Search Documents

By M. Y. Williams

Introduction During the economic investigation of Pacific Great Eastern Railway subsidy lands, the P.G.E. Survey of Resources made a geological and mineral survey of a large part of the valley of the Peace river as included in the Province of British Columbia. The immediate valley of the Peace river was surveyed from the mountains to the Alberta boundary; the valley of the Pine river was surveyed throughout; and the Dominion block, 70 miles square and lying astride the Peace river, westward from the Alberta boundary, was very carefully surveyed. The writer was in general charge of the field work, and spent half the field season of 1929 and the field season of 1930 in the region . J. B. Bocock, however, did the major part of the work, spending two seasons, 1929 and 1930, in the area. General Conclusions The rock formations within the area discussed are all sedimentary and range in age from pre-Cambrian to recent. As might be expected, the minerals are in the main non-metallic, coal being by far the most important. Favourable conditions exist for natural gas occurrence, and suitable structures for petroleum concentration occur, although the high carbon ratio of the coals sheds considerable doubt upon the actual occurrence of oil in the area. Materials of minor interest are ochre, calcareous tufa, marl, limonite, gravel, and building stone.

Jan 1, 1934

By B. E. Shaw

This paper describes the use of the Free Piston Valve, and a simple hoist brake control system, which has been developed over the last two years, greatly improving the performance of low-pressure brake engines. The basic control system is outlined, with sections devoted to emergency trips and differential braking, and the application of the system to deep shaft hoisting is discussed.

Jan 1, 1966

By R. F. Dawson, A. S. Bagnall, K. Barron

"At Smoky River Coal Limited (SRCL), economic occurrences of structurally thickened coal deposits form attractive surface mining targets. These steeply dipping, structurally complex deposits require that special attention be given to pit wall design and operational practices.Where anchor support is feasible, there is potential for reducing footwall waste requirements and/or increasing coal recovery. SRCL has used rock anchors to support footwall slopes since 1985. This paper outlines design considerations and performance of rock anchor support systems at SRCL.Three case histories are included that illustrate the design process for supporting steeply dipping footwall slopes using rock anchors.IntroductionWestern Canada contains vast reserves of high grade coking coal largely located in two belts within the Rocky Mountain Foothills straddling the Alberta/British Columbia border. There are about one billion tonnes of ""clean"" coking coal reserves (Romaniuk and Naidu, 1986) situated near existing mining infrastructure. Within the reserve areas shown in Figure I, a total of six producers operate 10 large mines linked with ports situated on Canada's west coast. Al! of the producers operate conventional shovel/truck surface pits.Surface mineable reserves within some of the mountain coal mines are located on dip slopes or where the geologic structure has thickened the coal near the surface, creating low strip ratio targets. Footwall slopes in these mines are developed parallel to bedding, thus minimizing waste extraction and preventing undercutting of potentially unstable strata. The base of the mineable coal measures in both north and south regions is marked by massive quartz sandstone units (Torrens Member and Moose Mountain Member) which often form the footwall. Footwalls developed within this basal sandstone unit can attain very high unbenched heights often with little risk of instability. In cases where the footwall is developed on weaker strata above this basal unit, stability considerations control slope height when bedding dips exceed about 30°. In these situations it is desirable to assess the benefits of artificial support to increase the unbenched footwall slope height."

Jan 1, 1995

By W. V. McKnight

The paper discusses the equipment and methods used to establish some of the characteristics of a braking system. Some typical tests are described and an explanation of the approach used to derive information from the recorder charts is given.

Jan 1, 1966

By Craig Faulkner

Discharge cones for large Semi Autogenous Grinding (SAG) and Autogenous Grinding (AG) mills are subjected to high wear as significant volumes of ground ore and slurry exit the mill. With the larger diameter mills of 32ft to 40ft in size becoming the norm, very high, concentrated wear is highlighting the limitations of conventional discharge cones and frequent changes are subsequently required. This paper outlines the advances made in the design of the Bullnose discharge cone. Superior wear materials to increase wear life over conventional rubber or chrome-moly steel discharge cones and the introduction of key design features to reduce reline times and improve fit and safety during installation, offer significant opportunities for the mill operator. Collated from multiple case studies, the wear data and reline history from 2004 to present clearly illustrate the way in which superior component longevity has reduced the frequency of relines over the life of the product to increase mill availability and effectively increase the tonnes milled in a period.

Jan 1, 2012

By A. J. Hyett, N. Hedrick, J. Blackall

The Garford bulb anchor is a modified cable geometry developed and patented by Garford Ply Ltd. of Australia, and which has recently become widely available in Canada. It is produced by deforming the seven wires (including the central kingwire) of a standard cable into a bulb" (Fig. 1). Laboratory cable pull tests indicate that the bond capacity of the 25 mm Garford bulb anchor is comparable to the nutcase cable, in excess of the birdcage cable, and significantly higher than standard 7-wire strand. Its comparative advantage over the latter is most significant for tests at low radial confinement and high water:cement ratio grout, which corresponds to operational conditions of low quality rock (i.e. weak, highly fractured rock masses, foliated hanging walls, failed ground, etc.) and poor installation quality control (perhaps the most common explanation for cable bolt failures). It is under such conditions that cable bolting is often ineffective. The most impressive result is that for a reduction of the effective rock mass modulus by a factor of five, the Garford bulb cable capacity remains virtually unchanged.

Jan 1, 1995

By J. Robitaille, P. Cousin

"Agnico-Eagle Mines Ltd, Laronde Division, is a gold operation processing ore containing copper and zinc. Copper is recovered as a concentrate prior to gold cyanidation.Copper concentrate grade was improved with the implementation of an on-stream analyzer. Further improvements to the copper concentrate grade could be achieved throughefficient zinc depression.High cyanide cost linked to the copper content in the flotation circuit tails, prompted some modifications to the flotation circuit. Economics and environmental issues were considered. A Maxwell cell was retrofitted with an Outokumpu HG cell mechanism stabilizing it's operation. Secondly a flotation column was added to increase circuit capacity.This paper will address flotation circuit operation difficulties, successes and results achieved before and after modifications.RESUMELes Mines Agnico-Eagle division Laronde sont considéré comme étant un producteur d'or. Le minerai révèle toutefois des teneurs appréciables en cuivre et zinc. Un circuit de traitement combinant des étapes de flottation du cuivre et de cyanuration de l'or a été adopte. Le rejet de la flottation est lixivie pour son contenu en or.La teneur moyenne en cuivre du concentre final fut augmentée suite a l'implantation d'un système d'analyse en continu. Une séparation plus efficace de la sphalérite se devra d'être obtenue afin d'améliorer davantage la qualité du concentre produit.Le contenu en cuivre au rejet du circuit de flottation influence directement la consommation en cyanure. Pour cette raison, certaines modifications à la flottation sont devenues nécessaires. Des facteurs d'ordre économique et environnemental ont été considérées. Une cellule existante fut transformée en cellule HG d'Outokumpu, stabilisant son opération, et une colonne de flottation fut ajoutée au circuit afin d'accroitre sa capacité.Le présent document se veut une rétrospective des problèmes d'opération vécus, des solutions apportées ainsi que des résultats obtenus et de leurs implications suite aux améliorationseffectuees."

Jan 1, 1995

By R. F. Dawson, A. S. Bagnall, K. Barron

"At Smoky River Coal Limited (SRCL), economic occurrences of structurally thickened coal deposits form attractive surface mining targets. These steeply dipping, structurally complex deposits require that special attention be given to pit wall design and operational practices.Where anchor support is feasible, there is potential for reducing footwall waste requirements and/or increasing coal recovery. SRCL has used rock anchors to support footwall slopes since 1985. This paper outlines design considerations and performance of rock anchor support systems at SRCL.Three case histories are included that illustrate the design process for supporting steeply dipping footwall slopes using rock anchors.IntroductionWestern Canada contains vast reserves of high grade coking coal largely located in two belts within the Rocky Mountain Foothills straddling the Alberta/British Columbia border. There are about one billion tonnes of ""clean"" coking coal reserves (Romaniuk and Naidu, 1986) situated near existing mining infrastructure. Within the reserve areas shown in Figure I, a total of six producers operate 10 large mines linked with ports situated on Canada's west coast. Al! of the producers operate conventional shovel truck surface pits.Surface mineable reserves within some of the mountain coal mines are located on dip slopes or where the geologic structure has thickened the coal near the surface, creating low strip ratio targets. Footwall slopes in these mines are developed parallel to bedding, thus minimizing waste extraction and preventing undercutting of potentially unstable strata. The base of the mineable coal measures in both north and south regions is marked by massive quartz sandstone units (Torrens Member and Moose Mountain Member) which often form the footwall. Footwalls developed within this basal sandstone unit can attain very high unbenched heights often with little risk of instability. In cases where the footwall is developed on weaker strata above this basal unit, stability considerations control slope height when bedding dips exceed about 30°. In these situations it is desirable to assess the benefits of artificial support to increase the unbenched footwall slope height."

Jan 1, 1995

By E. H. Holm

"This paper is a market-oriented review of the industry's present and forecasted performance, considering some of the principal factors influencing natural resource development. The author illustrates the steady consumption growth of nickel, and stresses the need for a quantitative long-range approach to production, consumption and the supply/ demand balance on a worldwide basis. Objective consideration of this data exposes some popular misconceptions. The possibility of near-term undersupply of nickel is discussed in relation to historically rapid changes in inventories and demand patterns. What is the significance of the increasing reliance on lateritic sources? New• facilities, new processing methods and new product forms are illustrated as further evidence of the industry's determination to satisfy the needs and preferences of nickel consumers. Examples indicate how product forms must accommodate to fast-evolving end-use technology. A review of nickel's price performance is used as a base from which to explore tomorrow's price trends."

Jan 1, 1972

By J. A. Hillier

"IntroductionThe purpose of sampling is to remove a portion of material from a stream which is representative of it in size, moisture and mineral content.To prevent the effects of segregation, generally caused by the way in which a conveyor, pipe or launder is loaded or directed, the sampler should cut proportionally the entire cross section of the stream.If one conveyor transfers to another at a right angle, fines may be dropped on the near side, and the coarse material thrown to the opposite side. Segregation can also occur as a result of the motion of a conveyor belt passing over the idlers causing the coarse material to roll to the sides of the belt.When slurry changes direction of flow in a launder or pipe, the heavier and coarser fraction will centrifuge to the outside of the curve and tend to remain on one side of the stream. Similarly, if two streams joining in a common launder are not mixed at the point of confluence, they will continue down the launder unmixed . This effect is particularly noticeable in a plastic lined launder.Therefore, a proportional sample is usually accomplished by a constant rate of cutter travel across the entire stream, making certain that the cutter is not full or splashing over before reaching the end of travel.The cutter should operate on a constant interval based on time, tonnage and uniformity of flow. The opening should be at least three times the width of the largest piece to be sampled. The cutter width is more critical with ore samples where particle sizes are large. With slurry samples, the opening is usually much larger than the minimum in order to obtain sufficient samples"

Jan 1, 1989

By Joseph B. de Hart

Two papers recently published on the subject of mine ventilation: "The Theory of Ventilation," by Douglas Hay. and "The True Effect of Natural Ventilation in Deep Mines," by Robert Clive, form the first and second reports respectively of the committee on the Ventilation of Mines appointed by the Midland Institute of Mining Engineers. The purpose of the present paper is to draw attention to these two papers and the discussion thereon. The theory of ventilation as taught in our schools is based on Atkinson's formula, which is a variation of Chezy's formula for the flow of water in pipes. The formula depends on two assumptions : 1. That air is an incompressible fluid within the limits ordinarily encountered, and; 2. That the pressure required to produce ventilation varies as the square of the rate of flow. The Atkinson formula has been assumed to hold good over the entire range of conditions met with in mines.

Jan 1, 1924

By Z. D’Amico

"IntroductionWE HAVE HEARD quite a lot recently on newer methods -of supporting roof, such as roof bolting or the use of metal props and •booms, but, with the exception of roof bolting, these methods are confined mostly to comparatively low, regular seams and even .bolting cannot be used to hold soft sides. Thus, where a seam of coal has great variations in thickness, or where it is faulty, or where the coal sides must be supported, nothing can wholly take the place of timbering with wood. This paper will deal mainly with the method of timbering such a seam, namely, the No. 3 seam mined by Brazeau Collieries, Limited, at Nordegg, Alberta, where the full height of a thick seam is mined in development. However, a few words on one or two other systems practised in Alberta when, in development work, a thick seam is only partially mined, should be of interest.Examples of Timbering in High SeamsThere .are several methods in use today for dealing with high seams of coal. The most popular is to develop the seam by driving road-ways in the coal by some conventional method, usually recovering the full thickness of the seam on the retreat. The following examples illustrate two variations of this method.In Figure I we have a thick •seam of friable coal, with a good roof, pitching about 30 degrees, which is being mined by taking the upper part of the seam in the development work, leaving the •bench coal in place. Figure 1A shows a section through a room."

Jan 1, 1954

By Mustafa Kumral

Monte ? Carlo simulation is often used to assess the risks associated with uncertain variables in mining operations. The success of Monte-Carlo simulations depends upon reproducing the dependencies among variables to some extent. However, some variables may exhibit different dependency patterns. In these cases, classical techniques for dependency quantification cannot capture dependencies. As an alternative, the copulas allow modeling nonlinear dependencies. Furthermore, any choice of marginal distributions can be used. Especially, for the data, which is sensitive to extreme case such as financial crisis, the copulas arise as a means to reproduce the correlations among variables. In this paper, the copulas are introduced to mining practitioners using Monte-Carlo simulations for risk assessment. Then, a case study is given to show the superiority of the copulas over classical techniques using ModelRisk Software. In conclusion, it was observed that the copulas enhance the quality of Monte-Carlo simulations by capturing variable dependencies.

Aug 1, 2013

By S. Zakaria

"Inco's Automated Haulage Truck System (AHT) is a revolutionary automatic guided vehicle that performs all load, haul and dump operations without human intervention. The high level of sophistication and the short period it has been in operation has only allowed a select few Inco personnel to become familiar with the ART operation and maintenance. As an aid to operations an expert system using the knowledge gained from the experienced specialists was implemented in the field.The AHT operating and maintenance assistance expert system will reason through the information given, arrive at conclusions and give advice to operations, technical and management personnel. It will provide comprehensive real-time troubleshooting assistance for the hydraulic, electrical and mechanical subsystems of the ART. The ART expert system has many benefits to Inco which include increased skill levels of ART operations and maintenance personnel, reduction in ART downtime, standardization of troubleshooting procedures and reduction in ART operating and maintenance costs. In the future, the expert system application will be linked to SCADA (Supervisory Control and Data Acquisition), maintenance and statistical software to display current and historical trends of variables from a centralized historical database. As well, a wide variety of features will be integrated into the system including AutoCad drawings, graphics, photographs, voice and video capabilities."

Jan 1, 1994

By Zainelabdin Khalid Zainelabdin Elfaki

The influence of partially replacing cement with marble waste on the workability and compressive strength of concrete bricks was investigated. Three replacement percentages, 10%, 20% and 30% weight marble waste, were used with different curing times of 7, 14 and 28 days. Two specimens were prepared for each percentage and curing time. For this study, marble powder from the Mining House Company in Saudi Arabia was used. It was observed that the replacement of cement in Concrete brick with marble waste enhanced the loading strength and the workability of the prepared concrete bricks. It was also observed that 20% replacement of cement with marble waste was the best replacement percentage compared to the other replacement percentages tested. Marble waste from manufacturing companies, either in powder, sludge or slab form, has negative impacts on the environment. In contrast, reusing marble waste has both economic benefits (i.e., selling the marble waste) and lessening the need for raw resources.

Jan 1, 2014

By H. C. Rickaby

Introduction The township of Swayze, from which the Swayze gold area derives its name, is in the Sudbury mining division, approximately 150 miles northwest of Sudbury. The gold area may be regarded as situated at the southwest corner of a triangular area whose northeast and southeast corners are at Porcupine and Shiningtree, respectively, and whose sides are between 70 miles and 90 miles in length. On a geological map, it would be found that belts of Keewatin greenstones and sediments form the sides of this triangle, and that they surround a large granite mass. Prior to the summer of 1931 the Swayze corner of this triangle had probably been less prospected than the other parts and comparatively little was known of it from the standpoint of gold mining possibilities. The extensive belts of iron formation to the south and west of Swayze received some attention about the year 1909, and during the years 1927 and 1928 some prospecting was done in the townships of Greenlaw and Cunningham, south of Swayze, but chiefly for base-metals- copper, zinc, and lead. In the summer of 1931 a very promising discovery of gold-bearing quartz was made by J. G. and J. L. Kenty, working for the Brett-Trethewey Mines, Ltd., in association with Northern Canada Mining Corporation, and Northland Prospectors, Ltd., and this property, now known as the Kenty Gold Mines, Ltd., has been actively developed with very encouraging results. Following this discovery a6d during the summer of 1932 much prospecting took place in the area, as a result of which a number of other discoveries of gold were made, chiefly to the west of the original find. They are distributed over a wide area, which includes the townships of Rollo, Raney, Swayze, Denyes, Halcrow, and Greenlaw.

Jan 1, 1933

By Karl Houseley, Dr. Robert J. Chapman

"A gravity concentration process has been applied to ores from the Clogau Mine, north Wales, the Tyndrum deposit, central Scotland and an alluvial ore from Leadhills area of Scotland. In the case of the Welsh ore and the alluvial deposit the gold grains in the concentrate and tailings streams have been characterised in terms of their three dimensions.In the case of Welsh ore, the thickness of a gold grain has been shown to be the single most important factor in determining behaviour in a gravity concentration operation. Six indices were used to quantify the overall geometry of the gold grains and those which incorporate a thickness term have proven to be effective in predicting the destination of gold particles within the concentration circuit. It is proposed that the most simple of these, the Heywoods flakiness ratio, has potential for the control of milling operations as an alternative to the established practice of characterising the size of the mill discharge.The effect of grain geometry on the recovery of fine gold has been studied using Tyndrum ore. The recovery of gold by gravity concentration increased from 20% to 70% when the criteria used to design the milling operation was the prevention of over grinding of gold grains.The destination of alluvial grains in the concentration circuit did not show such dependence on shape, and this has been attributed to the effective classification of all the gold grains in the sample by fluvial action producing a population of similar geometric characteristics."

Jan 1, 1996

By Peter Godbehere, Christian Desroches, Viken Baboudjian

"Noranda Copper Smelting and Refining is a unit of Noranda Metallurgy Inc., comprising the Home smelter in Rouyn-Noranda, Quebec and the C.C.R. Refinery in Montreal East. The Home smelter provides custom smelting services for a wide variety of copper and precious metal bearing concentrates and recyclable materials, producing over 200 000 tonnes of anodes and 450 000 tonnes of sulphuric acid annually. The C.C.R. Refinery has an annual production of 360 000 tonnes of copper cathode, and is a major refiner of precious metals.Over the past twenty years, Noranda Copper has developed innovative processes and operating techniques to treat the ever increasing complexity of primary feed materials, while improving the quality of its final products, working conditions and reducing environmental emissions.This paper presents an overview of the operating practices of Noranda Copper with particular emphasis on the impact of impurities in the smelting and refining processes.IntroductionThe treatment of custom materials has been practiced by Noranda Copper since commencement of operations at the Home smelter in 1927 and the CCR refinery in 1931. Copper concentrates from a wide variety of regional, North American and overseas producers account for the bulk of the 800 000 tonnes treated annually, although recyclable and secondaries have increased in importance as feed sources in the past two decades. The geographical disadvantage of the Horne smelter compared with most custom smelters located on tidewater has provided an important incentive for Noranda Copper to develop the necessary technology and operating practices at its smelter and refinery to treat high value complex concentrates and other feeds containing significant concentrations of bismuth, antimony, arsenic, lead, tellurium, mercury, etc."

Jan 1, 1995

By W. D. Robbson

DR. G. W. RAMSEY (l): A study of our non-treatment silicosis autopsy material for the years 1940-43 inclusive, in addition to the common findings of fibrosis, nodules, and emphysema, shows marked thickening of the alveolar walls. This change is due to one or more of the following factors: congestion, edema, accumulation of both small and large monocuclear cells within the interstitial tissues and large monocuclear cells attached to the lining membrane of the alveolar sacs. This alteration in the alveolar walls, we believe, is one of the most important factors in producing impaired pulmonary function. Comparison of our first autopsy material of a case receiving twenty aluminium treatments beginning June, 1943, shows a striking change in the alveolar walls. In all areas free of silocotic nodules and fibrous tissue, the alveolar walls approach normal thickness and are free of cellular deposits. No change was noted in the old processes and none was expected. We believe that these changes in the alveolar walls were brought about by the aluminium therapy and that they constitute a major factor in the improved pulmonary ventilation noted in treatment cases.

Jan 1, 1945

By Bevan. P. A.

The general location, topography and climate are discussed briefly, together with an historical record of the deposit. General geology, grade control and ore reserves are covered at some length, and reasons are given for the operation being placed on a salvage basis.

Jan 1, 1973