Search Documents

By J. W. Bingay

The expansion of the mining industry, with other industries, of course, is dependent upon a supply of fresh capital from year to year. Mining is a speculative form of investment, though there is a wide range of risk as between indiudual undertakings. All of the leading financial writers, nowadays, agree that expansion is being seriously interfered with by the unprecedented load of taxation Canadians are carrying. Individuals have less for investment and corporations are obliged to defer necessary expenditures in order that the demands of the taxing authorities may be met. Naturally, speculative investments such as mining exploration suffer first. Undoubtedly, a great deal of cash raised by taxes, if left in the hands of individuals and corporations for investment and expansion, would have been far more beneficially used and would have developed the country more than any use made of it by the government, in the way of bonusing new industries, or the undertaking of large schemes of development. Government undertakings of this nature are often entered into without a proper knowledge of cost and probable return. Expert expenditure of the same sums by business men or corporations undoubtedly would generally produce more prosperity for the country as a whole. The absolute necessity for lower taxation is being increasingly known to the public at large, and eventually it is hoped that our governments will see the economic impossibility of continuing the present rate of expenditure. The successful Finance Minister of the near future will not be the one who can borrow the most money.

Jan 1, 1924

By P. E. Mather, M. J. M. Krane

Uncertainty quantification is a means of articulating the reliability of model estimations. Models of copper pyrometallurgical processes have been published for decades but discussion of their reliability has typically been terse and qualitative, mitigating understanding of their exact applicability to industrial situations. This presentation shows basic uncertainty propagation and Bayesian model calibration, two powerful uncertainty quantification tools, applied to a reduced order model of copper fire/anode refining. The implications of the uncertainty quantification analyses on the applicability of the model results to industrial practice are then discussed. Finally, other possible applications of uncertainty quantification to copper extractive metallurgy are explored. INTRODUCTION Modern copper production operations, including mining operations through wire drawing factories, are ubiquitously heavily instrumented. Most mine-sites and smelters have large repositories of historical data. That said, much of this data is not exploited to its maximum effect. This proceeding provides examples of using uncertainty quantification (UQ) to maximize the informational yield of the data collected from a fire-refining operation. Anode/Fire Refining is the final pyrometallurgical step in the production of copper anodes; it is an essential and universally employed processing step at smelters (Schlesinger, King, Sole, & Davenport, 2011). Much like the smelting and converting furnaces further up the process stream, anode furnaces are difficult to instrument due to their high temperature and the corrosive and/or caking quality of their offgas. This makes continuous and accurate measurement of the streams leaving the unit operation, e.g. liquid copper, slag, and offgas very difficult. As an example, offgas flowmeters, while providing continuous draft values, could miss the actual draft value by tens of percent due to caking or corrosion. UQ methods account for the uncertainty in process measurements and parameter values; they use a process model with measurements of performance indices to provide better and better estimations of process performance. This proceeding will first introduce a surrogate model for copper fire refining, made from a 1D, transient, reacting flow model of the process presented elsewhere in these proceedings (Mather & Krane, 2019). Discussion of the data used to make the surrogate model, as well as the creation of the surrogate model, will be included. Then, a Monte Carlo simulation will be performed, showing the expected soot production rate based on the surrogate model and assumptions about the uncertainty in the model’s parameters. Finally, the surrogate model parameters will be calibrated in a Bayesian way; this will tell what the actual uncertainty in the parameters are, given a set of observed industrial data and prior assumptions of the observations’ and parameters’ uncertainty.

Jan 1, 2019

By D. E. Deegan, G. Holcroft, T. P. Johnson

"The rising cost of extracting metals from existing traditional deposits, increasingly stringent environmental regulations and a greater awareness of corporate social responsibility issues are all factors in stimulating the examination of mine tailings and small-scale alluvial deposits as a potential source of new raw materials. Furthermore, despite tougher economic times the demand for commodities remains strong, in no small part as a result of the growth of the world’s emerging economies.This combination of social and economic factors looks set to continue in the long term which will encourage greater recovery of materials from previously ignored sources such as mine tailings and ores from alluvial deposits.An expansion in the recovery of useful materials from mining-related activities is likely to require the use of robust and innovative techniques that have a built-in degree of future-proofing; DC plasma technology is one such technology.As a result of its ability to separate the valuable metal and minerals from the waste material while destroying hazardous compounds, Tetronics’ DC arc technology offers an alternative approach to resource recovery from a wide range of mine ores. Harmful cyanide compounds and the vast quantities of water used in conventional hydrometallurgical processing are avoided when plasma processing is adopted. DC arc technology also brings additional benefits, including: the extremely effective destruction of organic materials, the conversion of the inorganic material into a re-useable aggregate and the high tolerance of the process to fine and dusty materials. This paper presents details of Tetronics’ DC arc technology as one of the key pyro-metallurgical solutions available for the recovery of valuable materials from traditional mine ores and tailings, as well as giving specific examples of how the technology has been successfully employed in the recovery of enriched slags, ferroalloys and other metals."

Jan 1, 2016

By J. A. Rogers

"The Arthur W. White Mine (formerly Dickenson Mine) is a structurally controlled, hydrothermal gold deposit. A gold producer since 1948, it has, to December 31, 1990, processed 6.9 million (m) tons (T) of ore grading 0.45 ounces per ton gold (oz/T Au). As of December 31, 1991, Proven and Probable Ore Reserves were 3.2 m. T. at 0.32 oz/T Au. The mine is located just east ofPlacer Dome Inc. 's Campbell Mine, within the Cochenour-Gull.rock Lake deformation zone. It is situated on the hanging-wall side of a southeast-plunging anticline in a sequence of metamorphosed Archean volcanic, sedimentary and plutonic rocks of the Red Lake greenstone belt. Ore-bearing structures, found mainly within basaltic rocks, are brittle within greenschist-facies rocks to the northwest, but become more ductile toward the southeast, in amphibolite-facies rocks. Within and proximal to these structures, carbonate and arsenopyrite alteration decreases, whereas biotite, actinolite, pyrite and pyrrh otite all increase to the southeast.Ore and shear structures occur symmetrically about the northwest-trending, steeply southwest-dipping, flattening foliation . The three most common ore trends are on average: (A) northwest trending with a 55 degree to 85 degree dip to the southwest; (B) north-trending with a 40 degree to 50 degree dip to the west; and (C) due east-west-trending with a vertical dip. In general, the dominant direction of economic gold concentrations are explained and thus predicted by considering deformation style (brittle or ductile), rock anisotropies such as bedding and lithological contacts, and direction/magnitude of relative block movement. Direction ""A"" can be found adjacent to both right- and left-handed faults. Direction ""B "" occurs with dominantly right-handed systems and direction ""C"" is found with predominantly left-handed movement. Major faults active prior to, during, and after ore formation can have offsets in the order of 2500 feet. Movements along these faults were transpressive while their conjugate breaks were dilatant, thus creating zones for alteration and ore solution emplacement. A series of faults , each with offsets up to 30 feet were established under lower temperature brittle conditions during late- to post-ore formation. In more complex zones, formed during more ductile deformation, these faults controlled the localized geometry and, thereby, the depletion and enrichment of ore shoots, causing a high nugget effect.Although an important aspect of production planning and monitoring, grade control is also very important within a complex ore zone so that the nuggets are not missed. Detailed observation of structure at the hand-sample scale and detailed mapping at the stope scale give valuable clues to interpreting the structures on a mine-wide scale. Determining the relative movement along fault structures is very important so that using an action-reaction- type logic, potential dilatant areas can be predicted and targeted for development and diamond drilling."

Jan 1, 1992

By Marketa D. Evans

The mining industry has a significant opportunity to capitalize on its past learnings in order to build better social relationships. The industry?s relationship with society is both critical and under pressure. Rising levels of public opposition and social conflict are already having material impacts on operations around the world. Industry has an opportunity to shape the future direction of this social engagement, build public trust and proactively respond to a material risk to operations, but first it needs to better understand the nature of the challenges and the urgency of addressing them.

Aug 1, 2013

By H. F. Maulson

For the benefit of those who are not familiar with the history of the western Provinces-Manitoba, Saskatchewan, and Alberta-as regards our natural resources, a few words of explanation may be in order before taking up the consideration of the Mines Act of 1930. In 1867, The British North America Act was passed by the Imperial Parliament. That Act, which is our constitution, created a union between the provinces of Nova Scotia, New Brunswick, and Upper and Lower Canada (now known as Ontario and Quebec respectively) under the name of the Dominion of Canada. Provision was made therein for embracing other parts of Canada from time to time. That portion of Canada which today comprises the Provinces of Manitoba, Saskatchewan, and Alberta and the lands to the north of them, was then known as Ruperts Land and the North West Territory. In the year 1670, King Charles II had granted by Letters Patent to Prince Rupert and his associates, known as ?The Governor & Company of Gentlemen Adventurers of England, Trading into Hudson's Bay?, commonly known as the Hudson's Bay Company, the lands and territories therein described, being roughly all the lands adjacent to and west of Hudson's bay; also the gold and silver to be found or discovered therein and other rights as more fully described in said Letters Patent. The land so granted was called 'Ruperts Land'.

Jan 1, 1930

By Edward R. Lauer

Energy conservation is an integral part of Canada's energy strategy. We must pursue conservation and energy management vigorously if we are to remain competitive in domestic and world markets, and minimize our reliance on external energy sources. Energy management in industry is discussed from three viewpoints: (l) as a means of directly improving profitability; (2) as a major factor in the supply picture; and (3) as a significant influence on Canada's balance of payments and over-all economic well-being. The Federal role in promoting a voluntary industrial energy conservation program is described.

Jan 1, 1977

By J. J. Fitzpatrick

"This paper deals with the methods used by Quebec Cartier Mining Company in the evaluation and selection of new haulage equipment and in increasing the productivity of the existing fleet.Selection of new equipment is based upon the comparison, for each model under consideration, of the capital investment required and the estimated operating costs and production rate. The calculation of the production rate is based on a widely used estimating procedure. Actual operating conditions considered in the method include: payload, haul distance, road grade, rolling resistance, loading and dumping times, and operational efficiency. A digital computer is used to handle the large volume of repetitive calculations required. Where a fleet of haulage equipment includes trucks of different size and performance characteristics, the problem exists of assigning each truck type to the different working locations to minimize total cost. Linear programming can be used in the solution of this problem."

Jan 1, 1967

By Cummings. J. B., R. Haworth

"THE OPERATION of the Potash Company of America, Ltd., at its plant near Saskatoon, Saskatchewan, is the result of many years of exploratory and development work, culminating in the construction of a shaft, milling, concentrating and other facilities necessary to the production of potash in a marketable form.The possibility that potash existed in •commercial quantities in Saskatchewan was first indicated in 1943, although it was not until mid-1946, when Bata Petroleums penetrated a potash bed at its Verbata No. 2 well near Unity that substantial in-ter.est was developed in the possible exploitation of this important mineral product.The Potash Company of America, which is the largest producer of pot-ash in the Carlsbad, New Mexico area, a district that has been sup-plying about 90 per cent of the North American potash demand, be-came interested in the Saskatchewan deposits •at an early stage. Its engineers made an intensive study of the western Saskatchewan area in 1947 and continued their review of operating problems throughout the next three years.""Potash"" is the commonly used general term applied to the minerals of potassium, of which there are several. The most common mineral forms in which it is produced are potassium chloride and potassium sulphate. The potash content of potassium compounds is ordinarily ex-pressed in terms of potassium oxide (K20) equivalent."

Jan 1, 1960

By D. Lascelles, J. A. Finch, E. El-Ammouri

Flotation separation is expected to be related to the degree of dispersion of the pulp. For instance, highly aggregated systems may show reduced selectivity, reduced entrainment and increased flotation rate. In an attempt to test the impact of aggregation on flotation, we have taken advantage of the effect of Mg ions. Using combinations of Mg2+ and pH gave a wide variation in aggregation of several Cu-Zn ores (measured by settling rate) and corresponding flotation response was determined by batch tests. The trials were conducted on-site at Louvicourt and Agnico-Eagle. In a majority of cases a similar trend in aggregation and flotation selectivity (grade at given recovery) was observed. At Louvicourt, improved selectivity with increasing aggregation at pH 10.5 was found. At Agnico-Eagle, an analogous association between aggregation and selectivity was observed at pH 11.5. It is suggested that aggregation influences particle entrainment, the increased effective particle size reducing gangue recovery and hence improving selectivity.

Jan 1, 2004

By V. Ushakov, P. Bogdan

Daily production scheduling in a highly dynamic smelter environment has always been a great challenge for the operation management due to a significant amount of uncertainties. Planned and unexpected equipment failures, various energy outages, inaccuracies in flow and mass balancing, manpower availability conflicts and other constraints make the job of daily production planning exceptionally difficult. This paper discusses a general scheduling approach utilized by the production management of the Phelps Dodge Miami Smelter (the Smelter). It also describes logical assumptions and some practical software solutions that have been exploited by the Smelter managers to assist the front line supervisors in dealing with daily planning activities for several years.

Jan 1, 2007

Presentation Agenda ?Background ?OEM Recommendations before RCM ?Operating Context ?OEM Recommendations after RCM ?Reality of Failure ?RCM Deliverables ?Maintenance program optimization ?Spare part optimization ?Implementation ?Further Considerations -Three scenarios ?Summary and Conclusion Background ?P&H Mining?s LCM division performed a RCM study on a ?generic 4100 XPB shovel?in Milwaukee. ?P&H soon realized that the analysis required context -The recommendations were manufacturer knowledge based. -The outcome based on manufacturer requirements. -The strategy was not applicable to all machines, etc. Operator experience and ?local knowledge? are key to the success of an RCM analysis. P&H approached Teck Coal?s Fording River Operation to assist with ?Operating Context?. Teck provided operator and maintainer experience.

May 1, 2010

By Raymond B. Hryciuk

Environmental auditing has evolved rapidly over the last decade — first in North America, then Europe, and most recently in Asia — into a widely practiced discipline designed to provide senior management with assurance that operations are being managed in compliance with established governmental standards, internal company policies, and good industry practices. This paper first examines the evolution of environmental auditing, focusing in particular on three interlocking driving forces: company initiatives, collaborative industry initiatives, and government initiatives. Characteristics of effective audit programs, those that have emerged among the leaders, are discussed, including: objectives, scope, coverage, approach, staffing, and organizational considerations. The author then addresses important future trends and developments for environmental audit program design, content, and coverage.

Jan 1, 1996

By Thomas H. Heine

"The Rabbit Lake uranium deposit is located at 58° 11’00”N.. 103°42'36""W., close to the west side of Wollaston Lake, and approximately 800 km north of Saskatoon. The orebody is hosted by Aphebian Wollaston Group rocks, initially deposited as a series of shallow-water marine sediments consisting, in part, of carbonates and possible saliferous petites. Metamorphism during the Hudsonian Orogeny, peaking at about 1850 Ma, recrystallized the sediments to upper amphibolite grade paragneisses. This was accompanied by partial anatexis. The waning stages of Hudsonian orogenesis appear to be marked by minor granitic intrusive activity.The post-Hudsonian period was marked by a long interval of physical and chemical erosion, resulting in the unroofing of the Wollaston metamorphic complex. The entire region underwent extensive lateritic weathering under tropical to subtropical conditions. Carbonates were especially vulnerable and, in the Rabbit Lake area, suffered extensive solutioning with accompanying formation of collapse breccias. Old zones of weakness also underwent periodic reactivation.It was during this period that uranium was leached from the surrounding meta-sediments by oxidizing meteoric waters, and transported into the karsted and fractured rocks of the Rabbit Lake doline.Athabasca Group sediments eventually covered the deposit, their diagenesis taking place at about 200 °C and 900 bars. This allowed the partial to complete recrystallization of the initial mineralization, resulting in a minimum age of 1281 ± 11 Major ""first""-generation pitchblende. Periodic fault/fracture reactivation modified the hydrologic regime within the deposit, resulting in episodic mobilization and recrystallization of pitchblende and other uraniferous species. This is clearly shown in the open pit at the present time: uranium is being mobilized and recrystallized on damp pit walls as bayleyite and liebigite due to the modification of the hydrologic system by mining activities.The uranium mineralization occurs mainly as fracture fillings, coatings, and impregnations within breccia zones and intensely altered metasediments. Lesser mineralization is intimately associated with phyllosilicates which form the matrix of a carbonate-col/apse mega-breccia. The primary ore mineral is pitchblende, consisting of five generations, and from which a large suite of secondary uraniferous minerals have formed. On a gross scale the metal content of this deposit appears to be simple, consisting almost exclusively of U, but minor Ni, As, Cu, Se, Fe and Co are also present. The eastern limit of the mineralization is defined by a vertically-dipping microgranite dyke - breccia complex, containing high-grade uranium values. The orebody is truncated to the west and at depth by the Rabbit Lake reverse fault. Minor mineralization occurs as fracture fillings in unaltered plagioclasite in the footwall of the ore body. Precipitation of uranium from solution could have taken place by a number of processes. A mobile reductant (methane, carbon dioxide, etc.) may have been generated from graphite present in some of the host rocks of the orebody. Sulphides are also a common accessory and may have aided in the formation of a reducing environment. Phyllosilicates may have acted as adsorbants for uranium, allowing for its fixation. This metal has also been incorporated into the phyllosilicates themselves."

Jan 1, 1986

By W. T. Robson

Introduction Ground failure, violent or otherwise, is a problem to be contended with wherever underground operations are carried out. The character and extent of the failure, whether superficial or of more serious proportions, is determined by a number of factors, among which might be mentioned: the depth and dimensions of the underground workings; the types and distribution of wall rocks; structural features of the ore and enclosing rocks; the degree of metamorphism; the dip of the orebody; concentration of mining operations; the rate of mining; the history of the excavations made on the orebody in question. This last factor implies the consideration of such points as the arrangement and distribution of stoping both past and present, the current sequence of scoping, the type and effectiveness of the support used in old and current workings, and the amount and distribution of unmined parts of the lode. With such a variety of conditions, it is only natural that the situation at one place in a mine will not be the same as that obtaining in another part of the same mine and, more than likely, will be quite different in another property.

Jan 1, 1946

By R. M. Beauchamp

Base metal processing operations often treat process tailings and acid mine drainage using a high density sludge (HDS) water treatment process. Lime is used in this process, which reacts with existing sulfates to form gypsum. When a recycle stream is incorporated in the process, gypsum levels in recirculating water may build up and cause high levels of gypsum supersaturation. Precipitation of gypsum from the supersaturated process water causes many problems. It is speculated that gypsum may precipitate on sulfide minerals and silica gangues in the flotation circuit, resulting in decreased selectivity and recovery. An understanding of the determinants and nature of precipitation may provide solutions to mitigate the formation of precipitates and improve flotation performance. This study showed that both sphalerite and silica exhibited gypsum- or calcium carbonate-like behavior in the respective supersaturated solutions, indicative of a coating of calcium species on the mineral particle surfaces. The addition of copper sulfate and/or potassium xanthate had little effect on the precipitation of gypsum or calcium carbonate on the mineral particles. Sodium carbonate is encouraging as a method to minimize calcium species interactions on sphalerite/silica surfaces.

Jan 1, 2006

By Vishal Shukla, Prateek Singh, D. P. Chakraborty

"Continuous thickening by an operation called sedimentation is the separation of suspended solid particles from a liquid stream by gravity settling. The primary purpose of thickening is to increase the solids concentration of the feed stream. High rate thickeners are designed specifically to maximise the flocculation efficiency. A detailed investigation has been carried out to understand the influence of ore type and operating parameters such as bed level, bed mass, rake arm torque and flocculent concentration on thickening operation. Tata steel’s Noamundi plant data shows that variation in ore type, and operating parameters are major contributors to fluctuation in thickener performance. A lot of research has been done earlier on thickening operation but effect of ore type and operating variables by using plant data was never touched before.In this context, the performance of thickener was evaluated by daily data to study the influence of ore type and operating variables on thickener operation. Investigation shows that friable ore % in feed mix is proportional to slime density because friable ore is porous & brittle in nature. As a result, friable ore generates more fines/ultrafine during communition process in wash plant. Increase in flocculant concentration and bed mass is showing a positive change on high rate thickener performance Investigation shows that optimum bed mass and flocculant concentration is required to achieve desired pulp density in thickener underflow at different feed pulp density (g/cc).INTRODUCTIONOver the years, Iron Ore Beneficiation at Tata Steel, Noamundi has seen varied changes. Depletion of high grade iron and with increasing iron ore throughputs coupled with lowering of the hard ore a subsequent increase in slime generation, slime management and clear water requirement for wet Plant has thrown up myriad challenges. To overcome these challenges, many improvements initiatives were taken by Tata Steel in last decade. One of the major changes is the recent High Rate Thickener commissioning at Tata Steel Noamundi to cater the high iron ore throughput requirement. Slime reporting to Thickener has increased from 1.4 MTPA 2.5 MTPA over the last few decades. The above changes further aggravate the poor settling and dewatering characteristics of the slurry which is being feed to HRT. Considering the above mentioned constraints and stringent environmental implication proper water management has become a major challenge to reckon with. The thickener is used to increase the concentration of the suspension by sedimentation, accompanied by the formation of a clear liquid. In most cases the concentration of the suspension is high and hindered settling takes place."

Jan 1, 2016

By J. E. Dutrizac, J. M. Zinck

Ferrihydrite is often the initial precipitate resulting from the rapid neutralization of Fe(III) sulphate solutions, and it seems to be a major constituent of zinc plant neutral leach residues. The most important parameters affecting ferrihydrite precipitaton are temperature, solution pH and the neutralization rate. Low temperatures and rapid neutralization rates yield poorly filterable ferrihydrite, whereas higher temperatures and slower neutralization rates produce readily filterable precipitates; in all instances, however, the precipitates are two-line ferrihydrite. Significant amounts of Zn are incorporated in the ferrihydrite precipitates, and the Zn contents increase with increasing Zn concentration, pH or temperature. Generally, the sulphate contents of the precipitates decrease as the Zn contents increase, and this may indicate that the Zn is adsorbed on the ferrihydrite. Discrete Zn phases were not detected. Neither Cd nor Tl is precipitated with ferrihydrite, although thallium jarosite co-precipitates with ferrihydrite at high Tl concentrations and elevated temperatures. Virtually all of the Sn added to the solution precipitates with the ferrihydrite, but the tin is believed to be present as intimately admixed amorphous SnO2.nH2O. Although selenite extensively precipitates with the ferrihydrite, selenate remains mostly in solution, likely because of the close similarity of the SeO4 2- ion to the SO4 2- ion which is present in high concentrations and saturates the available sites for anion adsorption.

Jan 1, 1998

By W. B. Morrey

This paper deals with the development of the new cap-sensitive slurry explosives. The history and special features of these explosives are outlined, and recent field trials are described.

Jan 1, 1973

By Douglas R. Piteau

"Assessing the stability of a slope cut in rock is basically a problem of engineering geology - geology, because it involves a sound understanding of the important aspects of geology, such as geological structure, ground water, weathering and other natural phenomena, which all relate to or exist in a geological environment, and engineering, in that quantitative evaluations and calculations are necessary, these being based on mechanics and relating to the strength of the geological materials and the forces causing instability of the slopes. The engineering geologist must make every attempt to. provide, in a quantitative way, information on those geological factors which are necessary for making calculations of the probable stability of the slope. These include numerical assessments of quantities relating to the characteristics of structural discontinuities, rock types, topography, hydrogeology, tectonic history and other environmental factors. Based on the development and extension of these general principles, both preliminary and final slope stability studies of some open pits in South Africa, Swaziland and Zambia have been conducted. Some of the basic concepts and techniques developed to carry these studies out are described."

Jan 1, 1972