Search Documents

By Brian Hart, Rong Fan, Roger Smart, Andrea Gerson, Ning Xu

A complete strategy has been developed for identification of the reasons for losses in recovery and/or grade, due to changes or complications in mineralogy and in mineral surface conditioning, and their subsequent correction. The sequence of methods starts with comparison of mineral phases between QEMSCAN/MLA (compositional) and Rietveld XRD (crystalline diffraction) with bulk assay reconciliation. This methodology has recently led to identification of unrecognised amorphous content (12-40 wt.%), previously attributed to crystalline phases, in the fine fraction (<35 µm) of some problematic flotation feeds. Attached amorphous silica, talc- and chlorite-like fines have direct influence on the hydrophobic/ hydrophilic ratio on value mineral surfaces adversely affecting flotation. SEM/EDS is used in the backscattered imaging mode to determine possible problems with liberation (e.g. remnant local locking), not detected in standard liberation analysis, resulting in gangue flotation. EDTA extraction is used to assess bulk feed pre-oxidation and sequential oxidation product loading through the circuit. Changes in circuit solutions are assayed with speciation modelling of precipitates and potentially adsorbing species. ToF-SIMS with principal component analysis is then used to correlate surface species with specific minerals and can be used to assess the effectiveness of specific reagents particularly collectors. This approach identifies unwanted activating species and interference with value surfaces by adsorbed hydrophilic ions, precipitates and fine particles. When the interference or ineffective reagents are specifically identified, remedial action can be targeted. This method has identified residual talc-like layers (<10 nm thick) inducing gangue flotation of pyroxene and chromite in PGM flotation. Recent case studies of application of the full methodology to losses of molybdenite at KUCC and to sphalerite activation in the Cu/Pb circuit at Brunswick Mines with remedial action are discussed.

Jan 1, 2014

By P. Latostenmaa, T. Hailemariam, M. Lundström, P. Halli

Doré process is unique way to treat precious metals in the copper electrorefining plant, since it uses anode slime as a raw material. In this pyrometallurgical process, also slag is produced together with Doré metal. However, the process is never ideal, and a part of metal is always lost into the slag. By using Doré slag as raw material for simply mineral acid leaching, some of the lost elements can be extracted and recovered, thus, increasing the sustainability and keeping metals in the circular economy loop. The Doré process itself is developed to convert almost all precious metals and PGMs in the Doré metal, leaving other elements into the slag fraction. The Doré slag consist of slag formers, such as borax and silica based minerals, but contain also traces of sealing materials. In addition, the Doré slag is rich in metals present in the anode slime, such as Cu, Bi and Sb, which are not converted into the Doré metal. There are only few published applications at the precious metal plants, where conservative grinding and flotation circuits have been utilized for the enrichment of valuable metals present in the Doré slag fraction (Godbehere, P.W., 1983; Segawa, C. and Kusakabe, T., 1996). However, the present study shows an alternative approach for the recovery of metals present in the Doré slag by hydometallurgical approach. The study focus on direct mineral acid (aqua regia) leaching of metals present in the Doré slag. The initial dissolved concentrations of Cu, Bi and Sb from Doré slag in the temperature range of 30-50 °C under oxygen purging with addition of 1 vol-% of H2O2 are presented. Chemical and mineralogical analyses were performed for the raw material, leaching residue, and leaching solutions in order to ascertain the leaching behavior of the metals of Bi, Cu and Sb.

Jan 1, 2018

By A. Singh, M. Ntlhane, V. Ross, M. Dlame

"Fine valuable particles are often lost to flotation tailings streams due to inefficient collection by air bubbles as well as passivation of surfaces by oxidation and slimes. The application of high-shear hydrodynamic cavitation devices (HCDs) to overcome this problem has already proven to be a considerable success in the industry. This paper details the results of further investigations that were undertaken at Mintek to better understand the mechanisms involved when preconditioning feed slurries in an HCD. By promoting inter-particle attrition and conditions of high shear within the reactor, cleaning of particle surfaces is enhanced as well as the formation of superfine (nano) bubbles which are believed to aid their agglomeration and subsequent collection by normal sized bubbles. In order to broaden the envelope of understanding with regard to application of the technology, rather than tailings material as investigated earlier, a Platinum Group Mineral (PGM) UG2 ore from the Bushveld Complex in South Africa was used in this study. The results of a series of batch flotation tests in a 10L Denver cell are presented, being conducted after the feed has been subjected to different methods of preconditioning. It was demonstrated that the preconditioning significantly improved the flotation kinetics of the PGMs, the optimum being obtained after around 20 passes through the reactor. This was accompanied by a much enhanced recovery-mass pull relationship and a significant improvement in the grade-recovery response. Significantly, the selectivity between the PGM and the deleterious chromite (expressed as Cr2O3) gangue more than doubled under these conditions. Modelling of the PGM data by means of the modified Kelsall model indicated that both the fast and slow floating rate constants were improved.INTRODUCTIONIt is well known that the flotation recovery of fine and ultrafine particles, typically less than 10 micron in size, is a challenge (Yoon et al., 1989; Miettenin et al., 2010). Although these particles are typically well liberated, due to their very low mass and inertia, the collision efficiency with air bubbles is low as a result of the inability of particles to penetrate the liquid streamlines around bubbles. Hence the probability of contact is often regarded as the ratedetermining step in flotation of ultrafine particles. Introducing more power into conventional flotation machines is likely to solve only part of the problem, as conventional mechanisms are effective only to a point in terms of shear and micro-turbulence. Further challenges are posed by the treatment of low-grade or oxidised tailings dump material, where valuables are passivated due to prolonged exposure to the atmosphere or slimes. Over the years, various mitigating strategies have been investigated, including the use of dissolved air flotation (Martinez-Gomez et al., 2013; Calgaroto et al., 2015), shear flocculation (Subrahmanyam and Forssberg, 1990), seed or carrier flotation (Tabosa and Rubio, 2010), sonication to clean particle surfaces (Aldrich and Feng, 1999; Newell et al., 2006), high intensity conditioning (Bulatovic and Salter, 1989; Chen et al., 1999; Tabosa and Rubio, 2010), and various electrochemical approaches such as changing Eh in order to promote formation of dixanthogen, dissolution of oxidation products by lowering the pH, activation by sulphidisation (Newell et al., 2006; Becker et al., 2014), and the use of alternative collectors."

Jan 1, 2018

By E. V. Bratygin, E. G. Dmitrieva

The aim of the research was to study the thermodynamic characteristics of high-temperature processing of ilmenite concentrate deposits "Central" in a neutral and oxidizing atmosphere, as well as its interaction with alkaline additives. The research was conducted using a scanning colonoscopy on thermogravimetrical analyzer NETZSCH STA 449 F3. A sample of the test material weighing 10 mg was placed in a crucible and heated at a rate of 10 °C/min to 1200 °C in argon or air. Studies have been conducted pure ilmenite concentrate and its mixtures with 5 % and 12.5% of sodium carbonate. The results of the analysis of the thermogravimetric curves it was found that the recovery of the concentrate carbon will come from ulvospinel, not pseudobrookite, and the reaction recovery is possible at temperatures above 900°C. While removing produced in the decay ilmenorutile of iron oxides in an inactive form, for example, iron (III) oxide, it is possible to reduce the quantity of the solution of ilmenite formed during the restoration of the melt anosovite. The analysis of data obtained during heating of ilmenite concentrate with sodium carbonate in concentrations of 5 and 12.5% transition pseudobrookite in ulvospinel is missing, it just breaks down into hematite and titanium oxide, which, in turn, react with N?2??3. It should be noted that increasing the concentration of sodium carbonate in the sample contributes to more complete interaction of iron oxides and N?2??3 with formation of ferrites of sodium. This can ensure full recovery of iron oxides in the concentrate, which is part of secondary ilmenite can not be dissolved in the melt formed by the lower oxides of titanium. In addition, the increase in the content of soda in the mixture significantly reduces the temperature of the initial melting point of the slag and facilitates the coagulation of metallic iron.The obtained results were used for laboratory studies of the solid-phase sintering of briquettes from ilmenite concentrate with additives of sodium carbonate and a reducing – coal, as well as for the development of technological mode of solid-phase sintering of the concentrate with the aim of obtaining product recovery with a titanium dioxide content of more than 75 %.

Jan 1, 2018

By Leopoldo Gutierrez

Eight oil sand ores with the bitumen content ranging between 3.6 and 15 wt.% and the fines content (-44 micrometers size fraction) between 9 and 69 vol.% were subjected to the standard alkali extraction test used to measure the degree of oxidation of metallurgical coals. The results showed that there is a strong correlation between the absorbance of extracted solutions at a wavelength of 520 nm and the ratio of the fines content to the bitumen content. The latter factor is directly relevant to assessing the extractability of bitumen from oil sand ores. Bitumen extraction tests showed that the bitumen recovery decreased from 90 % to 30 % when the absorbance at 520 nm increased from 0.23 to 0.64. A comparison of the UV/visible spectra of solutions obtained from the alkali extraction tests with solutions of Aldrich Humic Acids suggest that low bitumen/high fines oil sand ores release substantial amounts of organic matter very similar, if not identical, to humic acids. In contrast, high-bitumen and low-fines ores do not release as much of the organic matter, and UV spectra of these leached substances are quite different from those of humic acids. Overall, the results show that chemical composition of bitumen in the tested ores varies greatly with ore type and oxidation, and that the alkali extraction test is a promising technique to quickly assess the extractability of bitumen from a given ore type.

Sep 1, 2012

By Alireza Javadi Nooshabadi, Kota Hanumantha Rao

Formation of hydrogen peroxide (H2O2), an oxidizing agent stronger than oxygen, by sulphide minerals during grinding was examined. It was found that pyrite (FeS2), chalcopyrite (CuFeS2), sphalerite ((Zn, Fe) S), and galena (PbS) generated H2O2 in pulp liquid during wet grinding and also when the freshly ground solids are placed in water immediately after dry grinding. Pyrite produced more H2O2 than other minerals and the order of H2O2 production by the minerals was found to be pyrite > chalcopyrite > sphalerite > galena. The pH of the water influenced the extent of hydrogen peroxide formation with greater amounts of H2O2 produced at highly acidic pH. Furthermore, the effect of mixed sulphide minerals, i.e., pyrite-chalcopyrite, pyrite-galena, chalcopyrite-galena and sphalerite-pyrite, sphalerite-chalcopyrite and sphalerite-galena on the formation of H2O2 showed increasing H2O2 formation with increasing pyrite fraction. There is clear correlation of the amount of H2O2 production with the rest potential of the sulphide minerals; the greater the rest potential of a mineral the greater the formation of H2O2. This study highlights the necessity of revisiting the electrochemical and/or galvanic interactions between sulphide minerals, and interaction mechanisms between pyrite and other sulphide minerals in terms of their flotation behavior in the context of inevitable H2O2 existence in the pulp liquid.

Jan 1, 2014

By S. Serranti

The recycling of end-of-life concrete into new concrete is one of the most interesting options for reducing worldwide natural resources use and emissions associated with the building materials sector. The possibility to realize a larger re-use of silica aggregates from old concrete, strongly contributes to reduce environmental impact (reduced exploitation of natural resources, reduction of CO2 emissions, airborne dust production, etc.).To reach this goal, innovative processing techniques, as well as innovative sensing units and architectures have to be developed. In this perspective an analytical approach, based on hyperspectral sensing techniques, is proposed, discussed and critically evaluated in order to perform an automatic quality control assessment, finalized to maintain a high standard of concrete demolition waste, from the earliest stage of recycling to the further processing stages, according to the detected in-situ demolition waste characteristics. The paper deals with the analysis and the evaluation of the problems related to the integration of this approach with state-of-the-art demolition and building processes and procedures. Keywords: end-of-life concrete, recycling, hyperspectral imaging, NIR spectroscopy, quality control

Sep 1, 2012

By Irena Grigorova

"Vermiculite is a naturally occurring mineral compound composed of shiny flakes, resembling mica. Worldwide, vermiculite has been used in various industries since 1920. When heated to a high temperature, flakes of vermiculite expand several times their original size. The expanded vermiculite is a lightweight, fire-resistant, absorbent, and odorless material. These properties allow vermiculite to be used to make numerous products, as an additive, for example to potting soil, in agricultural, construction, horticultural and industrial applications, including pesticides, insulation, potting mixes, brake pads, sound deadening materials, fire protection, paints, sealants, insulating concrete and etc. Over recent years researchers have been looking for effective economic and environmental methods and solutions for fine technological waste utilization. As a result of vermiculite ore processing large quantities of fine waste dust are formed. Until now there has been no application for this waste product. Currently this waste product is stockpiled using valuable land space, and is a potential contaminant. The paper presents the results of a study on the possibility to obtain briquettes from fine vermiculite by-product. The particle size distributions, chemical and mineralogical compositions of vermiculite were determined. It was established that consolidation of vermiculite dust by methods of briquetting and its consequent application in agriculture as meliorants for physico-chemical treatment, improves soils aeration structure and properties."

Jan 1, 2014

By P. Huang, D. W. Fuerstenau

Various factors that control the natural flotability of talc, including differences due to crystal face and edge effects, were delineated. For study of talc depression phenomena, dextrin was used as a model depressant. For the enhancement of talc flotation, dodecylammonium acetate (DDAA) was used as the collector. The interaction of DDAA with talc was assessed by flotation experiments and electrokinetic (zeta potential) measurements, from which the role of hydrophobic bonding can be demonstrated. The results presented in this paper provide useful information on how the crystal chemistry and surface chemistry control the electrical double layer, adsorption phenomena, wettability, and flotation behavior of talc in aqueous media.

Jan 1, 2003

By Juan Estrada, Mirtha Frómeta, Rubén Alcalá, Emilio Montejo, José Castellanos, Juan Berto, María Rivas

"The oxidized nickel ores from San Felipe deposit are composed mainly Smectites which gives to the pulps very unfavorable rheological .properties (cinematic viscosity and high shearing strength) for transportation processes (pumping), very low settling velocities and very low thickened pulps. These properties do not allow the preparation of high % solids, which affects the economic efficiency if a high pressure acid leach (HPAL) process is used. Pulps of close to 30% solids have very high BYS making pumping impossible. CIPIMM developed three technologies to solve these problems and to substantially increase the % solids in the pulps to be leached without a thickening step. These technologies are: • CIPIMM 2. At Preparation of pulps using additives. This method is based on the effect of some additives (inorganic salts) to improve the pulp’s properties. The use of this method allows increasing the % solids in the pulp up to 40% with good rheological properties • CIPIMM 2B. Preparation of pulps by thermal treatment of the ore previous to the preparation of the pulps. This method is based on the thermal destruction of the clays structure. Its use allows to obtain pulps with 50 - 60 % solids with excellent rheological characteristics. As a collateral effect, the Ni and Co grades increases by 10 - 15%. • CIPIMM 2C. Pulp preparation by chemical treatment. This method is based on the chemical transformation of clays, to obtain without thickening, pulps with 43- 45% solids and excellent rheological properties. The use of one of the three technologies depends on the chemical and mineralogical composition of the ores and the results of technical-economical evaluations to determine which one is the best alternative before running higher scale tests."

Jan 1, 2014

By A. Norori-McCormac

"Air recovery, the fraction of air entering a flotation cell that overflows the cell lip, is linked to flotation performance, and it has been shown through industrial testwork that operating flotation cells at air rates that yield the Peak Air Recovery (PAR) results in high mineral recovery. For operating parameters over which flotation plants have little control, such as particle size, investigating the effect on the position of PAR, and the subsequent effect on flotation performance, proves more challenging. To this end, we have developed a bench scale flotation system that runs continuously and exhibits froth behavior similar to that found industrially, allowing the study of such parameters as particle size in addition to air rate. The bench scale system comprises a 4 l baffled cylindrical flotation cell, stirred by a Rushton impeller. The concentrate is recycled back into the pulp, allowing for continuous operation. Glass beads are used as solid particles, allowing a wide range of particle sizes to be tested, with TTAB as collector and MIBC as frother. The system allows operation at air rates typical of industrial flotation systems (1 -2 cms-1 superficial gas velocity), in addition to yielding a froth that coalesces and bursts and exhibits a peak in air recovery as cell air rate in increased. Solids and water recovery is also measured. The results show that air recovery is sensitive to changes in particle size. The intermediate size distribution showed a peak in air recovery (PAR) that corresponded with the maximum solids flowrate, as found industrially. It is shown that finer particles do result in more stable froths and higher recoveries, particularly at low air rates. The effect of particle size on the position of PAR is not yet unequivocally determined from these results."

Jan 1, 2014

By Christopher Robben, Alexander Mosser

"X-ray transmission (XRT) sorting has been introduced into the minerals industry in 2006 and has found various applications in diamonds, industrial minerals and metal ore processing since. The technology offers planar projections of the atomic density of single particles similar to the principle known from airport scanners, but being capable of treating up to 150tph per metre working width. In 2010, a pilot operation using a belt-type sensor-based sorter went into production at the Mittersill mine to treat the fraction 16-28mm. After an optimisation phase, the results were superseding expectations and therefore in 2012 a bigger production plant was set up. Two XRT-based sorters are parallel in operation since. One is treating the fine fraction 16-30mm while the other one is treating the coarser fraction 30-60mm after the secondary crushing stage. The XRT sorters are operated with the objective to reject barren waste before it enters the mill and flotation plant. 105,000tpa of waste material are rejected per year and can be sold as aggregate for road construction. This means that about 22% of the run-of-mine ore are rejected at an early stage with a waste reject grade lower than 0.03wt%WO3. The installation has not only led to lower specific operating costs but also led to reduced tailings disposal in an environmentally sensitive area. This allows the mine to reduce its headgrade which allows for a longer mine life. Alternatively it is possible to produce more tungsten concentrate, which is delivered to the smelter. This article will introduce the technological principle of XRT-based sorting and will discuss the flow-sheet of the Mittersill mine. Experiences that have led to the current plant design are described as well as the impact it has on the operation."

Jan 1, 2014

By Jonas Addai-Mensah

In this paper, the results emerging from the several basic and applied studies performed to provide fundamental understanding of the interplay between clay pulp chemistry, orthokinetic flocculation performance, particle interactions, applied shear and dewaterability of fine clay mineral dispersions are presented, reconciled, and discussed. Modification of pulp chemistry and behaviour was achieved by using kaolinite and Na-exchanged (swelling) smectite clay minerals, divalent metal ions (Ca(II), Mn(II)) as coagulants and high molecular weight, anionic polyacrylamide copolymers: carboxylate substituted (PAM A) and 2-amido 2-methyl propane sulphonate (PAM S) (PAM S), non-ionic polyacrylamide homopolymer (PAM N) and non-conventional, non-ionic polyethylene oxide (PEO) as flocculants. Clear links between pulp interfacial chemistry, particle interactions and dewatering behaviour, resulting from the influence of hydrolyzable metal ion, pH, temperature, polymer structure type and shear, are established. Optimum conditions for improved, orthokinetic flocculation performance of negatively charged clay particles, reflecting faster settling flocs (>10 m/h) comprised: (i) coagulation, (ii) moderate agitation rate, (iii) shorter agitation time and (iv) anionic rather than non-ionic PAM. The optimum flocculation conditions did not, however, have a significant impact on the final sediment solid content of 20 ? 25 wt%. Further application of shear to pre-sedimented pulps improved consolidation by 5 - 15 wt % solid. Application of the findings and new knowledge gained to real plant tails? case studies for marked improvement in dewaterability through thickening is demonstrated.

Sep 1, 2012

By A. Boulton

Low molecular weight synthetic polymers substituted with hydroxyl, carboxyl or sulfonate functional groups were used to improve the flotation separation of zinc or copper sulfide minerals from iron sulfide gangue minerals in three massive sulfide ores of different mineral composition. These polymers produced significant improvements in zinc or copper grades as a result of a selective depression of iron sulfide minerals. It was shown that this selectivity was the result of preferential adsorption of the polymer on the surface of the iron sulfide minerals. The different types of interaction between the functional group on the polymers and the sulfide mineral surfaces could explain the trends observed in the flotation results.

Jan 1, 2003

By Marko Hilden

"A stochastic model of mineral texture is discussed and used to demonstrate that grain association within the intact texture has a significant effect on the liberation characteristics of breakage products. The majority of previous models have simulated texture and liberation of binary systems. This new model is able to simulate complex multi-component (multi-mineral) aggregate textures and their breakage products. Grain size distributions can be defined for each of several minerals. Mineral-mineral associations can be controlled by inserting mineral grains within grains of another mineral. Repeated Monte Carlo sampling of the aggregate is used and the liberation properties of the fragments are calculated. These are analysed to generate data in a similar form as reported by mineral liberation analysis systems, including density distributions, liberation distributions, and particle class distributions. Simulations results are presented where the model has been fitted to complex sulphide ores with four minerals. Comparison of the simulated particles and experimental data show that the model is able to reproduce similar particle class distributions as measured by QEMSCAN. The texture of real complex ores can be simulated and fitted to conventional mineral liberation analysis data. The model should provide a useful and practical means of modelling the effects of mineral texture on separation processes and in geometallurgical models."

Jan 1, 2014

By Chris Plackowski, Bruckard. Warren J., Anh V. Nguyen

"Enargite is a significant penalty mineral in the copper industry and its separation from many copper sulfides by flotation is difficult. The separation may be crudely achieved using selective oxidation techniques or through the use of pulp potential control. This paper summarizes our latest contributions to a better understanding of enargite surface electrochemistry and hydrophobicity. Oxidation, roughness, hydrophobicity and species formation on the surface of natural enargite were examined by a novel experimental approach that combines electrochemical techniques, atomic force microscopy, X-ray photoelectron spectroscopy and droplet evaporation tensiometry. It allows for synchronized electrochemical control and examination of the oxidative surface morphology, speciation and hydrophobicity of enargite at pH 4 and pH 10. At low pH, surface layer formations consisting of metal deficient sulfide and elemental sulfur were identified associated with a limited increase in roughness and heterogeneous distribution of surface species produced by initial rapid dissolution of Cu, followed by diffusion limited surface layer deposition. At high pH, a similar diffusive mechanism associated with oxidation products consisting of copper sulfate and hydroxide and a significant increase in surface roughness were established. Receding contact angle measurements showed no significant difference in the contact angle on a surface oxidized at pH 10 and the freshly polished surface. Contact angle increased from 46° on the polished surface to 59° after oxidation at pH 4. Competing effects of hydrophilic copper oxides and hydroxides, and hydrophobic species of elemental sulfur on the mineral surfaces under oxidizing conditions at pH 4, and the change in surface roughness at pH 10, contribute to the changes in enargite hydrophobicity under electrochemically-controlled oxidation conditions. Most likely, both surface species and surface roughness produced by oxidation are critical to the changes in the wettability of enargite and other sulfide minerals."

Jan 1, 2014

By Gerke Gilian, Pretz Thomas, Pehlken Alexandra

"The evaluation of health hazards within the treatment of mineral and waste materials is gaining more and more importance in industrial countries. The need to control occupational health and safety has been recognised, and regulations which describe general protective measurements for personnel provide a tool to protect their health. It is the aim of the paper to give an outlook for practical approaches to risk assessment and to present measures for exposure reduction in accordance with the state of the art in Germany.Both the treatment of minerals and of waste materials are described in relation to the risk assessment. The method of evaluating health hazards in the two industries is similar and therefore both examples are presented next to each other.The example presented in the paper is the German “Biostoffverordnung” (the regulation for biological materials) which is important for the waste treatment industry. All kinds of waste treatment facilities (like composting facilities, waste dumps, sorting facilities for packaging materials) are obliged to carry out an assessment of health hazards for a variety of working areas and working places. The possible safety requirements deriving from this regulation are presented and discussed under the aspect of biological hazards."

Jan 1, 2003

By I. Silin, H. Wotruba, J. Huben, A. Ognyanova

"With increasing shortage of raw materials, the beneficiation of ultra-fine ores will play a larger role in the near future. Many established process technologies do not yield satisfactory separation results for ultra-fine materials. Without selectivity, high-grade concentrates cannot be produced. The material at hand is a taconite which had to be ground to d(90) = 25 µm to guarantee liberation of the iron oxides. The comminution was done by High Pressure Grinding Roll (HPGR) and resulted in smooth surfaces and clear grain boundaries. This is an indication of selective grinding and mineral liberation. Further processing steps included selective desliming, magnetic separation as well as reverse flotation. INTRODUCTION During the last centuries, the processing of iron ores became increasingly important. The coarse-grained, so-called lump ores that are ready for direct usage in blast furnaces without further processing are becoming gradually less abundant. The processing of ultra-fine-grained ores, which in addition require a complex ore beneficiation due to the composition of the material, will progressively gain relevance with increasing resource shortages in the future (Arvidson, 2013). The term “ultra-fine” does not hold a precise definition in mineral processing. In this paper, “ultra-fine-grained” ores are defined by the required grind size for full liberation smaller than 20 µm. Many established mineral processing technologies do not yield satisfactory separation results for ultra-fine materials. Thus, they are limited in their application to produce high-grade concentrates suitable for sintering and pelletizing for direct reduction processes. The production of a high-grade iron concentrate (over 68% Fe) with low silica content (under 2.5% SiO2) is possible from both magnetite and hematite containing ore. In addition to the mineral processing technologies (magnetic and gravity separation, flotation), technologies for the liberation of fine-grained iron ores need to be developed and improved. In contrast to the conventional wet grinding circuit by means of tumbling mills, several future trends in dry and wet grinding and regrinding are already in use. These include technologies such as vibration mills (Palla®Mill), stirred media mills (Vertimill®), vertical roller mills (Loesche) and high-pressure grinding rolls (HPGR) (Jankovic, 2015). This study preliminary investigated the mineral processing of a low-grade, ultra-fine-grained, complex iron ore in a laboratory scale after dry grinding by HPGR to 90% < 25 µm without consideration of the grinding, milling, energy and classification cost."

Jan 1, 2018

By Emile Scheepers, Chris Aldrich, Jacques J. Eksteen

The pneumatic injection of CaC2 powder into molten iron has become a very reliable and effective way to carry out desulphurisation. The key variables that influence the kinetics of this process are the condition and composition of the top slag, the oxygen activity in the hot metal and the injection conditions. Notable injection parameters include carrier gas flowrate, reagent flowrate, lance depth and initial sulphur concentration. A one-dimensional, steady-state model for momentum, heat- and mass transfer in rising gasliquid- powder plumes was developed for conditions relevant to the CaC2 refining process at Saldanha Steel?, South Africa. Combined with a model that predicts the contribution of the topslag to the process, the overall rate of desulphurisation as a function of time was determined, thereby quantitatively demonstrating the influence of the above-mentioned injection parameters on the kinetics of the desulphurisation process.

Jan 1, 2003

By Knut L. Sandvik, Erik Larsen

Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. The future silicon feedstock is most likely not reject from the production of electronic-grade silicon. There will probably be a more direct solar-grade silicon route, excluding the electronic-grade silicon "detour". Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this. Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain.

Jan 1, 2003