Search Documents

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By P. Bevilacqua

In this paper the possibility to complete the copper recovery and to enrich in PVC a mixture of plastic granules obtained by grinding electrical cables are investigated. The recovery of a large part of the copper still present among the plastic granules was possible by means of a mechanical screening, the finer polymeric fraction was collected, at the same time. In order to complete the copper polymer separation the following techniques were employed. Counter current separation in water, static dense medium separation with zinc chloride solution and copper extraction with nitric acid and subsequent electrolytic deposition. A Tri-Flo® dynamic dense medium separator was employed in order to separate the lighter polymeric fraction, from the heavier polymeric fraction, mainly PVC. Water or a salt-water solution was employed to feed the separator device.

Jan 1, 2014

By D. W. Lui

Tangdan copper oxide deposit, the largest independent copper oxide deposit in China so far, is located in the northeast of Yunnan province, southwest of China. The ore from this deposit is characterized by: low grade, high oxidation ratio, and fine-grained disseminated, resulting in poor flotation recovery. The analysis of plant flotation data reveals that the loss of copper minerals into tailings is mainly with coarse size fraction due to insufficient liberation and fine size fractions, especially minus 10 microns fraction, which proved to be very difficult-to-float with conventional flotation. In order to improve the performances of plant flotation of this ore, laboratory flotation tests were conducted with the pure malachite, which was the principle copper oxide mineral in Tangdan copper ore deposit. The results obtained suggested that a finer grinding (up to -325 mesh or even -400 mesh) be needed to decrease the loss with coarse size fraction, and vacuum flotation is a promising way for the recovery of the fine malachite effectively.

Jan 1, 2014

By B. Tora

The new method of evaluation of grindability of hard coal and its blend is shown. Standard Hardgrove test is used as a base to work out this method. The essence of this method consists of simulation of milling process in close circuit (mill-classifier) and determination of energy consumption and quantity of product under the constant feed flow. The research equipment designed specially for this project is described New method of grindability measuring completes standard Hardgrove method withdrawing its faults: ? bigger (c.a. 10 times) and more representative sample is used; ? the milling process is carried out in close circuit (similarly to the industrial condition); ? energy consumption of the milling process is determined for three samples, which differs in grain size. The new method of evaluation of grindability of hard coal and its blend is shown. Standard Hardgrove test is used as a base to work out this method. This method allows us to determine energy consumption of the milling process. The essence of this method consist of simulation of milling process in close circuit (mill-classifier) and determination of energy consumption and quantity of product under the constant feed flow. Our results will complete the Hardgrove method and will help us to better characterise coal. At the same time investigations in industrial scale are carried out. These investigations will verify this new method. Also a new mathematical model of the milling process is being elaborated. It will be used to predict behaviour of coals in industrial conditions.

Jan 1, 2014

By Chuanyao Sun, Zhenguo Song, Aijun Ren

"Lead-Zinc sulfide ore containing carbon is one of typical refractory resource. Because organic carbon has natural floatability, it has a great negative influence on flotation of lead-zinc sulfide ores. It is difficult to obtain qualified lead concentrate by flotation using conventional reagent system. In order to reduce the influence of organic carbon on lead and zinc flotation, two alternatives, i.e., removal carbon by pre-flotation or adding carbon depressant in lead and zinc flotation, can be adopted. If the flowsheet of removal carbon by pre-flotation is adopted, the lead and zinc recovery which are lost in the carbon tailings is often higher. If conventional carbon depressants are used in lead and zinc flotation, it has a certain depression effect on lead minerals. In the paper, the ore grading 1.49% Pb, 5.73% Zn, and organic carbon 3.14% has been carried out by flotation tests. In the bulk flotation of carbon and lead minerals, Pb concentrate is only about grading 21.00% Pb. In the pre-flotation of organic carbon, it’s hard to remove most of carbon, and the loss of Pb and Zinc recovery is too much in carbon tailings. New carbon depressant BK547 and three conventional carbon depressants including sodium lignosulphonate, Fe-Cr-lignosulfonate, and dextrin, are used in comparative tests of Pb flotation, and results show that BK547 have a good depression on organic carbon, and have almost no effect on Pb flotation. Using BK547 as carbon depressant, cycle test in flowsheet of two-stage Pb and Zn selective flotation and coarse concentrate regrinding have been carried out, and results show that concentrates grading 62.51% Pb and 41.33% Zn are obtained at recoveries of 70.24% Zn and 83.58% Zn.INTRODUCTION Lead and zinc mineral resources are still the main source of lead and zinc metal. For lead-zinc sulphide ore, lead concentrate and zinc concentrate are obtained by flotation. Minerals separation by flotation is a complex process and is dependent, along with other factors, on the relative distribution of hydrophobic (e.g. collector, polysulfide, elemental sulfide) and hydrophilic (e.g. metal hydroxide) species between different particles of the same mineral phase and between mineral phases (Piantadosi & Smart, 2002; Boulton, Fornasiero & Ralston, 2003). Organic carbon has natural floatability and is often associated with lead-zinc sulphide ores. If the content of organic carbon in the ore is more, the flotation index will become worse. The main problem is that the concentrates has too low grade to be qualified grade products for sale. At the same time, the consumption of reagents is more than ordinary ores without organic carbon. In order to solve the influence of organic carbon on the flotation of lead and zinc and other sulphide ores, a lot of research works have been carried out."

Jan 1, 2018

By Hui Zhang, Fei Yang, Tong Guan, Guangqin Fu, Lihong Deng, Yuanlin Chen, Xiaotong Zhou

"For a copper-sulfur polymetallic mine in south China, the main valuable minerals were chalcopyrite, pyrite and pyrrhotite. The flotability of pyrrhotite was similar with chalcopyrite and pyrite and it was easy to be oxidized. As a result, the indexes of copper concentrate and sulfur concentrate were unsatisfactory. Furthermore, the recycling of tailings water ulteriorly deteriorated the technical indexes of copper-sulfur ore beneficiation. After a large amount of experimental studies, under the condition that the tailings water recycling rate was 100%, the copper concentrate with a grade of 22.25%Cu and a recovery of 82.46% on average was obtained for the raw ore containing 0.517%Cu, 15.94%S, 25.46%Fe on average, through using new technology “magnetic separation-flotation” and effective adjustment of parameters in the industrial test which was continuously conducted for 14 shifts in 5 days with a scale of about 75t/d. Comparing with the production indexes (the copper concentrate with a grade of 17.49%Cu, the recovery was 62.27%) during the corresponding period, the grade of copper concentrate increased 4.76%Cu, and the recovery increased 20 percentage points. Besides, the indexes of sulfur concentrate gained a considerable improvement. Currently, the new technology was adopted in the design of the new-built plant with a scale of 7000t/d of this mine. The new technology provided powerful support for the tailings water recycling and indexes improvement of copper-sulfur ore beneficiation.INTRODUCTION Chalcopyrite was usually associated with pyrite and pyrrhotite in copper-sulfur ore. Due to the similar flotability, it was difficult to obtain copper concentrate and sulfur concentrate with high grade. Furthermore, sulfide ore was easy to be oxidized and a large amount of ions formed in the pulp by the dissolution of minerals, which made the pulp become acidic. As a result, pyrite and pyrrhotite were easy to be activated in acidic solution and their flotabilities became stronger. Meanwhile, hydrophilic film formed on the surface of chalcopyrite in raw ore. The flotability of chalcopyrite became weaker and it made the separation of chalcopyrite from pyrite and pyrrhotite more difficult. So it was more difficult for copper and sulfur recovering with the recycling of tailings water containing high content of heavy metal ions and reagents."

Jan 1, 2018

By Jaeheon Lee, Jae-Chun Lee, Doyun Shin, Minseuk Kim, Hyunsik Park

"The appropriate treatment of cyanide waste water is becoming an emerging issue because of the toxic residue and large quantity produced from gold processing plants. In the present article, we designed and operated a continuous biological cyanide treatment system using domestic sewage sludge and various microorganisms including a cyanide-producing and degrading bacterium, Chromobacterium violaceum. The synthetic wastewater containing 50 mg/L of cyanide was pumped continuously into the reactor at a flow rate of 500 mL/d for 21 days. When 50 mg/L of cyanide was fed, the cyanide concentration in the effluent of the reactor inoculated with activated sludge (S-50) decreased by 7.5 mg/L in the effluent. The other reactors did not show significant cyanide degradation and the reactor inoculated with C. violaceum showed increased cyanide concentration in the effluent. The microbial community in the reactors was analyzed by 16S rRNA-gene based pyrosequencing technique to investigate microbial response to cyanide addition and operation time. The microbial community analysis shows that the phylum Proteobacteria was detected in the reactors showing significant cyanide degradation (S-50), while Firmicutes and Bacteroidetes was dominant in the other reactors with very low cyanide degradation. Proteobacteria could not compete when the other phyla Firmicutes or Bacteroidetes were inoculated. This study shows the feasibility of the biological cyanide treatment system for gold processing plants and contributes new fundamental knowledge about the microbial community in the biological cyanide treatment system. INTRODUCTION Cyanidation has been widely used to recover gold from ores or secondary resources since first proposed by MacArthur and Forrest in 1888 (MacArthur et al., 1888) and it is used in many states of the USA, including Nevada, Arizona, California, Colorado, and Idaho (Laitos, 2012). Cyanide compounds are highly toxic and create serious problems for wildlife and water management (Solomonson, 1981; Donato et al., 2007). Furthermore, because many countries have imposed strict standards for cyanide discharge (USEPA, 1985), it is essential to develop a cost-effective and environmentally friendly technology for treating cyanide-containing wastewater."

Jan 1, 2018

By B. Y. Tuo

This article presents results of studies performed to determine the feasibility of using low-grade limonite ores from Yunnan deposit. Laboratory tests and commercial trials have shown that the magnetic separation can be performed with a high high-grade concentrates. The quality of the preparation concentration meets the requirements for blast-furnace smelting. The results as a whole demonstrate the feasibility of utilizing bank limonite ore. Yunnan limonite?s magnetic separation, roasting magnetic separation and flotation experimental study shows that grade of the ore grade can been from 32.91% heighten to 58.64%, a recovery of iron is 90.87%, productive rate is 51% through orthogonal test optimization; roasting magnetic separation can obtain that the grade of iron preparation concentrate is 61.16%, recovery is 67.39%, productive rate is 36%. As far as economy and enviormental protection is concerned, strong mag-netic suggested a more appropriate process. Keywords: Limonite; Roast; Magnetic separation

Jan 1, 2014

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

"The morphology of pellet feed is known to influence several properties of iron ore pellets, including drop number, compression strength and reduction properties. The effect of grinding method on the particle size, specific surface area and particle shape of an iron ore concentrate has been studied. Grinding methods considered were ball mill and high pressure grinding rolls (HPGR). 5 different samples (Blaine= 1800, 1900, 2000, 2100 and 2200 cm2g-1) were used to compare the size, shape and specific surface of particles for each grinding methods. Particle size was meticulously examined by sieve analysis, laser sizing and image analysis. In samples ground by ball mill, it has been observed that the fraction of particles <10µm increases from 39% to 46% as the Blaine number increases from 1800 to 2200 cm2g-1. For HPGR samples, corresponding figures are 41% and 49% respectively. It is evident that for samples ground by HPGR, the fraction of fine particles is higher than that of those ground in the ball mill. To measure the specific surface area of particles, Blaine and BET were used. A higher real surface area was observed from HPGR treatment in comparison to ball mill grinding, provided by a higher porosity, cracks, roughness and new surfaces. Shape factor of particles was determined using three descriptors: circularity, roughness, and aspect ratio. It was also observed that particles produced by HPGR were more elongated, less circular, and rougher than those processed by the ball mill. 1. INTRODUCTION Particle size and shape are important parameters that can significantly affect mineral processing plants and pelletizing plant performances (Brozek and Surowiak, 2007). It has also been proposed that green pellet quality is directly related to the amount of fine particles in a pelletizing plant (Dwarapudi et al., 2008; Umadevi et al., 2008; Gul et al, 2014; Van der Meer, 2015). Particle size distribution and specific surface area (SSA) are also key factors that can control the quality of green and fired pellets. Processing circuits generally reduce the fines fraction to lower than the required specific surface area (SSA). It is therefore necessary to regrind concentrates to produce suitable pellet feed for further treatment in the balling and firing steps [1, 2]. Two main methods are used for re-grinding of concentrate; high pressure grinding rolls (HPGR) and ball mill. Given the different forces used to reduce size in these methods, it is expected the shape of particles will be different (Pourghahramani and Forssberg, 2005)."

Jan 1, 2018

By B. Orberger, J. M. Milazzo, S. B. Blancher, J. Lützenkirchen, J. L. Dubos

"Industrial dusts are commonly agglomerated using empirical recipes with binders such as bentonite, while Sludges are agglomerated into mixes. Those materials contaminate the products, are expensive and generate significant amounts of slag. Achieving cold dust agglomeration with little or no binder requires understanding the controlling parameters in order to predict and optimize the process behavior. This in turn necessitates comprehensive dust characterization to base predictions on measurable characteristics. In the present work we collected 13 Mn-rich dusts over all the process chain: feed fines, smelting, and refining dusts, as well as ferromanganese alloy dust. This is the first systematic study of dusts along the Mn-processing chain for chemical, physical and mineralogical parameters. X-Ray Diffraction, Qemscan® and laser granulometry analyses show that the mineralogy, Particle Size Distribution (PSD) and morphology evolves from complex heterogenous to simple, homogenous along the process chain: The mineralogy of the primary ore dusts shows various hydroxides, oxides, carbonates, tectosilicates and phyllosilicates. The furnace dusts contain oxides, tectosilicates and carbonates with volatiles, while the refining dusts present only oxides and metal. Finally, the Metal dust is nearly pure metal. Particle morphologies and PSD vary from jagged, irregular particles with broad PSD (>1 mm to <0.3 µm) to smooth and spherical with narrow PSD (100 µm to <0.3 µm). The Metal dust is an exception with angular particles. The Cationic Exchange Capacities (CECs) of all samples range from 0 to 22 meq/100g. Specific surface areas (SSAs) range from <0.1 to 27m²/g, and seem to decrease with from ore feed to Metal dust. This may be due to the disappearance of hydrated and/or sheet-bearing minerals, since a smaller grain size usually implies an increased SSA. The zeta potential varies strongly over the range of the samples tested. However, beside the Gabon ore which has an Isoelectric Point (IEP) ~ 4.1, the other IEP ranges between 2 and 2.5."

Jan 1, 2018

By Y. S. Li

The life cycle assessment method is applied to investigate the environmental impacts of cop-per-slag and copper-ore concentration process. Some environmental load data of copper production are obtained. The result indicates that damage level of human health, ecosystem quality and re-sources respectively is 0.174, 0.0203, 0.246 in the copper-slag concentration and 0.112, 0.0136, 0.299 in the copper-ore concentration. Environmental impact of copper-slag production (0.44) is more than that of copper-ore production (0.42), but can meet the environmental protect demand. With domestic copper concentrate supply gap enlarging, recovering copper from slag will lead to a significant improving of resource utilization and development of circulation economics.

Jan 1, 2014

By G. G. Dong

This paper presents BF flotation machines in brief which are manufactured by Beijing General Research Institute of Mining & Metallurgy (BGRIMM). Dimensional analysis and similarity criteria have been used to scale up BF flotation machines. These scale-up criteria can be used to determine mechanical structure and hydrodynamic parameters including mixing, solids suspension, air transfer and power and so on. Similarity criteria are used to design 40m3 flotation machine being based on data from 1.2 m3 to 20 m3 flotation machines. Hydrodynamic tests of 40 m3 flotation machine in water are discussed.

Jan 1, 2014

By R. Singh

The present paper deals with the development of flotation based process for enrichment of a lead-zinc sulphide ore from Ganesh-Himal region of Nepal. Detailed characterisation and flotation studies were carried out under varying process conditions. The sample assayed 2.47% Pb with 13.6% Zn. The ore was predominantly made up of spahlerite and pyrite in association with subordinate amounts of galena, minor amounts of pyrrhotite and chalcopyrite. Dolomite was the main gangue. The modal analysis showed the probability of fair liberation of sulphides from gangues around 210 microns but the locking of galena with sphalerite and other sulphides continued to finer sizes. Under the optimum process conditions the rougher lead and zinc recoveries were 96.3% and 90% respectively. Multistage cleanings of rougher products proved helpful in improving the concentrate grade, meeting the required specification. Based on the studies undertake a process flow-sheet for the concentration of the ore to individual lead and zinc concentrates was developed.

Jan 1, 2014

By A. Ceylan

Pyrite is present as a gangue mineral in most of complex sulphide ores and most of time it is removed as a tailing. However, beneficiation of pyrite from tailings could be important because of its economical value and for the environmental concern. This paper presents a research for the enrichment of pyrite from copper plant tailings, Siirt-Madenköy/Turkey, by flotation. Siirt-Madenköy copper mine is operated by Park Electric Production Mining and Industry since 2005. In order to obtain the pyrite from Siirt-Madenköy copper plant tailings, laboratory test work has to be done to determine the type of reagents, the flowsheet, and the size of plant. The objective of the company is to develop a pyrite flotation circuit for concentration of pyrite from tailing dam to obtain 500.000 tons/year pyrite concentrate. There are about 3 million tons tailings that containing pyrite in the tailings dam. Experiments were carried out with three different types of tailings from the plant and the pyrite concentrate with 46% Fe and 90% recovery has been obtained. Therefore, this study shows that high grade pyrite with high recovery can be recovered from the tailings.

Sep 1, 2012

By Z. Naziemiec

Since several years in Poland a huge demands on mineral aggregates occur, for the reason of intensive development of housing and road industry, as well as industrial building. Limitations in re-sources of broken aggregates in Central and Northern parts of Poland cause, that both the non-waste production of aggregates with high quality and the production of alternative aggregates from recycling gain greater importance, nowadays. It entails increase in demands for crushing devices, which are easy and reliable in operating as well as inexpensive and enabling to obtain a good quality products. Jaw crusher, regarded as the most spread in Polish industry, meet these requirements, however, their crucial disadvantage is a large content of irregular grains in crushing products. Numerous investigations show, that the shape of grains is a significant feature of aggregates, which influences on durability and quality of produced concretes. The advantage of jaw crushers is their easy operation, low price as well as low amount of dusts (wastes) generated in comminution products in comparison to other types of crushers (i.e. hammer crushers).

Jan 1, 2014

By G. Zaitsev

In mining and mineral processing, ammonium and nitrate from residues of explosives and other sources are discharged to the aquatic environment. Nitrogenous compounds in mine water can adversely affect the aquatic environment. The aim of this work was to study the biological removal of nitrate from cold inorganic mine water at the pilot-scale in an operating underground mine. Seven-months pilot testing on biological removal of nitrate from inorganic mine water was successfully performed in denitrifying fixed-bed biofilm reactors. The feed to denitrification bioreactors contained 11 mg NO3--N/L. Methanol was added as an external carbon source to the denitrifying bio-reactor since the inorganic mine water contained only traces of organic compounds (<CODCr (50 mgO2/L). Nitrate removal reached 75 g NO3--N/m3/d with removal efficiencies above 95% at temperature below 4°C. Thus, removal of explosives-residues from cold inorganic mine water was shown in pilot-scale biofilm reactors.

Jan 1, 2014

By Pramila Misra, Jibardhan Meher, Debadutta Das

The concentrated coal-water slurry has been receiving considerable attention recently due its ability to replace fossil fuels. Attainment of stable and concentrated slurry has been succeeded so far through several physical and chemical techniques. The present article reports the formulation and stabilization of a highly concentrated coal-water slurry formed from five varieties of non-coking coals with variable ash contents obtained from Eastern part of India, employing three varieties of starch esters, such as starch benzoate, starch formate, and starch carbamate as dispersant. The apparent viscosity of the modified coal-water slurry has been measured by varying coal loading, dispersant percentage, pH, temperature, etc. The apparent viscosity of the slurry has been found to be decreased substantially on addition of 0.8% of adsorbate in the slurry. The particle-particle interaction has been considerably decreased and stable concentrated coal-water slurry containing high weight fraction of coal (61.5-63.5%) has been achieved in each case. The slurries stay in a non-settling form for about a month with viscosity in a permissible low range. The coal-water slurry has been found to behave as a non-Newtonian liquid. Comparison of the zeta potentials of the naked and modified coals evidences that adsorption of the dispersants at coal-water interface results in inhibition of the agglomeration of coal particles through mostly steric repulsions.

Jan 1, 2014

By M. X. Jia

This paper discusses two mineralogy characteristics that may affect the flotation of sulfide ore. The first one, process mineralogy study on a Cu-Ni sulfide ore shows that valleriite and tochilinite are incline to form on chalcopyrite, pyrrhotite and serpentine surface, and the further guess is that the formation of valleriite and tochilinite may also causes the serpentine transform to talc, so the serpentine surface is a phase of talc or a transition phase from serpentine to talc and this enhances the flotability of the gangue minerals. The second discussion on the flotation behavior of the sulfide minerals from the point of view of the mineral semiconductor character.

Jan 1, 2014

By Ritva Tuunila, Antti Häkkinen

"Wet stirred milling is one of the most effective grinding methods in producing very fine powders in large scale production, but it is a very energy-intensive process, especially when pigments or even nanosize particles are produced. Therefore, optimization of the process parameters is important. The specific energy consumption is a function of stress energy, which describes the effect of tip speed and media characteristics on grinding, and is related to the number of stress events during milling. In effective grinding, a large number of stress events are necessary. The stirrer configuration influences the number of stress events and their intensity, because the motion of the media and the suspension are caused by a rotating stirrer. The effect of three different stirrer types: a pin, disc and blade stirrer, on the grinding rate, i.e. product fineness and specific energy were investigated in this study with a batch laboratory stirred mill with two tip speeds. The material used in the experiments was calcium carbonate. The results obtained with the smaller tip speed showed approximately similar grinding rates and energy consumption for all stirrer types. When looking in closer detail, the blade stirrer seemed to give the finest product with all grinding times compared to the pin and disc stirrers, which both produced almost the same product fineness with the same grinding times. The specific energy consumption was the smallest with the disc stirrer, but not very big differences were obtained. With a higher tip speed, greater differences occurred both in grinding rates and specific energy consumption. The blade stirrer was the most effective in grinding, and the pin stirrer the next. The net energy consumption for the blade and pin stirrers was almost the same, but it was slightly higher for the disc stirrer."

Jan 1, 2014

By E. Yigit

In the flotation process the physical factors such as agitation intensity air flow rate and pulp solid concentration are very important parameters affecting grades and recoveries of the products. The flotation tests were performed on the samples of Bigadic colemanite ore to investigate these factors at different agitation intensities ranging from 1000 rpm to 1400 rpm and air flow rates from 1000 cm3 ? min-1 to 2000 cm3 ? min-1 with 2 L and 4 L cells using Denver laboratory flotation machine. The tested collectors were Cytec Aero 825, Aero 848N and their mixtures. Agitation intensity and air flow rises resulted in more floated material although sometimes being not selective. These effects can be attributed to powerful collisions between air bubbles and mineral particles. The first observation was the effect of pulp solid concentration on the floatability of minerals, while the flotation in 2 L cell (0.125 g.L-1 solid concentration) at 1000 rpm (0.176 wattcm-3), and with 1000 cm3.min-1 air flow rate was possible, the flotation in 4 L cell (0.0625 g.L-1 solid concentration at 1000 rpm. (0.176 wattcm-3) and with 1000 cm3 ? min-1 air flow rate was not possible. However at 4 L cell after increasing agitation intensity to 1200 rpm (0.201 wattcm-3) keeping 1000 cm3 ? min-1 air flow rate, flotation was possible again. This shows that these factors such as agitation intensity have some critical role on flotation. Another interesting observation was on the selective effect of pulp solid concentration. In the flotation with 1 L cell at different agitation intensities, collector Aero 848N was selective against calcite, while in the flotation with 2 L cell at different agitation intensities the same collector Aero 848N was selective against colemanite.

Jan 1, 2014