Search Documents

By Martin L. Smith, Robert L. Hautala

The objective of blast optimization can be approached either in a qualitative sense of designing a blast which will be "trouble free", or quantitatively in the sense of minimizing overall mining costs. Blast design simulators and fragmentation models have become an accepted tool in blasting over the last decade. Numeric simulators are very useful for solving quantitative problems, but are limited in their ability to address more qualitative problems such as post-blast bench condition. Also, current blasting models are limited by the complexity of site-specific blasting and are not functionally suited to mathematical optimization. As a result a great deal of expertise is still needed in optimizing a blast. The following describes the application of an expert system approach to integrating both a symbolic model of the expertise of the blasting engineer for attaining a trouble free blast, and a numeric optimization model relating fragmentation to unit operations from drilling to grinding. Research into this application of a coupled modeling approach to blast design is being carried out to develop a modeling methodology which will provide a suboptimal design for qualitative design goals as well as minimizing blast related costs.

Jan 1, 1991

By Gungor Tuncer, Ali Kahriman, A. Kadir Karadogan, Savas Gorgun

The environmental problems arisen from ground vibration and air blast have been faced and discussed frequently in various industries such as mining, construction, quarry, pipe line etc. where blasting is unavoidable operation. Structural damage due to ground vibrations creates great socio-economic problems for mine and quarry management as well as for the people residing in its vicinity, therefore in bench blast design, not only the technical and economical aspects, such as block size, uniformity and cost, but also the elimination of environmental problems resulting from ground vibration and air blast should be taken into consideration. With the general trend towards larger blasts in mining and infrastructure excavation, ground vibration and air blast problems and complaints have significantly increased. With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision, therefore determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. In another word, prediction of ground vibration components is extremely important for the minimisation of the environmental complaints. Estimating of particle velocity and other components of ground vibration with reliable approaches will give important facilities to the blasters. Although many studies had been carried out to isolate environmental problems induced by blasting in the past, a general reliable formulae has not been established yet. Due to restrictions on the complexity of ground motion, blasting and test site factors, experimental studies are still necessary for each site to minimise environmental issues. This paper presents the results of ground vibration measurements carried out during the excavation activity for contruction of an organised industrial region located nearby Istanbul in Turkey. The major rock type is granite that is encountered at this site. Within the scope of this study, in order to predict peak particle velocity level and produce a site-specific propagation curve for this site, ground vibration components were measured for blast events during bench blast optimization studies over a long period. In blasting operations; ANFO (blasting agent), gelatine dynamite (priming) and delay detonators (firing) were used as explosives. While the parameters of scaled distance (charge quantity per delay and the distance between the shot and the station) were recorded carefully, the ground vibration components were measured by means of two different vibration monitors for every event. Then, the data pairs of scaled distance and particle velocity were analyzed. The equation of scaled distance extensively used in the literature was taken into consideration for the prediction of peak particle velocity. At the end of statical analysis and evaluations an empirical relationship with good correlation was established between peak particle velocity and scale distance for this site.

Jan 1, 2000

By Dennis G. Wright

The Minister of Fisheries and Oceans for Canada is responsible, under the Fisheries Act, for the protection of all marine organisms and their habitats. The detonation of explosives in or adjacent to fish habitat has been demonstrated to cause disturbance, injury and/or death to aquatic organisms, and/or disturbance, destruction or alteration of their habitats. The Department of Fisheries and Oceans recognizes that the use of explosives may be the most practical or cost effective method by which to complete a project and has undertaken the development of a set of guidelines that will prevent or minimize the destruction of or disturbance to aquatic organisms and their habitats while at the same time allowing scientific and industrial users of explosives to proceed with their projects.

Jan 1, 1997

By Robert C. Friend

On-the-job and "hands-on" training programs which attempt to train newcomers to blasting with instructors whose only qualification is their experience can easily miss the boat. Organized training programs which utilize competent instructors and a well developed format are necessary if we wish to provide a meaningful program of instruction, But, let's not go overboard and attempt to provide a level of training which goes far beyond the scope of the worker's duties and responsibilities, and "need to know",

Jan 1, 1980

By Scott Giltner, Allan Koski

Blasting is one of the lowest cost yet most critical parts of the mining cycle. This paper discusses the findings of an audit conducted on the blasting operation at an iron ore mine. The purpose of the audit was to review current blasting practices in order to identify opportunities for production/cost improvements. The approach taken in the audit was to observe general blasting practices, their related downstream effects and to compare current procedures to established best practices.

Jan 1, 2009

By Kenneth K. Eltschlager, Richard R. Brochu

At the International Society of Explosives Engineers Annual Conference held in Nashville, Tennessee in February 1995, a Seismograph Standards Committee was established. The purpose of this committee was to develop objective performance specifications for vibration measurement instrumentation and field use practices. It was also understood that due to geology, temperature, and moisture in the soils, it is not possible to design and build an instrument to give results which are absolutely comparable for ground vibration. It was, however, considered essential to standardize instrumentation by which vibration can be measured under closely defined conditions so that results obtained by users of seismographs are always the same within stated tolerances.

Jan 1, 1999

By John J. Ridgeway

Habits take us where we were yesterday and attitudes tend to keep us there. Until recently, little had been accomplished to improve conventional explosive energy for use offshore. But with the special requirements of the Offshore Oil Industry, and particularly in the North Sea, most equipment, products and services must be specialized as well. Previous attempts to excavate a trench for a sealine in surf areas had been impossible to accomplish. But with the application of safe, controlled explosive energy, an impossible task to accomplish yesterday has now become a reality. Explosive energy, often overlooked as a convenient and economical offshore tool, excavated a clean trench underwater for a 40" sealine at Djeno in the African Congo recently.

Jan 1, 1977

By Pat McLaughlin, J R. (Dick) Daniels

Current practice in establishing quarries in remote areas with hilly or mountainous terrain tends to the use of airtracs (or similar pioneering units) drilling horizontal holes to establish a face, followed by bench development with light excavating equipment. The authors propose the use of a hybrid coyote blast design that incorporates long-round tunneling techniques. This method would, in effect, use down-the-hole (DTH) drills to advance the drift cut to the final depth, allowing longer and more rapid drift advances, and replace the cross-cut drifts with clusters of DTH holes to achieve the same explosives distribution.

Jan 1, 1995

By David Willock, S. Singh, Michael Glogger

The efficiency of the loading system in a mine depends upon the characteristics of the muck pile, the loading machine specifications and the loading practices. The focus of this paper was to look specifically at the size distribution of blasted material, and to quantify its effects on loader productivity. A scale model of LHD was designed and fabricated to represent machines currently employed in the industry. The experiments were performed using crushed Gabbro, which was mixed in various proportions according to Rossin-Rammler size distribution to give five different characteristic particle sizes and five different size distribution constants for each characteristic particle size. The effect of the size distribution constant on peak and mean penetration forces, work done and bucket fill factor was examined. In addition, the influence of mean particle size, 80% passing size (D80) and % oversize on the penetration force and bucket load was investigated.

Jan 1, 2001

By Robert A. Cortese, Lon D. Santis

This paper describes a method of measuring continuous detonation rates using standard electronic parts, coaxial cable, and a data recorder such as an oscilloscope. Three six-volt lantern batteries or a DC supply power the electronics that cost less than $100. Included are means of showing low battery power, finding the proper voltage scale on the recorder, and test triggering of the recorder. Modifications of the circuit allow for use in the field to measure charges up to 57 meters and for use in the laboratory to measure short charges. The high resistance (8.709 Ohms/meter) coaxial cable is a mass produced, special order cable available commercially. The driver circuit delivers a constant current to the cable, and as the detonation shorts the cable, a change in circuit voltage occurs. Recording this voltage change over time allows determination of detonation rate resolute to the sampling speed of the recorder. An oscilloscope or personal computer with a data acquisition card can easily record the data for analysis. Detonation rates recorded in the laboratory using the coaxial cable and the Bureau of Mines's traditional probes are presented. The system accurately measured the detonation rates of ANFO confined in steel pipe, detonating cord, and unconfined high explosive.

Jan 1, 1996

By Gordon M. Matheson, David K. Miller

Sinkhole development in karst terrains is a serious problem and risk to facilities built in these areas. The potential for sinkholes are a function of many things including the chemistry of the underlying rock, the location of water conductive fractures and fissures in the rock, the natural fluctuation of the ground water table, vibrations from various sources and surface regrading activities. When sinkhole open near quarry operations the occurrence of these features is occasionally attributed to vibrations from quarry blasting. The purpose of this paper is to review the evidence regarding the development of sinkholes as a result of quarry blasting. In general, it has been found that sinkholes result from collapse or piping of overburden soils into cavities or caverns developed within underlying carbonate rocks that have been in existence for many thousands of years. The overburden soils in karst areas are typically clayey and as a result are not subject to densification or liquefaction as a result of vibrations. The primary cause of an increased rate of sinkhole development can be attributed to changes in the ground water table or local surface water drainage. These changes may be caused by seasonal fluctuations, ground water level lowering in drought periods, dewatering of excavations or quarries, or local changes in surface drainage resulting from grading activities.

Jan 1, 1998

By Jason Baird, Seokbin Lim

Run up is a factor in Linear Shaped Charge (LSC) cutting for which an account must be made. It occurs on the initiation segment of the charge, and the cutting performance during this period is significantly lower. Previous investigations by the UMR Explosives Group observed that similar effects occur not only with LSCs but a wide range of other explosives applications, including explosive-driven flux-compression generators. Prior to this investigation, it was believed that the main contributing factors to run up were from the combined effects of explosive run up (detonation pressure), lack of confinement at the free, initiation end of the charge, and penetrator transition from segmented pieces to a long-rod penetrator blade. As an initial step to understanding the mechanics of LSC run up, a series of investigations was performed in which the testing series was divided into several sub-categories (explosive detonation pressure run up, lack of confinement and long-rod penetrator concept) in order to reveal the effect of each on the run up. Predominantly, commercially manufactured LSCs were used for the investigation, and the entire testing was completed by the UMR Explosives Group.

Jan 1, 2006

By R M. Bhatawdekar, A I. Theresraj, H S. Venkatesh

Wadi Limestone Quarry is one of the largest captive mines of Associated Cement Companies Ltd, India. The mine management wanted to extend the excavation as close to the plant as possible for maximum exploitation of the deposit. The National Institute of Rock Mechanics and the management of Wadi Limestone Quarry carried out comprehensive investigations to evolve a methodology to control vibration and flyrock within safe limits.

Jan 1, 1999

By Charles W. Trettel

Confined explosives upon detonation produce a chemical reaction generating expanding gases that result in fragmentation of matrix a chemical to mechanical transition. A 100% energy conversion during transition is difficult, if not impossible, to achieve. There are numerous variables that affect energy transition. Although fragmentation is the most often used criteria to determine shot efficiency, the escaping energy profile provides additional data as to the efficiency of a blast. Escaping energy can also have deleterious effects in the form of ground motion.

Jan 1, 1975

By G Dean Barrett, Ed Jr Smith, Calvin J. Konya

The purpose of the project was two fold: 1. To determine whether Pyrodex, a propellant, manufactured by the Hodgdon Powder Company, could be used as a substitute for high explosives for presplitting in granite and other materials. 2. To determine if Pyrodex, a slow reacting propellant which produces no stress waves in rock because it reacts subsonically, could cause the rock to crack similar to the results achieved with high explosives.

Jan 1, 1986

By Kaby K. Kabongo

The paper is drawn from a project intended to explore a technique of prediction, control and optimization of fracture in coal induced by blasting. It evaluates the fines generated in coal submitted to dynamic loading stresses in an impact stamp mortar. The aim is to analyze a complex phenomenon of coal response to blast-generated stresses from a series of discrete simulations of shock and gas actions in controllable processes.

Jan 1, 1995

By William Clark, Rick Taylor

"Ajax Contracting was awarded the project to drill, blast and crush 100,000 tons of quarryrock for the Forest Service In Elk City, Idaho, during the summer of 1992. This projecttakes place in an area where environmental groups opposing any development in NorthernIdaho forced the Forest Service to look for road rock In any place they could get it. Theresult was that a quarry could not be developed. It was decided that rock would be takenfrom a road cut (under the guise of straightening the road) on the main artery of Elk City,Idaho making the drilling and blasting a very sensitive issue to the local truckers haulingtrees and lumber to and from a mill."

Jan 1, 1993

By P D. Katsabanis

Image analysis has been proposed to be an accurate and convenient means of measurement of blast fragmentation. The paper compares the results of image analysis to screening using laboratory scale rock piles. The muckpiles ranged from uniform distribution samples to well graded samples following the Rosin-Rammler distribution.Deviations between screened and imaged distributions were observed in most cases due to the loss of fines. Addition of fines in the system improved the result derived by image analysis considerably. It is suggested that techniques for the prediction of fines be evaluated for modifying the size distributions produced by image analysis.

Jan 1, 1999

By Omer Yilmaz Erkoc, Gulsec Uyar Aldas

Blasting techniques, which have been used for a long time in Turkey, are powerful and economical tool in producing raw material in mining, quarrying, construction .etc. industries. The development of the society within the world has resulted in a substantial increase in the scale of such industrial projects. However, the expansion of such activity has been matched by an increased public awareness of environmental issues, particularly when it occurs in relatively close proximity to residential areas. One of the most troublesome issues facing the mining, quarrying and construction industries when carrying out their blasting activities is that of ground vibration. Because, blasting induced ground vibration can reach to very far distances from the source and has the potential for damage to concern to the inhabitants of property.

Jan 1, 2002

By James Stuart

Explosive components are common in electric power distribution systems. Basically, we use explosives either to open or to close a circuit very quickly, in order to avoid electrical catastrophe. We use explosives in these important applications, because explosive materials are compact, inexpensive, long-lived, powerful, and can be triggered instantly. A lead-alloy fuse will melt when excessive electric current passes through it. A small fuse of this type melts quickly. However, a lead-alloy fuse for high current levels must be larger, and takes longer to melt. Thus, at high current levels, a lead-alloy fuse offers inadequate protection, because electrical catastrophe might happen, before the fuse melts. We need faster-acting, explosive components.

Jan 1, 2009