because of the low average gold content large-scale placer mining would not be economically feasible. Small-scale selective pocket mining, however, may be profitable. The alluvium along the streams in the Wilderness has little apparent potential for production of sand, gravel, or stone because alternate sources are closer to markets. The four lode prospects known within the Wilderness appear to have low mineral potential. No oil, gas, uranium, or geothermal energy sources are known to be present.

Jan 1, 1982

By R. D. Saltsman

This report is in fulfillment of Contract No. H023001.5 awarded to Bituminous Coal Research, Inc., on November 15, 1972. The scope of the work under this contract was to perform a two-phase survey for the purpose of determining the status of work in the following specific areas of industry needs under the Technology Transfer Program and to increase industry's awareness of research efforts under the Federal Coal Mine Health and Safety Act of 1969 6f (P.L. 91-173): 1. Research and development of respirable dust sampling instruments which will more accurately collect the respirable Cuss as defined by the Federal Coal Mine Health and Safety Act of 1969. 2. Development of a better means of control of respirable dust and float dust.

Jan 1, 1973

By Natesa I. Jayaraman

A field study was conducted by the Bureau of Mines to determine the feasibility and effectiveness of a secondary ventilation system retrofitted onto an Eickhoff EDW 340L double-drum shearer as a technique for controlling respirable dust generated during a longwall mining operation. An airflow duct was formed by enclosing the bottom of the undercarriage with steel plate and cutting air channels through the ends of the undercarriage frame. Air intakes were provided behind each cutting drum and at several locations along the undercarriage. Grills were installed at the intakes to prevent the broken coal from entering the ducting. A dust collector consisting of 5,000-ft3/min fan, water sprays, and a minicyclone panel was installed on the shearer at the tailgate end. Field results indicated that the secondary ventilation system reduced respirable dust more than 60% along the face. Reduction was less near the intake airway and when secondary dust sources occurred.

Jan 1, 1977

By John C. Edwards, Gene F. Friel

A series of liquid fuel fire experiments evaluated the comparative responses of five types of commercially available smoke detectors and a diffusion-mode carbon monoxide (CO) detector under normal and reduced airflow conditions based upon the alarm times of the detectors. These experiments were conducted in the Safety Research Coal Mine at the U.S. Bureau of Mines Pittsburgh Research Center. Two of the smoke detectors had manufacturer set alarms. For the other three smoke detectors, an alarm point was defined in terms of their background analog signal and the detector's electrical output noise under ambient conditions. A correlation was developed of the travel time of 5 ppm CO between pairs of CO detectors with the travel time calculated from entry and crosscut volumes and measured airflow. Based upon the relative performance of smoke detectors in this limited study, smoke detectors can be as effective as CO detectors for mine fire detection once identifiable alarm values are defined. Implementation of smoke detectors as part of an atmospheric mine monitoring system will improve mine safety.

Jan 1, 1996

By Herman O. Ankenbruck

Analyses of statistical data indicate that haulage accidents are one of the largest sources of injuries and fatalities in underground coal mines, and that the rate of accidents in transportation has been increasing during the past few years. These previous analyses were performed by correlating accident or fatality data at a rather high level of miner activity. In this present investigation, underground surveys were made by observing conditions and activities in some detail at a rather low level of activity in an attempt to understand factors contributing to hazards in the specific situations observed. The aim of the current study was to derive preventive measures that might obviate the hazardous conditions and unsafe acts observed; and, following this, to provide recommendations for additional research and development to reduce accident potential in underground transportation. The major project tasks are diagrammed together with the task outputs in figure 1-1. Initially, a preliminary study of ell underground haulage operations was performed in order to establish the kinds of data needed and to provide the rationale leading to the data requirement. At the same time, the various types of haulage equipment used for each operation were defined. A preliminary analysis of each type of haulage operation was performed in order to establish the sequence of tasks required to operate haulage equipment. These tasks were transferred directly onto observation forms, and were used in developing interview forms. In parallel with the task analysis, a review was made of accidents and hazards that might occur during each type of operation.

Jan 1, 1975

By Robert Blickensderfer

Tungsten alloys with high-temperature strength properties, comparable to the best of alloys recently developed by others, were produced by a new process called here the oxyreaction process. The process involved additions of a powder of a reactive metal compound, ZrN, ZrW2, or HfW2, to a base metal powder, tungsten, which contained some oxygen. The powders were blended, compacted, sintered, and extruded. During sintering, diffusion and internal oxidation occurred to produce reactive-metal oxide particles and solid solutions. A dispersion of oxide particles could be precipitated by heat treating. The oxyreaction process circumvents many of the agglomerating and coarsening problems encountered in the current methods for dispersing a stable oxide in a metal. Oxyreaction strengthening results from solid-solution strengthening and from dispersion strengthening produced by the reactive metal and its oxides. At a test temperature of 1,650° C, the alloys prepared from WW, had tensile strengths up to 70,000 psi and stress-rupture lives up to 142 hr at 10,000 psi stress; the alloys prepared from ZrN powders had tensile strengths up to 80,000 psi and stress-rupture lives up to 27 hr at 10,000 psi stress. Tensile strengthening in the alloys was attributed to Zr in solid solution or to Zr-O-W structures too small to be observed in an electron microscope replica. Stress-rupture life was attributed to a dispersion of submicron Zr02 particles which precipitated and grew to 0.05-to 0.2-micron size during the test. Tensile strengthening and stress-rupture life were dependent upon both the zirconium and oxygen contents with the maximum occurring at roughly 0.9 atomic pot Zr and 0.9 atomic pot 0. Studies of the details of the oxyreaction process were made on the W-ZrW2 alloys and three general steps were determined: (1) The reaction of 0 in tungsten powder with ZrW2 to form relatively large Zr02 particles; (2) the dissolution of remaining ZrW2 into the W matrix and partial internal oxidation to form ultrafine but sparse zirconium oxide particles and possibly to establish Zr-O-W structures; (3) the development of ultrafine Zr02 particles during high-temperature aging.

Jan 1, 1971

By William G. Pariseau

The research reported here concerns a four year study of the rock mechanics aspects of two underground hardrock mine study stopes. The first study was conducted at Anaconda Minerals Company's Carr Fork Mine near Tooele, Utah. The second study was conducted at the Homestake Mining Company's Homestake Mine In Lead, South Dakota. Both case studies were cooperative efforts of mining company personnel, the Spokane Research Center of the Bureau of Mines and the Department of Mining Engineering, University of Utah. Large diameter (6 1/2 In.) blastholes were an integral part of the stoplng method at each mine. A true vertical crater retreat (VCR) method was used at the Homestake Mine, while a vertical bench mining method (VBM) was used at the Carr Fork Mine. VCR and VBM methods were developed In the 1970's; they offer significant productivity gain and are now used throughout the world. The new technology, however, brings with It a requirement for more sophisticated engineering design and control. Since there are no personnel in a VCR or VBM stope, all ground control Including dimensioning of stopes and pillars and the layout of cable bolt assays or other artificial support must be done in advance of production blasting. Accordingly, the objective of the research study was the establishment of a procedure for optimizing stops and pillar sizes. The approach taken was In each case a combination of mine measurements of the study stope response to mining, laboratory testing for rock properties and In situ stress measurements of the premining stress field, and theoretical calculations of the study stope response to mining. All calculations were done with the UTAH-II finite element computer program. Simulation of the blasting sequence gave a correlation of 0.88 between measured and calculated extensometer readings (Incremental relative displacements) at the Carr Fork Mine where other 30 Instrumentation boreholes were used to monitor the test stope response. A correlation of 0.84 was obtained at the Homestake Mine where 19 instrumented boreholes were used for monitoring purposes. These high correlations validated the computer mode and calibrated It for rock mass properties. The calibrated model was then used In parametric studies of alternative design layouts.

Jan 1, 1985

To provide cooler air to miners working in hot areas of mines, particularly new deep hardrock mines. Approach Air supplied to hot working areas of mines is cooled by passing it through a series of water sprays. How It Works Water nozzles mounted inside a section of ventilation tubing release cooling sprays of water into the air being blown through the tube. The prototype of the water spray cooler consists of six evenly spaced water sprays located inside a 10-ft. long section of 16-inch-diameter fiberglass ventilation tubing. See diagram. This section of rigid tubing is installed into one of the positive pressure ventilation tubing lines that conduct fresh air into working stopes. The intake manifold to the six water sprays is connected to the mine?s cool water line, and the water valve on the manifold is opened. Warm ventilation air being supplied to the stope passes through the water sprays, and is cooled by the lower temperature water.

Jan 1, 1979

By M. K. McCarter

Previous investigations suggest the possibility of determining shear strength of geologic materials by measuring the force necessary to rupture the web between two closely-spaced, parallel holes using a borehole jack. Current research using finite element modeling and laboratory testing of intact rock indicates that web failure initiates by tensile fracturing induced by a complex stress field. Based on these results, a theoretical justification for relating web strength with shear strength appears unlikely for holes of equal diameter spaced two diameters apart. Empirical results, however, show a strong correlation between average web strength and average unconfined compressive strength for some rock materials under laboratory conditions. A good correlation also exists between residual web strength and the residual angle of friction under the same conditions. This research project involves the construction and field testing of a large borehole jack. The jack is designed to operate within a conventional 12-1/4 inch rotary blasthole common to open pit mining. The system is capable of exerting approximately 800,000 pounds on curved platen measuring roughly 4x24 inches. Field tests indicate that the system will operate in a mining environment, and preliminary results suggest the possibility of using the force-displacement data generated by the jack to rank the competency of material within a mine bench.

Jan 1, 1982

By Dipak Sengupta

This study analyzes the safety, technology, and economic impact of eliminating safety fuse from metal/nonmetal mines, based on operation and manufacturer experience over the past five to ten years. If safety fuse is eliminated, blasting accidents will decrease with no technical impact except for some limited, specific applications. The economic impact will be minor for large operations, but will be significant enough for small operations that some small operations will likely close rather than change. The majority of the mines would probably change over, with the extra cost absorbed by the market. Elimination of safety fuse would have obvious impact on the two manufacturers of safety fuse; one manufacturer already produces an alternative system, and will remain unaffected; the other will be affected if they do not change their production strategy. There will be a very minor effect on the mining industry as a whole due to abolishment of safety fuse from the standpoint of employment or production.

Jan 1, 1980

By Roger J. Morrell

Bureau of Mines laboratory experiments with reduced scale cutter and cutter forces were performed to (1) define the fundamental relationships governing disk cutter performance and (2) to develop a method of predicting disk cutter performance in soft, medium, and hard rocks. The rock cutting experiments were performed in four igneous and metamorphic rocks that ranged in compressive strength from 38,000 to 67,000 psi. A special testing machine called a linear cutter apparatus (LCA) was used to load and traverse a free rolling disk cutter across a smooth rock surface. Each pass of the disk produced a single crater, and runs were spaced to avoid breakage between craters. During each run the normal and tangential cutter forces were measured and recorded. The soft and medium rock data were obtained from previous Bureau experiments with disk cutters. Crater depth, tangential cutter force, crater volume, specific energy versus normal cutter force, and crater width versus depth are defined within this study. With the use of standard physical properties, performance prediction equations were developed using stepwise linear regression analysis techniques. A method of using these prediction equations to calculate the boring rate, the cutter spacing, and the torque and energy requirements of a full-scale boring machine was also developed.

Jan 1, 1974

By Thomas A. Phillips

The Bureau of Mines presents an economic evaluation of its leach- electrolysis process for recovering lead from galena concentrate. In this process, galena concentrate is leached at 200° F with a ferric chloride-brine solution to extract lead while leaving sulfur in the residue, which is discarded. The solution after leaching is concentrated and cooled to 100° F by vacuum evaporation to crystallize lead chloride from which metallic lead and chlorine are produced by fused-salt electrolysis. Chlorine is used to regenerate the spent leach solution before it is recycled. A cost estimate was prepared for a plant capable of producing 300 tons per day of lead, 330 days per year. The fixed capital cost on a third-quarter 1977 basis Fs $27,500,000, and the estimated operating cost without a charge for the concentrate is 4.9 cents per pound of lead product. Assuming a selling price for corroding-grade lead of 31 cents per pound and a charge for the concentrate of $332 per ton, the interest rate of return on investment after taxes is 16 percent. The leach-electrolysis process, therefore, appears to be economically attractive under the assumed market conditions.

Jan 1, 1978

By K-H. Frohne

This report presents a study of the Cooper sand of the Fork Run pool of Warren and McKean Counties, Pa., and a prediction of the secondary oil recovery by gasflooding the reservoir. A computer program employing a modification of the Craig, Geffen, and Morse secondary recovery calculation was used to make the gas flood performance forecast and is presented in the appendix. The Cooper sand reservoir in the Fork Run pool lies at a depth of about 1,900 feet and covers an area 1/2 mile wide by 2-1/4 miles long. Original oil in place is estimated to have been 8,266,000 STB. The primary recovery mechanism is solution gas drive, and ultimate primary recovery may reach 20 percent over a well life of 90 years. Two computer predictions were made for gas flooding the Cooper reservoir. The first was for a 25-acre pilot five-spot utilizing existing wells, but project economics were poor since only 25 percent of injection gas is utilized for pilot oil recovery. Recovery was 71,000 STB, or 22 percent of oil in place at flood initiation, but required 25,700 scf gas injected per STB of oil recovered. In the second prediction, pilot area performance was projected for the entire Fork Run pool, and economics became good. Recovery was 1,753,000 STB from 25 five-spots after the injection of only 6,400 scf per STB of oil recovered.

Jan 1, 1969

By Thomas E. Finch

This report is an engineering-economic evaluation of alternate methods of handling the parting between two coal seams. It consists of evaluations of parting stowing techniques applicable in a representative, thick seam western United States mine. Methods are examined for their potential implementation, and an estimated operating cost per yard of material moved is developed. The methods are of two categories castback or haulback. Haulback methods use truck haulage except With scrapers, and the castback methods are a direct stowage with no intermediate haulage equipment. Possible equipment combinations include draglines, shovels, hydraulic backhoes, bucket wheel excavators, scrapers, and front end loaders. The purpose of this report is to evaluate the effective competetiveness of the various alternatives.

Jan 1, 1975

By E. J. (Kirk) Conway

The objectives of this project were to: (1) determine the extent to which maintainability design concepts and principles have been applied to the design of underground coal mining equipment, (2) try to assess its impact on productivity and personnel safety, and (3) develop maintainability guidelines to enhance the design of new or rebuilt equipment. An equipment design review was completed at ten operational coal mines. The purpose was to identify design approaches and features that enhanced and degraded the maintenance process. Mine management, safety, and maintenance personnel were also interviewed to identify machine specific design problems. Six original equipment manufacturers were visited and the procedures used to enhance the maintainability of Their equipment discussed. Volume I of the Final Technical Report presents an overview of procedures and protocol used and a summary of the findings. Volume II includes the maintainability design guide for mobile underground mining equipment.

Jan 1, 1988

By David A. Benjamin

At the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied prospects, claims, and mineralized sites in a 43,053-acre portion of the 51,262-acre Desatoya Mountains Wilderness Study Area (NV-030-l10) in 1985. The study area, located 50 miles east of Fallon, NV, is underlain by alluvial deposits of Quaternary age and volcanic and volcanic-derived sedimentary rock of Tertiary age. No mines or recent exploration activity were identified within the area studied. The Gold Basin area, located 1/2 mile to the south has produced 982 ounces of gold and 10,086 ounces of silver. The Cold Springs area, located 1/2 mile to the west, has recently been explored for gold-silver. Mineralization at these two areas apparently did not extend into the study area, but future mining at these areas would likely impact it.

Jan 1, 1986

Under contract from U. S. Bureau of Mines, Harza Engineering Company in cooperation with Eastern Associated Coal Corporation, conducted a ground control study of two mechanized longwall panels at the Federal Number 2 Mine. The mine is located in Northern West Virginia, and the coal is mined from the Pittsburgh Coal Seam. The prime objective of the study was to collect data which will aid in the proper selection of the longwall supports system and to control the entry caving problem. Instruments installed in the mine were borehole pressure cells, convergence recorders, roof sag recorders, horizontal roof strain indicators, differential floor movement systems, and lateral roof and floor movement systems. Instruments installed on the surface, above the instrumented longwall panels, consisted of slope indicator system, vertical bed settlement probe system and shear displacement detecting system. A comprehensive surface subsidence study was conducted in conjunction with the instrumentation. In addition to the instrumentation and monitoring, special tests were conducted to determine the bearing capacity of the roof and floor rocks, in situ modulus of coal, roof and floor rocks, and response of borehole pressure cells to ground stress. Cores of coal measure rocks were collected for the physical property tests. Face observations were made to detect various roof behavior parameters under the different jack setting pressures. This report essentially describes the instrumentation work, special tests and presents the data collected.

Jan 1, 1976

By D. D. Runnells

This study focused on the chemical reactions between uranium tailings fluids and cores of subjacent bedrock from the site of the Cotter Corporation uranium mill at Canon City, Colorado. Actual and synthetic tailings fluids were forced through cores of bedrock. The pH of the effluent solutions was the dominant control on the behavior of dissolved species in solution. The pH depended on the presence or absence of calcite cement in the rocks. Calcite neutralized acidic raffinates and caused the precipitation of iron, manganese, aluminum, and possibly uranium. Chloride, sulfate, and sodium were not retarded upon passage through the cores, and sulfate and chloride should be useful as tracers of escaping tailings fluids. Zinc, copper, cobalt, nickel, uranium, and vanadium exhibited high mobility under acidic conditions and were strongly retarded at elevated pH. Calcium was released due to dissolution of calcite and ion-exchange. Magnesium was not retarded in concentrated solutions, but showed moderate retardation in dilute fluids. Potassium and ammonium both showed early retardation followed by breakthrough and mobility. The behavior of molybdenum was strongly dependent on pH, with retardation at low pH and mobility at elevated pH. Selenium was highly mobile under all conditions. Selenium should be a better tracer than molybdenum for many situations. Precipitation of carnotite appears to control the solubility of uranium and, possibly, vanadium. With the exception of the precipitation of aluminum and silica, all reactions were rapid.

Jan 1, 1983

1. Domestic Production and Use: In 1980, 13 companies operated 33 primary aluminum reduction plants, with 3 firms accounting for 62% of production. Washington, Oregon, and Montana accounted for 30% of the total production; Texas, Louisiana, and Arkansas 19%; Tennessee, Alabama, and North Carolina 15%; other central and eastern States 36%. Based on published producer prices output of primary metal in 1980 was valued at over $7 billion. Aluminum consumption by 25,000 firms was centered in the East Central United States. Packaging accounted for an estimated 26% of domestic consumption in 1980, building 22%, transportation 21%, electrical 12%, consumer durables 7%, and other uses 12%.

Jan 1, 1981

By G. W. Jones

In a previous report'/ results were given and a method outlined whereby from a knowledge of the composition of the natural gas and of the inflammability limits of the individual constituents composing the natural gas, the limits of inflammability of natural gas and air mixtures could be closely calculated. This method is based on the application of Le Chatelier's law as modified by Coward, Carpenter and Payman,5/ to apply to a mixture of any number of combustible gases. This law must not be used indiscriminately, because many exceptions have been found. For example, when ethylene, acetylene, hydrogen sulphide, or chlorinated hydrocarbons are present the law may not hold. For a discussion of the many exceptions which have been found, reference should be made to a report by Coward and Jones.6/

Jan 1, 1933