Search Documents

By Catherine T. Aimone-Martin, Kristen Kolden

In August of 2013 the USDA Forest Service (USFS) blasted bedrock at the base of a waterfall in Kanalku Creek within the Kootznoowoo Wilderness Area on Admiralty Island in the Tongass National Forest located in Southeast Alaska. The purpose of the blasting was to widen and deepen a plunge pool at the base of a waterfall complex considered to be a partial barrier to migrating sockeye salmon. Drilling and blasting to remove 12 to 15 cubic yards of rock occurred over a two day period.

Jan 1, 2015

By T Duff

This paper describes results from small scale tests conducted to determine the distribution of pressure on target plates when subjected to loading due to the detonation of a buried mine in various media. The tests are conducted by using saturated sand, dry sand, and water as the loading media. Different stand-off distances are investigated. Kolsky bars and pressure sensors are used to determine the free-field pressure - time profile of the output of the charge at any location on the vehicle bottom. For verification of the pressure results at certain distances, the specific impulse measured by utilizing different size round plates are employed. In order to investigate the loading mechanisms, high speed cameras are applied. The small-scale test results can be scaled to full scale by using verified scaling laws.

Jan 1, 2014

By Michelle Crull, Susan Hamilton

Explosives safety requirements in the United States began in 1909 when the American Railroad Institute questioned explosives manufacturers regarding distances necessary to protect employees and property. In response to this inquiry, a group of explosives manufacturers collaborated to study over 200 explosive accidents. This study resulted in the 1914 American Table of Distance (ATD) published by the Institute of Makers of Explosives (IME). The 1914 ATD provided suggested separations between explosives and inhabited buildings, public highways, and public railways.

Jan 1, 2010

By John Tatom, Michelle Crull, Robert Conway

The US Department of Defense Explosives Safety Board is sponsoring the development of a risk-based explosives safety siting program, SAFER. The fragment and debris hazard generated at the potential explosion site (PES) is critical at an exposed site (ES) over a significant range of standoff distances. The Science Panel Impact Debris Evaluation and Review (SPIDER) test program has been planned to develop improved predictions for the hazards inside an ES by fragments and debris. Data will include the mass and velocity required for perforation of the test cross-section and the characteristics of all debris produced inside the ES.

Jan 1, 2010

By Weiying Zeng, Shouwei Wang, Jinbei Zhong, Xiangdong Meng, Lingtian Meng

"Due to a drainage problem, the Lanzhou to Chongqing high-speed rail line had been out of service during the 2015 wet season, so a drainage tunnel is to be constructed for the line and required to be accomplished before the 2016 wet season. This drainage tunnel is only 5 meters below the line which is in service, therefore blasting vibration needs to be strictly controlled. This paper introduces all theapplied blasting methods, parameters and detonation throughout the entire project, finally bringing in the electronic detonator stagger phase technique and corresponding time difference for detonation."

Jan 1, 2017

By D. S. Preece, S. Silling, A. Bhuiyan, C. M. Lownds

GEM (Geologic Element Motion) is a Discrete Element Method (DEM) capability for blast-induced heave simulation with a very fast computational algorithm that can efficiently treat many different element shapes by utilizing alternating arcs and lines. GEM calculates rock motion from a knowledge of the gas pressure moving the elements. This requires an expression for the pressure vs volume, or the adiabat, of the explosion product gases. This work uses an analytical expression for the adiabat derived from the explosive’s properties. The effect of the explosive detonation pressure in crushing an annulus of rock, and setting up a shock wave, is termed Brisance. GEM incorporates a working hypothesis for the deleterious effect of Brisance on subsequent rock motion.

Jan 1, 2024

By Tom Snyder, John Brulia

Part I is the first of a series of articles by the authors on hazardous materials (HM) transportation safety and compliance for shippers and carriers who offer and transport commercial explosives in commerce on public highways in the U.S.

Jan 1, 2014

By A. Ravi Kumar

A trench is a structure to accommodate fluid carrying pipelines for water, gas, petroleum products etc. Trench serves the purpose to haul the fluids in bulk over long distances safely and economically. Use of pipeline for moving oil and gas was essentially a post World War II development, but now it has acquired its own importance.

Jan 1, 2008

By M. S. Dotto

The knowledge of the explosive/ rock mass interaction process is important in predicting blast performance. It includes understanding rock properties, energy usage, and attenuation in the rock mass. The paper proposes a method to quantify blast-induced rock mass damage from the field measurements and apply it to modeling blast fragmentation.

Feb 1, 2020

By Lon Santis

This paper analyzes 110 serious accidents that occurred during the use of commercial explosives in mining, construction, and other industries since 1992. Data from the Mine Safety and Health Administration (MSHA), the Institute of Makers of Explosives (IME) members’ reports, and media reports were used. Only accidents that resulted in a fatality, significant lost work time, or injury to the public were considered in this analysis. The accident data were analyzed for trends in frequency, type of industry, cause, type of individual harmed, and geographical region. Although the data showed that explosives accidents are decreasing in frequency, still, 29 people were killed and 134 injured. Eightyfive of the accidents occurred in mining, 17 occurred in construction, and 8 occurred in other industries including oil recovery, seismic exploration, agriculture, logging, boiler cleaning, and avalanche blasting. As other studies have shown, flyrock and failure of blast area security caused over half of the accidents. Mishandling, misfires, or fumes caused just over one-third of the accidents. Lightning and drilling into explosives were responsible for the remainder of accidents.

Jan 1, 2003

By Adrian J. Moore, Alan B. Richards

Responsible blasting requires that rock throw be controlled to ensure that no danger will result to people and property. This paper describes the development and testing of empirical field calibrated formulae that can be used to evaluate rock throw, provide an early warning of when reduced burden will endanger people and property, and prevent flyrock incidents. Inputs to the formulae are charge mass, burden or stemming height, and a site constant that lies within a general range that can be tightened by site calibration. The output is the distance that rock will be thrown, and this ‘design your own flyrock’ quantification can be used to establish both safe clearance distances, and the critical range of burdens and stemming heights where the situation changes rapidly from safe to hazardous. Examples are given of the use of the model to control flyrock in open-pit mining and quarry operations, in situations which are controlled by both burden and stemming height.

Jan 1, 2004

By Lynn Long

We have seen many new developments in the explosive and blasting accessory category, but one of the most useful items is the blast control plug. Blast control plugs are cone shaped units that are placed in the stemming just above the explosive load. They are placed about 8 to 12 inches up into the stemming material.

Jan 1, 1996

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Ray Slavin, Remi Proulx

The Meikle Mine is a mature underground gold mine utilizing primary and secondary longhole open stoping method with delayed backfill. Combined production with the newly developed Rodeo Mine is 4700 tons per day (4265 tonnes per day) of ore. The vast majority of Meikle Mine production comes from secondary and remnant stope blocks. Remnant stopes are ore blocks that were left behind in the initial mining sequence due to various reasons. Mining of these remnant blocks has created many challenging blasting situations. The application of electronic initiation to blast remnant stopes has proven extremely beneficial. Electronic initiation has provided the blasting engineer with a high degree of flexibility with respect to timing to successfully extract these difficult stopes. Post blast assessment of the remnant stopes using the mine’s cavity monitoring system (CMS) demonstrates that the mine is maximizing ore recovery and minimizing waste dilution. The largest remnant stope blast to date required 54 holes and produced 6700 tons (6075 tonnes) of ore. Another area where the application of electronic detonators has proved successful is in the extraction of slots in which ground conditions are extremely poor. Taking the slot blasts in one shot with double-decked holes as opposed to two single-decked shots has eliminated the need to clean and or re-drill holes. The ability to open the slots in one blast has helped reduce the total mining cost. This concept has recently been expanded to blast complete stopes in one shot. This reduces the stope cycle time considerably and allows the mine to bring ore forward. Current plans for 2004 are to excavate 50% of mine wide stope production using electronic initiation technology.

Jan 1, 2004

By Norman Paley

A blasting project was undertaken at the Teck Alaska Red Dog Mine in 2005 to 2007 to determine the extent that using electronic detonators could increase Semi-Autogenous Grinding (SAG) mill throughput. The results of that project were reported at the 2010 ISEE Annual Conference. This paper is a postscript to that project and provides the fragmentation resulting from the implementation of a 15% pattern expansion using electronic detonators.

Jan 1, 2012

By Gustavo Huerta Valer, Jorge Cárdenas Miranda, Johan Salas Flores

One of the challenges of mining is the optimization of the blasting process, which has an important impact downstream in the processing of crushed ore in the plant, that is why mining companies ensure the results of granulometry obtained from the blasting process through a joint work with companies specialized in the process of loading with explosives.

Feb 6, 2023

By Peter Moser, Finn Ouchterlony, José A. Sanchidrián

"Blast fragmentation data in the form of percentile fragment sizes as function of specific charge oftenform a set of straight lines in log(size)-log(energy) space that tend to converge on a common focal point.Single-hole shots in specimens of virgin material clearly show this and the phenomenon is called the fragmentation-energy fan. Field data from bench blasting in rock scatter much more but may be interpreted to form such fans. The slopes values of the fan lines depend primarily on the percentile level. This property can be derived from sieving functions of the form P[ln(x/xmax)/ln(xmax/x50)]. An example is the Swebrec function when the parameter b is constant."

Jan 1, 2017

By Tom C. Palangio

Commercially available online particle size analyzers (OPSA) are in their third decade of development (Palangio, T.C., 1985), (Franklin, J. A., Maerz, N.H., 1987), (Maerz, N.H., Franklin, J.A., and Coursen, D.L., 1987). The installed base of operating analyzer numbers is in the hundreds. This paper takes a look at five critically important relationships that users have discovered through the use of OPSA systems. The two key attributes of these systems are: 1) consistency and, 2) historical context compared with traditional practices.

Jan 1, 2016

By Raden Haris Handayana, Jerri Mapanta, Eri Barlian, Milia Putri, Nasfryzal Carlo, Jihan Lubis

Waste oil is a growing problem throughout industries where environmentally responsible disposal ways are usually costly. There are many industries have developed process to reuse of waste oil as a source of energy on their own premises. Hanwha Mining Services Indonesia is one of blasting service that manufacturing explosive using waste oil. The usage of 60 % waste oil content in fuel solution already developed applied since 2020 at Petrosea-Kideco Site and will be increase until 100 % in 2022. The purpose of this research is to analyze the increasing of waste oil usage from 60 % to 100 % content at Petrosea Pit without reducing the emulsion quality and performance, and surely eliminate the fuel cost and reducing waste oil processing cost. Some trial conducted to determine the effect and quality of using 100 % waste oil content on emulsion at production blast. The method use to know the quality of 100% waste oil of emulsion is by direct application on bench blast. Using Microtrap VoD recorder, explosive energy will be recorded into m/s dimension, microtrap recorder the speed of explosive detonation in line with the speed of burning wire in the blast holes. The summarized of this research present that the using of 100 % waste oil content on emulsion can be applied on bench operation with the result of Velocity of Detonation (VoD) data is 4,559 mm/s, the mean of fragmentation size is in range 65.31 to 225.62 mm, the average of digging time on 1st layer is in range 10.2 to 11.6 s and on 2nd layer is in range 8.9 to 9.5 s, and the productivity still achieve on target. The result of all parameter quality still in the standard range of Hanwha and Petrosea.

Feb 6, 2023

By Shazad Hosein, William J. Birch, Robert Farnfield, David Jameson, Catherine E. Johnson

The current and consented quarry workings at a slate quarry in North Wales {UK} intersect old long abandoned underground slate mine workings. The old underground slate mine contains the remains of World War II buildings used to house artworks to protect them from war damage. Over the past 20 years, there have been a number of roof falls in the old underground slate mine, which have damaged the buildings and make general access unsafe. From observation of the timing of these falls, they occurred in the mid 2000’s. The purpose of the exercise was to determine the possible relationship between blast vibrations experienced on the surface and those experienced on the roof of the abandoned mine caverns. Thus preventing the need to regularly monitor in the old mine workings. In order to achieve this, a rigorous geotechnical assessment of the stability of the caverns was undertaken by a fully qualified Geotechnical Engineer. Once it had been determined that it was safe to do so, 3 “MEMs based” blasting seismographs were attached to the roof, in accordance with the instruction of the geotechnical engineer. In addition, 8 “MEMs based” blasting seismographs were deployed at various locations on the surface. The trial blast comprised of 51 blastholes, with charges varying between 46kg [101lbs] and 124kg [273lbs] of bulk emulsion explosive. The blastholes were in 4 rows of holes. The blast was connected using shock tube 25ms, 33ms and 65ms delay period relay detonators. The minimum distances from the blast to the surface and underground monitoring points were 78.1m [256 ft] and 114 m [374 ft] respectively. The results from the three underground monitoring locations in terms of resultant peak particle velocity was 4.42 mm/s [0.174in/s], 3.47 mm/s [0.137in/s], and 4.69 mm/s [0.185in/s]. In line with previous research, it was determined that the underground results [when compared on a “like for like” basis in terms of scaled distance] were lower in amplitude than the surface results. In this case by a factor between 0.47 and 0.87, averaging 0.68.

Jan 21, 2025