Search Documents

By E. Ghali, W. Zhang, M. Robichaud, G. Houlachi

"The performances of six mesh and one plate dimensionally stable anodes have been investigated in the zinc electrolyte at 38oC and compared to conventional silver-lead alloy anodes. The electrochemical behaviour of these anodes was studied by cyclic voltammetry, galvanostatic, potentiodynamic, open circuit potential and electrochemical noise measurements. It was observed that at the end of 24 h of galvanostatic polarization at a current density of 50 mA/cm2 in the zinc electrolyte at 38oC, the mesh V had the lowest potential followed by mesh III, mesh VI, plate-V, mesh IV, mesh I, and mesh II electrode. When the potentials for mesh I, mesh III, mesh IV, VI and plate-V, mesh V were compared with that of the Pb-0.7%Ag anode (1920 mV/SHE), they were found to be 6%, 16%, 7% 10%, 17% lower, respectively.After 16 h decay following the 24 h polarization, the mesh III had the lowest corrosion rate (51 mS/cm2) among the seven specimens, followed by the plate-V, mesh V, VI, IV, I and II (221 mS/cm2). For the fresh surface as received, after two hour open circuit potential measurements, mesh I had the most positive (noble) potential (1382 mV/SHE) among the seven electrodes followed by the plate-V electrode, mesh V, mesh IV, mesh VI, mesh III and mesh II (751 mV/SHE). After consecutive series of electrochemical testing, mesh V, mesh III, mesh VI had lower corrosion rates (~ 343± 6 µA/cm2) than that of mesh IV, mesh I, plate-V, and mesh II (~ 644± 143 µA/cm2).INTRODUCTIONThe continued use of lead based anodes in the electrowinning process has been mainly due to their relatively low cost as compared to other materials (Msindo, Sibanda, & Potgieter, 2010). They have good electrical conductivity, stability during electrolysis, very good corrosion and wear resistance (Ivanov, Stefanov, Noncheva, Petrova, Dobrev, Mirkova, Vermeersch, & Damaerel, 2010). However, lead-based anodes give their high energy consumption and low corrosion resistance for electrowinning. To overcome these problems, Dimensionally Stable Anodes (DSAs) has been chosen (Msindo et al., 2010). Comparing to the traditional lead anodes, the DSA anodes have many advantages: (1) no contamination; (2) no loss of anode material, pure electrolyte; (3) lower gas bubble effect through special anode designs; (4) use of higher current densities (Msindo et al., 2010). The success of DSA anodes has been attributed to their chemical stability that allows them to maintain nearly constant dimensions during the life of the anode even when operating in environment with low pH values. Due to their stability, the consumption rates of DSA are as low as 1 mg/amp.y (Alfantazi & Moskalyk, 2003)."

Jan 1, 2016

By A. Monballiu, J. A. Martens, Y. W. Chiang, A. Van Audenaerde, R. M. Santos, T. Van Gerven, B. Meesschaert

In this work, bioleaching of non-sulphidic materials by applying chemoheterotrophic bacteria and fungi is studied. It was found that the tested fungus, Aspergillus niger, leached substantially more nickel from olivine than the tested bacterium, Bacillus mucilaginosus. A. niger also outperformed fungal species Humicola grisae and Penicillium chrysogenum in the leaching of olivine. Contrary to traditional acid leaching, the microorganisms leached nickel preferentially over magnesium and iron. On average, a selectivity factor of 2.2 was achieved for nickel compared to iron. This can potentially facilitate postprocessing of the leach liquor and reduce the cost. The impact of ultrasonic conditioning on bioleaching was also tested, and substantial increase in nickel extraction with A. niger was observed. This was credited to an increase in the fungal growth rate, the promotion of particle degradation, and the detachment of the stagnant biofilm around the particles. Furthermore, ultrasonic conditioning enhanced the selectivity of A. niger for nickel, resulting in a selectivity ratio for Ni/Fe equal to 3.5. The chemical resistance of the selected microorganisms to several heavy metal and metalloid (As(III,V), Cd, Cr(III,V), Ni, Pb, Zn) was evaluated. It was found that, with the exception of As(v) and Cd, A. niger has high tolerance to these components. Therefore, this biohydrometallurgical route can potentially be applied to non-sulphidic wastederived materials, such as industrial slags, ashes and sludges.

Jan 1, 2014

By R. H. Duval

"In May 1936, Pamour started producing gold by cyanidation of flotation concentrates, and in 1939 was milling about 1, 600 tons per day.Refining records dating from 1939 show two oil-fired furnaces in use, (Rockwell type 46 11 x 29 11 inside oval shell).Refining time averaged 7. 83 hours during the year 1939, indicating a complete refining shift of about 9. 33 hours. That year appears to be characteristic of the period with regard to time required and results obtained.For that year total fineness (gold + silver) of the bars averaged 940 (approx.), but it frequently dropped below this figure, sometimes far below.Furnace lining life varied widely from three to seven or more months. Sillimanite was the standard lining but Mullfrax 41 was frequently used.For many years refining practice remained practically unchanged, and in 1960 procedure still consisted essentially of mixing a flux(% Composition Borax 41, Silica 11, Soda-Ash 11, Nitre 15, Mn02 22) with cyanidation precipitate in the ratio of l. 2 to l and heating to a medium heat (yellowishred, 2000° F) with a low flame for a long time. Time required was about 10. 5 hours per refining. Results were still much as detailed above.At this time it was decided to revise refining procedure, in an effort to shorten refining time and obtain consistently good bullion fineness."

Jan 1, 1965

By L. I. Kiss, S. Perron, D. Toulouse, S. Poncsák, A. Perron

Bubbles play an important role in many industrial processes. In a Hall-Heroult cell, used for aluminum production, bubbles contribute to induce flow in the cell. The induced flow is important for the thermal balance of the cell as well as for the distribution and dissolution of the alumina. The existence of the bubble layer does not have advantages only. It increases the voltage of the cell and causes deformation along the cryolite-molten aluminum interface. The role of the anode inclination in the behaviour of the bubble layer as well as in the hydrodynamics of the bath is not clearly understood. In this work, the effect of the anode inclination angle on the bubble driven flow is studied in an industrial scale air-water model. The inclination angle is varied up to 5° from the horizontal. The instantaneous flow field is captured by Particle Image Velocimetry (PIV) system. The mean velocity fields were calculated by ensembleaveraging the instantaneous velocity fields measured at different time. The existence of the counter-flow in the interpolar space and the vortex in the side channel has been confirmed. Furthermore it has been observed that the effect of anode slope on the velocity field is weak.

Jan 1, 2006

By K. Niboucha, M. Zergoug, S. Brick-Chaouch, H. Houali

"Corrosion is an electrochemical process that causes degradation and deterioration of various steel works (pipelines, drains, cisterns) whether they are buried, immersed, or not. Worldwide, we estimate that corrosion destroys a quarter of the annual production of steel at a rate of 5 tons per second. Several techniques are used to protect against corrosion. Among these processes, Cathodic protection, which is regarded as the best technique to assure the protection of steel, works against this phenomenon. This is achieved either by a system of reactive anodes, or by the technique of impressed current protection or other techniques. Before any installation of cathodic protection, a preliminary study and pre-evaluation of certain parameters must be made. In the present work, we will present an example of dimensioning of an installation of cathodic protection by imposed current of a pipeline using solar energy, where we discuss the following items:•,Evolutions of the potential as well as current along the pipeline and their respective expressions deduced from the laws known as telegraphists;•,Range of protection (potential of protection along the pipeline);•,Influence of the isolation resistance of the coating on the range of protection;•,Effect of the aging of the coating and its influence on the current of protection."

Jan 1, 2005

By A. Singh

Two alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho have been processed by direct extrusion at 300°C and 200/230°C to produce various microstructures containing icosahedral quasicrystalline phase with different grain sizes. The alloys were mechanically tested in tension and compression. The mechanical properties were related to the grain size and microstructures studied by transmission electron microscopy. The extruded alloys showed a mixture of nano-sized icosahedral and monoclinic Mg4Zn7 phase, as well as icosahedral phase particles a few hundred nanometers in size distributed in the matrix. Coarse icosahedral phase particles several micron in size also remained after extrusion. The alloys Mg96.9Zn2.7Ho0.4 and Mg93Zn6Ho extruded at the same temperature of 300°C produced very different grain sizes of 15 and 3 µm, respectively. The alloy Mg96.9Zn2.7Ho0.4 extruded at 200°C and Mg93Zn6Ho extruded at 230°C produced grain sizes of 0.7 µm and 1.5 µm, respectively. Both the alloys showed yield stresses of about 300 MPa in both tension and compression with elongations of about 18%. Hall-Petch parameters are calculated for the alloys.

Jan 1, 2006

By H. Houali

Corrosion is an electrochemical process that causes degradation and deterioration of various steel works (pipelines, drains, cisterns) whether they are buried, immersed, or not. Worldwide, we estimate that corrosion destroys a quarter of the annual production of steel at a rate of 5 tons per second. Several techniques are used to protect against corrosion. Among these processes, Cathodic protection, which is regarded as the best technique to assure the protection of steel, works against this phenomenon. This is achieved either by a system of reactive anodes, or by the technique of impressed current protection or other techniques. Before any installation of cathodic protection, a preliminary study and pre-evaluation of certain parameters must be made. In the present work, we will present an example of dimensioning of an installation of cathodic protection by imposed current of a pipeline using solar energy, where we discuss the following items: ? Evolutions of the potential as well as current along the pipeline and their respective expressions deduced from the laws known as telegraphists; ? Range of protection (potential of protection along the pipeline); ? Influence of the isolation resistance of the coating on the range of protection; Effect of the aging of the coating and its influence on the current of protection

Jan 1, 2005

By F. Lambert

"Amok Ltd./Cluff Mining operates a uranium mine at Cluff Lake in northern Saskatchewan. The project consists of one open pit and one underground mining operation along with a full-scale milling installation.The underground stoping operations are of the narrow vein type and are done between two levels 50 m apart. The mining method is undercut with concrete backfilling. Cuts are 3.5 m in height and can be as narrow as 1.4 m in width.Stoping operations are mechanized utilizing a CT-500E electric Microscoop marketed in Canada by Teledyne. The machine is only 85 cm in width and does all the mucking in stopes. Ore passes are provided in stope roughly every 40 m to 50 m.This paper describes the utilization of the CT-500E Microscoop in the company's underground operations and provides performance data related to the experience.IntroductionThe Amok Ltd ./Cluff Mining operation is located in the northwestern corner of Saskatchewan. The project started in 1980 with open pit mining and milling operations. In 1983, an underground mining operation began production . Today, the Amok Ltd./Cluff Mining installation produces 800 tonnes of uranium per year , which originates from both the open pit and the underground mine at about the same proportion."

Jan 1, 1990

By Diego L. Romero, Joy P. Romero

"IntroductionThe purpose of this paper is to explain the theory and demonstrate the industrial applications of electrostatic separation. Wabush Mines' use of this type of processing for the concentration of iron ore is unique in the industry. Other minerals are concentrated electrostatically but the process is not widely used.Typical minerals separated by electrostatic separation techniques are:Non-ConductorsAnhydriteApatiteBariteBastnasiteBerylCalciteChrysotileCorundumDiamondEpidoteFeldsparsFluoriteGarnetGypsumHornblendeKyaniteAcmiteAugiteBrookiteCassiteriteChalcopyriteChromiteColumbiteCopperDaviditeEuxeniteFerberiteFrankliniteGalenaGoldGraphiteHematiteMica (Biotite)Mica (Muscovite)MonaziteOlivinePerovskiteQuartzScheeliteSideriteSillimaniteSpheneStauroliteSulphurTopazTourmalineXenotimeZirconConductorsIlmeniteIlmenite-( High Iron)IlvaiteKoppiteMagnetiteMarmatiteMolybdenitePyriteRutileSamarskiteSphaleriteTantaliteWolframiteWulfeniteThe limitations of this process are:1. There must be a difference in conductivity between the minerals being separated.2. The size range must not be very wide.3. The specific gravity of minerals being separated should be similar or the minerals to be pinned should be lighter. 4. The feed must be dry.5. The particle shape should be more or less uniform. 6. The feed must not be high in true middling particles."

Jan 1, 1989

By J. E. Lee

"This paper describes the current practices and experiences, and discusses design parameters concerning slurry pumping at Inco Metals Company in the Sudbury District. It deals mainly with the long tailing and concentrate lines. Subject matter is arranged under the following headings: pumps, lines, instrumentation, system design, operation.IntroductionThe Inco Metals Company is the mining and processing section of INCO LIMITED. In the Ontario Division, it operates 13 mines, 5 mills, a smelter, an iron ore plant and 3 refineries, all engaged in the mining and recovery of nickel and copper. This paper describes the slurry pumping practices in the mills of the Ontario Division.The PumpsWe have in our Sudbury area mills most of the available types of slurry pumps, in sizes from one inch up to twelve inches, a total of about 400 pumps. The rubber-lined, horizontal shaft pump is; most numerous. However, for certain applications, the hard-metal pump is essential, and is becoming more popular for general mill service. Two types of vertical shaft pumps are used. There are a few diaphragm pumps on small thickeners, but the larger thickeners have centrifugal pumps either directly connected to the under-flow or with one pump handling several gravity underflows. We have not used piston or plunger pumps in our mills."

Jan 1, 1978

By A. J. DeArdo

Linepipe steels have come a long way in the past forty years. In fact, modern, high strength steels for large diameter linepipe applications represent one of the seminal accomplishments in metallurgy of the past half-century. The synergy of advanced steelmaking, alloy design including microalloying, hot rolling, and interrupted accelerated cooling has led to the marvelous steels being used today. The drive for higher performance pipelines has been motivated by the energy sector of our global economy who wanted both higher throughput capacity, i.e., larger diameters and higher pressures, and lower material cost, i.e., relatively thinner gauge wall thicknesses. These requirements led to new steels with higher strengths, better toughness and improved weldability. The goal of this paper is to trace the evolution of linepipe steels from the X60 grades of the small diameter pipelines of the 1960s to the (X80 - X120) grades used in the large diameter pipelines of today. The metallurgical triumphs permitting this success story, e.g., clean steel practices, controlled rolling, microalloying with Nb, and using IAC to obtain low temperature transformation products, will be highlighted and discussed.

Jan 1, 2005

By Bradford P. Simser

The theoretical capacity of various ground support components can be misleading, especially in bursting ground where the failure mode is often in the retainment system. Wire mesh screen seams often peel open rather than breaking the wire strands, fractured rock often un-ravels around the bolts rather than breaking the bars. If a weak link(s) in the system fails prematurely, then the potential capacity of the system may never be fully realized. Underground observations are used to show how some support systems behave in the field. Various combinations of wire mesh screen with friction bolts, rebar, modified conebolts, cablebolts, shotcrete and mechanical rockbolts are considered. A short case history is used to contrast the performance of ?just-intime? development in a high stress faulted area versus a tunnel subjected to multiple stress changes in a similar environment. The latter proved to be a serious ground support problem when the well developed fracture zone around the opening was subjected to dynamic loading from a large seismic event causing a severe rockburst. In such cases an improved mining strategy may be more relevant than higher capacity support systems.

Feb 1, 2008

By Jeonghwan Kim

Intelligent Excavation System (IES) has been considered to be one of the desirable solutions to improve the productivity, quality and safety of the current earthwork processes. IES is composed of various hardware and software modules including task planner (work command generator), local and global work environment sensors, GPS and other sensors to acquire the excavator?s status, robotic controller and electronic valves, and the manipulator (excavator). A data communication manager was required to coordinate the signal or data-flow in between these modules considering the operational status of IES such as; excavation start/completion, truck detection, terrain model update, emergency stop, local sensing, GPS/motion sensor data handling, and so on. This paper presents the role and functions of this data communication manager. After every possible operational status of IES operation was identified, a protocol of each communication process in the form of string-type was made. The components of IES are connected with either wired or wireless network. Therefore, they can communicate with the manager using socket (TCP/IP) communication. The data communication manager is also capable of accessing a web-based project management information system, which constantly updates the performance of excavation robot to online database.

Aug 1, 2013

By G. J. Hamilton

"THE Royalite-Canada Southern Coleville No. 1 gas strike of August 15th, 1951, and the closely following low gravity black-oil strike of August 23rd, were the first of a series of recent oil and gas discoveries in western Saskatchewan. They are in what is now known as the Coleville field, 25 miles north and west of Kindersley and 30 miles east of the Alberta-Saskatchewan border (Figure 1).Gas flows have been recorded in the Viking sand at daily rates of between 5 and 10 million cubic feet, and black oil of 15° A.P.I. gravity is produced from Mississippian sediments of Banff age at a daily rate .of 50 to 100 barrels on pump.Development drilling was carried on during the winter months, with very little attempt at step-out exploratory ventures. This year, however, a step-out programme to the northeast (Figure 2) is •being carried on in order to determine the position of a possible truncation of Mississippian sediments in that direction. Section 30 of the Coleville area has been fully developed on a 20-acre wellsite basis, and structural information is restricted to local rather than regional interpretation. No attempt will be made in this paper to interpret the Coleville area with respect to the regional geology in any but a general manner."

Jan 1, 1952

"ChairmanThis part of the discussion is intended as an exchange of information between those who have installed rubber liners in their mills and a means of others to get information that may help them decide if rubber liners would be applicable to their mills.To start the discussion and to relate it to the previous section of this symposium Mine Equipment Co. Ltd. have supplied some graphs that will give some idea of the noise suppression that may be expected from the u.se of rubber liners instead of steel. The figures used in preparing the graphs came from installations of rubber liners in Sweden.L. Strah - Mine Equipment Co.The graph, Figure 1, shows on the bottom the octave band range. The noise level generated by the steel liners is represented by the dotted line and lies within the shaded area where it is considered that hearing damage may result. The solid line represents the noise level generated by rubber liners in the same mill and you will see it is below the shaded area. Although it is not marked on the graph I think the decibel range is from 7 5 to 115. The next one, Figure 2 which shows the relative noise levels generated by steel balls and pebbles with both steel and rubber liners shows the decibel range."

Jan 1, 1968

By R. Maxwell

"At Opemiska Copper Mines we have, over the past four years, operated 300 cu. ft. and 700 cu. ft. flotation cells as roughers, scavengers and cleaners and found them competitive with conventional flotation cells on a cu. ft. basis on all phases of flotation.The economics are very much in favour of the large cells for the following reasons:Power consumption is 35 to 40%, of conventional machinesMaintenance cost is about 20 to 25% of conventional machinesSpace required is about 30 to 35% of conventional machinesInstallect cost is about 40%, of conventional machinesTo put the above in more concrete terms below is what we are doing at Opemiska:1. Increasing mill capacity from 2000 to 3000 T.P.D. and will use only 5Cff, of the flotation space for 3000 tons that we used for 2000 T.P.D. with conventional flotation machines.2. Will require only 10 flotation cells for 3000 tons against 85 conventional cells for 2000 tons.3. Cells will be, one 2000 cu. ft. rougher, six 700 cu. ft. scavengers (2 banks of 3 each) and one cleaning circuit using three 300 cu. ft. cells.You will note that in this 3000 ton per day plant, we are going to have only ten cells. Had we put in conventional cells for this tonnage, we would have needed 120 cells."

Jan 1, 1970

By J. O. Marsden

Over the past eight years, Phelps Dodge (a division of Freeport-McMoRan Copper and Gold, Inc.) has developed a suite of proprietary hydrometallurgical processes for the treatment of copper concentrates as an alternative to conventional smelting and refining technology. The technical viability of two processes has been commercially demonstrated in a large scale plant at Bagdad, Arizona, designed to process approximately 52,500 metric tons per year of concentrate containing 30.5% copper. The first process utilizes high temperature (225°C) pressure leaching, followed by countercurrent solid-liquid separation, and then blending of the copper-bearing solution with low grade stockpile leach solution for subsequent treatment by SXlEW for copper recovery. The second process uses super-fine grinding, medium temperature (l60°C) pressure leaching, followed by solid-liquid separation, and treatment of high grade copper-bearing solution by direct electrowinning to recover the bulk of the copper values. The latter process will be utilized at Morenci in a commercial facility designed to treat mixed chalcopyrite-chalcocite-covellite concentrates. This facility is scheduled to start up in 2007. Other flowsheet options have been developed by Phelps Dodge for application to a variety of concentrate materials in specific situations. Examples of various flow sheet options are presented in this paper, and the advantages and disadvantages associated with each are discussed in detail.

Jan 1, 2007

By David Lewin

The journey toward cleaner coal-fired power generation is driven by technological improvements, more stringent regulations around greenhouse gas and other air emissions, and the potential of one of Canada?s most abundant resources. Within this context, EPCOR is leading efforts to commercialize gasification technology to produce electricity with near-zero emissions. By turning coal, oxygen, and water into synthesis gas through a gasification process ? and then capturing CO2 ? it is possible to dramatically reduce greenhouse gas and smog-related emissions. EPCOR is conducting front-end engineering and design work on an Integrated Gasification Combined Cycle technology (IGCC) utility-scale plant ? in conjunction with the Canadian Clean Power Coalition ? at its Genesee site, west of Edmonton. EPCOR, the Alberta Energy Research Institute, and Natural Resources Canada have each contributed $11 million to the $33 million project. A critical element of the project features the capture of CO2, which would be piped underground for long-term sequestration, or for use in enhanced oil recovery (EOR). The combination of IGCC and CO2 sequestration, at this scale, has not been used anywhere else in the world.

May 1, 2008

By R. U. Seneviratne, B. K. Ahlgren

In this paper we follow various technological discoveries and developments in the purification of minerals and metals in the mining industry by ion exchange. For approximately 100 years, ion exchange has been a known and variously applied purification and separation technology used by scientists and producers. It would seem obvious that the producer’s objectives have always been to achieve the highest quality products and the lowest operation costs, but also with the least amount of technological complexity. As a strategy to reach these goals, much effort has been expended in the quest to improve continuous ion exchange (CIX) systems by reducing utility needs and resin degradation or loss while at the same time improving productivity and reliability. Recent developments from a number of companies have pushed equipment boundaries, resulting in a variety of unique commercial equipment designs each with a varying degree of success. The challenge set forth for all new designs has been a truly continuous process with no sacrifice in the afore mentioned benefits. One very recent equipment design based on system symmetry appears to meet many of these objectives with greater flexibility and less complexity resulting in better economics for the producer.

Jan 1, 2014

By Frands Jensen, Erik Eriksson

"Haldor Topsoe’s Wet gas Sulfuric Acid (WSA) technology has been proven in a number of industries converting sulfurous gasses to concentrated sulfuric acid. In the metallurgical sector plants have been delivered handling SO2 gasses from copper, zinc, molybdenum, and lead ore. WSA has high energy efficiency and allows autothermal operation from feed gas strengths as low as 3.0% (volume). Recent variants of the WSA process have been developed that allow very high SO2 conversion efficiencies of over 99.9%. This paper describes the technology, its advantages and industrial achievements.The WSA technology is well suited for production of concentrated sulfuric acid of commercial quality from the sulfur dioxide (SO2) gas that inevitably emerges from the metallurgical processes. Some of the features that make the WSA technology attractive for this application are:- High SO2 conversion rates (up to 99.99%)- High energy efficiency leading to a low autothermal point (~ 3% SO2)- No need for gas cooling and drying to produce concentrated sulfuric acid- No production of waste- Very low cooling water consumptionThis paper describes the WSA process principles and highlights features that make this process attractive for handling SO2 gases."

Jan 1, 2014