Search Documents

By Jorj O. Osterberg

The Osterberg (O-Cell) Method makes it possible to separate the side shear resistance (skin friction) from end bearing. The O-Cell is placed on or near the bottom of a drilled shaft and after the concrete is poured and cured, an equal upward and downward pressure is applied. From the test, the load-upward deflection curve in side shear and the load-downward deflection curve in end bearing are drawn. Typical curves are shown where the ultimate load in side-shear is reached and where the ultimate load in end bearing is reached. Several examples of tests in which the test load reached ultimate loads far in excess of what was expected are shown. The side shear in rock sockets is shown to be much larger than generally estimated. Examples are given of where side shear is smaller than expected and the reasons discussed. Disturbance of the sides of drilled holes due to poor construction techniques and ways to avoid these conditions are considered. Examples of bottom hole disturbance are given and ways to prevent the disturbance are discussed. A graph showing the actual measured capacity of drilled shafts compared to the estimated capacity as a function of the hardness and strength of the soil or rock is presented.

Jan 1, 1999

By Walter Ensinger

Special foundation works is one of the most innovative sectors in civil engineering and construction. Both engineering techniques and construction machinery are undergoing continu­ous further development. These developments are providing ways to meeting the world-wide requirement for special geotechnical works even faster, even better and more efficiently. Unfortunately, accident prevention organisations have had to realise that the figures on in­dustrial accidents in special foundation works are still above average in number. The Safety & Environmental Working Group of the EFFC thereupon started to carry out a survey on acci­dents occurring in this sector and used this information as a basis for the preparation of acci­dent statistics and an accident analysis. The objective of this undertaking is to determine key accident occurrences and their causes and to consequently determine measures for improved health and industrial safety.

Jan 1, 2002

By Donald J. Murphy

Longevity of structural units, as compared to the planned useful life of a facility, always is a design consideration. Typical concerns include slow decay due to environmental factors, and changes in constitutive relationships governing the performance of the material involved. With respect to foundations, the usual items of interest are corrosion of steel and concrete, and time dependent behavior of the soil/structure system. For piles, as with other foundations, deterioration is precluded, mitigated or otherwise accounted for by assessing properly the ambient situation (sulphates, pH, stray currents, resistivity) and providing safeguards, such as resistant construction products, oversizing, coatings, and/or cathodic protection. On the other hand, long term performance of the pile foundations, as affected by time dependent characteristics of the supporting soil or rock, can be predicted and controlled only with a synergetic coupling of analyses and field tests. The history of a project for which this approach was followed forms the basis for this paper.

Jan 1, 1986

GENERAL CONTRACTOR: ALEXANDER CONSTRUCTORS, INC. STRUCTURAL ENGINEER: CAGLEY & ASSOCIATES, INC. GEOTECHNICAL ENGINEER: F.T. KITLINSKI & ASSOCIATES, INC. PILE FOUNDATION CONTRACTOR: L.G. BARCUS AND SONS, INC. PROJECT PROFILE: 108-10 in. diameter AugerPiles installed to an approximate depth of 32 ft. Piles were installed through Stiff Clayey Fill and Medium-Dense Sands to Decomposed Shale. Piles were drilled to a refusal criteria of 1 ft. / 3 min. Piles were installed using a Barcus Mantis AugerPile rig which is large enough to install piles 25 to 50 ft. long outdoors. The Mantis is also ideal for indoor and low overhead installations. On top of being extremely versatile, the Mantis is also very economical to mobilize. The existing structure is supported on H-Piles. The AugerPiles were furnished and installed for less than the material price of the H-Piles. Design loads were under 40 tons which eliminated the need for a load test. AugerPiles were selected for minimal vibration, limited noise, and economy.

Jan 1, 2001

By Mohammed Sakr

The use of helical piles as a deep foundation option has considerably increased in the recent years to support a variety of loads, from small loads for several applications such as residential housing, solar farms, utilities and retrofit projects, to large loads for many applications such as commercial, power transmission lines, oil facilities and industrial applications. Therefore, it is necessary to qualify and quantify their axial capacities and performance characteristics. This paper presents the first full-scale axial compression and tension (uplift) testing program executed on large capacity helical piles installed in cohesionless soils. A total of eleven pile load tests using either single or double-helix piles with shaft diameters that varied between 324 mm to 508 mm (12¾ in to 20 in) were carried out, including seven axial compression tests and four tension (uplift) tests. The results of the axial compressive and tensile pile load tests as well as field monitoring data of helical piles installed in dense sand are presented in this paper. Based on the results of this study it was found that helical piles have developed significant resistance to axial compressive loads up to about 2920 kN (656 kips) and tensile loads up to 2900 kN (652 kips).

Jan 1, 2011

By Sun Shao Xian

The Port of Shekou is situated at Shenzhen Bay on the east side of the Pearl River estuary. Geological condition of the site is quite complicated. On top of the sea bed, there is a layer of soft silt 8 - 14 m thick. Under the soft silt, there are intercalated layers of sand, silt and clay. Average surface elevation of the underlying undulatory weathered bed rock is about - 20 m, with a variation of about 10 m. In certain locations, the weathered bed rock is covered with a layer of silt 3 - 4 m thick. This paper gives brief account of three types of wharf structures which are of particular interest, constructed in the last few years: (A) Platform type wharf structure with frontal sheet piling and steel raking pile in the rear; (B) Relieving Platform type structure with steel sheet piling and inclined anchoring HP pile ; (C) Steel pipe pile row supported apron added to a marginal quay. Average construction time of a deepwater berth is about six months.

Jan 1, 1991

By Carl-John Grävare

This paper deals with some of the systems and equipment that are being developed and/or are in use in Scandinavia. The main subject is the development of loading tests on the piles using monitoring equipment. This paper also describes ground improvement using lime-cement columns, expander body piles and steel core piles.

Jan 1, 2000

By Guo H. Lei

Over the last four decades, barrettes have been ever-increasingly adopted as the foundations for tall buildings and heavy infrastructure projects all over the world. Many findings have been gained from practical applications and theoretical researches. In this article, a collection of literature is reviewed on the installation effects and load-carrying behaviour of barrettes derived from field and laboratory tests and theoretical studies. It covers many aspects, such as the ground deformations and stress changes caused by the installation of barrettes, the shaft resistance mobilisation behaviour, the construction effects on the shaft resistance, and the effects of pile spacing, pile shape and pile group layout on the load-carrying behaviour of barrettes.

Jan 1, 2006

By K. Viking

The vibratory characteristics of full-scale sheet piles, vibratory driven into the ground, have so far not been described systematically in detail. This paper concerns the preliminary results of a series of full-scale field tests where both the driveability and induced ground vibrations have been continuously monitored. Furthermore, the results of measured ground vibration levels have been measured at two different sites characterised as having hard and easy driving conditions. In the light of the presented results, the paper briefly discusses how the complexity of a driveability and vibration prediction can be subdivided into three parts, namely, vibrator-, sheet pile-, and soil-related parameters, all of which significantly affect both the driveability and induced ground vibrations.

Jan 1, 2000

By Upendra L. Karna

The pile capacity gain with time evaluated and implemented for the construction of the Route 21 Viaduct in Newark, NJ, U.S.A is discussed in this paper. The project consisted of the replacement of more than 3.2 km of viaduct and ramps. The project site consists of thick residual materials deposited by the Wisconsin Glacier over sedimentary rocks. The upper portion is glacial-lacustrine deposit underlain by marginal morainic till and stratified drift. Subsurface investigations identified significant variations in layer thickness and grain size consistency. The site was characterized into 4 Soil types, based on subsurface soil behavior. Closed end 600 mm and 450 mm diameter driven pipe piles were used for the foundation. Loading tests conducted during an advanced construction contract, established that a significant soil set-up could be expected. For the first construction contract, a pilot loading test program consisting of 112 dynamic loading tests and 77 re-strikes (at 2 to 4 weeks) using the PDA (Pile Driving Analyzer) with CAPWAP (Case Pile Wave Analyses Program) was conducted to establish the soil set-up behavior. Nine (9) quick static loading tests were conducted to substantiate the long-term pile capacity. Based on the loading test results, average set-up factors were established and utilized for developing production pile driving criteria. Bearing resistance with depth was analyzed and reviewed. The set-up factors varied significantly, ranging from 1.05 to 1.89, and averaged about 1.30. Conclusions are derived. Set-up factors behavior for each soil type plotted by linear regression are presented and discussed. An appropriate set-up with time relationship for a glacial soil is suggested.

Jan 1, 2006

By N. V. Nayak

Maharashtra State Road Development Corporation Ltd., has initiated a scheme for construction of 55 flyovers in Mumbai in India. To ensure speedier completion of projects several new technologies were adopted to save time without compromising on safety and reliability. Many of the flyovers involved large diameter pile foundations carrying loads ranging from 3500kN to 1375kN. Significant time would have been lost in using conventional load testing procedure to check pile capacity apart from the difficulty in mobilizing the load and the obstruction to site movement and traffic on the adjoining roads. High Strain Dynamic Testing was introduced on the project sites in lieu of static load testing after conducting numerous co-relation studies on various project sites. A total of seven co-relation studies have been conducted till date and based on these data static testing has been replaced by dynamic testing on numerous flyovers. The paper presents the results of such studies. CAPWAP analysis was also conducted on the data to evaluate the percent skin friction and end bearing so as to improve future design parameters.

Jan 1, 2000

By John J. Vieaux

Allowable loads on Dynamically-Cast-In-Place Piles (the Franki type) can be correlated with N values from the Standard Penetration Test. Using a constant developed by Nordlund, a conservative value for load-carrying capability of a DCIP pile is developed. The DCIP pile and method of installation is briefly described.

Jan 1, 1984

By Hayel M. El-Naggar, Sherif A. Akl

Although grouted piles have been used for several decades since the idea was proposed in the 1970s, their design is mostly based on experience and unpublished proprietary methods. There is little research on grouting drilled shaft tips and even less on grouting shaft sides. This paper presents the analysis of 4 instrumented pile loads tests on base and shaft grouted piles from different sites in Egypt; with emphasis on one of the tests, to demonstrate the analysis process. The data from the tests are analyzed to model the development of unit side friction (USF) with relative displacement. A numerical model using the finite element software PLAXIS is used to investigate the effect of grouting on the surrounding soil stress state. The paper combines the observations from full scale pile load tests and results from the numerical model to suggest an idealized behavior of side friction development with relative displacement of the grouted part of the shaft. The suggested model considers an envelope of Unit Side Friction (USF) with relative displacement, initially dominated by the grout resistance then at higher relative displacements, the friction with radially pressured soil takes over. The grout provides very high USF values up to a relative displacement of 2mm. Then, the USF drops to a typical pile soil side friction behavior; however, this friction is affected by the contact stress between pile and soil, which significantly increases due to compaction grouting. INTRODUCTION Base and shaft pile grouting has been significantly developing in recent years to accommodate the unfavorable conditions in major projects such as the high loads in high rise building and founding on problematic soil formations. Grouting aims to decrease settlements and increase the capacity of the pile under axial load. The technique is first introduced by Kraft (1974) but gained popularity in the 1980s. Typically there are two types of grouting; compaction, and permeation. Compaction grouting is more common in pile foundations practice, and many researchers have provided case histories of pile load tests on base grouted piles and base and shaft grouted piles (Gouvenot and Gabaix,1975; Stocker, 1983; Ghazali et al., 1988; Fleming, 1993; Kusakabe et al., 1994; Robson and Wahby,1994; Joer and Randolph, 1998; Hamza and Leoni, 1998; Mullins et al. 2000; Littlechild et al., 2000; Suckling and Eager, 2001; Dapp and Mullins, 2002; Ho, 2003; Fu and Zhou, 2003; Brettmann and NeSmith, 2005; Ruiz, 2005; Mullins, 2006; Dapp and Brown, 2010; Beadman et al., 2012; Nguyen et al., 2013; Miller et al., 2013; Sinnreich and Simpson, 2015; Hui and Lin, 2015). Compaction grouting is meant to densify the soil around the pile and below the base rather than permeate this soil and increase its cohesion. Research showed that grouting increases the capacity of the piles by a factor of 2~5. The variation in capacity increase depends on pile type, grouting process, and especially grouting pressure. Although there are many case histories of pile load tests on grouted piles but there is no well-defined agreed-upon method to predict grouted pile capacity as typically done in ungrouted piles. Few lab experiments discussed the shaft grouting effects on the soil especially the compaction grouting. The experiments concluded that the compaction grouting forms a homogeneous layer between the pile and the soil, and a residual effective stress is achieved simultaneously with a significant densification of the soil around the pile with noticeable decreasing in void ratio. (Fattahpour et al., 2015; Wang et al., 2015). Recently, studies used numerical analysis to investigate the behavior of the grouted piles and the changes in the surrounding soil (Chiang et al., 2013). That study presents a simulation of the base pressure grouting with a simple FE model and predicts the reduction of the pile settlement by 10 to 20%. Another numerical study using a complex model conducted by Zhou et al. (2017), pr

Jan 1, 2018

By G. Sauer

"More Skill is needed to avoid rather than to handle heavy ground loads." This finding, from a tunneling engineer of the nineteenth century, is still relevant today with all advanced sequential excavation and support methods available whether they are applied in the vertical or horizontal direction. Balanced contractual agreements and documents are important since they provide the spirit and climate at the site. This article aims to describe the means and measures for 'hand mined' shaft and tunnel support as they are available today. Some special construction elements and methods with a perspective in recent developments in order to avoid getting stuck in conservatism are presented as well. If we don't allow new methods, means and measures we may end up with the famous quote "Only women who have already proven they are able to give birth to a healthy baby are allowed to become pregnant!"

Jan 1, 2003

By Jacques Moraille

The public is asking for more aesthetic designs if they can be proven cost-effective at providing an appealing element to new dams. Lake Lenexa was designed and built around the idea of providing for basic dam functions such as flood control, enhanced water quality, recreation but also to provide an inviting community focal point for the residents to visit and enjoy; truly interact with the dam. The architecturally unique dam and ?one of a kind? spillway were designed to symbolize the water cycle as water moves from nature into the urban environment and the back to nature. A pedestrian bridge that spans the spillway offers visitors a good view of cascading pools and a fountain. The original Lake Lenexa dam layout incorporated relatively high, cast-in-place concrete retaining walls to form the spillway structure. The Black & Veatch project team performed a Value Engineering (VE) study to determine cost-effective means for implementing architectural features within the spillway, which resulted in innovative uses of construction materials not typically used in dam and reservoir construction. The VE study concluded that mechanically stabilized earth (MSE) retaining walls that are normally used for transportation projects would be a cost-effective alternative to the originally planned cast-in-place wall systems for the main spillway and stilling basins. The Black & Veatch study added value by mixing cement-kiln dust (CKD) with on-site clay soils to produce a stabilized material for use under the spillway. The CKD stabilized material properties include low compressibility, high strength and low permeability, which reduced seepage and uplift pressures under the spillway slabs. The cost savings provided by the VE alternatives reduced total costs and enabled architectural elements. The award winning dam design also used drilled caissons, expanded polystyrene (EPS) block forms, customized steel forms and external concrete vibrators to build the pedestrian bridge and upper spillway structures.

Jan 1, 2009

By Robert W. Bergwall

The $58,000,000.00 Columbia Heights Metro Station project (Section E3-a) forms a part of the Washington Metropolitan Area Transit Authority's (WMATA) Greenbelt Route - Green Line subway system. The Greenbelt route is one often segments that make up WMATA's subway system. Construction of the "cut and cover" reinforced concrete station includes 600 linear feet of an underground center platform, two ancillary service areas totaling 466 linear feet, two surface entrances, and vent shafts (See Figure No. 1). Station subgrade is approximately 60 feet below existing grade. The project can be divided into five main areas: 1. North Service Rooms and Passageway; 2. West Entrance and West Passageway; 3. East Entrance; 4. Center Platform; 5. South Service Rooms. Station dimensions are approximately 1068 feet long by 64 feet wide. Construction commenced at the site in January of 1995 and is expected to be completed by December of 1999. Franki Northwest Company, Crofton, Maryland, was awarded a subcontract by general contractor Blake Construction Company, Washington, D.C, to install the support of excavation and temporary decking systems. Franki's scope of work included the installation of 490 drilled soldier piles plus two elevator shafts totaling 29,700 linear feet of drilling; 1,150 tons of steel decking covered by 37,000. square feet of precast concrete deck planks; 120,000. square feet of timber lagging; 2,500. tons of struts and wales; and temporary support of underground utilities. In conjunction with Franki's work, Bencor Corporation of America, Dallas, Texas, constructed parallel, 600 foot long slurry walls which serve as permanent walls for the center platform portion of the station.

Jan 1, 1997

By Gyimah Kasali

Rapid Load Testing was performed as part of an extensive drilled pier testing program for the University of California Berkeley Capital Improvement Program. The purpose of the program was to: (1) Verify the axial compressive design capacity values for the planned 24" piers, and to estimate the capacity of the existing 30" CIDH piers, and (2) To evaluate the seismic performance of the proposed drilled shafts. The Fundex PLT was used since the loading period of the PLT is very similar to the period of a seismic event, making it an ideal tool to model the pier response to seismic events. "Performance-based design" of structures subject to seismic loads has been of particular interest to UC Berkeley Seismic Review Committee and the Pacific Earthquake Engineering Research Center. The comparison of static tests to Rapid Load testing also provided valuable correlations. The program represents one of the most comprehensive drilled pier test programs on the West Coast. The testing program consisted of Rapid Load Testing using the Fundex PLT on 6 drilled piers. Rapid Load Tests were followed by conventional static compression and tension tests on selected piers, followed by another cycle of rapid load tests on the statically tested piers. The piers featured extensive instrumentation to allow detailed interpretation of the test result. Correlations were drawn to compare static load test result to that of the PLT in the particular soil profile, and the PLT also provided the data to analyze the ultimate seismic capacity of the piers. The load test results indicate that the ratio of interpreted failure load from the PLT data to the corresponding load from the static load test data is about 1.2 to 1.3 for the clayey soils underlying the test site. The results also indicate that the PLT offers an economical approach to defining the stiffness of drilled pier foundations subjected to seismic loads for use in performance-based design.

Jan 1, 2002

By Mohammed Sakr

This paper presents the results of a full-scale axial compression and tension (uplift) testing program executed on large-capacity helical piles installed in very stiff to very hard clay till soils (i.e. cohesive soils). A total of ten tests including six axial compression tests and four tension (uplift) tests were carried out. The results of the axial compressive and tensile pile load tests and field monitoring of helical piles with either a single helix or double helix are presented in this paper. Helical piles are traditionally used to support light to medium loads (i.e. loads up to 500 kN or 56 tons). However the results of the present study confirmed that helical piles can support significantly higher axial compressive loads up to 2450 kN or 275 tons, which is about 5 times traditional design loads. The study also demonstrated the high tensile capacities of helical piles which was as high as 85% of their compressive capacity. Hence helical piles can provide a viable design option for foundations supporting relatively heavy loads.

Jan 1, 2012

By C. Vipulanandan

It is critical to monitor the ground conditions during excavation and drilling of boreholes during construction to identify possible changes in the soil and rock formations. Drilled shafts are increasingly used as foundations to support structures, bridges and other facilities in geomaterials such as soft-rocks and hard clays. Locating the bottom of the borehole during construction with the required design strength is critical. Hence developing a simple device that could be easily adapted/used with the drilling tool was of interest in this study. Determining the shear strength of the geomaterial in the borehole and at various elevations including the bottom of the borehole can lead to better quality control of construction by identifying the various layers based on strength. In this study, a down-hole penetrometer (DHP-CIGMAT) was designed, built, calibrated and tested in the field to determine its effectiveness in measuring the strength of soil/soft rock in the boreholes. Based on limited field tests, linear correlations between geomaterial strengths and DHP-CIGMAT deflection have been developed. The DHP-CIGMAT can be used to identify soils and soft rocks.

By George Piscsalko

There are numerous methods currently available to assess the integrity of drilled shaft and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity of drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube, or from embedding thermal wires within the shaft. This Thermal Integrity Profile method will be described in detail and one case history will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

Jan 1, 2011