Search Documents

By J. Duriez, L. Scholtès, F. V. Donzé

"Fracture propagation process in brittle rock is investigated by means of numerical simulations performed with an adapted formulation of the discrete element method. The progressive failure mechanism is simulated through the breaking of the bonds making up the cohesion between the elements constituting the simulated medium. The use of appropriate contact laws associated to a near neighbor interaction feature provide the model the ability to reproduce fundamental characteristics of brittle rock behavior such as, for example, high values of the tensile to compressive strength ratio. Great attention is given to accurately describe the properties of the pre-existing joints or faults in the model. A specific joint model gives the possibility to define a tailor-made behavior of the discontinuity surfaces without suffering from discretization bias.Compression test simulations are performed on pre-flawed samples and compared to experimental results in order to validate the numerical approach for describing the initiation and propagation of fractures in brittle rock under mode I+II loading. It is shown that the crack mechanical parameters can greatly influence the fracturing pattern, in particular its frictional properties. Overall, the numerical simulations reproduce fairly well the failure patterns that are obtained experimentally.The discrete model is then used to study mode I+III loading to give an insight into fracturing problems occurring at the scale of the continental crust. The ability of the model to support mechanically the physical modelings performed with wet clay or sandbox is shown. As an example, the model is used to track the development of a twist crack system (wrench fault) through the nucleation and coalescence of microcracks."

Jan 1, 2015

By Jaeheon Lee

"Biooxidation of gold ores or concentrates could be a very attractive alternative to pressure oxidation (POX) or roasting to liberate the gold grains from various sulfides. Crushed heap bioleaching was successful in US and many operations using tank bioleaching of gold concentrate are currently running around the world. Many parameters need to be considered during the project of sulfidic refractory gold ore process. Capital and operation costs are among the most important ones. Run-of-mine heap biooxidation could be very inexpensive and the smaller the crush size (particle size), the more expensive the capital and operating costs for biooxidation application are expected. The capital cost of biooxidation could be a fraction of the cost for building POX plant or roaster and the operating cost could be 1/3 of POX or roasting depending on the method utilized. A new biooxidation process, Sand Farming, is introduced as an alternative to POX and tank biooxidation process. A relatively coarser particle size (P80 = 650 µm) of the process benefits the low cost of grinding against the conventional grinding size (P80 = 75 µm) for other options. The cost of Sand Farming is less than 40% of that of pressure oxidation with comparable gold recovery from the downstream process. This paper will review the laboratory scale testwork for various biooxidation process of sulfidic refractory gold ores and concentrates and provide the economic evaluation showing the biooxidation could be the most economic method without much sacrificing the overall gold recovery. INTRODUCTIONThe decreased availability and lower grade of raw materials has motivated industries to consider recovering values utilizing low cost process options. The process may treat high grade concentrates or submill grade ores that cannot be processed economically by conventional milling-flotation or leaching. Sulfidic refractory gold ores/concentrates have been economically processed by roasting, pressure oxidation, and biooxidation in stirred tank reactor. The process selection is based on a series of studies including multi-year long ore characterization and metallurgical investigations."

Jan 1, 2016

By Y. A. Topkaya

In this research work, a process was described for the recovery of copper and zinc in copper converter flue dust from the Black Sea Copper Works' Samsun Smelter Plant. After characterization of a representative flue dust sample, the process included roasting of the flue dust and then leaching in dilute sulfuric acid solution. Roasting time and temperature were studied to determine the optimum roasting conditions. Sulphuric acid concentration, duration, temperature of leaching and solid to liquid ratio were the parameters studied in the bench scale laboratory leaching experiments.

Jan 1, 2007

By F. S. Thurner

This paper, a description of the new ore-unloading and stockpiling facilities at the Sydney Works of DOSCO Steel Limited, deals with a new approach to arrive at the most economical solution to combine ore unloading facilities for common bulk carriers and for different types of self-unloading vessels. Also discussed is the design and installation of a 1-mile-long steel-cord belt conveyor sys-tem with a most modern type of mobile belt conveyor stacker, along with automatic and semi-automatic controls for the entire ship-unloading and stockpiling operations.

Jan 1, 1968

By Somasundaran P., M. Vasudevan, Z. Dai, D. R. Nagaraj, T. Bhambani, P. Patra

Historically, efficient beneficiation of ultramafic ores has been challenging, partly due to a lack of clear scientific understanding of the effects of Mg silicates, particularly fibrous serpentines, on selective Ni recovery. Recent research at Columbia-Cytec as a part of a Vale JDP project has led to new insights into the mechanistic aspects of the adverse effects of Mg silicates. Our research has provided strong evidence to support the hypothesis that the adverse effects of Mg silicates are mediated through their large influence on pulp rheological properties, far more than any other pathway. The severity of the effect of Mg silicates is predominantly dependent on the aspect ratios of Mg silicates. For example, the pulp viscosity increases dramatically with increase in the fibrous nature of the gangue mineral leading to poor Ni separation. Various ways by which the suspension rheology affects flotation sub-processes, with implications for remedy are discussed. The insights and results have served to develop (or construct) a phenomenological model to adequately explain all of the ore flotation data, particularly the Mg silicate transport to the froth phase and the concentrate.

Jan 1, 2011

Most of automotive magnesium applications are presently produced by high-pressure die casting processes, For further expansion of the alloy usage in automobiles, novel-manufacturing processes needs to be developed, In this study, squeeze casting of AM50 alloy was carried out using a hydraulic press with an applied pressure of 70 MPa, Tensile properties and fracture behavior of the squeeze-cast AM50 were characterized in comparison with the die cast counterpart, The squeeze-cast AM50 alloy exhibits virtually no porosity in the microstructure evaluated by optical microscopy, The results of tensile testing indicate that the improved tensile properties for the squeeze-cast samples over the conventional high-pressure die-cast parts, The analysis of tensile behavior shows that the strain-hardening rate during the plastic deformation of the squeeze-cast specimens is constantly higher than that of the die-cast specimens. The SEM fractography evidently reveals the ductile fracture features of the squeeze-cast alloy AM50.

Jan 1, 2005

By Ruan Chi, Zhenyue Zhang, Zhengyan He

In order to understand what governs the leaching of exchangeable rare earth (RE) and impurities and enhance the RE leaching process, the effects of the concentration of ammonium sulfate, pH and leaching temperature on the migration of RE and aluminum (Al) during the leaching of weathered crust elution-deposited rare earth ore was studied. The elution curves for ammonium ion (NH4 +) were also studied to reduce the consumption of the leaching agent. It was found that a high concentration of leaching agent can enhance the leaching process of RE and Al, reduce the breakthrough volume of NH4 + and more rapidly obtain the equilibrium of NH4 +. However, excessive leaching agent can both increase the cost and the burden on the environment. There is almost no variation on the elution curves of RE and Al in the pH range of 4-8 and control of the pH of the leaching agent can be omitted. It is better for the leaching work to be done in summer since higher temperatures can enhance the RE leaching process and improve the use ratio of ammonium. Using 0.1 mol/L ammonium sulfate for leaching 250 g RE ore, 95.42% RE extraction can be obtained when the volume of leachate is 102.6 mL. At this moment, only 18.17% of NH4 + is used to exchange RE and 49.22% of NH4 + is left in the leachate that can be reused as leaching agent by replenishing ammonium sulfate. The results of our studies can provide theoretical guidance for high efficiency and low consumption exploitation of RE ores.

Jan 1, 2016

By G. B. Hobbs, S. Saimoto, L. Collins

"Plastic yielding and flow in metals is dependent on the microscopic process of simple shear along crystallographic planes and directions known as slip. Thus, by altering the crystallographic direction of the stress axis or placing constraints in the direction of plastic flow, anisotropy of yield strength for the same material is observed. This phenomenon is called texture strengthening. The application of this concept to highly anisotropic crystal structures such as the hexagonal group of titanium and zirconium alloys, the former in missile casing and the latter in nuclear reactor fuel tubing, seems obvious. The outstanding example in cubic structures is the case of deep-drawing steel. The R value, the width strain over the thickness strain during a tensile test, is taken as a measure of texture strengthening. In face-centred cubic structures, texture strengthening has been completely ignored on the basis that materials with R less than one are not amenable to this beneficiation. This study will review two aspects of texture which will lead to strengthening, first the thermal stability of the deformed microstructure, which is dependent on the stress axis, and second, the texture strengthening aspect of fcc metals.A review of recovery and recrystallization in textured aluminum wires, copper and cupro-nickel sheet will be presented with the view of extending these concepts to the manufacture of heat-exchanger tubing. The superior creep properties of specially processed commercial products such as TD-Ni, TD-NiCr and MAR-M200 will be shown to be a manifestation of the same physical phenomena."

Jan 1, 1981

By R. S. Douglas

Introduction The mine at Copper Mountain of the Granby Consolidated Mining, Smelting and Power Company was one of the pioneers in the use of blast-hole diamond drilling for ore breakage. This method of mining has now been brought to a high degree of perfection. The system in use has?been described in a previously published paper which has become an important part of the literature o the blast-hole drilling method. At the time of the establishment of the system at Copper Mountain, standardized loading and drilling procedures were set up. These procedures were based partly on the results of experiment and partly upon the judgment of men experienced in breaking rock in the mine. The success of the method has been proof of their adequacy. With the progress of scoping in the mine, the diamond drill method of breaking was applied to other ore blocks where different conditions obtained. It was found necessary to make adjustments in the standard procedures to get the best results under the new conditions. The following paper attempts to express, in terms of mathematics, the relations of the variable factors. Until recently, estimations of drilling required were based upon the tonnage to be broken and the proposed rate of explosive loading. A revised method of estimating is outlined below which is direct and which involves no unrelated variable factors.

Jan 1, 1947

By Andrew Cormier

"The Early YearsThe Grand Lake coal fields in New Brunswick undoubtedly can claim the distinction of being the first part of North America from which coal was mined and exported. The diaries of the Governor of Massachusetts during the first half of the 17th century clearly establish this fact. There is also a reference in the Massachusetts Colonial Records which indicate that coal exports to New England were carried on as early as 1639.It has generally been believed that Cape Breton mined and exported the first coal; but no account has yet been found to show that this took place earlier than 1676. Both at Grand Lake and Cape Breton the coal was near the surface and removed by hand.When the country passed entirely into British control, Joseph Garrison, a grantee of Maugerville in 1765 moved to Jemseg. While surveying the north side of Grand Lake he discovered outcroppings of coal on the shore of the lake and further inland along the banks of streams. It was he who named Newcastle Creek in reference to Newcastle in England, which was widely known for its coal mines. Joseph Garrison died in 1783, the same year that an influx of United Empire Loyalists increased settlement in Newcastle Creek in the area now known as Minto. Many Loyalists also settled on the shores on both sides of Grand Lake.At a number of points where streams cut channels through the overlying strata, the coal seams were exposed and it was at such outcroppings that the early operations were carried on. A tunnel was driven in the seam from the foot of the bank, affording both an outlet for the coal and natural drainage from the workings. The coal was loaded into boxes and wheeled over wooden tracks to a point on the surface where it could be dumped into wagons and hauled either direct to destination or to where it could be loaded into boats and conveyed via Grand Lake, Jemseg and Saint John river to points of distribution.In the latter part of the 18th century and first years of the 19th century, farmers were undisturbed by mining the coal found on their lands. This was soon to change and resulted in many years of contention between landowners and the Legislative Assembly.New Brunswick became a separate province from Nova Scotia in 1784 and the seat of government moved from Saint John to Fredericton in 1788. The new province had its first priorities; the establishment of counties, the building of roads, and the development of its natural resources. From 1805, records of coal and land development are fairly complete. These records show the increasing interest of the Province in developing the coal fields. This interest resulted in the granting of coal leases to many friends of the government, without any regard for the wishes of the farmers who owned and had occupied the land for many years. The farmers fought back with lawsuits and other forms of dissension but with little success. By the end of the 19th century there were very few farm operators left in the area."

Jan 1, 1992

By H. A. Kishawy, S. Kannan, M. Balazinski

Metal Matrix Composites (MMCs) are new generation engineering materials that possess superior physical and mechanical properties compared to nonreinforced alloys. However, the presence of abrasive ceramic reinforcements in the ductile matrix causes severe tool wear and premature tool failure. Flank wear was found to be the dominant wear mode while the main wear mechanism was abrasion. Analysis of the cutting tools using scanning electron microscopy has shown that both two body and three body abrasion are operational during machining MMCs. A methodology for predicting the tool flank wear progression during bar turning ofMMCs was presented in an earlier paper [1]. In the proposed model, the wear volume due to two body and three body abrasion mechanisms was formulated. Then, the flank wear rate was quantified by considering the tool geometry in 3D turning. The main objective of this paper is to investigate the contribution of two body and three body abrasion towards the tool wear volume during cutting MMCs.

Jan 1, 2006

By Free. Michael L.

Crushing ore prior to heap leaching enhances mineral liberation and creates fine particles that may require agglomeration to avoid permeability problems during leaching. Conventional modeling is relatively successful in describing general fluid flow and extraction in heaps. However, most models do not adequately account for the effects of mineral liberation and exposure or the effects of agglomeration, curing, and loading on heap leach performance. This paper will discuss methods to account for mineral liberation and exposure as a function of comminution. It will also discuss methods for incorporating liberation, exposure, and mineral locking as well as curing and fluid flow in heap leach modeling. It will also provide information regarding agglomeration and the effect of loading in heap leach modeling.

Jan 1, 2014

By S. K. Paul

"This paper briefly describes the underground crushing and conveying system at Sherritt Gordon Mines' Ruttan Mine. A series of three steel-cord belted conveyors, with a total length of 2J55 metres and a total vertical lift of 407 metres, convey the muck from the underground crushing station to the mill at the surface. The maximum size of the crushed rock is 6 in. All the conveyors are provided with numerous safety and fire suppression devices. IntroductionThe Ruttan Mine of Sherritt Gordon Mines Limited is located 20 km east of the town of Leaf Rapids, 760 km north of Winnipeg. The orebody is multilensed, with lens width varying from 6 to 45 m. Ore production started in 1973 with the opening of a 10,000-tpd open-pit mine. Initial development of the underground mine was started in 1972 with the driving of parallel conveyor and access declines at minus-2507o gradient to the I 220-m level, and then the access ramp was further extended to the 1160-m level. Exploration drifting was done on the 1280-m and 1160-m levels from the access ramp. The final development plan for the underground project was approved in January 1977, and full-scale development and constructionwere resumed.At present, Ruttan Mine is in a period of transition from open-pit to underground mining. Ore production is now coming from both operations. By mid-1980, open-pit production will cease and all production will come from the undergroundmine.The underground mining method at the Ruttan Mine is sublevel open stoping with delayed backfilling. The orebody is divided along strike into a series of 27-m-long stopes and 15-m pillars, both 60 m high."

Jan 1, 1980

By P Kovacs, D. L. Flock

For the purpose of reservoir-performance calculations a balance can be made between the materials with-in the reservoir and the production from the reservoir. The material balance equation, a relationship which holds under or near equilibrium conditions, has been used in many forms by the Petroleum Engineer for the determination of initial oil-in-place in the reservoir and the calculation of performance into the future. One of the more recent methods developed by Tracy, utilizes a modified form of the Schilthuis material balance. In the latter case, values of incremental production are assumed for a particular pressure drop, a value of the gas-oil ratio found and a check of this estimate made by calculation"' the initial oil-in-place. Tracy's method utilizes an estimation of the instantaneous gas-oil ratio and by trial and error a value of the gas-oil ratio is

Jan 1, 1961

By J. Currie, J. McManus, R. Chenier

"Cominco Copper Division's Valley Mine is located in the Highland Valley of British Columbia, approximately 275 km by air northeast of Vancouver. The nearest towns are Logan Lake, located IS km to the east and Ashcroft, located about 50 km to the northwest.Preproduction stripping of rock and overburden at the Valley Mine's Lake Zone Pit began in mid-1982 following a decision to discontinue mining in the adjacent Jersey Pit. Equipment and mining methods were carried over from the Bethlehem Copper operations which, with Valley Copper Mines, were merged into Cominco in December 1982.Blasting practices, as carried over from the Bethlehem pits, were designed to provide the fine fragmentation required to meet production requirements using the Bethlehem crusher. However, after mining the first few benches of the Lake Zone Pit, it became apparent that overblasting at the pit limits was causing a number of bench failures, as well as contributing to an over-all reduction of the material strength of the rock mass forming the southwest wall of the pit.With present ultimate pit plans calling for the southwest wall to be as high as 300 m, Valley staff realized that potential slope stability problems should be dealt with as early as possible. This philosophy would enable experimentation on phase pit walls in order to attain the optimum slope angle on the ultimate pit wall.As part of an over-a ll slope stability program, a controlled blasting program was initiated at the Lake Zone Pit in March 1983. In this program, Valley engineering and production staff worked together with Golder Associates in establishing design criteria and evaluating the results. This program resulted in a marked improvement in the soundness of pit walls while maintaining the required degree of fragmentation."

Jan 1, 1985

By K. Thuro, B. Sellmeier, M. Krautblatter

"Recent rockfall events, like the Tramin rockfall at January 21st, 2014, underline the significance of a comprehensive hazard assessment. A common way of estimating the hazard along infrastructure is the performance of run-out modelling using 3D rockfall codes like Rockyfor3D or RAMMS::Rockfall (Dorren, 2010, Bartelt et al., 2013). The potential block volumes are often roughly estimated from talus material and an overview of the source area, where the magnitude assessment is usually physically and intellectually demanding. Nevertheless especially for increased magnitudes, the volume estimation is crucial in terms of hazard analysis. Mid-Magnitude-Events exceed the load capacity of the most mitigation measures and their date of failure is hard to predict. Here we define the term Mid-Magnitude-Events as block volumes between boulder falls (10-100 m³) and block falls (100-10,000 m³) (Whalley, 1984).The current contribution provides an approach of integral process analysis for a 200 m3 carbonate block above the federal road B 305 near the city of Salzburg in the Bavarian Alps, Germany. We performed detailed analysis of the critical carbonate block exposed to planar failure. The block volume and the dimensions of the failure surface were mapped in detail, due to the unique occasion of an accessible failure surface. The discontinuity persistence was recorded to assess a minimal degree of fragmentation for a potential failure scenario. A maximum degree of fragmentation was estimated due to recording of block dimensions at the talus slope resulting from frequent rockfalls.We performed parameter studies in terms of run-out modelling using the code RAMMS::Rockfall (Bartelt et al., 2013), taking the recorded data for block fragmentation into account. In our contribution, we aim to demonstrate a comprehensive approach for hazard assessment of mid magnitude rockfalls, taking detachment processes, fragmentation and run-out analysis into account."

Jan 1, 2015

By D. R. Hatton

To obtain sufficient material on which to perform copper-molybdenum separation testwork a variability set of drill hole reject samples amounting to several tons was put together to include the different ore types proportions expected in the copper circuit. The samples were treated in a copper circuit pilot plant and enough mass of bulk concentrate was recovered to conduct copper moly separation tests in the laboratory. Tests consisted of stage flotation reactor (SFR) rougher pilot plant tests, conventional laboratory rougher, cleaner and 4 stage open circuit cleaner tests. The mineralogical liberation analysis of the feed and concentrate was used to model the effect of liberation on the grade-recovery relationship of the different samples. Mineral kinetic parameters for the various samples were determined by calibration to the test data. The copper concentrate results as simulated from previous studies on the same deposit were used to simulate the variability in head grade and throughput expected for the feed to the copper molybdenum separation circuit for each of the first 10 years of production. This variation in feed was then simulated through the separation circuit to obtain optimised molybdenum grade recovery curves to forecast the circuit production for each of the first 10 years. INTRODUCTION Incorporating Geometallurgy into the design for a copper molybdenum separation is especially challenging due to the low mass of final concentrate typically produced during testwork. This is due to the low molybdenum head grades and high overall molybdenum upgrading expected. With molybdenum head grades of around 300 ppm, 1 tonne of copper circuit feed is expected to produce around 300 g of molybdenum concentrate in the plant. In the laboratory however, this may end up only resulting in a few grams. Obtaining sufficient mass for laboratory testing therefore requires starting with a large initial sample and careful testwork planning to maximise the utilisation of this mass. A testwork program was designed to investigate the effect of ore variability on the copper molybdenum separation circuit (here after referred to as the molybdenum circuit). Composite samples were selected to represent the various ore types, copper content, moly content, pyrite content and clay contents expected in the copper circuit feed. These samples were run through a bulk copper pilot plant to create the feed for the molybdenum testwork. The molybdenum testwork consisted of rougher kinetic flotation tests, rougher cleaner kinetic tests, rougher cleaner kinetic tests with regrind, stage flotation reactor (SFR) pilot plant tests, open circuit cleaner tests. These tests were used to calibrate the ore kinetics in the IGS-FLEET model for simulation of the molybdenum circuit performance.

Jan 1, 2019

By Peter Moon, Lloyd G. Campbell

"How well supervisors supervise, and are supervised determines whether management's goals will be reached and ...how effective the work force will be... Upper management must recognize the potential returns of viable training programs for both management and mine workers… The key to performance, from the standpoint of safety and productivity, is the ability of the line supervisor to manage(1).In this article, the authors will share their experiences in supervisor selection and development. They also draw on the work of two men in particular, Douglas Bray and William Byham, both of whom have contributed significantly to the understanding of supervisory development and training.IntroductionYears ago, there was not much training for supervisors. They worked under an authoritarian style of management and modelled themselves on it. They were generally selected for their skill as miners, mill operators or mechanics. Things have changed. Today, companies have different needs. The selection of supervisors is far too important to rely on guesswork. Progressive companies want supervisors who think like managers - supervisors who know how to plan and organize, set performance standards and monitor them, analyze problems, develop solutions, show sound judgment and deal effectively with people. The evaluation of these supervisory ""dimensions"" is best accomplished through the use of an assessment centre. The Assessment Centre Method increases the accuracy of predicting the future success of candidates being considered for promotion.Mining and other resource companies use assessment centres to select the most suitable people for supervision. The Assessment Centre Method is based on extensive research. It eliminates hit-and-miss selection methods by using several different exercises that simulate the problems and activities that candidates would face if they were promoted into supervision . In other words, they get a realistic "" sample"" of the supervisor's job and are required to deal with and manage interpersonal and problematic circumstances."

Jan 1, 1990

By Chris V. Sellathamby

Condition-based maintenance is replacing preventive maintenance in many industrial operations as a result of gains in productivity. Preventive maintenance is strictly time-based which means that as long as the prescribed time is sufficiently short, failures are prevented. The trade-offs between shorter cycles and increased downtime is a fine balancing act. Condition-based maintenance is gaining momentum as the more cost-effective and green solution to finding the optimal maintenance cycle and improving overall productivity. In the mining industry, various parameters of heavy equipment are monitored continuously to provide feedback for maintenance events. However, strain, shock, and vibration, key factors which lead to yielding and fatigue of metal parts, are not generally monitored by built-in systems, mainly due to the complexity of sensor installation and computational intensity of data processing. Scanimetrics has developed a stand-alone, add-on wireless system for measuring strain, shock, and vibration in heavy equipment and components, the data from which can be directly used to trigger maintenance events. The present system is being deployed in tar sands mining equipment. The system consists of a portable display and control unit, a software platform consisting of data management, sensor instrumentation and data analysis, and wireless strain sensor units, which can be easily installed on equipment. Data from the sensors can be gathered throughout the mine site, processed instantly, and used to generate condition-based maintenance events, improving overall uptime of the equipment and overall productivity of the mining operation.

Oct 1, 2010

By J. Y. Kim

This paper presents a novel action recognition method for observing human workers using interactions between actions and related objects on an internal construction site. This method can be used to measure work rates for labour productivity monitoring. This monitoring is critical because the performance of a construction project is significantly impacted by labour productivity. However, construction sites are generally crowded with a large number of workers and objects. Such congestion disrupts the accurate, automatic recognition of construction workers? actions. This congestion is one reason that existing automatic action recognition studies of construction areas mainly focus on workers? actions themselves. However, the crowded conditions mean that sites could offer a great deal of clues that could be used for automatic action recognition. According to psychological studies, interactions clearly take place between human actions and related objects, such as between hammering and a hammer. Humans use these interactions to recognize actions or objects more accurately. On the construction site, workers, materials, tools, and equipment are carefully planned out ahead of actual construction. The categories of workers and objects are pre-defined and, as noted, specific interactions define relations between worker actions and objects. In this paper, the interactions are limited to human workers and their hand-held objects. Action recognition results can be combined with hand-held object information to improve recognition accuracy. With the limited interactions, experiments in this paper show a significant improvement in action recognition. This paper describes the utilization of these interactions to improve construction action recognition accuracy based on human skeleton data and 2D color video from Microsoft KINECT sensor.

Aug 1, 2013