Search Documents

By J. R. Shore, F. G. M. Gillett, E. J. Zickar

"The addition of fines to rod mill feed has been employed at Inco Metals' Frood-Stobie Mill since 1973. The fines, which act as a ""lubricant"", causes an increase in the pulp fluidity and assists the flow of feed through the rod mill. Fines addition was one of the main factors which led to improved rod mill performance and the elimination of rod mill tangles.This paper outlines the testwork performed in evaluating the addition of fines, and summarizes the beneficial effects on rod mill grinding efficiency, throughput rates, power consumption and noise level. INTRODUCTIONFrood-Stobie Mill is situated within the Frood-Stobie mining complex, on the southern rim of the Sudbury Basin. The Mill commenced operations in November, 1967, and has since processed in excess of sixty-five million tons of ore. Minus 8-inch ore is delivered to the Mill's coarse ore bin by two surface conveyor belts from the Frood and Stobie Mines, while Little Stobie ore is transferred by underground conveyor and hoisted directly into the coarse ore bin a long with additional Stobie Mine ore."

Jan 1, 1981

By Farzad Mohammadi, Patrick Littlejohn, David Sanguinetti

Arsenic levels in metal concentrates are increasing as mining companies turn to developing low grade and complex ores. When arsenic bearing minerals are smelted, arsenic deports as gases which must be neutralized by a scrubber system. The resulting scrubber effluent is high in dissolved arsenic and requires treatment before the wastewater can be discharged or re-used. Conventional arsenic removal relies on lime addition followed by calcium arsenate formation and precipitation as hydroxides. As an alternative, arsenic removal with sulphide precipitation is receiving more attention due to potential advantages of the technology. Process streams high in arsenic often contain concentrations of dissolved metals that may be selectively recovered during sulphidization, producing a product that can be reprocessed and reducing waste generation. This paper will review laboratory testing completed for arsenic removal through sulphide addition and precipitation of arsenic (III) sulphide in combination with metals recovery to offset arsenic removal costs.

Jan 1, 2014

By Kent Zehr

Suncor Energy Inc. is an integrated producer and refiner of oil and gas headquartered in Calgary, Alberta. The bulk of revenue comes from the Oil Sands Group (OSG) operating in the McMurray formation of the Athabasca Oil Sands. Located some 25 kilometers north of Fort McMurray, Suncor OSG began life in 1967 as Great Canadian Oil Sands, the first operator to successfully enter commercial production of synthetic crude oils from the area. For most of the last decade, dramatic growth has been the standard mode of operation for Suncor OSG. Production of synthetic crude first reached 100,000 barrels per day in 1997 and less than five years later is averaging in excess of 200,000 barrels per day. Within this dynamic organization, Suncor Extraction is the business unit that processes run-of-mine ore into clean diluted bitumen for Upgrader feedstock. Extraction also delivers and places the barren sand and process affected water into tailings storage in one of several ponds from which water is recycled to support the various processes. For reference purposes, Extraction on a typical day currently receives more than 400,000 metric tons of oilsand ore, which is all processed to water based slurry for separation in one of two extraction plants. Separated tailings are disposed of as a slurry and the cleaned bitumen froth is diluted with naphtha and sent to tankage for storage until required by the Upgrading Unit. As a consequence, on a typical day Suncor Extraction pumps more than 1,000,000 tonnes of aggressive slurry into and out of the two extraction plants.

May 1, 2003

By B. Szpunar

Structural and mechanical changes of urania are investigated when oxidized to U3O8. The CASTEP ab-initio quantum mechanical program, employing density functional theory is used. The total energy technique is implemented to investigate changes in the lattice constants. The ab-initio calculations predict a 36% increase in the volume per uranium atom when transforming from UO2 to U3O8, which agrees very well with experimental data. The implication of this prediction on the linear expansion and fuel fragmentation is discussed. The calculated elastic constants of urania are in good agreement with experiment. The predicted mechanical properties of UO2 and U3O8 are compared.

Aug 1, 2010

By Trung Nguyen

Midwest is a unique uranium deposit with exceptionally high arsenic content. The ore body is located 17km west of the McClean Lake operation. The McClean Lake mill will be modified to process Midwest ore and handle solid wastes coming from the Midwest water treatment plant. This paper describes the modifications required of the McClean Lake mill, process challenges associated with treatment of the arsenic, and the possibility of recovering nickel and cobalt as a by-product. It also reviews the complexity in the design of the Midwest water treatment facility which incorporates reverse osmosis technology with conventional physical-chemical water treatment.

Aug 1, 2010

By Weldon Li

Outline ?Introduction and Motivation ?Previous Research ?Details ?Findings ?Current Multi-Piece Mining Wheel Research ?Methodology ?Preliminary findings ?Current and Future Activities ?Summary and Closing Remarks

Oct 1, 2010

By C. A. Young

"The stabilization of tailings has been a matter of concern to the Mining Industry for many years. In earlier times, when mines were small and only high grade ore deposits were mined, the problem was not a great one. But, more recently - during the last 30 to 40 years - the increased world demand for various metals, combined with the vast strides that have been made in the improvement of metallurgical extraction processes, have resulted in the development of lower grade ore bodies.About 30 years ago The International Nickel Company started experiments to stabilize the surface of the tailings and prevent them from becoming a dust source under certain weather conditions. The use of chemicals to form seals, covering with crushed stone, mulching with straw and some early seedings were some of the stabilizing methods tried. Results were either unsuccessful or impractical economically.In 1954 a series of experiments to establish vegetation on the tailings began. Varying degrees of success were achieved but however unsuccessful a particular scheme turned out, the attempt to find a solution was never written off. As we look back, we realize that the first significant break-through came as the result of three test plots planted in the spring of 1957. Each plot covered an area of approximately one-third of an acre. One plot was successful and persisted until it was covered up by the expansion of the tailings area in 1961.In 1960 a review of all our test plots to that date was carried out to assess the factors which effect the chance of grass being established."

Jan 1, 1969

"The Dome Mine, located in South Porcupine Ont. has been in operation since 1910 and is owned and operated by Placer Dome Inc. The current milling facilities were constructed in two phases with the first being commissioned in 1982. It consists of a grinding, gravity separation, thickening, and leaching circuits. The second phase was commissioned in 1988 with the addition of the CIP, stripping, electrowinning, and carbon regeneration circuits.It is now common practice in the gold processing community to add liquid oxygen to leach circuits to increase both recovery and kinetics. Along with these benefits the metallurgical group at the Dome realized the potential to replace compressed air with liquid oxygen as a source of oxygen for the dissolution of gold. A plant trial of liquid oxygen was undertaken during the fall of 1991. The results of this first test were favourable enough to warrant further investigation, and a second plant trial was conducted in December 1991.The data generated as a result of each trial revealed that oxygen could be economically substituted for compressed air as a source of dissolved 02. The energy savings in required horsepower enabled a rapid payback period. Thus the project was approved in the spring of 1992 and l should be operational during the final quarter of 1992. INTRODUCTIONIn a continuing effort to reduce operating costs and improve recovery at the Dome mill it was decided to investigate the feasibility of adding liquid oxygen (02) to the leach circuit. It is now common practice in the gold processing community to add 02 to the leaching process to increase both kinetics and recovery. It was anticipated that an increase in kinetics would allow us to eliminate one or more leach tanks while maintaining acceptable recoveries. The metallurgical group felt that along with these benefits, the potential was also there to reduce power consumption through the reduction in the processing of compressed air which is quite costly (12 cents/1000 cubic feet per minute in 1991)."

Jan 1, 1993

By M. R. Coffin

In recent years, improved operation of the Kidd smelter has resulted in an increase in blister production capacity. Due to manpower and equipment limitations anode production and treatment rates could not be increased without incurring significant additional operating expenses. The option chosen to expand casting and refinery capacity to meet the available blister supply was to increase the anode thickness while maintaining the same anode exchange cycle in the refinery. This has resulted in a cathode production increase of almost 10% for minimal expenditure. Equipment and process modifications required to cast and refine the thicker anodes are discussed in this paper, along with the Six Sigma methodologies used to identify them. Key areas covered are Hazelett continuous caster operation, refining process parameters, plating performance and cathode quality.

Jan 1, 2007

CI, Data and Data Systems Road Analysis Control Quick and simple manual Analysis Case study Visual relation of analysis

May 1, 2013

By Gordon. I. M., J. Blackshaw

"The wet part of the Hollinger mill is housed in two buildings, the grinding plant and the treatment plant. In the grinding plant there are four 7xl5 ball mills which grind the ore to 60 per cent through 200 mesh. There is also one 7xl5 ball mill which grinds table concentrate to 9 5 per cent through 200 mesh.The primary classifier overflow is pumped to the treatment plant where it passes over shaking tables, producing a concentrate and a tail. The concentrate pulp is pumped to the grinding plant for secondary grinding. The secondary classifier overflow is pumped back to the treatment plant where it is thickened in two 40xl 5 tray thickeners and agitated in four 20x24 mechanical agitators arranged in series of two (with 2 spares).The table tail pulp is thickened in nine primary 40xl5 tray thickeners (with 2 spares). The thickened table tail pulp and the concentrate agitator discharge pulp are mixed and pumped to four rows of 15x45 pachuca agitators, arranged in series of five tanks.The pachuca discharge pulp is divided. The smaller part goes to two rows of 3-step decantation using 40xl5 tray thickeners (with 2 spare rows). The larger part goes to six 14xl6 drum filters. The repulped primary filter cake and the thickened pulp discharged from the decantation rows are fed to eight 14xl6 drum filters. The secondary filter cake is mixed with water and pumped to the tailing line."

Jan 1, 1968

By L. Li

To accommodate the large payloads and harsh operating conditions associated with heavy vehicles in the mining industry, off-the-road (OTR) tires are typically used with heavy mining vehicles. These tires have increased abrasion and wear resistance due to their thicker tread, sidewall and bead thicknesses. Given these features, OTR tires are much stiffer than conventional passenger vehicle tires and cannot be mounted to a single-piece rim without damaging the structural integrity of the tire during the mounting process. Therefore, multi-piece wheels are used with OTR tires to facilitate mounting. While these assemblies are necessary, several instances of their failure have been reported to result in injuries or fatalities within the mining workplace. Many of these failures were specifically reported to be caused by the disengagement of the wheel lock ring - a component used to securely engage the assembly during operation. In this study, a threaded-connection locking mechanism has been proposed in place of the traditional lock ring design. The performance of this threaded-connection was numerically evaluated in a pull-out test against a conventional five-piece wheel assembly. The pull-out test was devised as a means of quantifying the engagement ability of each wheel?s locking mechanism. A high degree of modelling accuracy was maintained throughout the analysis by validating the vertical and horizontal static loaddeflection behaviour of the rim model of the five-piece wheel assembly against experimental data. Through validation, the model data were found to be within 10.5 and 4.80 %, for vertical and lateral loaddeflection behaviour, respectively. Results from the pull-out analysis found that the threaded-connection demonstrated a 113 % increase in the force required for disengagement to occur relative to the conventional five-piece design - a force of 9,550 kN in total.

Aug 1, 2013

By Ahmad Ghahreman, Denver Cowan, Yeonuk Choi

"Previous testwork by the authors has indicated that both granular coconut shell based activated carbon and a new microporous carbonaceous bead, Lewatit® AF 5, are highly effective in improving the oxidation kinetics and decreasing the elemental sulphur yield when assisting the atmospheric oxidation of pyrite. While the two carbon catalysts show similar results and improvements to the pyrite oxidation, there are differences between them. For example, the activated carbon assisted oxidation showed faster kinetics than the AF 5 assisted oxidation, while elemental sulphur seemed to remain adhered to the surface of the AF 5 after oxidation when much of the elemental sulphur formed during the activated carbon assisted tests was found in the oxidation residue. The objective of this paper is to investigate the differences between the two catalysts through the use of scanning electron microscopy, photography, Raman spectroscopy, surface chemistry analysis, and Brunauer-Emmett-Teller (BET) surface area analysis. With this investigation the authors should be able to achieve a better understanding of the surface chemistry of the two carbon catalysts (i.e. functional groups, charges, acidity etc.) and help explain the strengths and/or the weaknesses of the catalysts when applied to the atmospheric oxidation of pyrite.INTRODUCTION Previous research conducted by the authors, indicated that both a granular coconut shell based activated carbon (activated carbon) and a microporous carbonaceous bead, Lewatit® AF 5 (AF 5), acting as a catalyst enhanced atmospheric pyrite oxidation in ferric sulphate media by approximately 40% when compared to unassisted oxidation and that elemental sulphur yields were increased from 23% to approximately 69 and 63% when assisted by AF 5 and activated carbon respectively (Cowan, Jahromi, & Ghahreman, 2017). The study indicated that although total pyrite oxidation assisted by the two catalysts was similar, differences were noticed in the impact that the two catalysts had on the outcome of the oxidation. Kinetic curves in the Cowan et al. study indicated that atmospheric oxidation of pyrite seemed to reach completion after 48 hours of oxidation when assisted by activated carbon. A similar trend was noticed in the kinetic curves for oxidation when assisted by AF 5, however the oxidation curve did not reach completion until approximately 96 hours (Cowan et al., 2017). This observation indicated that the kinetics of pyrite oxidation are enhanced by both catalysts, oxidation kinetics are much faster when assisted by activated carbon rather than AF 5."

Jan 1, 2017

It?s a pleasure to be with you in Vancouver today to reinforce the good work you and your companies do to develop and operationalize new technology as a lever to improve operational performance and reduce our impact on the environment in absolute terms. Although I will use the work we do at Shell to reinforce this perspective, the principles apply to all of us in this industry regardless of whether you are a producer or supplier. I?d like to help demystify the future of Canada?s oil sands based on Shell?s view of global energy developments, including forecasted demand. One of the incontrovertible truths of this era of global energy defines change as an unchangeable law of progress. Another tells us that the art of progress is to preserve order amid change and to preserve change amid order. These axioms help frame the increasingly public debate about the future of Canada?s oil sands. I hope to illustrate how Shell?s commitment and investments create positive progress that embraces change amid order in the oil sands. I?m going to spend a little time today to focus the spotlight on the future of the oil sands to help demystify Canada?s hydrocarbon energy future. To do that, I?ll identify the features of our future energy security, including three hard truths about global energy that drive Shell?s business imperatives. Then, it?s instructive to examine Canadians? current consciousness about oil sands sustainability.

Oct 1, 2009

"These standards were developed by the CIM for use with the value or worth of a Mineral Property as opposed to “evaluation” where the key objective is an economic assessment or determination of the economic merit of a propertyP1 .0 BACKGROUNDPl.1 There are at present no comprehensive standards for valuation of Mineral Properties in the Canadian mining industry. The Mining Standards Task Force (MSTF) of the Toronto Stock Exchange and the Ontario Securities Commission in its Final Report (January 1999) specifically recommended that the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) form a committee of valuation practitioners to review and advise on approaches to valuation of Mineral Properties.Pl.2 On May 5, 1999 at the Calgary Annual General Meeting, CIM Council approved the formation of a Special Committee on Valuation of Mineral Properties (CIMV al) to be co-chaired by Keith Spence (Chairman of the CIM Mineral Economics Society) and Dr. William Roscoe (Roscoe Postle Associates Inc.).Pl.3 The mandate of CIMVal is to recommend Standards and Guidelines for Valuation of Mineral Properties to be used by the mining industry in general and to be adopted by Canadian securities regulators and Canadian stock exchanges.Pl.4 The members of CIMVal represent of a mix of professional disciplines and experience in the field of Mineral Property valuation:Keith N. Spence (Co-chair), Alliance Pacific Resources Inc., TorontoWilliam E. Roscoe (Co-chair), Roscoe Postle Associates Inc., TorontoMichael J. Bourassa (Secretary), Aird & Berlis LLP, TorontoChristopher R. Lattanzi, Micon International Limited, TorontoRoss D. Lawrence, Watts, Griffis and McOuat Limited, TorontoPaul E. Lunney, Noranda Inc., TorontoCraig A. Roberts, Pacific International Securities, VancouverDavid A. Scott, CIBC World Markets, TorontoIan S. Thompson, Derry, Michener, Booth & Wahl Consultants Ltd., VancouverWilloughby A. Trythall, retired Placer Dome executive and consultant, Vancouver"

Jan 1, 2003

By G. S. Hume

"THERE HAS BEEN a marked growth in the petroleum industry in Canada since the end of the war. The rate of growth in the demand for oil products has exceeded that in United States, although the per capita consumption is still less. Estimates of the consumption of petroleum and petroleum products in Canada in 1951 are approximately 154,000,000 barrels, which is slightly more than 11 •barrels per capita, whereas the estimated consumption in United States for the same period, according to World Petroleum, is placed at 2,619,- 970,000 barrels. This, on the basis of a population of 154,000,000, would be equivalent to 17 barrels per capita. The increase in consumption of the petroleum and products is world wide. World production in 1951 has been estimated (Oil and Gas Journal) at 11,700,000 barrels a day or more than 41;4, billion barrels for the year. United States production increased 13.7 per cent to 6,143,000 •barrels a day and Canada'.s ,, total production increased about 65 per cent from a total of 29,091,235 •barrels in 1950 to an estimated (Dominion Bureau of Statistics) 48,096,800 barrels in 1951.The trend to use increased amounts of petroleum and petroleum products, particularly in the United States and Canada, has also been supplemented by increased use of natural gas. The rate of expansion of the consumption of natural gas in United States in the past few years has been very rapid, increasing from 2,600 billion cubic feet in 1940 to 5,975 billion in 1950, with the proven reserves in the same period increasing from 85,000 billion to 186,000 billion cubic feet."

Jan 1, 1952

By John Shirokoff, Ladan Khaksar

"Cyclic polarization technique and also potentiodynamic measurements were applied to study corrosion behavior of 13% chromium steels in chloride containing environment. Potentiodynamic measurements were performed at 25 and 75 °C with 0, 10 and 20 g/l NaCl in 0.01 M hydrochloric acid solution. At the same time, the significant pitting parameters such as corrosion potential (Ecorr), pitting potential (Epit), protection potential (Epro) and passive current (Ipass) of cyclic polarization curves with various NaCl concentration were analyzed and compared to describe the corrosion behavior of 13% chromium stainless steel. Surface measurement techniques such as SEM and EDS were used for morphology and analysis of corrosion products. The results showed that both temperature and Cl- concentration had significant effects on corrosion behavior of 13% chromium stainless steel in acidic solution.INTRODUCTION Of all the corrosion resistant alloys (CRA) used in oil and gas developments, martensitic stainless steels (MSS) are some of the most common ones these days. These steels not only have the advantages of normal steels: high strength, cost-effective, easy to manufacture, available in a wide variety of product forms, but they also have good CO2 corrosion resistance at higher temperatures as a result of their 11% minimum chromium content. One of the most common types of MSS used in the oil and gas industry is 13% chromium steel. NACE and API standards both reference several different varieties of 13% chromium steels for use in oil and gas projects(“Corrosion Resistant High Cr Steel for Oil and Gas Wells,” 2013). All types of 13% chromium steels have about 12 to 14% chromium and other minor alloying additions, and can be placed into two general groups: conventional and modified. Conventional 13% Cr steels (13Cr) are those most common in oil and gas, some of which are CA6NM (UNS J91150), AISI 410(UNS S41000), and AISI 420 (UNS S42000). These alloys have excellent corrosion resistance when compared to carbon steels up to about 300°F (150°C) and are used for a variety of wellhead, tubular, and downhole components however they have very limited resistance to cracking in H2S (Vallourec Group, 2015). Modified 13% Cr (M13Cr) steels came from the need for increased corrosion resistance at higher temperatures, increased H2S cracking resistance, and increased yield strength above 85 ksi (586 Mpa) primarily for tubular goods and other downhole equipment. These features were developed by taking a conventional 13Cr steel and adding nickel (Ni), molybdenum (Mo), copper (Cu), and other alloying elements. M13Cr provides better corrosion resistance than 13Cr up to about 350°F (177°C), yield strengths up to 110 ksi (758 Mpa), and also improved H2S cracking resistance(“Corrosion Resistant High Cr Steel for Oil and Gas Wells,” 2013)."

Jan 1, 2017

By Geo. D. Furse

"The information that has accumulated regarding the geology of the McIntyre mine is the result of work by several geologists and, as might be anticipated, their conclusions have varied. The writer has been at the mine only a few years and due to wartime conditions has not been able to study and review the mine's geology as thoroughly as his predecessors. Where the writer's conclusions differ from those of previous authors, it should be noted that he has been unable to re-map all the workings in which flow contacts are exposed, but has endeavoured to describe the structure as indicated by the evidence he has been able to observe. He wishes to thank H. G. Skavlem and H. S. Robinson for their constructive criticism of this paper, and McIntyre Porcupine Mines, Limited, for permission to present it. A list of references is appended.The McIntyre mine is in the central part of the Pearl Lake section of the Porcupine gold area. It includes the ""bed of Pearl lake, twenty-two claims to the north of the lake, and the Platt Vet lot to the southeast. It is bordered on the west by the Hollinger and on the east by the Coniaurum property. The chief ore-bearing veins on the upper levels lie very close to the north shore of the lake, but some occur under the lake, and others of lesser importance are found to the southeast. The most important veins are Nos. 3, 5, 7, 10, and 25. Some of the veins extend into the Hollinger. on the west and others cross the east boundary into the Coniaurum. The total production since the commencement of milling in 1912 to the end of March 1947 has been $168,448,218 in gold and silver from the milling of 17,690,963 tons of ore."

Jan 1, 1954

By James S. Redpath

"AbstractThis paper is an attempt. to outline the present status of underground mining contracting in Canada, and to present certain facts concerning the writing and administration of underground mining contracts which, hopefully, may be useful to those intending to engage a mining contractor . The paper is based on the author' s experience as a contractor and also as a consulting engineer advising others in the purchase of contractors' services.HistoryIN THE early days of mining contracting in Canada, the contractor was primarily a labour contractor. He was expected to bring a good crew of men that normally followed him, and to perform certain work under his own direct supervision. The owner usually looked after all other details including financing, payrolls, withholding taxes, etc , computing and paying the contractor his profit. In the pre-World-War II years, most work was done on this basis.Over the years, the contractor was called on to supply more in the way of services, and the present-day situation evolved.Labour contracts are still used, but now the contractor is expected to carry out his own administration. Most contracts now call for the supply of special tooling required to do the work. In most cases, some, if not all, supplies are the contractor 's responsibility and , in a growing number of cases, the contractor is responsible for such items as design and surveying. The ultimate in this direction is the execution of projects on a turnkey basis. Under this system , the contractor carries the project to a stage where it is turned over fully operational to the owner."

Jan 1, 1977

By C. R. Whittemore

PROGRESSIVE industrial organizations have recognized the importance of maintaining an adequate reference library of volumes covering all phases of their particular branch of industry, but it has been the experience of the writer that few engineers know how to use to the best advantage this store of extremely -valuable information which has been accumulated for their service. Nor does the average engineer appreciate the fact that it is only through the current technical literature that he can keep abreast of the rapidly developing fields of engineering. The present-day ramifications of the engineering field are of such wide scope that the human mind is not capable of storing away more than a small fraction of the information available on any particular topie; yet, from time ? to time, such information would prove invaluable. An engineer can know intimately only a small part of his own branch of engineering; but he cannot afford to neglect to take the fullest possible advantage of all that is already known in his own particular field. Technical information may be obtained by one or more of the following methods: (1) by enquiring of the individual who knows; (2) by performing the experimental investigations necessary to ascertain the facts; (3) by consulting the technical literature, where a record may be found of the work of others. This last method is the one we wish to examine. Our main consideration is the question of how to use the library, but first it is necessary to give some attention to the kind of enquiries one takes to the library, and to the nature of the sources of information available.

Jan 1, 1938