Search Documents

By Danilo Zim, Matheus Paschoalino, Denis Guimarães, Jasbir Gill

The shortage of water supply in some regions of the globe is particularly problematic and forces mining companies to adopt alternatives like pumping sea water from the ocean up to the mining sites. Although deaeration of sea water or the use of lined pipelines are known options to prevent corrosion during pumping, a recent development of a new corrosion inhibitor allowed the use of simple mild steel pipelines for this purpose. The objective of this study is to demonstrate the recent advances of this technology in protecting against not only general corrosion but localized corrosion, main cause of corrosion-related pipeline failures. Corrosion studies were carried out using electrochemical techniques, weight loss balance as well microscopy surface analysis in order to measure and therefore evaluate the treatment efficiency. The right dosage of corrosion inhibitors may vary depending on water composition and characteristics of each system. Differences were observed depending on the sea water source. Pretreatment of metallic surface impacts the observed corrosion rate which can be as low as 3.6 mpy. The absence of pitting or localized corrosion was achieved in aerated seawater.

Jan 1, 2014

By Jerzy A. Mielczarski

The separation of albites from quartz by flotation applying the conventional HF-methods is no longer acceptable from an environmental and health point of view. Therefore, the search for a new reagent scheme without using HF depressor for separation of albite from quartz is under consideration. The flotation behaviour of ore mineral components depends on the produced hydrophobic or hydrophilic surface coverage (chemical functionalization). Currently we have excellent possibility of monitoring surface composition and structure at molecular and atomic levels at surfaces of natural minerals contacted with aqueous solutions of collectors, activators, depressants which is vitally important for the understanding of the surface chemistry that govern selective and efficient flotation. Detailed surface characterization of minerals before and after their exposition to different solution conditions was performed by the most modern spectroscopic techniques such as developed by us the infrared external reflection technique combined with spectral simulation and X-ray photoelectron spectroscopy (XPS). It is possible to monitor surface reactions which facilitate the separation process and those which bring disadvantage to selective flotation. At first we found that a small amount of ?mineral impurity? presented in natural ore could play important role in selective hydrophobization process. It was found that the pH of solution (parameter possible to control) and natural mineral impurities present in mineral samples (parameter related to ore origin) play a very important role in the separation process. Another important parameter is interaction between minerals, quartz and albite, present in aqueous solution. The limitation of flotation separation resulting from chemistry will be discussed. Moreover, the most promising scheme for separation of albites from quartz will be examined.

Jan 1, 2014

By V. Buddhiraju

Liberation of valuable minerals from low-grade ores is an important challenge faced by the minerals industry. It is necessary to grind the ore to extremely fine size in order to liberate the mineral from such ores. As it is generally difficult to produce ultra-fine particles of diameter less than 1-10 mm using traditional grinding equipment such as the ball mill and the rod mill, several new types of grinding equipment are being explored to produce ultra-fine particles. The planetary ball mill is promising in that it makes grinding to submicron sizes possible by imparting high energy to the ground powder. It consists of four pots mounted on a disc. The pots and the disc rotate in opposite directions. The high-speed rotation of the pots and the disc makes the grinding media move at high centrifugal velocities leading to high impact energy and thus improving the grinding performance. The planetary mill is currently being explored for its capability to produce ultra-fine particles on a large scale. In this context, there is a need to understand the dynamics of the ultra-fine grinding process within the planetary ball mill. Here, we address this need by studying the movement of media inside the pots and the grinding kinetics, employing both experimental and modeling techniques. The experiments were conducted on a laboratory scale planetary ball mill. The particle size distribution of the powder was monitored to allow an estimate of the grinding kinetics to be made while video images of the media profiles inside the pots were taken to allow quantification of the media movement as a function of process variables such as the media size, percent loading, etc. The population balance modeling (PBM) framework was used to simulate the kinetics of grinding while the discrete element modeling (DEM) approach was utilized to simulate the media motion. The parameters in the population balance model, namely, the specific breakage rate and the breakage distribution function were determined by fitting the batch grinding equation to the experimental data. The predicted powder size distributions were found to be in good agreement with the experimental data. The experimental results have shown that the mean size of product powder decreases as the size of the grinding media decreases. Keywords: population balance modeling, grinding, planetary mill, grinding media, grinding equation

Sep 1, 2012

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.

Jan 1, 2018

By T. Gong

Often plans to increase plant throughput provide an opportunity for optimising plant equipment and operating methods. This was the case in 2005 at TISCO Jianshan Iron Mine, when an increase in production was planned. The thickening circuit had presented a limitation to the plant throughput and operation with poor overflow clarity and underflow density. Following a course of test work by Outotec, a 53m diameter Supaflo® High Rate Thickener (HRT) was selected for the duty. From early stages of operation of the new thickener, the benefits have been dramatic, including: ? Improved tailings underflow density by 9% ? Improved Overflow clarity to less than 150ppm ? Considerably decreased the water and energy consumption as well as operation cost ? Stable and reliable operation This paper looks at this installation as a case study and compares the previous thickener installa-tion performance with the performance of the single 53m HRT.

Jan 1, 2014

By Magnus Evertsson, Haijie Li, Erik Hulthen, Mats Lindqvist

"The static and dynamic models for autogenous (AG) and semi-autogenous (SAG) mills have been studied for decades. Though the effects of mixing soft and hard ores in a mill and their interactions are not widely investigated. To develop a general numerical model for AG/SAG mills, a dynamic model has been introduced, and its capability to simulate multi component ore breakage has been examined and compared with previous publications. The simulation results show that the dynamic model can cover a range of milling conditions and is able to simulate complex scenarios with soft and hard ores. The dynamic model discussed here could provide substantial potential for the controlling and optimization of the comminution circuits. INTRODUCTION In the last decades, efforts have been devoted to studying the comminution circuit due to their high energy consumption. The energy directly spent in minerals comminution was about 2% globally in the year 2000 (Maurice et al, 2003). As one important part of the comminution process, AG/SAG mills are widely used for primary grinding in minerals processing. AG/SAG mill models include static and dynamic models (Kojovic et al, 2012; Yu et al, 2014; Yu et al, 2017; Liu and Spencer, 2004; Salazar et al, 2009). Many static models have been well validated over the past decades, but they are all based on steady state assumptions. Even though plants experience a steady-state condition under certain circumstances, it can be inaccurate to simulate the system by static models under all circumstances (Asbjörnsson et al, 2013). The advantages of a dynamic model are apparent that it provides more information and insights both inside the mill and through interactions with other machines in terms of pebble crushers, conveyor belts, screens and so on. In many mines, the multi-component grinding is inevitable, and the ratio of hard and soft components in the mill strongly affects mills operation and performance. Bueno (Bueno et al, 2010; Bueno et al, 2013) studied the effects of blending hard and soft ores in AG/SAG mills and used them to update the JKSimMet toolkit which was a steady state plant simulation software. However, due to the complexity of the particle interactions such as multi-component breakage function, appearance function, in mill transportation, there has been no dynamic AG/SAG mill models developed yet for simulating multi-component."

Jan 1, 2018

By J. Temuujin

Mongolia has some of the world?s largest coal reserves with an estimated total coal reserve of over 150 billion tonnes. At present, over 90% of Mongolian electricity is produced by combined heat and thermal power stations. The main coal deposits used for Central power system's power stations are Baganuur, Shivee-ovoo lignite type coal and Shariin gol bituminous coal. In Mongolia almost 600,000 tonnes of coal combustion by-products are disposed of in waste ponds. In this research, we have thoroughly characterized Mongolian coal combustion by-products including fly ashes sourced directly from thermal power stations and ash retrieved from ponds. It was determined that fly ashes generated from Baganuur and Shivee-ovoo coal deposits are class C, while ash from Shariin gol coal is class F (according the ASTM C618). All ash products were characterized by chemical, mineralogical, granulometrical, porosity, FE-SEM and radiation methods. Fly ashes sourced directly from power stations were found to be more suitable for manufacture of geopolymers for building materials application and zeolite synthesis than ashes retrieved from ash ponds. The adsorption and porous properties of zeolitic compounds were measured and found to be suitable for adsorption of Cr6+ from simulated tannery waste water. Keywords: coal, coal combustion by products, synthesis, geopolymers, zeolitic compound

Sep 1, 2012

By E. Emelyanenko, P. Solozhenkin, J. Yagudina, O. Ibragimova

"To recover tetrahedrite-tennantite series minerals from porphyry copper-pyrite ores by the froth flotation method, further research on thiol collectors is launched to promote the utilization efficiency of copper ores. In the present paper the adsorption mechanism of the collectors on tennantite surface has been investigated by computational modeling and FTIR-spectroscopic analysis, which have revealed that the decrease in prognosis of collector activity evaluation (PCAE) for tennantite is in the following order: BX (-0.34318), AEROPHINE 3418A (- 0.61756), AERO 5100 (-14.18857). The lower PCAE the stronger the ability of the collector to interact with the mineral surface of tennantite and form the stable complex. More kinetic reliable conditions to form suitable adsorption layer and rupture of the liquid interlayer with AERO 5100 have been observed by FTIR spectra due to decrease of the intensity and stretching and bending vibrations of water (less than 20 and 65%, respectively). In order to verify the feasibility of AERO 5100 as a collector the industrial flotation tests have been conducted. Flotation performance has improved significantly with the stadially grinding and preflotation of tennantite in intercycle copper flotation that allows to avoid desliming of the fragile mineral and minimize loss of Cu and As in tailings. The recovery of copper in copper concentrate increases by 3.9% with the grade maintained.INTRODUCTIONCopper is one of the first metals extracted and the main material of choice for different high-technology applications today. Currently 80% of the world's copper comes from copper sulfide ores. However, due to the depletion of high-grade copper ores in the world and constantly growing demand for copper, the need to develop processes and technologies to treat copper resources from additional sources such as mine tailings, low grade deposits, industrial wastes and deposits with high impurity levels such as As and Sb will continue to increase (Miller and Craig, 1983). The beneficiation processes of copper-pyrite ores consisting of tennantite-tetrahedrite series minerals are generally complex. Tetrahedrite-tennantite minerals occur as fine anhedral grains intermixed with grains of galena, sphalerite, chalcopyrite, pyrite and other sulfides (Saharova, 1966). The mineralized zones of Southern Urals, Russia deposits correspond with these ore types but tennantite-tetrahedrite series are more abundant in ores at the Uzelginskoye deposit, some samples of which contain 70% of copper in tennantite form (Seravkin et al., 1994). This deposit differs from other similar copper-pyrite ores by thin mutual ""germinating"" minerals and higher content of arsenic (up to 0.8-1 %) which create additional considerable problems in enrichment (Solozhenkin et al., 2016)."

Jan 1, 2018

By L. Kuzev

Unknown and unpopular vibrational grinding mills possibilities to horizontal working chambers have been discussed. They can be realized under normal conditions with the typical values of vibrations applied with vibrational grinding which are: vibration frequency from 15 Hz to 50 Hz, vibration amplitude to 6 mm and vibration geometry. These possibilities constantly increase involving new raw materials and processes. Vibration grinding is possible with other technological process accompanied by intensified technological processing, while the process decreases. In many cases these technological decisions are original.

Jan 1, 2014

By O. N. Mohanty, S. Mohan Rao, N. D. Rao, T. Mukherjee, P. V. T. Rao

"Tata Steel has its captive chromite resources at Sukinda, Orissa. They contain two ore types, i.e. (i) Ferruginous and (ii) Siliceous. The generation of off-grade ores is an increasing trend and simultaneously customer quality requirements are becoming ever more stringent. The ferruginous type ore also contains a considerable quantity of in-situ fines (~20% particles below 0.5 mm) that compound the beneficiation problem.In this paper, new strategies are discussed for producing additional value.added products after evaluating the present beneficiation practice in terms of changing market scenario, processing capability of the plant and ore characteristic. They would entail use of MGS - an enhanced gravity separator, for recovering additional products from plant tailings; production of ferruginous coarse concentrates (-3+0.5 mm with ~46% Cr2O3) using jigs; production of marketable grade lumpy (-40+10 mm size) concentrates from low grade siliceous ore using jigs and >2.8 Cr/Fe ratio siliceous ore fines treated in the Chrome Ore Beneficiation plant gravity circuit units and low intensity magnetic separator. The studies indicate that it is possible to recover 79-80% of the chromite, against a theoretical maximum of 82% from both the ore types, in the form of several marketable grade concentrates that would also include refractory grade."

Jan 1, 2003

By J-P Franzidis, P. O. Gyebi

"Coal-water mixtures (CWM) of concentrated fine coal may be transported in pipelines but this is influenced by both CWM rheology and stability. Here, a low viscosity is required to reduce power requirements, as well as good stability for transport and storage. The objectives of this study are to investigate the importance of surface charge, solids concentration and dispersant addition on the rheology and stability of a fine Witbank coal-water mixture (<75 m). Zeta potential, rheology and stability were measured with a Malvern Zetasizer, a AR1500EA rheometer and a static rod penetration test, respectively. Sendep 30D, Sendep 30F and Norilose 8058, all supplied by Senmin International, were used as dispersants, at dosages of between 0.1 to 0.5% dry coal (w/w). Solids concentration was varied from 10 to 58% (w/w). The zeta potential was found to be positive at low pH and decreased sharply with increasing pH to a minimum of -50 mV at pH 10. The zeta potential decreased with increasing dispersant concentration for all dispersants. The lowest zeta potential of -63 mV was obtained for Norilose 8058 at a dosage of 0.3%. CWM rheology was Newtonian at lower solids concentrations but became non-Newtonian at solids concentrations over 40% (w/w), with an initial yield stress and pseudo plastic behavior. The yield stress decreased sharply with increasing dispersant concentration for all dispersants. The lowest yield stress was obtained for Norilose 8058. The addition of dispersants resulted in significant improvements in stability. A penetration ratio of over 70% was obtained for Norilose 8058 after 10 days. In summary, the addition of dispersants resulted in a decrease in the zeta potential which increased the electrostatic repulsive forces between particles, thus improving both CWM rheology and static stability.INTRODUCTION Coal Water Mixtures South Africa’s energy economy depends heavily on coal. It accounts for about 70% of primary energy consumption, 93% of electricity generation and 30% of liquid petroleum fuels (Eberhard, 2011). The transportation of coal to export markets and power generation stations is a problem in the South African coal industry due to ageing and inefficient rail infrastructure. This problem is intensified by the long distance of coal haulage, delays in the time required to load and unload wagons, and environmental challenges related to air pollution and water contamination. Fine coal may be transported more efficiently and economically in a pipeline as a highly concentrated coal water mixture (CWM). Typically a fine coal CWM will contain 60-75% coal, 25-40% water and nearly 1% of dispersing additives (Atesok et al., 2005; Dincer et al., 2003). However, the transport of CWMs in pipelines is strongly influenced by both CWM rheology and stability. Here, a low viscosity is required to reduce power requirements, as well as good stability for transport and storage. These quantities are affected by the coal composition/mineralogy, solids concentration, particle size and size distribution, particle shape, inter-particle forces and dispersant type and dosage (Laskowski, 2001)."

Jan 1, 2018

By L. Y. Zhang

The metallic sulphides in Jinchuan Mine are relative friable and the gangue minerals suffer of wide secondary change, the overgrinding of metallic sulphides and sliming of gangue minerals are the main cause that makes the mineral separation indexes difficult to improve. So changing the process of grinding, and classification, and optimizing the particle size distribution of grinding product is the key improving the separation performance of Jinchuan nickel and copper ore.

Jan 1, 2014

By D. Chakraborty, Neeraj Kumar

"The study provides the comparative analysis of the performance of water only cyclones and hydrocyclone for iron ore fines processing at Joda Iron ore processing plant, Tata Steel. Joda iron ore deposits have higher proportion of kaolinite in the finer fractions and are meant to be separated with cyclones. The iron processing flowsheet of Joda comprises of water only cyclone for beneficiation of iron ore fines. Water only cyclones are used for the beneficiation of fines in the iron ore processing industry and have a larger cone angle compared to that of conventional hydrocyclones to enhance the density effect in the separation. They are aimed to achieve better product quality of underflow however; the desired result could not be achieved at the Joda processing plant. The water only cyclones were operating at the corrected cut-size of about 60 micron with an imperfection of 0.40 and water split to underflow was approximately 10%. The overall Fe recovery from the water only cyclones were 60%. Since the quality of fines produced from the water only cyclone couldn’t be improved, an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality. The trial results indicated better product quality with the Fe recovery of 72% at corrected cut-size of 70 microns and imperfection of around 0.29. In view of above results it was recommended to replace the water only cyclones with hydrocyclones to achieve higher product quality of about 60% Fe content.INTRODUCTION Water only cyclones were installed at wet plant, Joda to process the classifier fines where the cyclone underflow is considered as concentrate and overflow is discarded as slime. Because of the lower capacity of the cyclones 30% of the classifier overflow was bypassed directly to thickener. Apart from this the quality of fines produced from the water only cyclone couldn’t be improved further hence an attempt was made to process the fraction in the conventional hydrocyclone to achieve the desired product quality and quantity. Hydrocyclone was installed at Joda after replacing stub-cyclone and came into operation on 23rd Aug’ 2017.The process variables of water only cyclones and hydrocyclones are tabulated below:"

Jan 1, 2018

By Larry A. Cramer

"Three primary drivers are setting the trend for base and precious metal processing . they are: continued low real base metal prices, environmental concerns, and continued high prices for PGM.s. Low base metal prices are increasing the search for economies of scale and company consolidation as well as the development of some hydrometallurgical technologies. Environmental concerns are pushing for continued reductions in SO2 emissions and hydrometallurgical technologies. The high prices for PGM.s are driving major expansions and a focus on minerals processing recoveries and, to a lesser extent, reductions in the refining metal lockup.In nickel, HPAL operations on laterites have failed economically but Inco is still pursuing some alternatives. BHP-Billiton and others are developing bioleaching alternatives for nickel laterites and sulphides.Copper continues to be dominated by the hydrometallurgical and pyrometallurgical debate; new hydrometallurgical developments are being tested at several sites whilst the pyrometallurgists continue to make competitive cost and environmental improvements.Gold processing developments are dominated by the use of improved gravity recovery equipment and by the development of thiosulphate as a more environmentally acceptable lixiviant.PGM processing trends are the use of fine grinding technologies, higher power input flotation cells, and new pyrometallurgical technologies. Hydrometallurgical options for some applications are being sought.OVERVIEW The metals industry has remained under price pressure for some time; low and decreasing real prices for most metals have become an expected scenario. Occasional price spikes give some relief but invariably bring expansions and new entrants into an already oversupplied commodity market, thus leading to the continued price pressure. Technical innovation, economies of scale, and improved work systems are continually sought, so as to improve the competitive position of each individual company in such a climate; however, these developments add to the downward price pressure. In such a situation the application of scarce funds to research and development is a difficult task. Excess funding is not available in tight economic times and yet the main route to higher profits is clearly the application of technical developments to lower the cost of producing a metal commodity. Many technical centers have closed as a cost saving exercise and some have coalesced to obtain economies of scale. The Australian based AMIRA research organisation has grown to serve the R&D part of the market well in Australia and in South Africa by acting as the catalyst to form research partnerships between a number of industry players and as an administrator to direct the funding of research projects towards the various applicable research institutions. AMIRA has developed closer ties to Camiro (Canadian Mining Research Organisation) through the appointment of Camiro.s metallurgical processing research director as AMIRA.s North American based director. AMIRA is continuing discussions with MIRO (Minerals Industry Research Organisation) in regard to a merger, with a report outlining the merger proposal expected in March of 2003. Company focused research centers continue to be effective at Anglo American Research Labs, Teck-Cominco Research, Falconbridge Research center, Inco Research and some others."

Jan 1, 2003

By Deirdre Bradshaw, Cornelius Vos

"The detailed understanding of the variability in process performance parameters within an ore body forms a key aspect of ensuring that proper decisions are made with regards to the economic viability of that ore body. To gain this understanding, various tools have been developed over the years, of which the batch flotation test is the most well-known and applied technique for investigating the flotation separation of ores. In this paper, the Julius Kruttschnitt Mineral Separability Indicator (JKMSI) is put forward as a small-scale test, suitable for the characterization of the flotation separability of copper porphyry ores. It is demonstrated that the JKMSI can be a complementary technique to the batch flotation test, with the capability to further improve the knowledge of ore body variability. The response from this test has been shown to be sensitive to particle size and modal mineralogy, providing a critical link between flotation and upstream comminution activities. The trade-off between the fineness of grind and the recovery target can thus be evaluated to determine the minimum energy application required for optimal separation economics. The test is designed to utilize small sample quantities of various sizes, providing an opportunity to increase our understanding of ore variability through increased tests. This complements our ore body knowledge and combining this with efforts in comminution (Powell, 2013) provides a platform for extending the concept of flexible circuit design."

Jan 1, 2014

By P. Somasundaran

Treatment of mineral surfaces with appropriate surfactants plays an important role in mineral processing operations such as flotation, flocculation and dewatering. Recently biosurfactants, in particular, have received a considerable amount of attention because of their unique surface active properties and biodegradability. In this work we examined the performance of biosurfactants, sugar based alkyl glycosides and sophorolipid esters as reagents to control the hydrophobicity of minerals with selectivity of adsorption on mineral surfaces for flotation applications. It was discovered that n-dodecyl-ß-D-maltoside adsorbs on alumina, titania and hematite but, interestingly, not on silica. The hydrophobicity obtained is governed both by the surface coverage as well as the nanostructure of the adsorbed layer in terms of orientation of the adsorbed species. Surprisingly, even though the above surfactants are non-ionic, their adsorption was pH-dependent. We have correlated this pH dependence to the type of species on the mineral surface. Also it is shown that mixing of these surfactants with traditional ones can help reduce the carbon footprint due to synergy between the reagents and help selectivity due to antagonism. The experimental results were analyzed to get information on optimal pH and dosage conditions, for mineral surface modification. The study provides guidance for mineral treatments using biosurfactants and the potential use of these next generation reagents in mineral processing.

Jan 1, 2014

By V. E. Vigdergauz

Possibilities of the analysis of potential energy of bubble-particle interaction on the basis of extended DLVO theory are discussed. Interaction energies of mineral silica, coal and pyrite particles with contact angles from 20 to 100 degrees and air bubbles in neutral and alkaline solutions are analyzed. It is shown that for hydrophilic silica, the formation of particle-bubble complexes (either in the area of primary or secondary potential minima) is impossible due to the high potential barriers (from 6000 to 140000 kT)and low values of the attraction force. There is shown that for coal and pyrite particles the energy of interaction vs. particle-bubble distance strongly depends on pH value. Improvement of floatability of minerals by the hydrophobization of their surface by collectors leads to the eliminating of potential barriers and the formation of the stable complexes of minerals and air bubbles in the area of primary potential minimum. In addition, due to hydrophobization of coal and pyrite changing pH has practically no influence on the energy of interaction. There are discussed results of the numerical calculations of normalized interaction forces in particle-bubble systems on the nanometer distances for pyrite, sphalerite, and chalcopyrite at contact angles up to 85° in comparison with the experimental data. The values of adhesion force for hydrophobized particles of coal and pyrite to air bubbles are about 10-5 N, that indicates stability of the formed flotation complexes. Examples of using the long-range and high-energy effect of hydrophobic interactions for improving minerals floatability are discussed. There are illustrated minerals wettability changes induced by the adsorption of thiol collector and hydrophobic polymer. Possibilities of flocculation and flotation of mineral slimes due the polymer-collector hydrophobic interactions are shown. Keywords: bubble-particle interaction, contact angle, extended DLVO theory, floatability

Sep 1, 2012

By A. Muhammad, A. Abdelaal, M. EL Salmawy

"Energy is vital for economic growth and sustainable development. Greater efforts are being devoted to developing unconventional energy resources such as oil shale as an alternative promising source of oil or solid fuel supplement. The main object of this contribution is to determine the upgrade potential of El-Nakheil oil shale using froth flotation. Samples were prepared by comminution followed by sieving into different size fractions. The flotation behavior of the material and extent of cleaning was studied with respect to nonionic and ionic collectors of anionic and cationic types. It was found that the organic rich portions could not be rendered sufficiently hydrophobic by the used collectors and selectivity towards surfactant was very low."

Jan 1, 2014

By T. Lang

Clay sorbents from the North Bohemian Brown Coal Basin represent important but still some-what neglected accessory raw material. Submitted paper is concerned with relation between mineral structure, sorptive efficiency and reclamation exploitation of these rocks. Characters and localities of main clay sorbents from the North Bohemian Brown Coal Basin are shortly evaluated in an introduction. In next part, methodology of mineralogy survey for these accessory raw materials is stated, it is based on diffract analyse with D 5000 Siemens X-ray diffracto-meter. At the conclusion results are stated of mineralogy analyses from several clay sorbents. The determination of the zeolite and montmorillonite localities was accentuated. The paper presents also possibilities of practical clay sorbents utilization, especially by reclamation works.

Jan 1, 2014

By Xuliang Yang, Yuemin Zhao, Bo Zhang, Liang Dong, Cheng Sheng, Gongmin Li, Zhenfu Luo, Yaqun He, Chenlong Duan

Coal plays an important role in the primary energy consumption of all over the world. In 2012, coal reached the highest share (29.9%) of global primary energy consumption since 1970. Coal burning mainly contributes to the emission of SO2, NOX, Hg and other impurities that jeopardize the future of environment. . Beneficiation before coal utilization is the most economical and effective technology for removing the hazardous material and gangue. In this paper, a novel process of dry beneficiation based on gas-solid two-phase flow composed of the compound dry cleaning separator (FGX), the air dense medium fluidized bed separator (ADMFB) and the vibrated fluidized bed with autogenous medium (VFB) is proposed. The main equipment and the flowsheet of the united system are described in detail. Separating principle of the FGX, ADMFB and VFB devices are all based on gas-solid two-phase flow. In FGX, gassolid suspension is composed of continuous gas flow and coal powder in feed coal. Large size coal (+6- 80mm) can be pre-separated effectively, and large size gangue can be removed effectively. Moreover, - 6mm particles fed serve as autogenous medium in FGX. The probable E value is 0.13 for -80 mm raw coal. In ADMFB, magnetic powder with -0.3 + 0.045 mm size fraction and coal powder in feed coal are compound medium solids. The separation density can be adjusted and controlled according to properties of raw coal. -50 + 6 mm raw coal can be cleaned efficiently, the probable E value is 0.05. In VFB, -6 + 1 mm coal can be separated. Generally, -80 mm raw coal can be cleaned efficiently in the united system based on gas-solid two-phase flow.

Jan 1, 2014