Search Documents

By T. Hidayat

The distributions of minor elements between slag/metal and slag/matte in equilibrium with tridymite in the Cu-Fe-O-S-Si-Al-Ca system have been investigated in the range of conditions of interest to the high- temperature copper production, refining, and recycling processes. An improved experimental methodology has been used involving high temperature equilibration in controlled gas atmospheres, rapid quenching, and quantitative microanalysis techniques using Electron Probe X-ray Microanalysis (EPMA) and Laser Ablation Inductively Coupled Plasma Mass Spectrum (LAICPMS). The effect of oxygen partial pressure on the distributions of minor elements between slag/metal and slag/matte has been accurately measured. The effects of slagging components (Al2O3 and CaO) on the distributions of minor elements between slag/metal have also been experimentally determined. The present study is a part of a larger integrated experimental and thermodynamic modelling research program in the systems relevant to high-temperature copper processing. INTRODUCTION In the high temperature processing of copper, minor elements are distributed between different phases, i.e. liquid slag, liquid matte, and liquid metal. From a processing perspective, it is desired to have the valuable minor elements distribute predominantly in the metal and matte phases rather than in the slag phase, and to have the non-valuable minor elements distribute predominantly in the slag phase rather than in the metal and matte phases. Knowledge of the distributions of minor elements between phases in the smelting, converting, and refining processes is required if the distributions of minor elements between phases in these processes are to be optimized.

Jan 1, 2019

By Zhibao Li, Lanmu Zeng

The behavior of dicalcium silicate in NaOH-NaAl(OH)4-Na2CO3 solution is of significance for controlling the silica level in the production of alumina via the sintering process. Dicalcium silicate samples were obtained through a twostep approach: coprecipitation of calcium and silicate from CaCl2-Na2SiO3-NaOH solutions; and calcination of the hydrated precursor at 1200°C for 4 hours. The optimization of the synthesis parameters including temperature, solution concentrations and aging time was also investigated. Xray diffraction (XRD) and chemical analysis show that the calcined solids include dicalcium silicate with trace amounts of wollastonite. The solubility of the synthesized dicalcium silicate in HCl, NaOH, mixed NaOH-NaAl(OH)4 and NaOH-NaAl(OH)4-Na2CO3 solutions was determined. It was found that the solubility increases with increasing HCl and NaOH concentration. The effect of temperature on the solubility in HCl solutions is limited, but the solubility decreases with increasing temperature in NaOH solutions. The solubility of dicalcium silicate in NaOH-NaAl(OH)4 and NaOH-NaAl(OH)4-Na2CO3 solutions was shown to increase with increased temperature, Al(OH)3 and Na2CO3 concentration. The BromleyZemaitis model for the aqueous electrolyte system was selected to predict the solubility of dicalcium silicate. The model’s predictions yielded certain success compared with experimental solubility data.

Jan 1, 2014

By Robert B. Parsons

"Next month will mark the anniversary of the release of an important federal study on a mineral policy for Canada. The study, entitled ""Mineral Policy-A Discussion Paper"", provides well-researched coverage of a broad range of issues that are of interest to the mining industry. Unfortunately, there is a real possibility that the discussion paper will wither and die on the vine, unless the federal and provincial governments, and the private sector, collectively ensure that some of the key considerations which are raised by the paper are acted upon.IntroductionAlmost one year ago, on March 8, 1982, Federal Mines Minister July Erola released an important study entitled ""Mineral Policy-A Discussion Paper"". The discussion paper, which presents the government's assessment of the opportunities and constraints facing the Canadian mineral industry in the 1980s, was prepared within the context o f three principal objectives-strengthening the resource base on which the industry rests, ensuring the adequacy of research activities needed to support development of the resource, and furthering the development of markets for the resource It is clear that, in today's economic climate, not even the most generous incentives would turn the industry around: what is needed is a sound base for future development, when this is possible. In this regard, the discussion paper is an excellent stepping stone, in that it reviews a wide range o f fundamental policy issues which touch on all facets o f the mining industry."

Jan 1, 1983

By Robin N. Adair

The Halfmile Lake stratiform volcanogenic massive-sulfide deposit consists of pyrrhotiterich breccia-matrix sulfides and pyrite-pyrrhotite-rich layered sulfides that form a laterally continuous sheet stratigraphically underlain by an extensive pyrrhotite-chalcopyrite-quartz stringer zone. Mineralization is hosted by a sequence of felsic pyroclastics and volcanic-derived, fine-grained metasediments. The proportion of volcanic to sedimentary rocks indicates increasing vent proximity from southwest to northeast across the deposit area. Fine- to medium-grained felsic pyroclastics and roughly equal amounts of fine-grained metasediments comprise the stratigraphic footwall to the mineralization. Quartz-feldspar porphyritic bodies cut this sequence and may have provided the heat source for exhalite activity. Felsic tuffs, locally crystal-rich, and lesser amounts of metasedimentary rocks make up the immediate stratigraphic hanging wall. This sequence is stratigraphically overlain and locally interfmgered with mafic volcanics that contain substantial proportions of felsic fragments. Deposition of sulfides post-dated the beginning of felsic volcanism, which places the deposit in the middle of the Lower Tetagouche Group. Compositions of the volcanic rocks range from basalt to rhyolite and exhibit sub-alkaline affinities. Strongly overprinted whole-rock, trace-element, and REE geochemical signatures resulting from mineralizing hydrothermal activity confirm the genetic relationship between the stringer zone and the mineralized sheet. Large-scale D1 folding has overturned the entire sequence. D1 thrust faults and related sheath-like folds have profoundly affected sulfide distribution. D2 is manifested by a penetrative S2 foliation, and D3 is represented by large-scale open folds.

Jan 1, 1992

By Shamia Hoque, Charles Q. Jia

Smelter slags contain valuable metals such as Co, Ni and Cu in proportions of less than 1 wt% along with about 40 wt% of Fe and 15 wt% of Si. Although aqueous SO2 is a versatile lixiviant for transition metals, dissolving the slag in aqueous SO2 produces solutions in which Co and Ni concentrations are lower than that of Fe due to the low metal/ Fe ratio in the slag. To develop the options for increasing Co and Ni concentrations the solubility of slag in aqueous SO2 was studied experimentally and theoretically using OLI, a software package for simulating electrolytes chemistry. The modeling results correlated well with experimental results. The model suggested that the species dominating the system was FeSO3, which would precipitate out as FeSO3.3H2O when the concentration of Fe+2 reached 1.22 molal and the concentration of S032- was beyond 1.4 molal. In the experiments the influence of pH and solids loading were studied. The leach solution obtained after dissolution of slag at 50% solids loading had a pH of 1.85. On raising the pH to 3, precipitation occurred. Analysis of the solution collected after the addition of alkali showed over 50% reduction of Fe, Co and Ni. XRD analysis revealed the precipitate to be of amorphous nature due to the silica present. The analysis confirmed that the precipitate was mainly FeSO3.3H2O. The paper also discusses the potential impact of the slag on the environment.

Jan 1, 2004

By E. Ghali, N. Sorour, G. Houlachi

"The binary Fe53Mo47 and ternary Fe54Mo30P16 coatings have been electrodeposited from citrate-based electrolyte on mild steel (MS) substrates. The electrodeposition has been conducted for 6 hours at 20 mA cm-2 and 30°C. The electrochemical tests were carried out in chlorate solutions containing 300 g L-1 NaCl and 4 g L-1 K2Cr2O7 at pH 6.4 and 80°C. A number of surface characterization techniques such as SEM-EDS, XRD and EMP were used to study the microstructure of the alloys. The electrocatalytic activity of these coatings was investigated using steady-state polarization and galvanostatic technique. This study revealed that the Fe-Mo-P coating could be considered as a promising cathode material for the hydrogen evolution reaction (HER). The results showed an important decrease of hydrogen overpotential for Fe-Mo-P alloy as compared to that of Fe-Mo and especially MS which is a traditional cathode in chlorate industry. The HER overpotential for Fe54Mo30P16 at current density of 250 mA cm-2 was decreased by 30% in comparison to that of MS (1029 mV), and by 16.5% to that of Fe53Mo47 coating (857 mV).INTRODUCTIONSodium chlorate is used for manufacturing of several daily consumption products. This chemical is mainly employed for the production of chlorine dioxide (ClO2) that is a bleaching agent used in the pulp and paper industry. The ClO2 is also consumed for generation of perchlorates, chlorites and other chlorates, as an herbicide and in uranium processing (Cornell, 2002). Sodium chlorate is produced industrially via following overall formula in un-divided electrochemical cell (Nylén & Cornell, 2009):"

Jan 1, 2016

By A. D. Mufch, G. P. Mitchell

"THE HARDY MINE of Falconbridge Nickel Mines Limited is located in Lot 9, Concession 1, Levack Township, Sudbury District, Ontario, 20 miles northwest of the city of Sudbury, and a mile west of the town of Levack. The ore deposit is one of the many nickel-copper sulphide bodies found on, or near, the lower contact of the well-known Sudbury norite-micropegmatite irruptive, and is one of a family of ore deposits which occur on the northwest rim of the irruptive.The property was acquired by purchase in 1935. In the same year a magnetometer survey along the footwall contact of the norite, which is covered by about 150 feet of glacial sands and clays, first indicated the location of the orebody. Drilling from 1935 to 1942 outlined the extent of the ore. Shaft sinking was commenced in the fall of 1951, and the mine is now approaching full production at a rate of about 300,000 tons per year.There are several major differences between the geology of the Levack area and the Falcon bridge area, which lies at the opposite extremity of the irruptive, 28 miles to the east. The purpose of this paper is to describe the essential features of the geology of the Levack area as seen in the Hardy mine, and to supplement the recent papers on other properties in the Sudbury area by Davidson (1), Lochhead (2), and Yates (3).General GeologyA recent review of the regional geology and an extensive bibliography of the Sudbury area can be found in the two papers by H. C. Cooke (4, 5). Some of the recent related references are: Jas. E. Thomson (6), E. M. Abraham (7), Franc. R. Joubin (8), W. G. Q. Johnstone (9)."

Jan 1, 1949

By Roger M. Nendick

"IntroductionThe stages of development for bringing a mill into production demand that a flowsheet for the process be developed at an early stage. Detailed engineering of the mill may then proceed without duplication of engineering effort on alternative processes. In the case of gold and silver mills, several process alternatives exist which must be evaluated before the flowsheet is finally fixed. The recently developed Carbon-in-Pulp process has added to this choice.Clearly, the major factor in determining the most suitable process is the amenability of the particular ore to a given treatment. Other factors that will also influence the choice are location, climate, power and water supplies, and available capital.Gold and silver milling processes can be divided into three main types:Gravity Concentration;Flotation;Cyanidation.Combinations of the three are frequently used; i.e. flotation followed by cyanidation of the concentrate, or gravity concentration in the grinding circuit with cyanidation of the classifier overflow. The following are the salient advantages and disadvantages of the three main alternatives.Gravity ConcentrationGravity concentration is suitable for free-milling gold ores, i.e. ores in which the gold is relatively coarse and free from sulphides. It should be noted that just because an ore is high grade, it is not necessarily free milling.Gravity concentration methods include jigs, shaking tables, spirals and more recently Reichert cone concentrators. All methods exploit the density difference between gold, which has a specific gravity greater than 15, depending on how it is alloyed, and the gangue, which usually has a specific gravity range of 2.7 to 3.5.A concentrate grade of several hundred ounces per ton might be produced, but recoveries by gravity alone are generally low in comparison to other methods. For this reason, gravity circuits are usually used in combination with flotation or cyanidation circuits."

Jan 1, 1983

By Rodney G. Orr, Phil Robertshaw, Roland Loewer, Klau Lehnert-Thiel

This paper documents the 1988 discovery and subsequent evaluation (to 1991) of diamond bearing kimberlites in the Fort à la Corne area, Saskatchewan, by Uranerz Exploration and Mining Limited. Cameco Corporation began participating as a joint venture partner (50%) in mid-1989. The first indications that kimberlite-type intrusions might exist in the area carne from Geological Survey of Canada aeromagnetic maps. Because of the overburden thickness (over 100 m), magnetometer surveys continue to be the main exploration tool in defining pipe locations and sizes. Magnetometer surveys in varying levels of detail have outlined one main cluster and two sub-clusters, the main group being some 10 km by 50 km in size. In excess of 70 individual targets have been interpreted from the magnetics as probably representing kimberlites. The size range of the individual magnetically-defined bodies is between 1 ha and 74 ha. Proof that the magnetic anomalies were kimberlite intrusions carne in 1989 when each of seven test holes, all drilled on different targets, intersected the potential diamond host rock. The majority of the targets tested were diamond-bearing, with the indicator mineral chemistries suggesting that both peridotitic and ecIogitic diamond parageneses could be expected. To date, 18 individual kimberlite bodies have been drill-tested. A total of 39 bulk samples, amounting to 186 t (representing 360 t of theoretical sample recoveries) were processed in 1990 and 1991. One hundred and sixty diamonds were recovered, averaging 0.04 carats in weight, the largest being 0.6 carats. Most of the bulk sample grades are less than 2 carats/loo t; only three bulk samples have higher grades, the best being approximately 10.5 carats/l00 1. The diamonds are predominantly gem-quality stones.

Jan 1, 1992

By G. Begin

"The expansion undertaken at Selbaie in 1985 necessitated an adaptation and expansion of the equipment maintenance system. This paper relates briefly the stages of transformation of the maintenance administrative structures, work methods and tools. The maintenance in a mechanized mine requires an expenditure level in the order of 20% of the total operating cost of the enterprise. Thus, the maintenance organization was modified to apply more computerized planning and follow-up, and the role of preventative maintenance was further advanced.IntroductionAs far as maintenance is concerned at Selbaie, the scenario described herein is a resume of the current situation. Although positive results have been obtained, this outline is in no way a detailed account of a fail-proof maintenance system.Once zone A-I was put into production, the expansion the mine experienced in 1985 had a direct impact on the equipment maintenance system. As centralized as it was in the beginning, the system is now partially decentralized.The over-all changes to the maintenance department demonstrate the flexibility required by organizations in new situations. In spite of the exceptional results obtained before the expansion, it became evident that both the maintenance and production sectors would have to be combined. In doing so, a more appropriate coordination of maintenance work could be obtained and the maintenance staff would obtain a more detailed knowledge of the equipment in each sector. In addition, by keeping the general and specialized departments centralized, it was possible to offset the negative effect s of a decentralized system, namely too much manpower."

Jan 1, 1990

By Jerry Z. Lu

Belt conveyor design involves the evaluation of belt tensions, drive selection, pulley configuration and other technical issues. The conveyor belt tensions vary with conveyor layout, drive pulley configuration, belt selection, and idler selection. The decisions for the belt conveyor construction always take all technical, commercial and maintenance issues into consideration. A good conveyor design shall provide required operational features and at the same time be cost effective. The common issues for an engineer to face during belt conveyor design include: (1) Conveyor drive selection ? drive with fluid couplings or variable frequency drives; (2) Drive system configurations - single pulley large drives or dual pulley smaller drives, if intermediate tripper booster drives shall be applied, what power ratio should be adopted for a multi-drive conveyor; (3) Gear reducers ? shaft mount drives, right angle gear reducers or parallel gear reducers; (4) Drive pulley lagging - ceramic lagging or rubber lagging; If ceramic lagging, what type should be used. (5) Conveyor speed variation ? If conveyors run at variable speeds, faster speed/lower percentage loading or slower speed/higher percentage loading. In many cases the decision maker find themselves in a dilemma ? technical benefits vs. financial benefits, capital cost vs. operational cost, and capital and operational cost vs. maintenance effort. Although many conveyor design topics above have been discussed in numerous technical papers and design reference books, management executives and inexperienced engineers may be confused and feel lost. The consultation of people around them may lead to different opinions since experiences tend to vary, making the decision making process complicated. The purpose of this paper is to simplify these complicated issues and provide useful guidelines for belt conveyor design. This paper focuses more on providing simple and practical answers and solutions instead of discussing each topic academically and theoretically in depth.

Nov 1, 2011

By J. Aydt, W. McCombe, H. McLaughlin, L. Nightingale-Mercer

The McClean Lake mill is located approximately 850 kilometers north of Saskatoon, Saskatchewan, Canada and is operated by Orano Canada Inc. (Orano). The mill was designed to process high grade uranium ores, and in 2014 completed a multiyear expansion to increase its production capacity to 24 Mlbs U3O8 per annum. This expansion included significant changes to the mill’s secondary leach circuit in support of safely processing high grade ore directly from the Cigar Lake mine. In particular, inter-stage pumps were introduced for slurry transfer between the secondary leach tanks, replacing the original pressure feed forward operation. The design and selection process for these pumps was strongly influenced by the uncertainty related to actual radiation dose exposure when processing undiluted high grade ore (up to 30%U), and consequently the desire to maintain minimal occupancy in the vault enclosure containing the secondary leach tanks. These constraints resulted in the decision to install positive displacement pumps above the leach tanks in a suction-lift configuration. Operating experience with this design has shown that the pump capacity is significantly de-rated due to process solution gas-entrainment and pipe scale build-up, particularly in the front end of the secondary leach circuit where reagent dosage is high. Experience processing high grade ore also provided accurate radiation dose data to demonstrate that the level of occupancy in the leaching vault enclosure could be re-evaluated to accommodate alternate pump configurations. This paper reviews the lessons learned and improvements made to safely increase the capacity and reliability of the leach inter-stage pump system.

Jan 1, 2020

By Balmer Neilly

To one with so little experience in matters pertaining to currency, international finance, and foreign trade, this is surely an ambitions venture on my part. However, this is a subject of prime importance to all seriously minded Canadians and, if we are to obtain any clear understanding of the factors involved, we must study the facts and debate such points as may remain at issue. During the last few years, the world' s better known economists have described the gold standard in all its ramifications and in such detail as to leave many of us even more confused than before. If we, then, are to acquire any real conception of its meaning and use, I think we must reduce it to its fundamentals and start from there. To my way of thinking, gold in ? trade and commerce is the symbol of honesty. When you seek to discharge a debt by tendering paper you hand the recipient an I.O.U. which may or may not be good, for the purchase of goods or services to the extent of its face value. When, however, you discharge a debt by the payment of gold, it constitutes a complete and final discharge. There are no reservations - no ifs and ands - and the transaction is definitely closed to the satisfaction of all concerned. Gold, then, is evidence of accumulated and transferable wealth that is immediately acceptable in practically every part of the world. However, there is not nearly enough gold to meet the demands of world trade, and. many years ago this deficiency gave rise to what we now describe as our banking system.

Jan 1, 1949

By S. Kapusniak

Specialist Machine Developments (SMD) is a design and manufacturing company involved in the design of Remotely Operated Vehicles (ROV?s), ploughs, trenchers and mining machines for use in submerged environments. Established in 1971, the company has made over 500 vehicles for subsea use. These range in size from small remotely operated swimming vehicles with a weight of less than a tonne to heavy duty seabed crawling machines with a weight of up to 310 tonnes (in air). Primarily, these machines have been designed for offshore vessel-based applications, but the machines are equally suited to other submerged mining applications onshore. Many onshore deposits can technically and theoretically be mined using currently available submerged mining ROV technology. Similar equipment to that in use subsea could easily be fast-tracked into use to extend the life of opencast mines facing severe hydrological problems. It could also easily be used to mine vertical ore-bodies where the stripping ratio has become uneconomical due to increasing depth. In some cases mining ROVs could even be suitable for use as the primary extraction method for a new mine. Exploration and extraction techniques used in oil and gas gradually developed and moved from land to offshore in the middle of the last century. Are we about to witness a similar shift with other minerals? This paper describes the design concepts of submerged mining equipment, targetted subsea mineral deposits, the suitability of submerged mining ROVs for onshore deposits, limits to their application and parallel research and development activities which will help to accelerate the use of such equipment in the emerging submerged mining sector.

Aug 1, 2013

By J. Wickens

"Campbell Mine is dedicated to quality management in the form of a Continuous Improvement (CI) Operating Philosophy. This paper discusses that philosophy, why and how it is being implemented in the milling facility, and some of the challenges experienced to date. Examples of mill CI team projects and results are described. This paper describes practical experiences for those who are considering or are in the process of adopting a CI operating Philosophy.INTRODUCTIONCampbell Mine is 100% owned and operated by Placer Dome Canada Ltd. The mine is located in Balmertown, Ontario approximately 300 km northeast of Winnipeg, Manitoba. Campbell Mine has produced over s,000,000 ounces of gold since commencing operation in 1949. The operation is profitable and continues to be a major contributor to the gold production of Placer Dome Inc.At Campbell Mine, the concept of Continuous Improvement (CI) is being implemented to make further improvements to safety, quality, productivity, and subsequently profits. CI is not a ""program"". It is a way of doing business that concentrates on improving the system rather than finding fault and being resigned to the status quo.CI focuses on involving all employees in the decision making process and tapping their expertise to improve every facet of the business. In the past, many solutions were simple ""band-aid"" fixes treating the symptom, only to see the problem resurface again. With CI, solutions endeavour to address the root cause of problems and eliminate them permanently. Another primary goal is to eliminate unilateral decisions that benefit a small group but have a negative effect on the whole system."

Jan 1, 1995

By Robert B. Parsons

"Recent amendments to the so-called ""flow-through share"" rules in our income tax legislation have given a new lease on life to this once popular investment vehicle.The original ""Dome funds"" for exploration in the Beaufort sea recognized the usefulness of flow-through share arrangements, but, by and large, flow-through shares have until recently not been able to compete effectively with other tax shelter instruments-mainly , limited partnership interests.This month, Tax Notes examines the new tax rules for investing in flow-through shares.IntroductionRecent income tax amendments have helped to rekindle investor and industry interest in so-called ""flow-through shares"" as a mechanism for mobilizing funds toward mineral exploration and development activities. In competing for investment funds, flow-through shares have historically placed a distant second in terms of investor popularity, being unable to compete with the more attractive features of limited partnership arrangements. However, primarily as a result of favourable changes to the income tax law, flow-through shares may be well poised for a comeback.This article examines the income tax considerations pertaining to issuing and investing in flow-through shares, and compares the former and the new income tax rules relating thereto. Of course, inasmuch as a flow-through share issue can involve various contractual arrangements between the investor and the issuer, there is a wide range of legal and business factors that generally have to be taken into account. A discussion of these matter s is beyond the scope of this paper, which is restricted to a summary of the special income tax factors attributable to flow-through shares."

Jan 1, 1983

By Julian V. Simela

Conventional methods of underground surveying use theodolites/total stations and 3D laser scanners to obtain information about the underground environment. Current methods of geo-referencing these instruments to a mine reference system include triangulation, trilateration and resection. However, despite technological advancements, surveying procedures have remained slow, laborious and relatively unchanged during the last half-century. Recent innovations in the robotics community have shown that automated mapping of underground mining tunnels can be undertaken using 2D/3D laser scanners. These techniques have the potential to, in turn, improve upon current underground surveying and mapping methods. Automating surveying and mapping using current surveying tools without changing the setting up procedures or removing current constraints, or even changing the type of equipment used, does not change the status quo. The problem of moving from a static, tripod based surveying and mapping system to an unconstrained mobile surveying and mapping system is the subject of this paper. A current challenge for automated mapping is the ability to automatically geo-reference a mobile mapping system to a mine reference system. For a mobile mapping system that uses a horizontally mounted 2D laser scanner to gather data of the underground environment, the challenge of determining its position and orientation within the mine environment is magnified even more. This paper introduces Mobile Automated Scanner Triangulateration (MAST), a technique under development at Queen?s that is designed to geo-reference a mobile mapping system to a mine reference system for the purposes of underground mine surveying. MAST quickly and automatically determines scanner 2D position and orientation (azimuth) in a mine reference frame by using minimal human input.

Aug 1, 2013

By W. M. Lupton

"Internal grinding mill entries are routinely done by mill personnel during scheduled maintenance periods. Reasons for entry include mill liner life profiles, liner inspcections and replacement and grinding media investigations. These entries require employees to adhere to safety regulations and policies including special permitting, testing, procedure-following practices and the wearing of proper personal protective equipment.A realized semi-autogenous mill entry safety hazard is the unpredicted breakage and occasional shattering of large diameter grinding media while personnel are inside. This was a concern to both media user and supflier. American Barrick's Holt McDermott Mine has improved mi l operational procedures and the media manufacturer has assisted by their developments to essentially eliminate this problem.This paper presents the improvements instituted; and the author's wish to communicate this potential hazard to other large diameter SAG ball users or potential users.INTRODUCTIONAmerican Barrick' s Holt McDermott mine is situated on Highway 101, some 70 kilometers northeast of Kirkland Lake, Ontario, 120 km east of Timmins and 90 km northwest of Rouyn Noranda, Quebec. The mine draws 160 employees from these surrounding areas to extract and process the underground ore, and recover near 60,000 ounces of gold per year. The mill department is completing it's fifth year of operation this spring.The company and the employees are proud of the safety improvements realized over the short history of the mine. Post accident/incident reviews and pro-active safety awareness programs have substantially reduced the mine's accident frequency and severity to date.One of the mill department's objectives is to provide a safe working environment for mill personnel, which includes the interior of the grinding mills."

Jan 1, 1993

By J. Bigu, M. G. Grenier

"Dust size distribution and aerosol size distribution measurements have been carried out in several Canadian underground uranium mines. In addition, dust samples have been analyzed for long-lived radioactive products of the U-238 and Th-232 natural decay chains using ex-spectroscopy and -y-spectroscopy techniques.From the data collected one may summarize: (a) most airborne particulates are of size below I u-m and 50% by mass are found above 1 u-m; (b) dust clouds are bimodal; (c) preferential deposition of radon (thoron) daughters takes place on airborne particulates in the sub -micron range at about 0.1 u-m; (d) deposition of radon (thoron) daughters is proportional to particle surface area; and (e) ex-spectroscopy and -y-spectroscopy of dust samples reveals the presence of U-238, Ra-226 and some of their short-lived and long-lived decay products.IntroductionExtended inhalation of airborne radioisotopes poses a potential health problem to occupational workers. Because of this, monitoring of radiation and dust levels for dose exposure calculation purposes is not only recommended but in most cases mandatory.CANMET (Energy, Mines a nd Resources Canada) has long since been engaged in a comprehensive monitoring program aimed at determining dust concentrations in the respirable size range, aerosol concentration in the sub-micron range, and in the radioactivity associated with these particulates in underground uranium mines. Measurements have been carried-out with gravimetric dust samplers, dust size selectors (including a horizontal elutriator , a fineparticle spectrometer and Nuclepore* filters of different pore sizes) and a condensation nucleus counter(1 – 6). Inactive and active working sites have been monitored according to some typical mining operations. A summary of these data has been given elsewhere(3- 5)."

Jan 1, 1984

By R. Tomás, J. B. Serón, M. Romana

The Slope Mass Rating (SMR; Romana, 1985) geomechanics classification was developed as a sequel of Bieniawski’s Rock Mass Rating (RMR) system, which was almost impossible to use in slopes due to the extreme range of the correction factors (up to 60 points of a maximum of 100) and to the lack of definition of them. A detailed quantitative definition of the correction factors is one of the advantages of SMR classification. During the last thirty years the use of SMR system has been extended to many countries from the five continents and, thus, it is time to review the most interesting developments. Both RMR and SMR are discrete classifications, depending on the values adopted by the variables that control the parameters. This can cause major changes in the parameters value due to small differences in the variables value, with changes in the final rock mass assigned quality. On the other hand, geomechanics quality indexes are extremely biased. To avoid this problem, some authors have proposed continuous functions for SMR. This classification has been also adapted for its application in heterogeneous and anisotropic rock masses, for high slopes, for is application trough stereographic projection and Geographical Information Systems, has been used as susceptibility rockfall parameters and has been included in the technical regulations of several countries. Additionally, some open access computer tools have been developed for the computation of SMR. Consequently, this paper reviews: 1) the most important modifications and adaptations of slope classifications which derive directly from SMR; 2) the use of SMR throughout the world; 3) many significant papers on slopes analysed with SMR all over the world; and 4) future trends in the use of SMR.

Jan 1, 2015