Search Documents

By F. R. Erick Mulder

"AbstractTwo bottom-hole samples have been taken from two new completions in the Turner Valley field, Royalite Lowery No. 8 on the west flank and Royalite No. 73, which was deepened into a lower fault block, on the northeast flank. From the bottom-hole oil of Royalite Lowary No. 8 a synthetic sample was prepared to simulate the original fluid in the reservoir, saturated at the gas-oil contact conditions. The sample from Royalite Lewery No. 8 has been shown to be the original fluid present at this well and represents the oil phase near the oil-water contact in• the reservoir. Complete chemical analysis, P.V.T., and viscosity data have been obtained on these reservoir fluids, which represent the range of saturation from the gas-oil to the oil-water contact in the Turner Valley oil structures. Sampling techniques and the application of the analytical data to reservoir conditions and field operations are discussed. Super-compressibility curves for an average separator tail gas have also been prepared. These data have not been available before. They will be of fundamental value in futu.re reservoir engineering studies of this field and will also serve as a guide in determining operating practices."

Jan 1, 1950

By Karl J. C. Harries

"7.1. INTRODUCTIONThis chapter addresses the joint venture and examines a number of general concepts of the joint venture relationship. Chapter 8 looks at some specific concepts related to the provisions of a joint venture agreement, which are equally applicable to a shareholders’ agreement or other contractual relationship. The term “joint venture” is used because the author is a common law solicitor (a matter of convenience for which apologies are offered to civil law readers), but it should be noted that, in many aspects, the legal structure of an entity is irrelevant. It is the relationship of the parties, be they venturers or shareholders, that is important, and the areas of concern are surprisingly similar (except for terminology).The details of the joint venture relationship and agreement could fill several books. Accordingly, this chapter and the next focus on selected topics that appear to have caused problems or confusion or to be the basis for disputes. And remember that, although the following discussion is in the context of a joint venture, many of the comments apply, either directly or indirectly, to virtually any common undertaking and the agreement defining it.For interest’s sake, this chapter starts with a summary of some of the earlier types of agreements and arrangements that have evolved into the joint venture agreement of today in Canada, the philosophy of their format, and the reasons for their demise.7.2. EVOLUTION OF THE CANADIAN JOINT VENTUREThe Early DaysMuch of the opening up of Canada’s north is due to exploration for and development of mines. The early discoverers were relatively free to roam and explore at will and, if they were fortunate enough to find something, they dealt with the appropriate government to acquire exploitation rights. The early interests lay in gold or silver. Workings were small, usually worked by the owner alone or with only a couple of helpers to extract the native gold or silver. If the owner wanted to move on, he could sell his property outright and use his stake to look elsewhere.As logging and mining camps were opened, the development of better roads and railways made access easier. Entrepreneurs saw the opportunity to make money by assembling large parcels of land and working them as a single operation. In order to do this, some owners who were not ready to sell out had to be convinced to do so through more attractive offers"

Jan 1, 2003

By J. P. Nicoud

"The Frog's Leg project is located in the Kundana mining centre 22 kms West of Kalgoorlie, in Western Australia. The Mines and Resources Australia (MRA) Dioro Exploration Joint Venture has had considerable exploration success centred on the high grade Frog's Leg discovery. A gold resource of 930,000 ounces has been defined. At Frog's Leg there have been three discrete resource domains recognised - Supergene, Contact, and Quartz Lodes. This paper describes the metallurgical test work undertaken.The selection of the drill core was a joint effort by the MRA Senior Geologist and Mineral Engineering Technical Services (METS) to ensure the samples were representative of the ore body. Optimisation of gold recovery was essential as both the Contact and Quartz Lodes have exceptionally high percentages of free gold as well as significantly higher grades than the typical open pit ores found in Western Australia. The metallurgical scope of work included documenting all of the metallurgical test results, establishing the comminution characteristics, determining the percentage of gravity recoverable gold, evaluating the cyanide leach characteristics and determining the tailings characteristics. These studies were used as the basis of flow sheet design to treat both ores and to discuss the advantages and disadvantages of alternative flowsheets. Investigations also included toll milling options at various plants as well as second hand and transportable plants. Considerable technical effort has been put into ore characterisation by way of test work aimed at managing the process risk at each stage of project development, including mitigation. MRA also carried out detailed mineralogical analysis of the ores."

Jan 1, 2005

By Dirige. A. P. E.

A study was conducted for an operating mine to determine the appropriateness of its tailings material to be used for the preparation of a low modulus, high density backfill. The research was initiated due to issues arising from increased observations of compressive failure of backfill placed in stopes and inconsistent backfill behaviour (i.e. increased backfill brittleness and modulus). Backfill materials investigated were classified tailings and de-slimed tailings. Characterization of the physical properties of the classified and de-slimed tailings materials was conducted to assess the effect that these material properties would have on the strength and deformation behaviour of high density backfill products made using them. Such behaviour was investigated to determine whether differences in tailings physical properties would influence the strength and modulus character of the backfill materials. Uniaxial (UCS) and consolidated-undrained triaxial compression strength tests were conducted to determine strength performance and deformation behaviour of backfill. This paper presents the results of the backfill material characterization study and how different particle size distributions affected the strength performance and deformation behaviour of the different backfill mixes. It also demonstrates how stress-strain curves generated from material strength tests were used to evaluate variation in high density backfill mix response when such materials were subjected to unconfined and confined (triaxial) compression loading.

Aug 1, 2013

Abstract - A method to extract certain types of error variance information from paired data is presented, which constitutes an important tool for the calibration of Gy’s formula for variance predictions in the sampling of broken ores. The research summarized here complements publications by others on geochemical precision. The model and method proposed for treating duplicate data provide a practical means of deriving separate estimates of the purely analytical and aliquot sampling variances, from a unique set of duplicate assays, and, hence, proposes a new avenue for estimating effective mineral grain size.

Jan 1, 1998

"The Companion Policy is guidance and not law. It sets out the views of the Canadian Securities Administrators (CSA) at to the manner in which the CSA interprets and applies certain provisions of NI 43-101 and Form 43101F1. The Companion Policy references the CIM Best Practice Guidelines for Mineral Exploration, and the Mineral Resources and Mineral Reserves, and that they should be followed by Qualified Persons.COMPANION POLICY 43-101CP TO NATIONAL INSTRUMENT 43-101 STANDARDS OF DISCLOSURE FOR MINERAL PROJECTS This companion policy sets out the views of the Canadian Securities Administrators (the “CSA”) as to the manner in which the CSA interprets and applies certain provisions of National Instrument 43-101 and Form 43-101F1 (the “Instrument”), and how the securities regulatory authorities or regulators (the “Securities Regulatory Authorities”) may exercise their discretion in respect of certain applications for exemption from provisions of the Instrument. PART 1 APPLICATION AND TERMINOLOGY 1.1 Supplements Other Requirements – The Instrument supplements other continuous disclosure requirements of securities legislation that apply to reporting issuers in all business sectors. 1.2 Evolving Industry Standards and Modifications to the Instrument- Mining industry practice and professional standards are evolving in Canada and internationally. The Securities Regulatory Authorities will monitor developments in these fields and will solicit and consider recommendations from their staff and external advisers as to whether modifications to the Instrument are appropriate. 1.3 Application of the Instrument -The definition of “disclosure” under the Instrument includes oral and written disclosure. The Instrument establishes standards for disclosure of scientific and technical information regarding mineral projects and requires that the disclosure be based on a technical report or other information prepared byor under the supervision of a qualified person. The Instrument does not apply to disclosure concerning petroleum, natural gas, bituminous sands or shales, groundwater, coal bed methane or other substances that do not fall within the meaning of the term “mineral project” in section 1.1 of the Instrument. 1.4 Mineral Resources and Mineral Reserves Definitions - The Instrument incorporates by reference the definitions and categories of mineral resources and mineral reserves as set out in the Canadian Institute of Mining, Metallurgy and Petroleum (the “CIM”) Definition Standards on Mineral Resources and Mineral Reserves (the “CIM Definition Standards”) adopted by the CIM Council on November 14, 2004, as amended. 1.5 Best Practices Guidelines for Mineral Resources and Mineral Reserves - A qualified person classifying a mineral deposit as a mineral resource or mineral reserve should follow the CIM Estimation of Mineral Resources and Mineral Reserves Best Practice Guidelines adopted by CIM on November 23, 2003, as amended. These guidelines are posted on www.cim.org."

Jan 1, 2003

By A. Tabereaux

The reduction of perfluorocarbon (PFC) emissions from aluminum electrolytic cells is a key issue in reducing greenhouse gases at all aluminum smelters, The emission of tetrafluoromethane (CF4) and hexafluoroethane (C2F6) gases during anode effects at smelters can be calculated using two different methods; anode effect-minutes slope and anode effect overvoltage, This work demonstrates that the optimum method depends to a large extent on the type of anode effect kill algorithm utilized at each smelter, CF4 emissions vary widely from aluminum cells depending on the type of anode effect kill method utilized; fast, aggressive anode bridge movements vs. slower, moderate anode bridge movements.

Jan 1, 2005

By Karl J. C. Harries

"6.1. INTRODUCTIONThis chapter comments on some of the more common types of agreements related to property examination and acquisition, other than the farm-in/joint venture agreement or common undertaking, which is dealt with in the next two chapters. Many of the comments made in Part IV of Chapter 4 apply equally to any such agreement. In addition, many of the comments in Chapter 8 and the examples in Volume II are most certainly relevant to many other types of agreement.6.2. RIGHTS OF FIRST REFUSAL1A right of first refusal is a right that obligates an owner to offer his property, or an interest therein, to the holder of the first right if the owner intends to sell or otherwise dispose of it. It may be triggered either by the owner wishing to offer his property for sale or by receipt of a bona fide offer to purchase his interest from an “outside” third party. The mechanics and procedures to implement a first right should be set out clearly in the agreement, and their basics are the same, whether the first right is a stand-alone document or is part of an acquisition agreement.2Rights of first refusal are common in agreements to permit some control over the disposition of an interest and there they can be a valuable provision. However, some explorationists feel that they are also a good stand-alone agreement to have while a property is being evaluated to decide whether or not it is worth optioning. The reasoning is that such an arrangement will tie up the property to allow a quick look and, if the property looks interesting, the balance of the term of the first right will give an ample exclusive period of time to negotiate with the owner and settle an acquisition agreement. In addition, the explorationist is protected by the first right if the owner decides to negotiate a deal with another party."

Jan 1, 2003

By Denni Hoffmann

"Banded iron formation rocks associated with massive sulfide lenses in the Broken Hill Pb-Zn-Cu-Ag deposit in the Namaqualand Metamorphic Complex, South Africa, were investigated with respect to the geochemistry of manganiferous silicate-rich bands. Two common varieties of these are: amphibole- and garnet-rich iron formation bands. The results reveal that the former are enriched in Fe, Mg, Cu, Co and S. The garnet-rich bands are enriched in Mn, Ca, P, Pb and Ba with significant detrital contamination of Ti, AI, Zr, Cr, Y, V, Ni and Nd.The silicate-rich bands have compositions, in terms of, Si/AI, SilFe, FelMn, LalCe and Co/Zn, comparable to submarine chemical sediments which precipitated from hydrothermal fluids. The garnetand amphibole-rich bands are interpreted as ""evolved"" and ""immature"" hydrothermal sediments, respectively. The latter resulted from rapid precipitation after exhalation, whereas the former had a longer residence within sea water. The silicate-rich bands both exhibit increasing Mn/(Mn+Fe) fractions, which are consistent with a variation expected from proximal to distal depositional settings. The prevalence of garnet-rich bands over amphibole-rich bands is interpreted as the result of injection of hydrothermal fluids from a single vent situated along the northwest margin of the Broken Hill deposit."

Jan 1, 1994

By G. F. Trainor

At the Canadian Natural Resources Limited (CNRL) Horizon Mine they use Wenco International Mining Systems Ltd (Wenco) Fleet Management System to monitor and control their production fleet with the goal of increasing operator productivity and safety, and raising dispatcher awareness and control. Amongst the broad productivity goals CNRL wanted to achieve with help from the system was a very specific need to blend ore at the truck level. CNRL uses 25m x 25m block geological model information to represent their complex ore body. Wenco's High Precision GPS application, BenchManager provides precise graphical actual-vs-design operator feedback and system integration. Together the two companies advanced the BenchManager product to meet CNRL's needs by using live camera feeds to compare activity with data collection that ultimately lead to changes in the algorithm to include enhanced GPS indicators and the support of a GLONASS assisted solution generating distance and bearing information.

May 1, 2011

By C. Greimel

Modern roadheaders provide a safe and cost-effective, yet very flexible way of mechanical tunnel and roadway excavation. In the last years, SANDVIK Mining and Construction has developed a NEW ROADHEADER GENERATION, which incorporates new features, allowing significant improvements of underground excavation. Partial face cutting machines such as roadheaders excavate the desired profile by means of a cutter unit mounted on a swiveling boom. This flexible method for mechanical excavation makes the roadheader suitable for a large range of profile varieties and most rock characteristics. Over 1,250 roadheaders have been delivered since the 1960s from the Zeltweg plant of Sandvik Mining and Construction, with the current products ranging from the light-duty, 130kW MR220 machine, widely used in the tunneling and coal industry to the heaviest 300kW tunneling and hardrock mining roadheaders. Roadheaders are generally used in coal mine development, salt/potash mining as well as construction and hard rock mining. This paper describes the technology behind the succesful introduction of hard rock cutting with roadheaders, and aims to offer best practise operation experiences from various hard rock cutting sites.

Oct 1, 2010

By R. Dawes, B. R. Davis, T. LeBel, C. Pelow

Settling of copper, lead, and other metals in slags is an important part of overall recovery of metals, both in primary and secondary operations. The impact of slag reduction on settling is not well known. This is important since the cycle time for slag cleaning can be significantly changed with reduction of slag, through a decrease in slag viscosity and growth of metal/sulphide particles. KPM has worked with a number of primary and secondary recyclers to better understand how reduction of slag can improve overall operation. In this presentation, we describe the type of test work and analysis done and how this information can be used to guide improvements in metal recovery from slags. INTRODUCTION Typically, copper smelter slags contain about 1-2% copper, both in the form of copper and copper sulphide beads and dissolved copper oxide in the slag (converter slags are recycled to the smelter). With the average grade of world copper deposits close to 0.7%, it is practical to recovery copper from these slags. This is done routinely by one of two methods. The first method uses slow cooling in large ladles or beds to grow particles of copper sulphide. The slag is then crushed, milled, and floated for copper recovery. The slow cooling promotes precipitation and growing of the sulphide particles from the solution and then, the slag can then be milled to recover the copper through froth flotation. A consideration of this process includes the energy cost related to grinding, the use of water, capital cost for ladles, and the availability of tailing dumps. At the same time, the retreatment of the Cu concentrate produced in the mill will displace fresh concentrate, which ultimately results in a reduction of the throughput. The second method is the so-called “slag cleaning” and is based on the settling of copper and copper sulphides particles dispersed in the slag. This is achieved by decreasing its viscosity by increasing the slag temperature and reducing the iron spinel solid phases (magnetite) that increase the apparent viscosity of the slag. Typically, the reduction does not extend to the reduction of copper, and soluble copper (mainly as oxide) and fine matte particles remain at concentrations typically at or above 0.5% (Cardona et al., 2011; Cardona, 2011). This is an improvement on 20 years ago when slag was sent to dumps at 1% or less (Demetrio et al., 2000).

Jan 1, 2019

By L. Chunpongtong

ABSTRACT Oil sands production occurs on a massive scale, making orebody estimation a challenge. In rainy conditions, operators can have difficulty accessing ore at the mapped location. Without enough inventory as a buffer, the high-cost stockpile is depleted quickly, necessitating the removal of significant amounts of overburden and interburden to meet plant feed requirements. The inventory curve—a plot of ore inventory on a period-by-period basis—plays an important role in selecting an appropriate scheduling scenario. This paper presents a programmable method for creating an inventory definition by using a pit optimization tool.

Jan 1, 2014

By A. P. E. Dirige

The stability design of cemented backfills is normally conducted using conventional approaches. Analytical or numerical models, backed by trial-and-error methods, are the primary means used to describe or predict the support performance of backfills during mining. The stability of paste backfill free-standing faces is a major concern due to potential consequences to production, ore dilution and safety. Available analytical or mathematical models are developed based on assumptions of the failure modes that may occur when vertical fill faces are exposed during adjacent mining. Numerical modeling serves to provide an understanding of backfill strength and deformation behaviour. Such approaches offer inherent limitations and generally result in conservative designs. In this paper, centrifuge physical modeling was conducted not only for performance evaluation studies, including stability analysis, but to develop an understanding of the strength and deformation behaviour of paste backfill exposed faces when the adjacent ore zone is removed. The failure mode and mechanics of failure observed in the centrifuge model of a given prototype situation are discussed in detail. Centrifuge model results were compared to numerical modeling and it was concluded that a sliding block failure mechanism that resembles a circular slip appears to be the predominant failure mode.

Aug 1, 2013

By C. Schlumberger

INTRODUCTION The object of the present paper is to discuss, from a geological point of view, the practical results obtained by the authors with the method of the 'resistivity map of the subsoil' in the study of various mining problems. Some of the studies described date from 1920, 1922, and 1923. They are, therefore, quite old, at least as far as geophysical research is concerned (1). Others, on the contrary, are very recent (2). We shall deal only very briefly with the theoretical and technical sides of the processes employed. This paper has, essentially, a practical purpose, and it has seemed unnecessary to enter into a detailed discussion of the methods. Such a discussion cannot be presented without introducing ,quite. Complex considerations both of mathematics and experimental physics, which interest only the geophysicist: whose work is highly specialized.

Jan 1, 1931

By O. Benavente, M. C. Hernández

Selenium is obtained mainly from copper anode slimes, which is a by-product of the copper electrorefining process. Selenium is present in copper anode slimes as silver and copper selenides. Traditionally, selenium has been obtained by pyrometallurgical processes; however, hydrometallurgy has now been incorporated either full or partial to the conventional process. Some hydrometallurgical processes are been developed and used at laboratory level an industrial scale. This document describes theoretical background and results of characterization and dissolution of selenium from a decopperized anode slimes in an alkaline oxidizing system. The results have indicated that the oxidizing leaching process reaches a practically complete dissolution of selenium (up to 90 %); the undissolved portion is due to the generation of a AgCl around the particle surfaces that delays the progression of the reaction. The results indicated that 90% of selenium extraction can be obtained by dissolution under moderate conditions of pH, temperature and reagent concentration in oxidizing medium. INTRODUCTION Selenium is distributed in the earth's crust in most rocks and soils. Selenium is essential, as it has wide range of applications in the medical and food industries as well as, used in semiconductor, sensors and photochemical devices. Selenium is rarely found in the native state, 90% of selenium is obtained from copper anode slimes, which is a byproduct of the copper electrorefining process (Lu, Chang, Yang, & Xie, 2015; Xiao et al., 2017; Yang et al., 2018). In anode slimes, selenium is present as an intermetallic compound, as Ag-Cu selenides. Currently, selenium is recovered from the anode slimes via hydrometallurgical and pyrometallurgical processes (Lu et al., 2015). The traditional pyrometallurgical method recovers selenium effectively, but faces difficulty as a result of increased energy costs and strict environmental regulations associated with the process (Li, Yang, Jin, Chen, & Tong, 2017). Therefore, hydrometallurgical processes are proposed in oxidizing medium such as nitric acid, alkaline leaching with sodium nitrate, wet chlorination and pressure leaching, amongst others (Hait, Jana, & Sanyal, 2012; Kim & Wang, 2010; Xiao et al., 2017; Yang et al., 2018).

Jan 1, 2019

By H. Y. Sun, Q. Y. Tan, X. P. Niu, L. Li, Y. Jia, R. M. Ruan

During bioleaching processes of sulfide minerals, the sulfide minerals act as the natural habitats for acidophiles, of which, most are autotrophic iron and sulfur oxidizing microbes. These microbes acquire energy by oxidation of sulfide minerals, and play crucial role in bioleaching processes. In the industrial bioleaching heaps, microbial community and their activity are highly related to engineering configurations, while the optimized industrial operation can help to fast dissolution of aim minerals and acid/iron balance under optimized microbial condition. Microbial community succession and activity formation, the function of microbes to mineral dissolution, the mechanisms to promotion and inhibition of sulfide minerals oxidation, and the industrial instances for microbial community regulation were reviewed. For these instances, promoted microbial activity helped to fast pyrite oxidation for sulfuric acid generation, which realized zero sulfur acid addition to the irrigation solution in the initiation of a bioleaching heaps. High microbial activity by optimized operation parameters improved Cu leaching efficiency during the heap bioleaching process. And also by inhibition of microbial activity, especially the iron oxidizing microbes, the excessive pyrite oxidation can be inhibited, which helped to the acid/iron balance during heap bioleaching. INTRODUCTION Around the world, high grade copper ore are exploited, while barely new high-grade deposits are succeeded, the copper grade of ore deposit is constantly decreasing. The increasing copper demands worldwide requests to process these low-grade ore deposits. Processing of low-grade ores are not economical by usual extraction processes. Heap leaching is a cheaper process for recovery of low-grade ores, and has been applied to extract valuable metals from sulfide minerals worldwide, such as copper, gold, uranium and nickel (Gericke et al., 2009). Heap leaching process has greatly decreased the economic grade and expanded the recoverable ore reserve worldwide (Brierley, 2008). It is usually carried out in the open environments, and could process huge amount of ore (usually in millions of tonnes in one reactor) in the heap reactor (Gericke et al., 2009). For copper sulfide, especially the secondary copper sulfides, heap (dump) bioleaching is successfully applied. Heap bioleaching process is cost saving, and sometimes can be achieved without adding chemical into heaps, by microbial fixing of the atmospheric N2 and CO2, and generating oxidant Fe3+ and sulfuric acid in heaps from oxidation of sulfide minerals. Also heap bioleaching is environment friendly by cycling use of the leaching solution, and without exhaust emission.

Jan 1, 2019

By A. Ignatieff

"THE WORLD'S coal resources represent the largest component of non-renewable energy resources. Coal is now regaining Its position following a temporary decline, particularly in North America during a period of about a quarter of a century. This period provided the opportunity to improve both surface and underground mechanization, thereby increasing the productivity and improving conditions for humans in the mines. Similarly, in preparation, improved cleaning of coal from various impurities including sulphur was achieved, to meet the more demanding requirements for coking coal. Progress was also made in combustion, particularly related to the reduction of pollution. Canada participated in most of these developments, despite the country's strong commitment of the use of hydrocarbons during this period. _Bearing in mind the vastness of this land (3.85 million sq. miles) by comparison with countries like U.S.A., U.S.S.R., and China, Canada's coal resources estimated to date are not large and they are scattered. The original evaluation of 1913 estimated the ""reserves"" from seams over one foot in thickness and a limiting depth of 4,000 ft at 1.2 trillion metric tons. D:. ~.R. MacKay, in his evaluation for the 1946 Royal Commission on the coal industry, known as the Carroll Commission, reduced the ""reserves"" to 99 billion short tons. The increased knowledge now available would indicate that the 1913 estimated was too liberal and the 1946 estimate too conservative but both were closer to a resource than to a reserve designation. Some adjustments of Dr. MacKay's estimates were made in 1970 by B.A. Latour of the Geological Survey of Canada and L.P. Chrismas of Energy, Mines and Resources Canada (EMR). In the last decade the Alberta Energy Resources Conservation Board has developed its own methods of evaluating coal resources and reserves. A methodical approach of exploration and evaluation was carried out by Saskatchewan jointly with the federal government of the lignite resources of Southern Saskatchewan. A similar joint program is in progress in Nova Scotia. Meanwhile, the industry itself carried on an extensive exploration program on the outcrops of promising projects in the Inner Foothills belt of Alberta and British Columbia in preparation for surface mining on a very large scale, with some development of hydraulic mines. All these activities have been reflected in the increase of the country's resources and reserves, which now fortunately are separately defined. In 1979 EMR issued Report E.R. 79/9(1>; the data were developed in 1978 and provided to the World Energy Conference Organization<2>. In 1980 the World Coal Study (Wocol), an international group that included Canada carried out a study which updated the W.E.C. data, indicating some reduction of the 1978 figures; quantities were reported in million metric tons of coal equivalent (C.E.)*(Jl."

Jan 1, 1985

By Marc C. Bétournay

Replacing diesel power in underground metal mining vehicles with available clean energy (e.g. hydrogen, lithium-ion batteries) is now a priority due to worker health issues, the increasing price of diesel, ventilation costs and air quality. Hydrogen fuel cells are a known and broadly applied power technology. They have been the focus of a dedicated research program to carry our proof of concept projects as well as regulatory developments for mining application. However, hydrogen remains a demanding energy vector to use in confined, underground applications. Standardization and safety considerations are being addressed in the industrial consortium Hydrogen Mine Introduction Initiative (HMII). Research projects are being carried out to resolve the gaps for regulated use. This article focuses on HMII objectives and Project results. The first has reviewed the relevant codes and standards and mine regulations, indicating that hydrogen and fuel cells could be allowed underground and that current codes, especially the Canadian Hydrogen Installation Code would be sufficient for hydrogen use. The second project established the standard hydrogen storage and distribution architecture along with related risks and safety requirements for its use in the third project, using an underground test chamber to delineate the behaviour of hydrogen leaks in confined conditions with various ventilation regimes and ignition studies. This project will end in 2013. It will be followed by the last project, which will establish best practices in support of regulations development, and develop the ISO standard for mine hydrogen infrastructure and underground application.

Aug 1, 2013

By P. K. Kaiser, D. D. Tannant

"A support system for large ground convergence conditions or burst-prone ground must contain holding elements (rockbolts, cable bolts, etc.) that are strong yet capable of sustaining large deformations, i.e., they must absorb as much energy as possible. Steel wire rope anchored in a borehole by a friction bolt provides these desired yield characteristics if the frictional anchorage is placed deep enough into the rockmass, i.e., in non-yielding rock or beyond the expected depth of rock ejected during a rockburst. Pull-out tests were conducted on wire ropes anchored by inflated Swellex bolts to assess the feasibility of this support concept. The test results demonstrate that a Swellex bolt generates a frictional anchorage that allows the wire rope to slide at high loads and to absorb significantly more energy than either a Swellex bolt alone, or a cement-grouted cable.The rope/friction bolt combination can be engineered to provide the desired energy absorption and allowable deformation by varying the installed lengths of the friction bolt and the rope. For yielding rope support, the contact length between the rope and Swellex bolt must be short enough to ensure that the rope can slip well before its tensile capacity is reached. A safe maximum overlap length is about one metre for the wire rope used in this testing. When used as support in the backs of drifts, a swaged button on the ropes end must be used to ultimately mobilize the full rope capacity thereby protecting against gravity-driven falls of ground."

Jan 1, 1995