Search Documents

By W. R. Smith

Introduction No commercial deposits of silica sand are known to occur in British Columbia, so all requirements for foundry and other uses must be imported. During the war, nearly 5,000 tons per year were used, all originating in Illinois and delivered to local consumers for about $12.00 per ton. Present requirements are somewhat less, but the cost is still of the same order. The relatively high cost of silica sand in British Columbia is not only a serious item for present consumers, but might be a deterrent to the establishment of a glass industry, should this be contemplated at any time. The present investigation was undertaken in an attempt to provide a cheaper source of silica sand within the Province. In 1936, a large number of beach and bank sand deposits in the lower coastal region of British Columbia were examined by the British Columbia Department of Mines, and samples were analyzed chemically and mineralogically. The deposits over the whole area proved remarkably uniform in mineral composition, consisting essentially of quartz, feldspar, ferromagnesian minerals, rock fragments, and various accessory minerals, and differing only in the relative proportions of the various constituents. In no case did the quartz content of any sand exceed about 40 percent and the average was of the order of 20 to 30 percent.

Jan 1, 1947

By L. Bichler, A. Siebert-Timmer

In this research, novel YSZ ceramics doped with 5 mol% Nd2O3 were manufactured via Spark Plasma Sintering (SPS) process. The sintered Nd2O3-YSZ ceramics were subjected to a static supercritical water environment at a temperature and pressure of 400 °C and 31 MPa, respectively. The weight loss and microstructure development of the sintered ceramic before and after exposure to supercritical water was studied. The results suggested that Nd2O3 addition significantly improved the degradation resistance of the YSZ ceramics. This was attributed to the improved phase stability of the 5 mol% Nd2O3-YSZ ceramics, since X-ray Diffraction (XRD) studies showed that the cubic stabilized matrix in these ceramics was retained after exposure to supercritical water. In comparison, pure YSZ ceramics exhibited a rapid degradation behavior as well as a phase change.

Jan 1, 2014

By Dan Currie, Tom Lamb, J. Coady Marsh, Gary Landry

"This paper describes the Cape Breton Development Corporation's experience with the Lovat M-300 tunnel-boring machine at the Donkin-Morien Mine. Between January 3 and December 21, 1984, the 7.6 m (25 It) diameter TBM advanced 3350 m (10 990 ft) . The authors will describe experiences with the machine and highlight the implications of tunnelling machines to underground coal mine development in Canada. IntroductionThe Cape Breton Development Corporation (CBDC) has recently completed the drivage of a 7.6 m (25 ft) diameter tunnel, 3.5 km (2.2 miles) in length , to access the Harbour Coal Seam at the Donkin-Morien Project. The tunnel was successfully driven with the first Canadian rock tunnel-boring machine (RTBM or TBM), designed and built by Lovat Tunnel Equipment, Inc. The initial mine development consists of the drivage of two tunnels to the first major coal seam. Future plans are proposed for the development of a 4 million tonne-per-year mine (Marsh et al., 1983, Gillman, 1982), which will require the drivage of a further two tunnels and could access up to four coal seams. The tunnel cross-sectional areas were designed to provide sufficient ventilation area and access for a production of 4 million tonnes per year."

Jan 1, 1986

By G. A. Bezuidenhout, J. Davis, S. M. Bradshaw, J. P. T. Kapusta, D. K. Chibwe

"This research work forms part of an assessment to complement the feasibility of implementing high pressure sonic injection into relatively small (2.25 m I.D by 3.66 m I.L) Peirce-Smith converters (PSC) used at Lonmin Plc. Work has been carried out to characterize the fluid dynamics of three-phase (air, matte and slag) fluid flow in these converters using Computational Fluid Dynamics (CFD) simulations. The investigation has been done to study the flow pattern of the three phase system at high air pressure injection achieving sonic velocity at the tuyere exit into the converter. The 2-D and 3-D simulations of the three phase system were carried out using the volume of fluid (VOF) and realizable k -e turbulence models to account for the multiphase and turbulence nature of the flow, respectively. These models were implemented using the commercial CFD numerical code FLUENT. A detailed study of the flow pattern has been presented in the form of contour plots and the results obtained are useful for understanding plume extension and velocity distribution, shear wall stress distribution, and phase distribution characteristics in the system. The results provide a basis for further development of sonic injection technology into relatively small industrial Peirce-Smith converters with the ultimate objective of achieving lower energy consumption, improved process efficiency and increased throughput of the converting process. INTRODUCTIONPeirce-Smith converters (PSC) have been used in copper (Cu) and nickel (Ni) making smelters for more than a century for the purpose of removing iron (Fe) and sulphur (S) chemically associated with copper-nickel mattes through exothermic oxidation reactions. This process is commonly referred to as conversion. In principle, conversion is a submerged injection process, where typically air (or oxygen enriched air), at subsonic velocity (typically < 150 m/s), is laterally blown into liquid matte (Cu-Ni-Fe-S system). Oxygen preferentially reacts with Fe and S to produce iron oxide (FeO), which is slagged off, and sulphur dioxide (SO2), which reports to the process off gas."

Jan 1, 2012

By A. Aubin, H. Yang, G. Zaluski

The Athabasca Basin of northern Saskatchewan and Alberta is an exceptionally rich metallogenic region, hosting more than 2.8 B lb U3O8, of which over 927 M lb U3O8 have been mined out since extraction first started in the late 1970’s. A detailed compilation of several empirical features of 85 deposits located within the basin was conducted in order to understand the distribution and variability of the geological characteristics of the mineralization and its associated alteration. A new empirical classification was devised based on four parameters: 1) geometry of the mineralization (dimensions and relation to the unconformity surface), 2) size, grade and metallurgical complexity of the mineralization, 3) lithostructural setting, and 4) extent and nature of associated alteration haloes. This compilation defines the footprint characteristics of the Athabasca Basin deposits, which guides decision-making processes from early exploration and discovery to resource expansion and extraction.

Jan 1, 2020

By Henry C. Knight

A number of improvements in the techniques of budgetary control have been developed in the 1970&apos;s. The most significant of these is zero-base budgeting. This procedure is a marked improvement, because it overcomes some of the key weaknesses inherent in most traditional approaches to budgeting. It incorporates techniques and disciplines which improve the quality of both the budgeting effort itself and the documents that most senior managers will need to evaluate. The end result is a budget that establishes and improves cost effectiveness. This budget is based on resource allocations using cost-benefit criteria and on a system of prioritization for making funding choices. Zero-base budgeting is applied only to costs and expenses that are not conducive to control using industrial engineered standards. Therefore, the benefits attributed to zero-base budgeting will only hold true for administrative, selling, exploration, safety, fire protection and overhead, and other indirect types of costs and expenses. It is in this context that the question of its attractiveness for the mining industry is dealt with.

Jan 1, 1978

By K. D. Bulin

"An interesting brief history review of shovels as the primary excavating tool will permit the reader to see that immeasurable development and resources have preceded the shovel excavators which today are used extensively throughout the mining industry. With this as a background, the shovel manufacturer has the ability to utilize his resources best in those areas of shovel development in which the maximum benefits of increased reliability, performance and ease of maintenance will improve the operating rewards to the user of the equipment. The author explains the function of the shovel as a part of the material handling system. A detailed description of those areas of the shovel in which the most recent developments and major improvements have been implemented in the manufacture of the shovel excavator arc included."

Jan 1, 1973

By J. Laganiere

A considerable part of the sulphuric acid requirements of the Aluminum Company of Canada&apos;s Arvida smelter comes from the burning of 180-200 tons per day of zinc &apos;"&apos;sulphide concentrates in a 22-ft.-diam-eter fluidized bed roaster. The plant and its operation were fully de-scribed in a publication that appeared about ten year ago (1). A simplified flowsheet of the roasting and gas-cleaning sections of the plant is given in Figure 1. The wet zinc sulphide concentrates are un-loaded into a pug mixer, by means of a Pay loader, and mixed with water in a mixing tank to make a slurry of 80 per cent solids. The slurry is transferred to a .feed tank and then introduced into the roaster at a point four feet above the constriction plate, which is the height of the settled bed of zinc calcines. The roasting temperature is con-

Jan 1, 1963

By M. Harrison, C. H. Stockwell

"Metals vah1ed at more than $200,000,000 have been obtained, mainly since 1930, from the mines of northern Manitoba. The greater part of this production has been copper, zinc, and gold from the Flin Flon, Sherritt Gordon, and Mandy mines. The chief mines from which gold alone has been produced are God's Lake, Laguna, and Gurney. At present (May 1947) Flin Flon and Sherritt Gordon are the only producing mines, but the Nor-Acme property is being developed for large-scale production of gold. Large deposits of nickel and copper are being diamond drilled at Lynn Lake, and the Thompson, Ferro, and other properties are being developed. The mineral deposits lie within irregular or elongated areas of Precambrian sedimentary and volcanic rocks, surrounded by granite ( Fig. 1).The common rock types include basic and acidic flows, agglomerate, ruff, greywacke, arkose, argilli te, conglomerate, and their gneissoid and schistose derivatives. They are invaded by sills, dykes, and irregular bodies of gabbro and diorite, and all are cut by granite. Some of the sediments are interstratified with volcanics, and others are deposited unconformably on them.STRUCTURAL GEOLOGYLittle is known of the structures of the rocks in the area as a whole, because by far the greater part is unexplored or has been covered only by reconnaissance surveys. Available information indicates a general east structural trend in the southeast part, whereas in the west part the folding is mote complex with no definite overall trend. However, in a few small areas in the western part where detailed work has been done, as around the Flin Flon, Sherritt-Gordon, Nor-Acme, and other properties, the structure is fairly well known. The following descriptions apply chiefly to these areas ."

Jan 1, 1954

By T. Johnson, D. Kelley, J. Graham

"Hydrometallurgical processes can be exceptionally corrosive. Conditions associated with metal extraction and refining require materials of construction that can withstand process acids and acid chlorides at temperatures up to 90°C (194°F). Process vessels, piping, scrubbers and ducting can be rapidly compromised in these aggressive environments if not designed with care. Design engineers are challenged to find materials that can stand up to hydrometallurgical processes especially for copper, zinc, nickel, cobalt and uranium. This paper will evaluate material solutions to determine which provides attractive economics for initial procurement as well as high durability for reasonable life cycle costs.INTRODUCTIONMining activity in a number of metal ores has been running quite high over the last few years. In particular, those metals that employ acid functional extraction processes such as copper, nickel cobalt and uranium have been particularly active.The world’s largest nickel mine – the massive $4.76 billion Ambatovy nickel mine on the African island nation of Madagascar is nearing completion. When it reaches its full production capacity in 2013, the mine will produce 60,000 MT/yr of nickel and 5600 MT/yr of cobalt. Coming on the heels of the Ambatovy project is the Long Harbour Processing Plant in Newfoundland, Canada which will process the ore from Vale’s Voisey Bay mine in Labrador. Voisey’s Bay is expected to generate more than 50,000 MT/yr of nickel ore when it starts up in 2013. Next up will be the Boleo project in Mexico on the Baja peninsula. When commissioned in 2013, the $858 Million Boleo project is expected to produce 60,000 MT/yr copper, 3100 MT/yr cobalt, 36,000 MT/yr zinc and 100,000 – 250,000 MT/yr manganese carbonate.High nickel alloys and rubber lined steel have been used for decades to design corrosion resistant equipment for mineral processing environments. These materials demonstrate reasonable resistance to corrosion for most environments. Unfortunately, higher nickel alloys are quite expensive. Rubber lined steel is a bit more affordable but requires continuing service over time which ultimately drives up its cost as well. FRP (Fiberglass Reinforced Plastic) has also been used extensively in mineral processing for tanks, piping and ducting employed in aggressive environments. Today, more and more design engineers and material specifiers are calling for FRP composites for both new and replacement equipment used in the refining and processing of a variety of metal ores."

Jan 1, 2012

By J. T. Liu, G. H. Han, W. C. Chai, Y. F. Huang

"In beneficiation process, metal ions could adsorb onto clay mineral surfaces or interact with flotation chemicals, and then result in the flotation behavior changing of desired minerals. Al(III) is the dominating ion existing in the bauxite flotation system. In this research, the adsorption behaviors of Al(III) on two silicate clay minerals (including bentonite and kaolin) were investigated by means of UV-Vis spectra, zeta potential testing and scanning electron micrograph analysis. The adsorption experiment results show that the adsorption capacity of clays for Al(III) ions increases with the initial Al(III) concentration, contact time and solution pH. There are some different adsorption behaviours for two clays. Increasing the clay concentration decreases the adsorption capacity of bentonite, while increases first then decreases for kaolin. Higher temperature favours the adsorption of Al(III) on bentonite but goes against for kaolin. The adsorption capacities of bentonite and kaolin for Al(III) respectively reach 12.48 and 0.875 mg/g at initial solution pH 5. Zeta potential results show that the adsorption of Al(III) on two clays is characterized by electrostatic attraction mechanism.INTRODUCTIONIn beneficiation process, there is inevitably a wide variety of metal ions generated from mineral crushing, mineral dissolution and water chemistry conditions. Metal ions adsorb on the mineral surfaces or interact with the beneficiation agents, affecting the flotation efficiency of desired minerals (DiFeo et al., 2001; Parolis et al., 2008; Shackleton et al., 2012; Shengo et al., 2014). Therefore, it is necessary to have a detailed investigation on the adsorption behaviour of metal ions on clay minerals.Having good ion exchange capacity and negative surface charge, the clay minerals could take up various metal ions from the mineral-water system. Bentonite and kaolin are very common aluminosilicate clays in the mineral processing system. These two clays both hold a permanent negative charge, =X- on the basal surfaces, and a smaller variable charge, =SiOH on the mineral edges (Gu & Evans, 2008; (Gu et al., 2010). Adsorption experiments are usually used to study the adsorption affinity of metal ions for clay minerals (Sen & Bhattacharyya, 2012). The adsorption of Zn(II), Cu(II) and Pb(II) onto natural bentonite showed that the adsorption amounts of metal ions increase with contact time, solution pH and metal ion concentration, but decreases with adsorbent concentration and system temperature (Sen & Gomez, 2011; Melichova & Hromada, 2013). Cr(III) adsorption on bentonite was significantly pH dependent. The adsorption process followed pseudo-second-order model and the equilibrium adsorption was consistent with Freundlich isotherm (Lollino et al., 2015). The adsorption behaviours of Pb(II), Cd(II), Ni(II) and Cu(II) onto kaolin indicated that increasing pH favoured the adsorption of metal ions (Jiang et al., 2010). The adsorption of Cd(II), Cu(II), Pb(II) and Zn(II) onto kaolin showed that an ion-exchange reaction occurred at pH<7.0 and inner-sphere surface complexes were prone to form at higher pH (Srivastava et al., 2005)."

Jan 1, 2016

By K. C. Hendrick

The paper will review the significant developments in world copper over the past ten years and their impact on the Canadian industry. It will also examine the outlook for the future.

Jan 1, 1971

By J. J. Barakso, C. Tarnocai

This paper outlines a method of testing for the mercury content of rocks, soils and plants. Techniques of sample collecting are described and the analytical procedures outlined. Examples are given of mercury determinations in two known mineralized areas in British Columbia - Copper Mountain Mines and Pacific Nickel Mines.

Jan 1, 1970

By Kenneth L. Graham

Horizontal directional drilling from existing underground workings will greatly reduce, if not replace, surface exploration drilling. Diminishing ore reserves along with increasing difficulty in acquiring access and permitting of drilling surface holes requires a change in procedure. The length and direction of the required long holes is site specific, but once determined could be quickly mobilized. Data would be available for a much more timely evaluation without any surface disturbance and required reclamation issues. Preplanned directional drilling from underground will also provide an evaluation of already inconsistent uranium deposits located under surface terrain that is inaccessible to surface drilling.

Aug 1, 2010

By K. Shen, A. J. Sinclair, N. Champigny

"Fluid inclusion studies from the Cinola deposit indicate low salinities and low C01 contents of the ore fluid. This supports a suggestion that the mineralizing fluids originated from pore water in the fluviatile host rock (mid-Miocene Skonun Formation). Bimodal distribution of filling temperatures suggests the existence of at least two temperature regimes centred on 160°C and 270°C during mineral deposition. Independent age and stratigraphic evidence indicates that depth of mineralization is between 1.1 and 1. 8 km, corresponding to a hydrostatic load of between 110 and 170 bars.RESUMELes donnees sur les inclusions fluides du gisement Cinola indiquent de basses salinites et basses teneurs en C01 . Ceci confirme que les fluides mineralisants ont ete derives de l'eau interstitielle prise dans les sedimentsfluviatiles hates. La distribution bimodale des temperatures d'homogenisation implique !'existence de deux regimes de temperature concentrees vers 160°C et 270°C pendant Ia mineralisation. La profondeur alaquelle le gisement s'est forme est evaluee d'etre entre 1.1 et 1.8 km a partir d'informations stratigraphiques independantes: ceci correspond a des pressions hydrostatiques de 110 a 170 bars."

Jan 1, 1982

By J. E. Reeves, J H. Morgan

Certain non-metallic minerals are used widely as fillers in the manufacture of many Canadian products. The first part of this paper deals in a general way with deposits of such minerals and their mining, with the concentration and preparation of the minerals for market, with specifications of the consumers, and with methods of control of the products to meet the specifications. The second part of the paper de-scribes talc as a specific example of mineral filler. Its production and uses in Canada and the possibility of producing higher grades of talc are discussed. Some suggestions are made for meeting the needs for mineral fillers as Canada's industry expands. RELATIVELY few people are sufficiently aware of the vast and important role that is being played in our everyday lives by mineral fillers. Many kinds of paints, papers and plastics, to mention three major classes of industrial products, are literally loaded

Jan 1, 1961

By S. R. L. Harding

"Introduction0N MAY 2th, 1953, Socony Seaboard Pembina No. 1 well, located 70 miles west-southwest of Edmonton, was completed as a producer of high-gravity oil from the Cretaceous Cardinm sand. This event is possibly the most significant in the development of the oil industry in Western Canada since the Devonian discovery at Leduc in 1947. The result of the Pembina discovery and the follow-up drilling has been a tremendous increase in interest in the Cardium formation.Descriptions of the Cardium formation, as it occurs in the 'Central Foothills' and in the 'Southern British Columbia Foothills' have been presented by R. E. Folinsbee (9)-and C. R. Stelck (21), respectively. The purpose of this paper is to discuss the more regional aspects of the subject.The name Cardium was first used .as a stratigraphic term in 1863. Dr. James Hector ( l2), geologist attached to Captain John Palliser's exploratory expedition, gave the name 'Cardium to the whole section of marine Cretaceous beds exposed along the Bow river west of Calgary."

Jan 1, 1955

By E. Swartzman

"DURING 1951, experimental cleaning studies on both fines and larger sizes of certain Canadian coals were conducted on a relatively large scale in two pilot plants in the United States, large enough to be considered as small commercial units, and in one commercial plant in Canada.One of the pilot plants was a wet washer of a type which apparently has never been .used in Canada, nor has any Canadian coal been tested in it before. In the other pilot plant and in the commercial plant, dry cleaning equipment was used. The commercial plant is the first of its kind to be employed in Canada, and this type is used only to a limited extent in the United States.Fine-Coal Cleaning ExperimentsTest PlantsHydrotator and Hydrotator-Classifier combination pilot-plant with a capacity of about twenty tons per hour. This is a classifier type washer adapted for cleaning fine coal as well as certain intermediate sizes. The Hydrotator deals with that portion of a coal retained on approximately a 24-mesh Tyler sieve, whereas the Hydrotator-Classifier deals with the minus 24-mesh fines."

Jan 1, 1952

By S. Sundararajan, Z. Lin

ABSTRACT Fierce market competition and demand have made it imperative for mining companies to achieve higher productivity and operational efficiency. The selection of the best mining method and equipment combinations will enable companies to meet production and efficiency targets. Continuous mining is increasingly preferred by companies for its high efficiency and low unit costs. We developed simulation models for two continuous mining systems: the continuous surface miner (CSM) system and the at-face slurrying (AFS) system. Considering two different case studies, the paper discusses application of developed models to determine the optimal number of trucks and equipment capacities for the two systems.

Jan 1, 2013

By Bryon Cerklefskie, Michael Schulte

"This case study explores the usage of polymer ducting as a replacement to curtains and FRP for face ventilation in two coal mines. There are two mines looked at, one is the highest elevation underground coal mine in North America, the other is the gassiest mine in North America. The paper details the trials of both mines switching from FRP and curtain respectively to polymer ducting. The results discuss the ability for the mines to not only achieve consistent airflows and keep them in compliance but the unexpected positives. Mine A was allowed to do longer cross cuts due to increased air volume at the face. This drastically cut their costs of mining down due solely to modification of the ventilation cycle. Mine B saw economic benefits due to longer cuts between place changes. Both mines have documented lower dust, methane, noise, and improved wear and tear on their equipment as a result.INTRODUCTIONThe emergence of longwall mining in underground coal operations has resulted in new ventilation challenges. Numerous production crews strive to complete their development sections with enough time to adequately prepare for the upcoming longwall panel. Continuous miners will cut out two or three entry development sections per their ventilation plan, that is approved and controlled by MSHA (Mine Safety and Health Administration), which will drive amount of footage that can be mined at a time prior to installing roof support. At this moment the continuous miner, hereafter referred to as the CM, will back out of the entry and moves to the second entry to complete a similar cut. Typically, a roof bolter crew will pull in to the finished cut section and install ground support. This is called a place change style of production coal mining. There is an alternate method that includes a miner/bolter combination as well but that was not featured at either test site in this case study. Ventilation has to be provided to sweep the working face of each entry to control dust and gasses. Each task will have an MSHA prescribed ventilation requirement dependent on the dust levels and methane emissions of the rock for that particular mine. The CM, roof bolting and unused headings will each require constant ventilation but at different volumes. Since each working face is changing throughout the mining cycle the ventilation requirement in a working heading is never static and is changing with the working task.Traditional Ventilation ControlsTraditionally face ventilation for coal mining operations has been completed thru the usage of a curtain system and\or using auxiliary fans and ventilation tubing. Room and pillar mining systems typically utilize curtain systems, which use curtain walls that are installed by the miners by erecting wood framing and covering it with brattice curtain. This splits the drift width to allow fresh air to sweep the face and take the contaminated air and dust behind the curtain to the ventilation exhaust\return area of the mine. This method is difficult to adjust the airflow from entry to entry during changing cycles and requires that a wider drift is mined out in order to have enough room for the brattice wall. In operations that require roof bolting, this method limits the length of the cuts from the CM prior to advancing and can lead to not providing enough ventilation to keep dust and methane levels below compliance requirements."

Jan 1, 2019