Search Documents

By H. C. Cooke

"This paper has reference in a general way to the region extending from the north shore of lake Buron to the northern limit of the elliptical-shaped area generally known as the Sudbury Basin, and more especially to the district lying south of the Basin (Fig. 3). Attention is concentrated mainly on the structure of the district and, as space does not permit of much geological description, it is assumed that the reader has some knowledge of the general geology. The accompanying table outlines the sequence of the rock formations according to the most recent available information; for further details the interested reader may consult the publications of the various authors mentioned in the paper.STRUCTURE OF THE SEDIMENTARY ROCKS SOUTH OF THE SUDBURY IRRUPTIVEThe rocks south of the Sudbury irruptive, excluding certain intrusives, are, in order from north to south:(1) A band of basic lavas.(2) A band of well-bedded greywackes and quartzites, long termed the McKim greywacke.(3) The Copper Cliff formation, with McKim greywacke' both to the north and south.(4) The Ramsay Lake conglomerate.(5) A thick quartzite formation.All these rocks strike approximately east-northeast, dip steeply south, and generally face south, though there are local exceptions."

Jan 1, 1954

By T. ?kre, O. M. Dotterud, S. Haarberg, J. Thonstad, G. M. Haarberg

An electrowinning pilot plant has been constructed at Falconbridge Nikkelverk A/S, Kristiansand, Norway. The equipment consists of a mixing tank where the electrolyte composition and temperature are controlled, an electrowinning tank equipped with five cathodes and six anodes of commercial size and design and a dechlorination facility. Electrowinning experiments were carried out in this pilot plant using acid cobalt chloride solution from the cobalt tankhouse. Key parameters were varied to obtain an improved understanding of the cobalt electrowinning process, focusing on the detrimental deposition of cobalt oxide on dimensionally stable anodes. The extent of anode scaling was found to be dependent on the electrowinning conditions. Low pH, temperature and cobalt concentration resulted in less scale being formed, however at the expense of cobalt current efficiency and cell voltage, adversely affecting electrowinning production capacity and energy consumption. When operating at high acidity, pH in the anolyte was higher than in the catholyte, which is believed to be due to H+ ions taking part in the current transport across the diaphragm, migrating out of the bags surrounding each anode.

Jan 1, 2005

By Benoît Valley

Optimization of the mining sequence in terms of economics (maximizing net present value) often leads to multi-front mining methods generating pillars. Significant resources are tied up in these pillars, but mining them is often challenging. In order to improve our understanding of rock mass behaviour while extracting these pillars, an extensive monitoring program has been designed and implemented at Vale?s Coleman mine (Sudbury, Canada). The program focuses on existing and new technologies that have potential for monitoring deformation and rock mass property changes. It includes both active and passive methods: gravimeters, multi-point borehole extensometers, fiber optic strain meters, fixed and portable three-component seismic arrays, borehole imaging and sonic logging, and, repeated LiDAR surveys. This paper reports results from an initial project phase, when only a small amount of mining has taken place. The goal was to test and compare technologies in order to assess their sensitivity, accuracy, repeatability and suitability for underground mining conditions. Value is gained by having a broad range of monitoring devices running side by side, enabling comparisons and benchmarking.

Jun 1, 2012

By Bradford P. Simser

Increasingly sophisticated rock mechanic tools are becoming more and more available for today?s ground control specialist. However many problems are still beyond our ability to explicitly calculate or measure. There is often a gap between the ?art? and the ?science? of rock mechanics. This paper focuses more on the ?art?, giving relatively simple examples of underground observations and micro-seismic records to help explain ground control issues. Ground support techniques such as in cycle shotcrete with high pressure water scaling, mesh and bolting, pumpable resin bolts/cablebolting, and yielding bolts with load spreading straps are discussed. The use of primary/secondary type blasthole sequences in moderate to high stress situations is also discussed with several examples of the micro-seismic response to the stoping. Relatively erratic geology with high material strength contrasts is currently being mined with blasthole methods at Nickel Rim South. Although the mine is still in its? ?early? days, over 1 million tonnes has been extracted and some empirical experience is highlighted with potential longer term issues also being discussed.

Oct 1, 2010

By C. B. Webber

"Sherritt Gordon's experience with rubber mill liners began in 1964 at the Lynn Lake Farley Mine and continued at the Fox Mine in 1960, and the Ruttan Mine in 1973. This paper describes the history of the performance of rubber mill liners at the three mine operations.LYNN LAKE - FARLEY MINEThe Lynn Lake Farley Mine, which ceased production in 1976 due to exhausted ore reserves, was a 3500 T.P.D. copper-nickel operation; consisting of two parallel rod mills followed by three stages of ball mill grinding. A circuit modification in 1964 necessitated one of the tertiary ball mills to be used as a pyrrhotite regrind mill. This 8' x 5' Hardinge conical mill drawing 225 HP was initially installed with steel liners and lifters. After several months of operation a routine inspection revealed severe channeling and washing behind the liners which was threatening to erode the ball mill shell. It was thought that the highly acidic condition in the mill, due to grinding 100 º6 pyrrhotite, was accelerating the wear of the steel liners. At this time it was decided to reline the mill with rubber liners to see if the wear problem could be relieved, and in December 1964 a set of Skega rubber liners were installed."

Jan 1, 1981

By Li Qihou, Liu Zhihong, Liu Zhiyong, Yao Wei

Black copper sludge, which mainly contains copper, arsenic and a little antimony, bismuth, selenium, tellurium, is an important recyclable secondary resource. In this paper, selective removal of arsenic from black copper sludge by alkaline oxidative pressure leaching was studied. The influences of alkali concentration, leaching time, leaching temperature, oxygen pressure, liquid-solid ratio and other variables on the leaching rate of arsenic, copper and tellurium were investigated. The results were as follows: when the leaching process was conducted at initial alkali concentration of 1mol/L, liquid-solid ratio of 10, stirring rate of 500r/min, leaching temperature of 140°C for 5 h and oxygen pressure of 2.5MPa, the leaching rates of arsenic and tellurium were 85.43% and 59.7% respectively, and copper, antimony, bismuth were not leached. Hence, arsenic has been removed effectively from black copper sludge, while the valuable metals such as copper, antimony and bismuth remained in the residue that can be further recovered easily. INTRODUCTION Black copper sludge is a byproduct in the purification process of copper electrolyte. Arsenic, antimony and bismuth are major harmful impurities in copper electrolytic refining system. The accumulation of these impurities will cause adverse effects, such as the increase of electrolyte resistance and power consumption and deterioration of cathode copper quality (Wang, Liu, & Zhang, 2001). Hence, electrolyte purification is an essential part of the electrolysis process (Liang, Chen, & Guo, 2009). Electrolyte purification methods include electrowinning (Davenport, King, Schlesinger, & Biswas, 2002), solvent extraction (Navarro, Simpson, & Alguacil, 1999), ion exchange (Arroyo et al., 2017), coprecipitation (Wang et al., 2003, 2018; Xiao et al., 2007; Xiao, Cao, Mao, Shen, & Ren, 2014), activated carbon adsorption (Navarro & Alguacil, 2002), electrodialysis (Cifuentes et al., 2015), redox process (Zhou, Peng, Zheng, Ma, & Cui, 2011; Peng, Zheng, Zhou, & Chen, 2012; Zheng, Peng, Ke, & Chen, 2013), among which the electrowinning method is simple in operation and effective in impurities removal, making it the main process for current electrolyte purification. Some copper ions can react with harmful impurities to form complex black copper sludge by controlling the operation conditions of electrowinning process. Based on the estimated data provide by Davenport et al. (2002), an annual output of 400,000 tons cathode copper could produce 432-2168 tons of black copper sludge by electrowinning method. Black copper sludge contains 30~50% copper, 15~30% arsenic and a small amount of rare elements such as selenium and tellurium. Thus, recovery of valuable metals can bring huge economic interests. Moreover, arsenic in these sludges could cause significant environmental pollution. Therefore, effective removal of arsenic from these sludges is urgent and significant.

Jan 1, 2019

By W. A. Jones

THE Ross mine, a subsidiary operation of Hollinger Consolidated Gold Mines, Limited, is situated near the north end of lot 1, concession 2, Hislop township, Ontario. The property comprises the north half of lot 1, concession 2, and the south one-third of lot 1, concession 3. It is readily reached by a good motor road from the village of Ramore, 7.5 miles to the southeast on the Temiskaming and Northern Ontario railway. The-mine has been developed to a depth of 900 feet and the current daily production rate is about 260 tons. From the inception of operations in March, 1935, until December 31st, 1942, 455,720 tons of ore with a total value of $4,169,-316 have been milled. The silver to gold ratio of 1.48 to 1 is unusually high for Ontario gold mines. The deposit is interesting because the relationship between hydrothermal metamorphism and three successive stages of fracturing and mineralization is marked with considerable clarity. During the past seven years, detailed geological maps of the mine have been kept up to date, many thousands of feet of diamond-drill core have been logged, and numerous thin and polished ore sections have been studied. The present paper describes the structure and mineralogy of the orebodies.

Jan 1, 1944

By M. S. Hedley

"The Lucky Jim mine is at Zincton in Slocan mmmg division; on the Kaslo-Nakusp branch of the Canadian Pacific railway. It is owned and operated by Zincton Mines; Limited; a subsidiary of Sheep Creek Gold Mines; Limited. The mine is far in the lead in the production of zinc in the Slocan. Its recorded production from concentrates and shipping ore was 102; 260; 191 pounds of zinc to the end of 1945.GENERAL GEOLOGY With the exception of acidic dykes the rocks near the Lucky Jim mine belong to the Slocan series, which is Triassic in age and consists principally of argillaceous rocks. It disconformably overlies greenstones of the Triassic Kaslo series about 3 miles to the northeast, and is cut by granitic rocks of the Nelson batholith 5 miles to the southeast.The sedimentary rocks in this area are best referred to on the whole as slates. They lie within the more fissile basal part of the Slocan series. The term 'slate belt' conveniently distinguishes this area of rocks characterized by slaty cleavage from the more massive argillites that are more characteristic of the Slocan as a whole. The contact between the slaty and massive argillites lies ½ mile southwest of the mine."

Jan 1, 1954

By F. Doxey

Introduction In order to improve outputs and to reduce or hold mining costs, many attempts have been made to mechanize the getting and loading of coal in the major coal producing countries, and machines of various kinds and sizes have been designed and manufactured. Some of the most important are: Joy Continuous Miner Joy Coal Auger Goodman Mining Machine Lee-Norse Koal-Master Jeffrey Colmol Cardox Hordsecg Recovery Drill German Coal Plough British Coal Plough with agitated blades M. & C. Samson Stripper AB Meco-Moore Cutter Loader Joy Gloucester Getter The three last named are the chief longwall machines in use and the AB Meco-Moore and the Samson Stripper are doing a good job in their respective applications. It is understood that the Gloucester Getter recently installed in a British colliery also shows reasonable promise. It was felt, however, that to meet the conditions of the mines in Nova Scotia, any machine developed must have certain distinctive characteristics. It must: ( 1) Be able to cut and deliver coal in quantity and of the right sizes ( 2) Be easily manoeuvrable ( 3) Be suitable for longwall operations ( 4) Not interfere with timbers already set ( 5) Cut its own stable (6) Work on reasonably heavy gradients

Jan 1, 1951

By A. Dunnett, N. J. Turner, J. Koyanagi, M. Ji

The analysis of rare earth element (REE) samples is a necessary part of the metallurgical process for rare-earth bearing ores, providing invaluable information during testing procedures. This requires a fast, multi-element technique, capable of analyzing a variety of matrices for all rare earth elements. X-ray Fluorescence spectrometry and Instrumental Neutron Activation Analysis are typically used for high concentrations of REE, but they have limitations for some process work applications due to an inability to measure all elements, longer analysis times, significant interferences and elevated detection levels. The work reported here uses new approaches with Inductively Coupled Plasma Mass Spectrometry (ICP-MS) in order to achieve high precision and accuracy within acceptable timeframes. A combination of aerosol dilution and Kinetic Energy Discrimination (KED) produce a process solution assay method that is robust enough to deal with changing sample matrices and concentrations, whilst maintaining low reporting limits and precisions of less than 5% Relative Standard Deviation (RSD). For high concentration metallurgical and geological samples, a sodium peroxide fusion digestion procedure was used, followed by ICP-MS analysis using extended dynamic range (EDR) and KED. Using these technologies, it has been demonstrated that the necessary support can be given to metallurgical process work for REE extraction.

Jan 1, 2014

By Tyson C. Birkett

Initial indicator mineral sampling covering 425,000 square km of northern Quebec and subsequent follow-up of positive results convinced the Ashton ? SOQUEM joint venture to acquire mineral rights to 380,000 hectares prospective for diamond in late summer, 2000. Drilling in 2001 and 2002 identified eight kimberlitic bodies, all significantly diamondiferous. Commercial size stones (retained on a square mesh sieve with openings 0.85 mm) and encouraging grades have been returned by several bodies tested to date: The Renard bodies are formed by steep-sided breccia pipes with kimberlitic matrix surrounded by irregular outboard breccia zones within country rock. These bodies were emplaced in high-grade metamorphic rocks of the Superior Province of Archean age. Orthogneiss with lesser tonalite hosts the breccias, although regionally paragneiss is also present. Diatreme facies portions and nearby country rock are intruded by minor to major (Renard 1) amounts of hypabyssal-facies kimberlitic rock. Renard bodies are macrocrystic, with large olivine crystals set in a groundmass of olivine, phlogopite, monticellite, spinel, carbonate, apatite and serpentine. Proximity of various Renard bodies, with most in a core area of 0.5 square km will allow planning of an efficient mining operation. Geophysics, especially magnetic surveying, has contributed to identifying bodies of kimberlitic rock.

May 1, 2003

By Laxman (Lucky) Amaratunga, Hisham Madi

Final disposal of mine wastewater neutralization sludge continues to be one of more pressing problems in the mining industry. The disposal of mining and metallurgical waste products into underground reduces the environment impact and improves the safety of the mining operation and the economics of the enterprise. This current research focuses on an investigation of utilization of mine wastewater neutralization sludge obtained from Kidd Creek Mine site, as a supplementary material for their proposed deep mine pastefill system. Their proposed pastefill consist of combination of rock aggregate in a matrix of imported sand and tailings with binder (Portland cement + Slag cement). Pastefill mixes containing various percentages of the waste sludge 0 (control mix), 1, 2, 3, and 5% by weight as replacement to the fine sand were prepared and tested with different percentages of binder. Hypothesis behind this approach is to study the behavior of sludge as replacement of sand in matrix as well as its ability to act as a binder. Compressive strength, percentage of sludge, binder dosage, slump, water to cement ratio, percentage of solid, and curing time are being observed. The results indicated that sludge can be incorporated into the pastefill and enhance its strength without compromising the pastefill quality and integrity.

Jan 1, 2004

By A. J. Russell

"This paper investigates why it is critical for a mine to accurately determine thermal rock properties and virgin rock temperatures. Theoretical simulations of deep mining production zones have demonstrated that thermal conductivity (k), virgin rock temperatures and specific heat (cp) significantly impact rock heat predictions which can be the dominant component of a mine’s heat load. Natural variability in these factors showed that realistic errors can have a significant effect on mine heat loads. This can ultimately affect miner safety and introduces risk to the viability and sustainability of a project. INTRODUCTION Accurate heat load determinations are critical to ensure that underground working conditions are maintained within legislated and mine specific parameters to safeguard the safety and productivity of employees. Underpredicting mine heat loads will result in hot underground conditions, which risk the health and safety of employees, reduce the productivity of employees or stop production if legislated temperatures in working areas are exceeded. Overestimating mine heat loads will result in increased capital and operating costs reducing the viability of the project. Over- or under- predicting the heat load for a project will increase the project risk. Heat sources in a mine can broadly be broken into two categories. These two categories are defined by Hemp and Rawlins (2014) as natural and artificial heat sources. Those sources which depend on the size, location and depth of the mining areas are defined as natural heat sources, whereas those heat sources which are a result of the actual mining activities are defined as artificial heat sources. Autocompression, or the conversion of potential energy, to enthalpy is an important consideration when determining the air temperature in the mine and its interaction with natural and artificial heat sources. It is documented by Jones (1985) and Hemp and Rawlins (2014), that the heat flow from rock in deep mines can dominate other heat sources; information from BBE’s archives show that this is between 40% and 60% of the total heat load. They also point out the importance of accurately measuring both the thermal rock properties and virgin rock temperatures (VRTs) for determining and planning the ventilation and refrigeration requirements for a mine. Both of these texts cite multiple methods for calculating the heat-flux and ultimately the heat load for the different working areas in a mine. All of these methods demonstrate that the heat flux and heat load will increase proportionally with increased thermal conductivity (k), specific heat (cp) of the rock or mineral, and VRT depending the area of the mine or mining method."

Jan 1, 2019

By Mahmoud Ahmed

Three-dimensional models are in increasing demand for design, maintenance, operations and construction project management. Point-clouds are the main output of automatic data collection using laser-scanners and photogrammetric technologies. Pipe-works may comprise 50% of the value of important construction projects such as industrial and research facilities. We have developed a practical and cost-effective approach, based on the Hough-transform and judicious use of domain constraints, to find, recognize and reconstruct/model 3D pipes within point-clouds fully automatically. The developed approach allows pipe growing within a 3D point-cloud. It samples the point-cloud to sequential orthogonal slices, detects pipe?s cross-sections within sampled slices and grows the pipe along the cross sections centerlines. It is validated using laser-scanner data from construction of the Engineering-VI building on the University of Waterloo (UW) campus. The system works on a typical laptop. Recognition and localization results are within a few millimeters. The presented approach opens the gate to broad applications of pipe-network modeling.

Aug 1, 2013

By G. Plascencia, C. López, J. González, D. Jaramillo, M. A. Barrón

Air jet and molten matte interaction within a Peirce - Smith converter is analyzed during the first stages of blowing using Computational Fluid Dynamics (CFD), by means of the Large Eddy Simulation and Reynolds Stress turbulence models. Jet velocities ranging from 5 to 150 mis, which involve the bubbling and open jet regimes, were considered in 2 and in 3-D numerical simulations. As a result of the computer simulations, it was found that low velocities results in gas bubbling in the molten copper, whereas higher gas velocities results in well defined plumes. The consequence of such different behaviours results in an increment in the rate of refractory wear or in copper splashing respectively. The analysis of the results may lead to improve the design of the tuyeres currently used in copper converting. Bottom blowing of air is also explored in this work. Numerical results show a strong non-linear parabolic behaviour of the jet velocity on the average velocity of copper; which means that beyond certain jet velocity, the copper de-accelerates thus reducing its velocity. This may be due to the open nature of the jet, which prevents the momentum transfer from the injected gas to the molten copper.

Jan 1, 2007

By C. Caballero, A. Warczok, K. Itagaki, A. Moyano, J. Font

The Codelco Norte Smelter process 2,500 tpd of arsenic-bearing concentrates with an arsenic content of up to 1.5% in one of its two main smelting units, the Teniente Converter. The product, 1,100 tpd high-grade matte or white metal, is traditionally fed to the PS converters, while the 1,700 tpd of slag is fed to the slag cleaning electric furnace for copper recovery. This is achieved in a very reductive environment which reduces the viscosity of the slag and enhances the sedimentation of the high-grade matte droplets. The behavior of arsenic in this non-oxidative environment was studied at lab-scale and fundamental thermodynamic data were obtained. Based on these data a thermodynamicbase model to assess the arsenic behavior in reductive environment was developed. It is based on a mass balance for the reduction and sedimentation stages performed in an electric furnace which allows the recovery of high-grade matte droplets after decreasing the viscosity of the slag. This model can be a very suitable tool for predicting fractional distribution of arsenic in the slag cleaning electric furnace, when the distribution ratio, vapor saturation degree, temperature, y As and pO2 are given.

Jan 1, 2007

By Jean-Yve Tremblay, Michel Prud'homme

"Industrial minerals include a group of more than fifty minerals which are marketed into almost all the sectors of industry; they are the backbone of many manufacturing industries. Table I shows major end-uses for industrial minerals in manufacturing sectors. At Energy, Mines and Resources, industrial minerals are divided in three major categories: (I) agro chemicals and chemicals, (2) construction mineral s, and (3) ceramics and specialty minerals. A listing of the major groups of minerals is shown in Table 2. Agro-chemicals and chemicals are sold on the basis of their chemical content and purity. Construction minerals or structural minerals are distinguished by their performance as low cost and bulky commodities. Ceramics and specialty minerals are performance-specific and are sold for their property on imparting functions on end-products. Industrial minerals have unique characteristics that are useful in many stages of processing; from crushed size to micronized fillers a single mineral ca n serve a broad range of industries because of its intrinsic properties."

Jan 1, 1988

By Dwayne D. Tannant

The Fox Pit at EKATI Diamond Mine reached a depth of approximately 150 m as of September 2005. The pit is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high bench faces. A series of blasting tests were conducted to improve catch bench reliability and increase the percentage of benches that meet an 11 m catch width. The design changes focussed on reducing damage to the bench crest because maintaining the bench crests is the most important factor in achieving good bench reliability. The most significant improvement was obtained by raising the bottoms of the lower trim blastholes by 0.5 m. This change decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. Another improvement was the use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast. This change reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest. As mining and the blast testing progressed, the portion of the bench with crest achievements (>11 m) increased from 57% to 75%.

May 1, 2006

By P. S. Daly

"The purpose of this paper is to describe the types of instrumentation used at Sherritt Gordon's Ruttan Mine to monitor the"" effects of mining. The aim of the monitoring program is to establish parameters to achieve a maximum ore recovery with minimum dilut ion in a safe environment.The copper-zinc Ruttan Mine is in northwestern Manitoba, approximately 760 km from Winnipeg (Fig . I) . Production commenced in 1973 from the open pit at the rate of 10,000 tons per day. Pit bottom lies 58 metres above the first mine level. Underground development has overlapped with open-pit mining throughout. The open pit was phased out in the latter part of 1980.Underground production began in early 1979. The mining method employed in the first lift is sub-level blasthole open stoping with delayed hydraulic filling. Large-diameter (6.5-in.) holes are being drilled in the crop stope area and are also planned for some other areas for vertical retreat mining into a slot. GeologyThe orebody consists of numerous sulphide lenses of variable size, geometry and geology . The lenses occur within volcanoclastic host rocks which exhibit a strong variability in intensity and type of alteration and structural characteristics. Stope design and sequencing were based on these complex geological factors."

Jan 1, 1981

By J. Kicki

The paper depicts the current status of the EKSPERT mining machinery management system and shows the prospects for its further development. The system is the result of a rare attempt to utilize the comprehensive dataset; this refers to a precisely identified group of users and is used to develop a solution with a scope that encompasses other areas of activity within the company. The authors present the incredible flexibility and usefulness of the system used at KGHM Polska Miedz S.A. for everyday control of the mining machinery fleet. The issue of visual aspects of the reports generated by the system is handled separately and used as a tool allowing for implementation of the methodological assumptions of EKSPERT. A concept for creating a system for assisting decision making in the process of mine management with the use of IT tools and production monitoring is also discussed. The solution is based on integration of information from both the monitoring field and visualization of the technological process around the Production Reporting Center.

Aug 1, 2013