Search Documents

By Paulo Couceiro, Manuel Lopez Cano

"The Panama Canal is one of the most important engineering projects of the modern era and plays astrategic role in the global economy and international maritime trade since its inauguration in 1914. Now, a little more than one century later, the final phase of its expansion program, the largest infrastructure works undertaken since its inauguration, has concluded. This expansion program has created a new lane of traffic along the Canal with the construction of a new set of locks – one on the Pacific side and another one on the Atlantic side -, increasing the Canal’s capacity and its impact on the world’s economy even more."

Jan 1, 2017

By Andrew Wetherelt

Blast vibrations are of paramount importance in a society where ever increasing development is putting more stringent requirements on their control. Increasing civil development and more complex extraction scenarios make the trade off between proficient vibration control and productivity difficult to ascertain. Historically, reduction of induced vibrations levels was achieved through a reduction of MIC’s leading to smaller but more frequent blasts in order to meet extraction targets.

Jan 1, 2007

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In-hole detonation pressure measurements are unusual in the production environment of a mining operation, partly owing to the hostile conditions to which recording equipment and pertinent probes must be subjected and, partly by the constraints of the production cycle. In recent decades, detonation pressure measurement techniques have been developed using low carbon resistors (LCR)-based gauges. They are cheap, relatively easy-to-operate, robust and with a high percentage of success in both open-pit and underground mining. Detonation pressure measurements are extremely important when carrying out numerical modelling to simulate explosive induced vibrations, since simulation results are highly dependent on the pressure-time history applied on the blasthole wall. Analytical equations have typically been used to model the pressure-time history; however, they usually do not adequately represent the behaviour of the explosive in terms of: peak pressure reached, rise time, mean frequency, decay and shape of the signal. Experimental records may be directly used instead of utilizing synthetic signals if they are available. In this work, (LCR)-based gauges are used to measure detonation pressure inside a production blasthole. The operation principle of the gauges utilized and the instrumentation layout is described in detail. A flexible resolution USB oscilloscope with high sampling rate has been used to catch the elusive pressure peak event. Measurements were carried out in production blasts fired with ANFO (0.86 g/cm3) in an underground mine––this also includes velocity of detonation (VOD) records––. A procedure based on the shock impedance matching has been developed to calculate the detonation pressure due to the characteristics of the gauges prevent its direct measurement. Detonation pressures obtained range from 1.71 to 2.97 GPa (248.01 to 430.76 ksi) which are in line with pressures calculated from the VOD records. Mean frequency and rise time analysis shows that 2 of 3 signals cannot be described using typical analytical equations.

Feb 6, 2023

By K. Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics (hereafter “the company”) developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1ms increments up to 1500ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits

Jan 1, 2024

By Joseph Indeck, Seokbin Lim, Andrew Thompson

In the design of explosively driven penetration devices, understanding the impact conditions between the explosively propelled penetrator and the target is one of the most important steps in optimizing the performance of the device. These impact conditions are especially prevalent when a shaped charge jet impacts concrete, which is not an ideal target material. The specific impact conditions, including but not limited to the impact angle and jet properties, create a great deal of variability that affects the performance and penetration of the shaped charge. The large amount of impurities and voids in concrete, along with its heterogeneous nature and the general strength characteristics, make concrete a non-ideal material for shaped charge jet penetration. These material characteristics lead to a highly non-linear deformation behavior of the concrete target during a hyper-velocity impact.

Jan 1, 2011

By Joshua Hoffman, William Chad Wedding, Braden Lusk

The University of Kentucky employs an explosively driven shock tube in the course of experimentation. A good deal of the work completed relates to the verification of blast mitigation products and strategies. The work is dependent upon reliably reproducing specific pressure time histories called out by the test in question. The facilities are located in the workings of an underground limestone quarry in Georgetown Kentucky. As such, the temperature maintains fairly consistent 60°F (15.6°C), making it a comfortable work environment year round. Unfortunately, the relative humidity follows the prevailing weather conditions allowing a wide variation, especially between the winter and summer seasons. A study was undertaken to gauge the influence of relative humidity on shock wave generation, including the positive and negative phases of the wave.

Jan 1, 2011

By Jorge Cárdenas, Gustavo Huerta, Regina Rocha Oriundo, Miguel Angel Humpire, Johan Salas Flores

Currently a critical activity for slopes stability and safety in mining is pre-split blasting to reduce damage from trim blast. Most common explosive used are based on packaged explosives, with 1 ½ in diameter cartridges initiated by detonating cord. Traditional loading process requires a significant amount of trained personnel, which in our application context could take up to 20 blasters. When pre-split blast is scheduled, it usually reduces the availability of the blasters on the total loading services at site which are also demanded to have production blasting ready at same 12-hour shift daylight time.

Feb 6, 2023

By Anderson Meireles, Leonardo Soares Chaves, Raul Carretero Hoz, Carlos Eduardo Soares Feliciano, Renato Jacome Costa

The large iron deposits in the northern region of Brazil located in the Amazon Craton have in common the presence of natural cavities. These cavities primarily occur in the upper layer of the ore body, formed above hematite mineralization. Their origin remains a topic of debate, often associated with hydrothermal drainage processes and erosive evolution. Over time, these cavities have become integral to the local environment, each contributing to the regional ecosystem of fauna, flora, and the significance of speleothems found within them. Managing these cavities poses a significant challenge for iron mines in the area. On one hand, they must preserve the cavities from anthropogenic actions, while simultaneously handling heavy equipment and large volumes. In 2023, the development of the mine took place towards the cavity under study, revealing systematic deviations in vibrations recorded during nearby detonations as the blasting got nearer. To address this, a work plan was put in place, emphasizing a straightforward approach: constructing lithology-specific vibration models, defining charge abacuses, and optimizing timing to reduce charge amplification. Implementing this methodology significantly improved adherence to the vibration limit, resulting in an around 50% reduction in standard error. This paper presents the consolidated work that allowed mining activities to continue in the area through controlled blasting, effectively mitigating potential anthropogenic damage in sensitive areas.

Jan 21, 2025

By Cary Moffat, John Kita, Rick Walker

The Lac des Iles Mine, in an isolated area of NorthwesternOntario is a relatively new open pit platinum and palladium mine. They were encountering problems with the equipment and production scheduling when ramping down to begin production on the subsequent benches. A co-operative effort between Lac des Iles Mine operation people, ICI Explosives, and the mines drilling and blasting contractor - Consbec Inc., resulted in a decision being made to use full depth sinking cuts to provide access to the next bench.

Jan 1, 1996

By Dipankar Gorain, A K. Vishwakarma, Vivek K. Himanshu, Murari P. Roy, Shubham Singh, R S. Yadav

The industrial establishments of a power plant consist of many important structures viz. cooling tower, wagon tippler, track hopper, plants and offices. The leveled foundation is the utmost need for erecting these structures. The leveling of the foundation is done by rock excavation, when the establishments have to be setup in hilly/rocky areas. Drilling and blasting is the cheapest and most dominant method of rock excavation. However, this method has associated hazards in terms of blast induced ground vibration, air overpressure, flyrocks etc. The foundation work and erection of the industrial buildings are done in parallel to achieve the faster construction of the establishment. The challenges to reduce the induced hazards in such cases are more. This paper presents a case study on the controlled blasting method devised for the rock excavation for construction of 2 × 660 MW Obra-C thermal power plant. The foundation work for this power plant was made by excavation of Dolomitic rock. The excavation work was performed in the proximity of the existing residence of the local people and Obra market. With the advancement of project, the excavation was also performed in the proximity to the ongoing construction work of various industrial buildings. Accordingly, the controlled blasting pattern was devised suitable to the specific sites. The pattern consisted of variations in blasthole diameter, burden-spacing, maximum explosive charge per delay, total explosive in a blasting round, initiation system and direction of initiation. The suitable muffling arrangements were also used, when the blast was conducted in the close proximity to the structures. The initial blasting pattern was established by analysis of blast vibration wave propagation characteristics. Thereafter, the final pattern was adopted for the safe excavation at the site. The safe excavation for the foundation work of this power plant has been completed successfully based on the devised controlled blasting pattern.

Feb 6, 2023

By Jesus Pascual, Benjamin Cebrian

A new Convention Center is going to be built in the millenary city of Toledo, right in the old city limits. The workings will need to excavate some 80.000 cubic meters of granite, which has, a trench-like structure already blasted for the construction (60 years ago) of a parking lot and a shopping area. Surrounding this trench, some few feet away, there are structures and buildings from the 16th century and remainings from previous times that need to be preserved from any damage caused by blasting. Because of this, a vibration analysis was designed according to the special characteristics of this work. Structures to monitor were located at several levels. It considered three different directions of study in order to evaluate the impact of vibrations of the structures located at three different heights of the granite trench. On top, the historical convent of Santa Fe, with some remaining from the 8th century (Muslim domination of the Iberian Peninsula), on the bottom, the Justice Hall of Toledo with 16th century walls, and, in the middle, a wall and a tower from times of the king Phillip II (16th century, the time of the Spanish Empire).

Jan 1, 2004

By Stephen Mansfield, Saran Sankar

The Sentinel open pit copper mine, operated by First Quantum Minerals Ltd, is located in the North West province of Zambia. The Sentinel orebody is a sediment-hosted, structurally modified deposit in which mineralisation is contained in the phyllite formation, which occurs as a series of layered, continuous sheets having a northerly 20 to 30⁰ dip. The persistent nature of the geological structure can lead to the generation of large slabs when joints are relatively close together or very large blocks when joints are more widely spaced. With standard blasting methodologies, the challenging fragmentation most commonly occurs in the stemming zone and blast interfaces, reducing excavation rates and increasing the risk of crusher bridging events and reduced throughput. A generalised approach to increase powder factor would increase in drill and blast costs and would not be sufficient to target the specific cause of the challenging fragmentation. Implementing differential blast energy based on post blast requirements for different material type, such as ore and waste, and rock mass characteristics is not new in the mining industry. High-energy blasts for ore aim to produce finer materials, enhancing downstream processes such as crushing and grinding, while reducing power consumption and increasing throughput. Conversely, waste rock often requires less energy in order to deliver optimised fragmentation for loading and hauling efficiency. Identifying and applying optimum blast energy to specific material type and geological domains will not only ensure smoother and efficient operations throughout downstream processes, but will have a direct impact on overall profitability of the entire operation. This paper will describe the methods used to model and implement differential blasting across a range of material types in order to deliver the required blast outcomes for ore and waste and the impact on downstream processes and drill and blast unit cost.

Jan 21, 2025

By Donald Wagstaff, D. Scott Scovire

The Coeur Rochester Mine is the largest primary silver surface mine in North America. Throughout its 17-year life, gold and silver grades leaving the tertiary crusher have typically been, on average, slightly below the mined bench grades as determined by blast hole assays. On a project-to-date basis, this grade variance is well within industry standards. While these variances are acceptable, mine personnel continue to study ways to further minimize the grade differences. One suspected cause for lower than expected head grades are ore loss and dilution resulting from blast-induced shot movement. In regard to grade control, the underlying design principle for non-electric blasts is the generation of uniform movement of the blasted rock material. Using one or two uniform directions of initiation, ore control methods at Rochester currently include adjusting flag lines on the muckpile in an attempt to account for displacement from original, pre-blast locations. To improve upon standard non-electric blasting practices, a series of evaluation blasts using an electronic initiation system (Orica i-konTM) was conducted in the summer of 2002. The primary objective of the evaluation blasts was to design shots that would segregate the ore and waste blocks into distinct muckpiles. Due to surface delay burning front limitations, truly effective ore and waste segregation blasting is difficult to accomplish with non-electric initiation systems for all but the most basic of ore geometries. The electronic detonator evaluation blasts produced visible boundaries in post blast muckpiles, identified by troughs or low areas, that closely matched the actual locations of pre-blast ore control flag lines based on blast hole assays. By blasting the ore and waste into distinguishable piles that were flagged and excavated accordingly, it is believed that blast-induced ore loss and dilution was reduced.

Jan 1, 2004

By Sunil Vytla, Akash Adhikari, Purushotham Tukkaraja

Blasting operations produces gases and fumes that may be toxic or non-toxic in nature. A detonation of commercial explosives such as ANFO, emulsion, and dynamite would ideally produce only nontoxic products such as steam (H2O), carbon dioxide (CO2) and nitrogen (N2). However, in the real world, the detonation of explosives produces toxic products such as nitrogen dioxide (NO2), nitric oxide (NO) and carbon monoxide (CO). The focus of this study is the blast fumes entrapped in the muckpile. Fume clearance and workplace re-entry time studies performed in the past have overlooked the toxic gases entrapped in the muckpile. Studies show that as much as 60% to 70% of the fumes or gases produced during blasting underground can remain entrapped in the adjacent rock mass or in the muckpile. The toxic fumes trapped inside the muckpile are slowly released and could be fully uncovered during the mucking process. Exposure to these gases or fumes is hazardous to mine workers. In this study, author have analyzed the nature of fume flow, i.e. accurately predicting where and how the fumes flow after an underground development/tunnel blast. This will help in determining i) precise re-entry times for the workers ii) rate and direction of the fume flow. Computational Fluid Dynamics (CFD), a mathematical simulation technique that predicts fluid dynamics phenomena is used for this purpose. CFD is preferred over physical models because it is inexpensive, once the accuracy is established, a wide range of scenarios can be simulated quickly, and the toxic gas flow patterns through underground openings can be analyzed efficiently. For this study, CFD is performed using SC/Tetra software owned by MSC software company.

By Andreas Gaich

A new 3D fragmentation analysis method for muck piles is presented. It works with aerial imagery from UAVs (drones) and handles entire muck piles with minimum user intervention.

Feb 1, 2020

By Tristan Worsey, Nathan Rouse, Evan Thibaud

Electronic detonators allow for variability and accuracy with blast delay selection and timing sequence. However, a single published guideline for selection of electronic timing delays is not available on the OneMine database. There are published documents that present options for timing with electronic detonators, some of which provide great detail and scientific evidence, but there is no single document that presents several different approaches with simple instructions on how to apply the various timing approaches. This paper reviews published electronic timing approaches and results, then presents guidelines for electronic timing for alternative mining methods, which include: bench blasting (ie. quarries) and crater blasting (ie. metals mines). Most of the approaches are based on calculating milliseconds per meter for rock types, as quantified by the rock sonic velocity. Guideline calculations are provided for recommended hole-to-hole delays and row-to-row delays for both free-faced bench blasting and crater blasting approaches. These are the two most common blasting methods for mining operations. Typically, free-faced bench blasting is the approach used in quarries with a bench height to burden ratio of around 4, and crater blasting is typically used in large blasthole diameter/short bench blasting in metals mines with a bench height to burden ratio of around 1. Mines may focus on fragmentation, mucking rates, ore movement distance and movement direction. Recommendations are also included to provide general recommendations based on a mine’s preference for movement and fragmentation. References include twelve studies on bench blasting and six studies on crater blasting. In addition, a discussion is included on the application of these recommendations at a full-scale surface gold mine.

Jan 21, 2025

By David Harrison

The Charleroi Locks and Dam (Figure 1) was completed in 1932 and is located on the Monongahela River, approximately 22 miles (35 km) south of Pittsburgh, in Charleroi, Pennsylvania. It is comprised of a 420 foot (128 m) gated dam, and a 720 foot (219 m) by 56 foot (17 m) land side lock which provides for a 16.6 foot (5 m) vertical lift.

Jan 1, 2015

By Glenn Tobin

The overarching goal in modern drill and blasting operations is that of optimising mining operations to achieve higher levels of productivity, safety, profitability and sustainability. Air decking, a technique used in drill & blasting to optimise explosive product use while achieving a target rock fragmentation1, is a technique that when executed correctly is proven to achieve consistent results independent of rock strength and the position of the holes (single, multiple, vertical, slanted), as well as being proven to reduce super-fragmentation (under-size or fines) while able to achieve optimal fragmentation, especially in the stemming zone2. The ‘shock absorber effect’ if the air deck reduces ground vibration and air blast3. Additionally, the practice of loading explosive product directly in saturated ground without dewatering or lining prior is an increasing global trend.

Jan 1, 2012

By Jan Westberg, Roger Holmberg, Bernt Larsson

Over the last couple of decades there has been an increased demand from the market for precision detonators, partly because of a need for better blasting results and partly because of a need for better vibration control. Today's detonators have a pyrotechnical delay element which gives a relatively high time scatter, increasing with the length of the delay time.

Jan 1, 1988

By Lazar Kricak, Vladislav Kecojevic, Dragan Bogunovic

In spite of many advantages explosives have, their usage may cause environmental problem such as seismic vibration. One of the solutions to this particular problem may be application of an artificial screen as a barrier to the seismic wave path. This paper presents the results of experimental research on the artificial screen concept, its characteristics and role in attenuation of seismic effects generated by blasting. More than 1,500 laboratory measurements were conducted with different combinations of screen sizes, positions of the screen to blasting source, and intensities of blasting impulses. The results of the study show a significant reduction of generated vibrations by employment of artificial screens.

Jan 1, 2007