Search Documents

By B. Wasmund, B. Haneman, G. Sheehan

Success in implementing new technology for metallurgical processes is not a foregone conclusion: This paper includes a survey of 23 new technology-based metallurgical plant start-ups, in which the authors have identified 7 successes, 9 difficult start-ups, and 7 failures. Success is defined not only as meeting the schedule and budget to the end of mechanical completion; the key goal is a fast ramp up to the full design production level, with minimum plant and equipment modifications required after start-up. This paper sets out the key factors that underlie achievement of a quick production ramp up curve, as determined from the authors' project experiences and a quantitative analysis of over twenty metallurgical plant start-ups, both pyrometallurgical and hydrometallurgical. Thorough test-work and pilot plants, plus appropriate scale-up to the full commercial plant, are key determinants of success in implementing new technology in metallurgical processes. Another critical factor is the number of new elements and their interactions. Project phasing is also particularly important for new technology projects, with appropriate review after each phase to develop a risk mitigation plan for the subsequent phase. New technology projects need committed champions to advance the project in the face of sceptics, but also require dispassionate and unbiased experts to ask the hard questions. As a project evolves, it is important to periodically question the appropriateness of assumptions, as well as to re-assess the relevance and completeness of data from test-work I pilot plants I industrial analogues. Sufficient human and financial resources are required to complete the often arduous implementation phase. During the ramp-up period, the operation generates little positive cash flow; however, significant expertise and capital are required for the de-bottlenecking projects that are often necessary to reach the plant's design output level.

Jan 1, 2011

By S. Lun Sin

In this study, the effect of silicon on the microstructure, mechanical properties and hot tearing susceptibility of permanent mould cast AZ91E magnesium alloy was investigated. Varying amounts of silicon (0.5, 1.0 and 1.5 wt.%) were added to AZ91E in the form of an Al-53 wt.% Si master alloy. The phase formation, grain size and solidification behavior of each alloy were characterized and related to their tensile properties and hot tearing susceptibility. The results showed that the addition of silicon resulted in the formation of Mg2Si particles. The presence of these particles led to an increase of the hardness, but was detrimental to the tensile strength and elongation of AZ91E. However, silicon significantly reduced the hot tearing susceptibility of AZ91E. This was attributed to the reduction of the grain size and the decreased freezing range of AZ91E, which contributed to improve the interdendritic feeding during the last stage of solidification.

Jan 1, 2011

By A. P. LeBis

This article attempts to relate the concept of utility to the risk involved when only a small number of projects (compared to their probability of occurrence) are accessible to a firm and to quantify utility when other financial and physical parameters are known.

Jan 1, 1978

By N. Shi, T. G. Joseph

ABSTRACT: An interactive cable shovel simulation has been developed to mimic any shovel dipper geometry for a given cable shovel operating in any homogeneous face material. This interactive cable allows the user to predict shovel performance in any face material encountered and track both its ground stability and the dipper-ground interaction. An embedded Microsoft® Visual Basic spreadsheet was used as the platform for developing an interactive simulation that allows for maximum user-defined parameter input and interactive visual output. The result is an analytical dipper-ground interaction solution that yields crowd, hoist, and digging effort as a function of face activity position.

Jan 1, 2011

By M. A. Upham

"MINING is Canada's second largest basic industry, producing material with a gross value of 2.5 billion dollars, led only by agriculture with 2.9 billion dollars. It pro-vides employment, directly and in-directly, for three quarters of a million people. Since the Second War, the value of mineral production in Canada has tripled. Economists forecast that over the next 15 years its value will triple again. Canada is a basic and leading supplier of nickel, iron, copper, zinc, lead and uranium. It is also a major oil producer, leads the world in the production of asbestos and in five years will be the leading producer of potash, a basic constituent of fertilizer.It can be seen that Canada's wealth and economic progress lies in being a primary producer of economic minerals and in building secondary industries to manufacture finished products from these raw materials. Canada's future in the field of mineral production looks bright, with our resources just starting to be tapped. Outside of the large expanse of Soviet Russia, we are by far the world's most fertile mineral exploration area."

Jan 1, 1967

By Eric J. Grimsey, Don C. Ibana, David E. Grimsey

The segregation process as applied to nickel laterite ores involves the formation of gaseous nickel and iron chlorides which are subsequently reduced to form ferronickel on the surface of a solid carbon reductant. A fundamental study of the process has been carried out using limonite, nontronite and garnierite ores. The study highlighted the significant impacts that ore mineralogy and carbon addition have on the amount of nickel which is segregated rather than retained within the ore due to in-situ reduction. These important aspects affecting nickel recovery and the success of the process are discussed in this paper.

Jan 1, 2017

By John Galbraith, Dwayne D. Tannant, Chris C. Langille

"Development of underground openings in a deep mining environment requires a support system that is able to absorb energy as a result of dynamic loading due to rockbursting and blasting and static loading due to convergence as the development face advances. The support system must be resistant to corrosion and be effective over the life of the excavation, upward of ten years, yet simple and cost effective to install. Over the past two years, research has been conducted at INCO’s Creighton Mine to try and identify a one-pass grouted support system that will meet these needs.The main problem faced, with simply using grouted rebar at depth, is the effect of tunnel convergence on the stiff grouted bolts. Typically, if fully grouted, stiff rebar are installed to the face of an advancing development heading, the amount of convergence that occurs can result in failure of the bolts at the face plates used to attach the mine screen to the back. An initial support is required to enable crews to continue the bolting cycle in the immediate term, yet allow for this convergence over the longer term as the drift advances. The ideal support system will allow both to occur, giving effective immediate support while providing long-term effectiveness in allowing convergence to occur while maintaining the capacity of the bolt.This paper will investigate the expected convergence in deep development headings at +2200 m (+7200 ft) through the use of direct measurements using both flex rod extensometers grouted into the back of a development heading and five-point tape extensometer stations. Measured results will be compared with simple2-D numerical analysis to evaluate the anticipated convergence expected to be absorbed by the bolting system. The required convergence will then be compared with load deformation response of several support configurations."

Jan 1, 1996

By K. J. Boser

"Medium Voltage (MV) metal clad switchgear is referred to as the voltage class from 2.4 kV to 38 kV. Technological advances in circuit breaker designs over the last 20 years have given rise to retrofit options in lieu of complete replacement for older outdated circuit breaker technology. This paper examines the four MV breaking techniques that exist in industry and investigates various retrofit versus refurbish options for switchgear modernization and life extension. IntroductionThe life extension and upgrade of medium voltage circuit breakers is becoming an increasingly important issue in today’s modern industrial facilities from both a reliability and safety standpoint. Unscheduled downtime, loss of production, and plant safety issues are just some of the concerns that need to be addressed with aging switchgear. A thorough examination of the available breaking mediums allows an informed decision to be made when the time comes to assess equipment performance. If you look back over the history of medium voltage breakers, you will find that there have been four breaking techniques developed and widely used:• air magnetic;• minimum oil;• vacuum; and• SF6.Many facilities that were constructed 25 to 30 years ago relied on air magnetic or minimum oil circuit breakers in their distribution systems. At the time, these were the only “tried and tested” options and they afforded good service. Since then, however, newer technology has given us the vacuum and SF6 mediums which have both proven their reliability and monopolized the market. All the methods have their particular place in industry and what follows is a summary of the advantages, disadvantages, and chronological development of each breaking technique."

Jan 1, 1998

By A. Supomo, H. Resendiz, C. Burbidge

"Freeport-McMoRan Inc. (FMI) commissioned the expansion of the Morenci Metcalf concentrator in 2014. The concentrator included many design and equipment innovations, including the first-of-its-kind Metso Hydraulic Roll Crusher (HRC), variable speed ball mills and variable speed crushers. In addition to the innovative design, FMI commissioned the Metso APC team to design a realistic process simulator and the plant APC. The process simulator was utilized to train operators before commissioning, which led to a smoother plant start up. The plant APC utilized the concept of dynamic constraint control, which controls the feed to the primary ball mills by “pulling” the tons from crushed rock storage bins, which then automatically are filled by the upstream HRC and secondary crushing circuits. The primary ball-mill control also adjusts the water addition to the cyclone clusters to avoid overload and achieve sufficient grind size. The constraints include in-circuit constraints for feeder capacity, screen-deck capacity, ball mill power, cyclone mass flow, pump capacity and pump motor capacity. The APC system was implemented shortly after the start of commissioning and immediately demonstrated increased throughput and an ability to highlight and quantify process constraints and bottlenecks. The following paper outlines the control strategy, discusses system implementation, results and challenges.INTRODUCTION The FMI Metcalf Concentrator is located in Morenci Arizona on the site of the old original Concentrator. The new Metcalf concentrator started operation in May of 2014. This plant was designed for an average of 63,500 tpd (70,000 stpd), increasing the total Morenci concentrator complex production to a nominal 113,400 tpd (125,000 stpd). The process flow diagram is shown below in Figure 1.The process consists of primary crushing feeding a coarse ore stockpile followed by secondary crushing operating in closed circuit with vibrating screen decks. The screen undersize feeds the first of its kind Metso hydraulic roll crusher (HRC) operating in a closed circuit with vibrating screens. The primary crusher is a Metso 60x110 gyratory crusher. Secondary crushers are Metso MP1250 Crushers with variable speed drives. Secondary crusher discharge is recycled to the dry screen feed bin and screened with oversize returning to secondary crushing and undersize feeding the Metso HRC3000. The product from the 3.0 meter X 2.0 meter roll crusher is wet screened with the undersize feeding the grinding circuit, which is comprised of two each 24-foot diameter by 40- foot-long variable speed ball mills running in parallel with each in closed circuit with a cyclone bank of 12 cyclones. The wet screen oversize is recycled to the HRC feed bin."

Jan 1, 2019

By D. C. Downing

"I THANK YOU for the invitation which The Mining Society of Nova Scotia extended, originally to Gordon Berry, manager 'of our Point Tupper Refinery, to join you at this meeting and discuss refining and petrochemicals in their relation to this region. There are natural advantages in Nova Scotia which have made possible, and will continue to make possible, sizeable developments both in petroleum refining and in chemicals. Equally, however, as is the case everywhere, there are certain constraints. For clarity in this presentation, I will state some of these constraints right at the beginning. First, of any future developments from now on, only a small proportion of the products can be expected to go into local markets. I can make the point best with a few figures. Petroleum companies all have market forecasts. None ever work out to be perfect, but the trends are relatively predictable and the orders of magnitude are certainly correct. Estimates for the use of all refined petroleum products in the four Atlantic provinces are:"

Jan 1, 1973

By Ellie Condolios

Hydraulic hoisting offers a number ~f attractive features over conventional hoisting methods: small shaft space requirements; great flexibility of layout, including pick-up or delivery of the material at points distant from the mine shaft; low investment and operating costs. However, limited practical experience with this type of hoisting dictates that careful design and, frequently, extensive testing be done by competent engineers before large-scale installations are built. This paper covers the following: basic laws and design criteria for hydraulic hoisting installations; a description of a coal hoisting installation which has been in industrial operation since 1960, with a vertical lift of 600 feet and an annual capacity of 500,000 tons of -3 ~-in. coal; and a tentative appraisal of the process, including cost estimates. THE transportation of solids in water flowing through a pipe-line has, for a number of years, been common practice in dredging, public

Jan 1, 1963

By W E. vanSteenburgh

The Polar Continental Shelf Project was initiated in 1959 to provide an administrative and logistic vehicle for research in the physical sciences of the land, sea and channel area of the Arctic Archipelago. Most of the scientists are supplied on secondment from the professional branches of the Department. The yearly expeditions number some eighty scientists and sub-professional staff, and they are supported by a fleet of fixed-winged aircraft and helicopters. Accurate positioning is obtained by the use of a Decca Lambda navigational system which is moved as the area of interest is shifted. The Project is designed to accommodate not only physical scientists, but to provide facilities for other scientist who may have an interest in the area under study. The main research scope of the Project includes topographical surveys, hydrography, oceanography, geology, including marine sedimentary studies, gravity, magnetics, seismology, glaciology and geography. The Polar Continental Shelf Project was initiated and recommended by the Committee on Northern Development in 1958.

Jan 1, 1963

By M. Board, R. Pakalnis, S. Seldon, R. Brummer

The Kidd operation mines roughly 10 000 tpd of copper and zinc ore from underground and employs about 700 personnel. In the late summer and fall of 1997, major movements in the proximity of the east wall of the Kidd open pit had been observed. The Kidd pit had been mined from 1965 to 1977 to depths of 260 m (850 ft), followed by subsequent mining by underground methods to current depths in excess of 1830 m (6800 ft). The No. 1 Mine (2600 Level to pit bottom) is approximately 90% extracted, with most of the remaining reserve between 2000 and 2500 levels. Although initial concerns centred on the stability of the pit walls, the potential ramifications of the movements to the underground were recognized and measures were implemented to ensure the safety of personnel as well as to minimize the potential damage to existing operations. In late October, damage to underground operations was observed as deep as the 2000 Level. In the final assessment, the global mobilized mass was a “wedge”-shaped hangingwall block extending from surface to about 610 m (2000 ft) below surface. The “wedge” boundaries are defined by a fault and shear zone which have continuous lengths in excess of 1070 m (3500 ft); its base by shearing through the host rock mass; and its eastern face by deep tension cracks (Fig. 1). Mined and filled excavations at the western face of the “wedge” allowed mobilization of a mass in excess of 30 M tonnes. Movements in excess of 75 cm (30 in.) per day were recorded on the surface stations that preceded the complete shutdown of operations on October 29, 1997. The evaluations in the days following the shut-down were centred on mitigation of immediate and future possible negative impacts on infrastructure and mining of the remaining No. 1 Mine reserves while ensuring the safety of the operators. This effort required the rapid assessment of the potential damage of the block movement on underground infrastructure, stope access, drainage and ventilation, as well as airblast potential due to the falling of a large block into the pit near the ventilation intake at the base of the pit. These assessments were presented in a previous paper (Seldon et al., 1999). In total, the lateral movement of the block on the ground surface was over 4.3 m (14 ft). This paper describes the detailed studies performed to understand the failure mechanism and to assess the impacts on future mining in No. 1 Mine.

Jan 1, 2000

By H. C. Gunning

Introduction Considerable attention has of late been attracted to the area surrounding Nimpkish lake, on northern Vancouver island, by the discovery of important rich copper deposits. In less than two years some 200 mineral claims have been staked in a small area, and at least two groups have very promising surface showings. During the summer of 1929, the writer spent one month investigating the general geology and mineral deposits of the region, and, although no detailed work has as yet been done in the field or in the laboratory, the importance of the mineral discoveries and the lack of geological information available to the public warrants a preliminary paper on the district. The district is, from a mining viewpoint, very accessible. Boats from Vancouver call at Englewood, in Beaver cove, four times a week. From Englewood, a first-class logging railway, operated by the Wood, .English Company, extends to the northeast corner of Nimpkish lake. The fifteen-mile trip from the north to the south end of the lake is made by boat, two tugs being maintained by the logging company. The whole trip from Englewood can easily be made in one day. The known mineral deposits lie immediately east of the southern part of the lake, four miles or less from the shore. A fair trail, four miles ? long, leads from the lake to the Nimpkish Copper group. Apart from this trail and an old logging railway grade which follows the east side of Klaanch river for several miles, no trails exist on the southeast side of the lake.

Jan 1, 1930

By J. R. D. Gravel, D. A. Poland

"The induration of iron ore pellets has always utilized prefired pellets to protect the pallet cars from the environment of the induration furnace. This paper presents the process used to obtain superior upper sidewalls. These heat resistant castings are used on induration pallet cars, and their life improvements by as much as 400% is a significant step towards the reduction of the prefired (or hearth layer pellets.) The benefit to the industry in the removal of the hearth layer is improved overall productivity. IntroductionThe Iron Ore Company of Canada (IOC) operates with production facilities located in Labrador City, Newfoundland and Sept Iles, Quebec. It has recently been acquired by North Limited, an Australian based resource oriented company. Prior to its acquisition, IOC has examined several methods of operational cost reductions. One of these was an examination of indurrating pallets. Pallets are composed of numerous assemblies and sub-assemblies. The examination of the upper sidewalls began as an intent to increase the operational life of the component. The anticipated net effect was to be a reduction in the overall pallet maintenance cost. All of the components and assemblies have undergone a severe scrutiny. IOC has found that the success of the project has depended upon not only the technical competency of all parties involved, but also upon the ability to share risk, to be innovative, and to find a partner with whom the development can proceed without fear and yet with accountability. IOC has found in Cast Steel Products (CSP) such a partner in the field of pallet development. This paper will undertake to explore the progression into the arena of partnering between IOC and CSP. CSP and IOC met in the fall of 1994. The work of re-engineering the pallets began with an initial order for 36 pallets in March, 1995. The work on the upper sidewalls involved segregation of the effect of alloy development versus physical geometry development. The nature of partnering between the two companies allocated alloy development to IOC and physical geometry development to CSP, yet no advancements were made in either area without the close co-operation or the involvement of both partners."

Jan 1, 1999

By V. Budinsky

In recent years the global mining industry has addressed its social and environmental responsibilities and numerous factors have contributed to this. Corporate Social Responsibility (CSR) is an important part of mining company strategy for practical implementation of the goals of sustainability, transparency, accountablity and good relationships with stakeholders:- investors, employees and communities. A key stakeholder for all mining companies is the local community which is affected by the mining operations. Companies must identify the emerging social and environmental trends, study the interests and concerns of various communities, address their needs and maintain a positive relationship. The CSR programmes of Czech coal mining companies are focused on surrounding community initiatives and sustainable responsible business. Mining in the Czech Republic is subject to strict rules and regulations and supervised by the State Mining Authority. Mining projects undergo rigorous approval procedures which encompass all operational measures at the different planning levels ? such as public participation in the authorisation process for mining projects, the application of the Environmental Impact Assessment Directive, environmental sustainability programmes, innovative solutions and flexible options offered by the mining company. One very important part is the preparation of the mining-technology preconditions and developing the integrated planning process in which all socially and politically relevant subjects in the mining operation surroundings are included. In an in-depth debate, all stakeholders may jointly develop the concept, in accordance with democratic principles. The optimally conducted dialogue process needs broad communication bases, including setting up theme-related joint taskforces, together with good moderation and the highly qualified support of technical experts. Using a case study of Severoceske doly a.s. Chomutov (SD Company) and the Czech Coal Group ? Czech leaders in the extraction of brown coal, this paper aims to examine the community development approaches and the CSR effectiveness of large scale mining companies. This paper brings a review of CSR and other such voluntary initiatives in the mining industry's proactive steps to contribute to societal well-being in a meaningful way. Key studies are provided by the projects ? Region with Better Perspective?, ?Stop Dust for Healthy Brezno Village?, ?Clever Heads for the North? and ?Coal Safari?. CSR issues are managed throughout all stages of the mine operation and beyond, long after the mine closes (e.g. post-closure programmes of new landscape, alternatives for reclamation including generation of lakes in former surface mines, conceptualization of industrial heritage). Communities need to be given the opportunity to help themselves through participation in CSR projects rather than being recipients of financial gifts from the company. A fair balancing of interests is the basis of any successful cooperation.

Aug 1, 2013

By Brian G. Pewsey

Located in the northern part of the Province of British Columbia, the Cassiar Mine started development of its asbestos orebody in 1952, and is currently producing 105.000 tons of asbestos fibre annually. The townsite is nestled in a beautiful valley and supplies more than average facilities. The fibre is shipped to more than 40 countries and is used in many industrial products.

Jan 1, 1978

By C. V. Deutsch, O. Babak, J. G. Manchuk

High levels of geological heterogeneity occurring over relatively short distances pose a challenge to the unconventional open-pit techniques used in oil sands mining. There is strong motivation to mine selectively and minimize dilution and loss; however, the large equipment and high mining rate used to meet production targets tend to reduce selectivity. A numerical model is developed to account for geological complexity, mining equipment, regulatory criteria, and other operational parameters. This framework is used for more accurate forecasts, optimization of equipment, and other operational decisions. An example demonstrates the approach in light of Alberta Energy Regulator criteria.

Jan 1, 2014

By Marsh A. Cooper

THE THEME of my remarks provides a great deal of latitude. I shall therefore take advantage of the scope it offers to look at our industry across a broad spectrum. My observations reflect a Canadian mining man's varied career as a geologist, mine operator, geological consult ant and company executive in Canada and overseas ... under differing cultures, business environments and political jurisdictions. I was fortunate to come into this industry in the mid-1930's when it was characterized by great enthusiasm, drive and resourcefulness. It was the beginning of a burgeoning era of some 30 years' duration in which the individualist, the entrepreneur and the builder found ample room for expression. As I contemplate the environment in which we now have to operate and try to perceive what lies ahead, I find myself deeply disturbed. Something serious has happened to this industry along the way. It appears that our very success has been the source of our undoing. I believe it is useful to summarize our industry's basic strength at home as a take-off point f or assessing its position in world terms. I hope that I can focus on some of the things that, in my view, must be done for this industry and by this industry to restore Canada's historic role in the world mining community. The Canadian mineral industry provides 140,000 jobs. It pays the second -highest average weekly wages and salaries among the country's major industries. The output per employee in the mining industry is estimated at about three times that for the economy as a whole.

Jan 1, 1977

By T. L. McCall

CHANGES in mining practices have evolved so quietly and unobtrusively that perhaps we scarcely appreciate how truly startling these changes are unless we cast our minds back so as to compare the past with the present. Such retrospection is, indeed, necessary when attempting to forecast the future, for it is only by carefully reviewing the past that we can hope to obtain an indication of what the future may hold in store. In this instance, it is not necessary to delve into the very early history of . coal mining, as our purpose will be served if the last three or four decades are reviewed, a period that is still fresh within the memory of many of us. These earlier days might be termed the selective period of mining, for at that time the coal resources of the world had not been tapped to anything like the extent they are at present and this condition enabled the owners and operators to exercise selective powers and only mine such seams of coal as could be most easily reached an worked at the lowest possible cost and which, at the same time, would suit the requirements of the market. Carrying this thought of selective mining still further, the miner, who was then an artisan skilled in all the branches of his calling, was able to select or discard such parts of the seam he was working that the co al sent out of the mine was acceptable to the consumer with just the barest minimum of preparation. Compare these conditions with the? conditions prevailing today, when coal seams of medium height, good quality, and readily accessible have been largely depleted and the operator has been compelled either to carry on his operations under much greater depths of cover where the coal is more costly to win, or else to work seams of lesser height or of poorer quality.

Jan 1, 1938