Search Documents

By Adrian Moore, Alan Richards

A real-time system for prediction of the effect of meteorological conditions on airblast overpressure levels has been established in the Hunter Valley Coalfield in Australia. Real-time meteorological data from continuously operating sounding equipment and a predictive meteorological model is input to an atmospheric refraction model that enables the effect of meteorology on airblast overpressure levels in the area surrounding the blast site to be evaluated. Graphical outputs from the model, which are superimposed over a scaled airphoto of the mine and surrounding area, show the extent that airblast levels will be increased. When combined with inputs that quantify the effect of blasting specifications, the airblast levels that will result in the surrounding area from the combined effect of blasting specifications is determined. The model permits those responsible for blasting to make more accurate decisions on suitable times that blasting may take place to conform with applicable airblast limits.

Jan 1, 2009

By Muhammad Yamani, Marsell Riviera, Herry Saputra, Rizky Amin

Drill and Blast processes in hot and reactive ground conditions are a severe challenge in mining, especially in the blasting process. Our main objective is safety issues without compromising the blasting outcome. Safety concerns include unexpected detonation, product damage, and misfire. However, apart from the issue of blasting safety, it is also crucial to maintain good results such as fragmentation, loader productivity, and ore dilution control. Therefore, we use a different product selection method to produce a safe and efficient blast. Pit Araren is one of the pits of the Tokatindung Gold Mine Project in North Sulawesi Province, Indonesia, classified as hot and reactive ground conditions that range from elevation of 25mRL temperature could reach to 98⁰C (208,4⁰F) based on actual measurement. The previous practice for blast holes with temperatures above 70⁰C (158⁰F) loaded with the primer that was specifically designed for hot and reactive ground conditions consisting of detonating cord and packages emulsion that specifically formulated to inhibit exothermic reaction then tied in with a combination of non-electric surface delay detonator and detonating cord initiator (short length non-electric surface delay detonator housed in plastic connector).

Feb 6, 2023

By David Kosnik

This paper describes the technology and methods deployed in the continuous autonomous remote monitoring of cracks in interior and exterior walls of a residence near a limestone quarry. The objective is to quantitatively compare crack response due to blast-induced ground motion to that induced by diurnal temperature changes, weather fronts, occupant activity, and other phenomena. The remote monitoring and communication technology developed to obtain and disseminate crack response data for this study may provide the means to mitigate the effect of public concerns about potential impacts of ground vibrations inherent in construction and production of raw materials; it is critical to address these concerns because subsequent litigation may result in delays and increased costs.

Jan 1, 2009

By W. L. Saunders

RBH Note: In the early days of drill & blast tunneling the jobs utilized large crews of drillers and muckers. Advance per round was limited (typically around four feet) but two rounds per 8-hour shift were expected, around the clock. The scene after a shot must have been chaos, with the muckers expected to quickly make space for the drill setup. Makes one wonder how much time was allowed for the smoke and fumes to clear. Note the headgear of the tunnelers.

Jan 1, 2011

By Miquel Lamadrid, Changshow Sun, Chris Johnson

To reduce blasting overbreak and improve stope stability, several new blast designs were proposed for current and future stopes. Based on the analysis of the powder factor, and the extent of damage zone, the appropriate new blast design was selected. Excellent results were achieved from the new blast design. Comparing the new blast design with the old one, the largest of the overbreaks decreased more tan two times and average overbreak reduced more than two times. The new blast design is currently applied in all mining zones in Leeville underground mine.

Jan 1, 2008

By Nan H. Lee, Christopher J. Hunter, Stephen H. Chung

Several factors affect the productivity of mining operations. The geological structure of a mineral deposit and the fragment size of blasted material are considered to be most influential. It is well known that productivity varies with mucking cycles and that this is related to the explosive energy produced by a blast.

Jan 1, 1991

By P D. Katsabanis, S Kim

A number of small scale fragmentation tests have been conducted to analyze the effects of blasting effort on the grindability of granite, granodiorite, limestone and iron ore. Powder factors were modified, post-blast fragments were screened and drop weight tests were conducted on fragments of different sizes to deliver a variety of specific impact energies. The fragmentation from the drop weight tests has been analyzed to examine the effect of impact energy and powder factor on size reduction. A consistent effect of blasting on the various fractions of the fragmentation distribution has been obtained for all rocks used. The effect of powder factor on the impact fracturing of the rocks has been expressed in a convenient relationship between progeny size, impact energy and powder factor used in obtaining the primary fragmentation. It is clear that explosives consumption affects downstream size reduction; depending on the rock, the effect can be substantial at coarser final sizes but very small in the case of grinding to small final sizes. Differences from the expected trend can be attributed to changes in blast design. As an example, the effect of in-hole collision of detonation waves is analyzed.

Jan 1, 2011

By Christian Dye

"The following paper focuses on the developing relationship between the members of theInternational Society of Explosive Engineers (ISEE), and the mining students from the BritishColumbia Institute of Technology (BCIT). During the past two years mining students and theISEE members have worked closely in developing a student chapter within the society and onFebruary 1st 2015, the first Canadian Student Chapter was recognized at the annual generalmeeting in New Orleans. This paper discusses the benefits that both the industry and studentsgain with a strong relationship. The mining students recognize the importance for filling the rolesof retiring members of the society and industry. Prior to 2015 the school had only offered a twoyear diploma program in mining and mineral exploration methods. That included a brief sectionin the use of explosives in the mining industry. In September of 2015 students were recruited forthe first ever Bachelors in Mining and Mineral Resource Engineering program. This engineeringdegree includes a full four month course in advanced blasting and rock fragmentation. Studentssuccessfully completing the diploma program will have an entry level of technical understandingin how blasting is conducted. The students successfully completing the bachelor degree will havean in depth technical understanding of explosives and rock fragmentation. Having this uniqueand dynamic multi-level program provides the explosives industry with a pool of talent that canbe used to fill positions with graduates for all levels of the blasting industry."

Jan 1, 2016

By Syed Haq, Kyle Optt, David Campo, Doug Anderson

Limitations on allowable levels of vibration from construction activities generally consider either annoyance or damage. While activities such as drilling and roller compaction primarily create annoyance, the major concern for blasting is usually damage. Many years of research have developed correlations between peak particle velocity and either threshold or structural damage. We emphasize the term “correlation” for two reasons. First, peak particle velocity is only a single-valued representation of a vibration waveform, and does not characterize it completely. Second, a given peak particle velocity by itself, even a particle velocity waveform, will not damage anything – strain does. Why not measure strain all the time? Strain is very localized, and can vary substantially over short distances, so choosing the appropriate strain measurement can be difficult. Measurement of strain is appropriate when either the behavior of a specific structural element is needed, or the overall response of a structure can be adequately represented by a well-selected strain measurement. We will discuss the appropriateness of both particle velocity and strain as deformation and damage descriptors, in general. We will also describe a specific case history, from a tunnel project in New Jersey, correlating strain with peak particle velocity. Finally, we will make recommendations for the choice of measurement type for some common situations.

Jan 1, 2004

By Leslie Taylor, W. L. Fourney, Uli Leiste

Over the past few years, our laboratory has been investigating the loading on vehicles due to the detonation of buried explosives. We have been using target plates to represent the bottom of the vehicles that were being subject to the forces from the detonating explosives. Parameters shown to be important in the blast loading were type of soil, stand off distance (distance from the surface of the soil to the bottom of the target plate), and depth of burial (distance of the charge center of gravity to the sand surface). We conducted over the first year of our work a large number of tests which looked at the impulse being applied to the plates as a function of depth of burial, stand off distance, and type of soil. Of the three parameters we found stand off distance to be most important, depth of burial to be the next most important parameter, with type of soil least important. We also found that impulse could be scaled with explosive size quite accurately and that results (for impulse) were quite repeatable from one test to the next.

Jan 1, 2008

By Ruilin Yan, Kameron Ray

This paper reports a simple approach to model the waveform change due to travel distances based on the field measurement. A linear interpolation is used to estimate the waveform at a distance from two vibration waveforms recorded at two different distances. The resulted waveforms are compared with actual recorded waveforms at the point in both time and frequency domains. It shows that the proposed method to estimate the waveform change yield reliable results. The advantages of the proposed method are that it does not require assumptions that a transfer function does and that it is based on purely the measured waveforms that are encoded with in-situ rock properties. The method could be more reliable for far field seismic waveforms and could be an approximation for near field waveform estimation.

Jan 1, 2014

By Michael Wieland

Sharp transient stress waves generated during the delay blasting of underground coal can damage unfired borehole charges remaining in the delay pattern. These tremendous stress pulses in coal bear a strong resemblance to underwater shock waves, despite differences in rise times, damping rates, and scaling relations. "Shock wave" terminology is adopted to distinguish the sharp transient waveforms propagating through the coal from the gas-driven stresses that rift the coal. Reported waveform characteristics of shock waves through underground coal were utilized to design a simulator test for rating the impact resistance of cap-sensitive explosives. Theoretical minimum borehole separations were determined for each cap-sensitive explosive from the requirement that worst-case waves hitting an unfired charge would not exceed its impact resistance rating. Rugged explosives have higher impact resistance and will function properly at smaller borehole separations. Additional work is required to verify the findings from the simulator technique and modeling relations reported here.

Jan 1, 1990

By Daniel B. Conn, John L. Floyd

PhotoSeis™ is a blast analysis method that combines the advanced technologies of high speed motion picture photography and digital seismology. When fracturing rock with the use of explosive energy, the human eye cannot detect the details of the process due to its short duration. An extended time base is required to accurately quantify the response of the rock mass to the detonation process. This time base is provided by the use of high speed motion picture cameras. The control of ground vibrations and airblast is an important consideration when developing efficient blast designs. High vibration and airblast levels can be an indication of improper design, inaccurate detonators, or adverse geology. Since many factors can elevate airblast and ground vibration, a greater understanding of the site specific response to the blast design is needed that is beyond the scope of simple seismographic recordings. By synchronizing the photographic record provided by the high speed motion picture cameras with the airblast and vibration information from digital seismological monitoring, the Photoseis™ technique can be of great assistance in controlling airblast and vibration and optimizing the use of explosive energy for rock fragmentation.

Jan 1, 1990

By Mark Roberts

Automation, data analytics and optimisation are key trends in the mining industry. Doing more, and better, while expending less resources targets KPIs around efficiency and productivity. With the explosion of data, the next step is to develop an optimal level of processes and systems to harness this data to support value-in use decisions. Typically, significant amounts of resources and effort are invested to develop realistic simulation models. However, models are frequently not integrated with existing systems, and therefore are underutilised. When we consider the specialised process of blasting, integration with upstream and downstream processes is a significant driver to realise sustained improvements and value. The application of genetic algorithms and cloud computing to solving complex mining problems has advanced over the last 15 years, in particular with mine scheduling. Genetic algorithms are unique in that they support true multi-objective optimisation, utilising population-based methods to present trade-offs between multiple solutions. Secure in-cloud processing speeds up the processing, with results delivered in timeframes that are not feasible with desktop computing.

Feb 6, 2023

By Eric Grigoryan, Wade Hutchison

An engineering study of 2,250 blasting damage claims from 1999 to 2008 in Tennessee, Kentucky, Virginia, Nevada, California, Georgia, South Carolina, North Carolina, Alabama, Arizona and Utah were investigated over the last decade and these investigations determine that blasting ground vibrations damage claims are valid less than 1.3 percent of the time. This study determined that valid blasting damage occurred as a result of impact damage associated with fly rock, air concussion stressing, instantaneous reverse stressing associated with ground vibration and crater zone soil shifting related stressing.

Jan 1, 2009

By Anders Nordqvist

LKAB operates an underground iron ore mine in Malmberget in the northern part of Sweden. Twelve different orebodies are mined today using both longitudinal and transversal sublevel caving as mining method. The town of Malmberget is located close to the mining area. The need for urban transformation, moving people and houses, is evident for many reasons. The mining methods used have inherent subsidence issues and there are also vibrations from blasting and mine induced seismic events.

Jan 1, 2018

By Robert Hopler

RBH Note: At the time of this price list the handwriting was already on the wall regarding the ultimate breakup of the company under the Sherman Anti-Trust Act. The brand names Atlas and Hercules, noted on page 3 of this pricelist, would become the names of the new companies created from du Pont.

Jan 1, 2012

By John C. Didlinger, John L. Didlinger

As we begin the pre-blast survey we need to decide on the number of holes needed for production and a detailed highwall inspection. The survey consists of checking the highwall and placement of barrier cones. At the Elmhurst Chicago Stone Company, Barbers Corner Plant, we use 18-24" orange highway type safety cones. These cones are easily noticed because of their high visibility color in all weather conditions and are placed approximately 20-25 feet from the face and approximately 50 feet apart along the highwall, then the area is checked for back break, under cut, over hang, surface filled area and clay area. This deposit is unique because of the number of clay filled areas and slip seams that meanders through the deposit plus a fault that runs North-Northwest and South-Southeast. This particular limestone deposit is overlaid with glacial sand and gravel and the top weathered stone wanders plus or minus 10 feet in 1400 feet.

Jan 1, 1996

By John L. Floyd

The use of explosive energy to displace overburden or waste material can provide substantial savings to operations which normally rely on mechanical means for material removal. To optimize the available explosive energy, it is important to quantify the rock's response to the type of explosive and explosive accessories used. During a blast, rock breakage and movement occur so rapidly that the naked eye cannot detect the details of the fragmentation process. A relatively high speed motion picture camera (500 frames per second) can provide the extended time base needed to analyze in detail the site-specific rock response to the explosive detonation. The data of importance to blast casting that can be quantified from these films includes initial face movement, trajectory of rock, and differential face velocities of the material shot. In addition, the ground swell velocities, stemming confinement, and stemming ejection velocity can be determined. The performance of explosive products and delay element accuracy can also be ascertained. The use of high speed motion picture photography and analysis can reduce the number of field trials necessary to maximize explosive performance and increase the benefit provided by blast casting, and in turn, lower production costs. This paper will discuss the methods used for data accumulation and analysis. In addition, three field studies conducted at three separate mining operations will be presented.

Jan 1, 1988

By Fumihiko Sumiya, Kunihisa Katsuyama, Yuji Ogata, Yukio Kato, Yuji Wada, Yoshikazu Hirosaki

Smooth blasting technique is widely applied for tunneling road or railway construction in Japan. However, smooth blasting technique often causes problem related to detonation failure in explosive column due to channel effect. Channel effect is attributed to the precursor air shock wave (PAS), which propagates ahead of detonation front in an air channel of borehole. PAS precompresses and desensitizes the unreacted explosive column. The failure of detonation propagation occurs as a result. It was concluded in our previous work that reducing PAS velocity was one of the effective methods for the prevention of channel effect.

Jan 1, 2003