Search Documents

By A. Iizuka

This study was aimed at separating and recovering arsenic, antimony, and tin from refining byproducts generated in a nonferrous smelter. The target byproduct was a silicate slag containing the above elements. The silicate structure of the slag was destroyed by alkali roasting, which then enabled leaching of arsenic, antimony and tin in solution effectively. Arsenic was selectively leached out by hot water after alkali roasting of the slag, while remained antimony and tin in the residue were leached out by a hot hydrochloric acid solution. However, when the solid-liquid ratio in the leaching solution was increased, hydrous gelatinous silica (gel-like silica) was formed during the hydrochloric acid treatment and filtration became difficult. Therefore, high temperature and high pressure leaching was attempted to improve the filterability of the silica leaching residue. In the high temperature and high pressure treatment, the hydrous gel-like silica was transformed into easily filterable aggregated silica, and thus, filtration became easy. By investigating the neutralization and sulfurization treatment for the obtained hydrochloric acid leachate (second leachate), it was possible to separate antimony and tin. INTRODUCTION This study aims to separate arsenic and recover valuable metals such as antimony and tin from refining byproducts generated in a nonferrous smelter. The target smelting byproduct is antimony-containing slag in this study. In many cases, alkali roasting was adopted as pretreatment for extraction and recovering valuable metals from smelting residues and wastes (Rao, 2006). For antimony-containing slag in this study, one effective method for separating arsenic is to convert arsenic to sodium arsenate (Na3AsO4) by roasting with a sodium compound and then to remove arsenic by hot water leaching. In addition, by alkali roasting, the silicate structure of the slag is destroyed, and effectively alkalizing tin and antimony is accomplished. Then, precipitating and recovering tin and antimony leached into the acid solution are considered possible by sulfurization and neutralization treatments. In this research, we conducted basic studies on the following. 1) Destruction of silicate structure in slag by alkali roasting and leachability of arsenic. 2) Conversion of hydrous gelatinous silica to aggregated silica by hydrochloric acid treatment of residues after arsenic leaching under high temperature and high pressure, as well as leachability of antimony and tin. 3) Separation and recovery of antimony and tin by sulfurization and neutralization treatments of hydrochloric acid leachate. These topics of investigation can support to consider the separation and recovery process of arsenic, antimony, and tin from antimony containing slag.

Jan 1, 2019

By C. J. Edmonds

Of the gold mined in Canada over 90 percent is extracted from the ore by the process of "cyanidation". In this process crushed ore is treated with lime to provide "protective alkalinity" and cyanide, usually in the form of sodium cyanide. The gold is dissolved in the cyanide solution, which after further treatments for clarification, is precipitated by the addition of zinc dust. Wastes from the process consist of tailings which will contain cyanides. Water consumption, mill size, effluent quantity and quality are depicted in transparency (1). It should be noted that as far as the wastes are concerned it has been impossible to postulate a typical situation. Variation from the above data will occur. A summary of data from tailings pond effluents is presented in transparency (2). The figures in parentheses indicate the usual range of values for the parameter.

Jan 1, 1973

By A. Pranowo, G. R. F. Alvear F., N. Aslin, M. S. Moats

"The toxicity of arsenic is well known and documented; however, the presence of arsenic in copper electrorefining anodes and electrolytes is critically necessary to produce high-quality cathode. Arsenic as well as antimony and bismuth concentrations vary relative to their concentration in the anode copper received from the smelter. The behaviour and benefits of arsenic in copper electrorefining and the detrimental effects of antimony and bismuth on cathode quality and tankhouse performance are discussed. This will include the minimization and mitigation of problems associated with arsenic, antimony, and bismuth—including cathode contamination, floating slimes, scaling, and anode passivation.RÉSUMÉ La toxicité de l’arsenic est bien connue et documentée; toutefois, la présence d’arsenic dans les anodes de l’électroaffinage du cuivre et dans les électrolytes est d’une nécessité critique pour produire une cathode de grande qualité. Les concentrations en arsenic, ainsi qu’en antimoine et en bismuth varient selon leur concentration dans l’anode de cuivre reçue de la fonderie. Le comportement et les avantages de l’arsenic dans l’électroaffinage du cuivre et les effets indésirables de l’antimoine et du bismuth sur la qualité de la cathode et le rendement des cuves d’électrolyse sont discutés. On traite aussi de la minimisation et de l’atténuation des problèmes associés à l’arsenic, l’antimoine et le bismuth – incluant la contamination de la cathode, les schlamms flottants, l’entartage et la passivation de l’anode."

Jan 1, 2016

By Eiichi Sato, Koichi Kitazono, Hiroshi Masuda, Kenta Higane

"The present study investigated the low-temperature creep mechanisms in ultrafine-grained (UFG) aluminum manufactured by accumulative roll bonding. UFG aluminum with grain size 0.39 µm showed steady state creep even at room temperature under low stresses as confirmed by the creep curves in the strain rate–strain plot. The low-temperature behavior was divided into four regions by three distinctive stresses, sI, sII and sIII: sI (=45 MPa) is denoted as the micro-yielding stress with which dislocations start movement, sII (=85 MPa) the dislocation-multiplication stress above which dislocations multiply with creep deformation, and sIII (=171 MPa) the conventional yield stress above which macroscopic plastic strain is generated. During low-temperature creep, below sI, negligible plastic strain is generated. Between sI and sII, creep deformation with stress exponent 2.5 occurred, which is accommodated by dislocation absorption into grain boundary and grain boundary sliding, similarly to the low-temperature creep of HCP metals. Between sII and sIII, creep deformation with stress exponent 7.0 occurred, whose mechanism is similar to the low-temperature creep of coarse-grained aluminum. Above sIII, power-law breakdown occurred.INTRODUCTIONIt is well understood that the creep deformation brings about at high homologous temperatures (T/Tm) of >0.4, where Tmis the melting point, with diffusion processes. Recently, the importance of aluminum is increasing for cryogenic temperature parts such as a metallic liner or a cap in high pressure-hydrogen vessels, and the presence of creep behavior in aluminum at room temperature has become recognized (Matsunaga, 2013;Kassner, 2015).In HCP metals and alloys, especially intitanium, steady-state creep behavior appears at room temperature with apparent activation energy of1/10 of that for self-diffusion(Neeraj, 2000; Matsunaga, 2009).On the other hand, Kassner (2015) claims that aluminum shows creep behavior at room temperature with apparent activation energy of 4/5of that forself-diffusion, but never reaches the steady state. We should note that it is derived from the data obtained from short-term creep tests of few hour, and Matsunaga (2013) already claimed the presence of steady state in room temperature creep in aluminum with activation energy of 1/5of that for self-diffusion.The mechanisms for low temperature creep are considered different between HCP and FCC metals: in HCP metals, grain boundary sliding is observed and is thought to accommodate piled-up dislocations at grain boundaries through absorbing them. The so-called slip-induced grain boundary sliding occurs with low number of activated slip systems(Matsunaga,2009).On the other hand, in FCC metals, many activated slip systems bring about work hardening with dislocation cell structure formation. In the initial stage of creep, it results in primary creep (Kassner, 2015), but Matsunaga (2013) claimed that once the annihilating of a cross-slipped dislocation to another reaches balance, steady state is established. It has been, however, strongly required to show more convincing experimental verification for the presence of steady state in FCC metals at low temperature."

Jan 1, 2018

By X. X. Wu, Q. Zhang, R. H. Fan, Y. J. Feng, J. D. Liu, P. Z. Zhao

In the present study, AA6016 automotive sheets with different grain size were fabricated through changing fabricating parameters, and the effects of grain size on the bendability were studied by bending test and optical microscopy. The results showed that the sheet with coarse grains exhibited poor bendability, and some micro-cracks were revealed at the surface of the bending samples. While the sheet with fine grains exhibited good bendability, and the bending samples showed smooth surface. Shear bands on the cross section of bending samples were observed. It was found that samples with coarse grains had more shear bands. These shear bands distributed in bundles, which facilitated the formation of continuous neckings and micro-cracks. However samples with fine grains had less shear bands, which distributed uniformly. The decrease of grain size could not only hinder the formation of shear bands, but also improve the homogeneity of its distribution during bending. On the other hand, refining grains could increase the amount of grain boundaries, which impede the propagation of shear bands. Hence the decrease of grain size could hinder the formation of continuous neckings and micro-cracks during bending, resulting in the significant improvement of the bendability.

Jan 1, 2015

By Xuanxue Mo, Kaihui Yang, Steven D. Scott

Abstract -The Changning-Menglian metallogenic belt in western Yunnan, China, is characterized by the occurrences of both Pb-Zn-Cu and Cu massive sulfides in Permo-Carboniferous mafic volcanic sequences. These deposits were formed in a back-arc basin at a rifted continental margin in the Paleozoic Tethys Ocean. Pb-Zn-Cu deposits are associated with alkalic basalt, andesite, and lesser felsic volcanic rocks intercalated with limestone, which probably formed along an immature rifting segment on a continental basement. These volcanic rocks are enriched in K, Ti, LREE, and other incompatible elements, and have the attributes of alkalic within-plate basalt. An extensive unit of sulfide- carbonate-silica shale in proximity to massive sulfides contains high values of Mn, As, Mo, W, Sn, Sb, and Hg, and has REE patterns that are similar to the volcanic rocks. This, together with the graded bedding in the footwall volcanic rocks, suggests that the sulfides precipitated in a shallow, unstable, and carbonate-saturated volcanic basin. A stringer zone is traced downward for 500 m below the massive sulfide orebodies. It is characterized by an upper sericite-quartz zone and an extensive lower skarn alteration with enhanced W, Sn, and Bi. Lead isotope data show both continental basement and magmatic sources may have supplied the ore metals. Cu deposit and occurrences are hosted by tholeiitic units that represent the mature spreading segments in the back-arc basin. The tholeiitic lavas have LREE-depleted or flat REE patterns similar to MORB or back-arc mafic lavas. The cupriferous massive sulfides are overlain by an extensive unit of chlorite-magnetite or ochre, suggesting a relatively oxygenated oceanic basin. Ni and less Co mineralization is found in dolomite veins of the stringer zone. Enhanced concentrations of Ni, Co, Au, and As are found in the massive sulfides and in sulfide-rich tuffites. The geological setting and mineralization of the Changning-Menglian belt has similarities with modern back-arc basins such as the Manus Basin in the western Pacific.

Jan 1, 1999

By Lucas van Latum

A Model for Safety Swiss cheese metaphor of safety layers Image »Multiple layers with independent, often transient failure modes »For a loss to occur, all layers must fail independently and simultaneously ??Latent? failures are due to inherent system flaws ??Active? failures are due to unsafe acts

May 1, 2011

By Todd Kennedy, Kurt Tischler

"This paper presents the field experience of Siemens with regard to Gearless Drives in the mining industry … We consider the elapsed production hours of Siemens Gearless Drives to be extensive enough to provide a reliable estimation of availability calculated on the basis of data representing repair time, downtime, and operating time. The users of Siemens Gearless Drives confirm an availability of more than 98% after exclusion of some major issues. The paper addresses all of these major issues of Siemens Gearless Drives, describes successfully applied corrective measures, explains the influences on the design of the drives, and lists the downtimes associated with each of these issues. INTRODUCTIONThe first Siemens Gearless Drive in mining began operation in 1980 and was installed on an iron ore grinding mill. As of September 2011, 40 Siemens Gearless Drives will have accumulated 136,000 machine days of operating time. According to pure rules of statistical analysis, this accumulated operating time may be too low to be used for a sample of field data to provide precise statistical values of availability, however we consider it large enough to provide indicative values of worthwhile consideration. This paper deduces the availability statistics of Siemens Gearless Drives in the mining industry from information received from end users and factors in all major issues that Siemens has experienced with our Gearless Mill drives. This paper does not consider Gearless Drives in other industries such as the cement industry. The cement plants, especially in the northern hemisphere, interrupt production for several months in the winter. This lengthy downtime is used to maintain the complete plant including the mills, their motors and their drives. The mining industry has more stringent and higher production requirements. In the mining industry, production must run 24 hours per day, 365 days a year."

Jan 1, 2012

By AN. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By R. Lanthier, A. Broussaud, J. C. Guillaneau, D. Hodouin

This study presents a method for upgrading the information extracted from the measurements given by the sensors of a pilot grinding circuit. For that purpose raw signals are combined to process models for extracting, through filters, the best information on the process state. Two different filters are used; one is based on steady-state mass balance constraints and the other one uses dynamic mass balance equations allowing for material accumulation in the equipment. The filters are designed and tuned with the help of a grinding circuit dynamic simulator and are then implemented in the pilot plant. Their performances and usefulness are discussed.

Jan 1, 1989

By R. A. Parra, Fuentes, C. Godoy, L. E. Arias, C. A. Toro, M. Marin, E. Balladares, V. Parra, G. Reyes, S. N. Torres, D. Sbarbaro

In this paper, we report on the detection of spectral molecular emission of iron oxide (FeO) and copper oxide (CuxO) emitted by reactions occurring in a laboratory scale flash smelting process of pyrite (FeS2) as well as copper concentrate. The novelty of the technique is that, the molecular spectral emission sensing is achieved by using a low spectral resolution and low sensitive radiometer, enhanced with signal processing and matrix factorization techniques. The method was validated using a highly sensitive spectrometer, with a high spectral resolution; achieving a similar FeO spectral pattern as the one obtained after signal processing techniques over low resolution spectral signals. INTRODUCTION Visible-near infrared (VIS-NIR) spectroscopy is an optical contactless sensing technique commonly used to capture information about the emitted, absorbed, transmitted or scattered radiation in a physical or chemical process, with the presence or absence of an excitation light source such as a laser or a broad spectral band source. These techniques coupled with signal processing and machine learning algorithms, sometimes referred as chemometrics (Pisapia et al., 2018), can be found in processes such as: pharmaceutical (Kandpal et al., 2016); food (Coelho et al., 2016); combustion (Ballester & García-Armingol, 2010); siderurgy (Strakowski et al., 2014) industry, among others. In the extractive copper industry there are several technological developments using optical sensing techniques aimed to retrieve information about copper ore and concentrate mineralogical composition such as X-Ray Fluorescence, Qemscan® (Quantitative Evaluation of Minerals by Scanning Electron Microscopy) and X Ray Diffraction (XRD) analysis, however, because of the manual procedures to analyze the samples with these laboratory instrumentation, only discrete information during a daily based operation can be retrieved, making impossible for the operators to take decisions over the involved processes in real time. The aim of our research work presented here is to contribute with sensing and data analysis procedures based on VIS-NIR spectroscopy for the flash smelting process characterization, particularly in this paper, with the detection of FeO and CuxO molecular emissions in a laboratory scale setup.

Jan 1, 2019

By T. J. Bruce, G. E. Agar, R. Stratton-Crawley

"A technique by which the design of a flotation circuit may be optimized is described and examples of the application of this methodology are given.Three interrelated criteria are defined and the application of these criteria to the selection of the optimum residence time for each stage of a flotation circuit is demonstrated. The criteria are:(1) Add no material to the concentrate that is lower in grade than the feed to that separation stage.(2) Maximize the difference in recovery between the desired mineral and the gangue.(3) Maximize the separation efficiency.Three independent systems were examined experimentally and it was shown that application of any of the criteria yielded similar results.It was demonstrated how the application of rate measurements (Criterion #2) could lead to the selection of a set of optimized times for several stages in a flotation circuit and that these could in turn be used to simulate the results of a locked cycle test. The predictions were checked against the experimental results from a locked cycle test and there was substantial agreement between the predicted and observed results."

Jan 1, 1980

By CIM Mineral Resource

On January 9, 2018, the Canadian Institute of Mining, Metallurgy and Petroleum (CIM) Council formed the CIM Mineral Resources and Mineral Reserves Committee (CIM MRMR Committee), which is a combination of the previous Standing Committee on Reserve Definitions and the Best Practices Committee. As part of its mandate, the CIM MRMR Committee updates guidelines for use by Industry, which include the Uranium Practice Guidelines. The 2024 CIM Uranium Leading Practice Guidelines were adopted by CIM Council on November 22, 2024, and supersedes the 2003 version. The main principles and guidelines relating to preparation of Mineral Resource and Mineral Reserve (MRMR) estimates are provided in the CIM Estimation of Mineral Resources and Mineral Reserves Best Practices Guidelines (MRMR BP Guidelines, as updated from time to time). The MRMR BP Guidelines provide information pertaining to metalliferous and other deposits and many sections are readily applicable to the preparation of MRMR estimates for uranium deposits. However, additional guidance is appropriate for uranium deposits due to the radioactive nature of uranium, and its amenability, in some cases, to in situ recovery (ISR) mining methods.

Nov 1, 2024

By Lloyd H. Yeomans

"This paper will cover recent developments in conveyor applications with specific reference to capacities, bell speeds and distances. It will also discuss certain unique arrangements of horizontal, curved and loop belt systems. In addition, the recent changes in safety factors resulting from new conveyor construction methods will be reviewed.IntroductionConveyor belt systems are currently undergoing dramatic changes. Their use is being extended to providing a viable means for the transportation of bulk material over longer and longer distances.In this paper, a brief account of the historical development' of the belt is outlined, demonstrating how conveyor technology has adapted to changing market demands.Today, energy and environmental requirements are providing what may even be greater challenges. The ability of the belt conveyor to transport material and meet those requirements, places it in the position of replacing many conventional means of bulk material transportation.The paper also outlines some of the progress which has been recently made in this regard and includes a broad approach to the subject of belt design and application.Recent design developments have greatly extended the potential of conveyor belt systems to include applications thought impossible just a few years ago.Graphically illustrating the potential of this new technology IS a belting system currently operating in New Caledonia. Built in 1970, the system has an incredible centre distance of 43,000 ft, or about eight miles.Not to be outdone, the British Coal Board is currently constructing a belt system with a centre distance of 49,000 ft and a speed of 1,650 feet-per-minute. This system is expected to be completed in 1986.These innovative advances contrast dramatically to the conveyor belt's beginnings in the early industrial revolution. Oliver Evans, writing in the 1795 edition of 'Miller's Guide' defined the conveyor belt as a ""broad endless strap of thin pliant leather or canvas, revolving on two pulleys in a case or trough.""Obviously, the conveyor belt has come a long way since those early days."

Jan 1, 1983

By A. N. Kumar

Two fabrication stages in the manufacture of pipelines are identified as causing significant deterioration of the steel plates, namely cold bending and welding. The objectives of this work include quantitative assessment of the degradation of the quality of the steel plate by the loss of fracture toughness, and an estimation of the safe working pressure. The study was conducted on three API grade steels: X42, X46 and X60. After cold bending by the UO technique, various welding technique were employed for joining of the bend plates along the pipe length. A crack-tip opening displacement parameter (CTOD) was used at the onset of initiation and at the first load maxima as the criterion for assessing the toughness degradation under various fabrication stages and regime (such as WZ, HAZ and parent body). In addition, strength, hardness and impact energy values were determined to check the degree of degradation. Microstructural and microfractographic investigation of the fractured samples were also carried out in the scanning electron microscope (SEM). X60 grade steel plate suffers from CTOD toughness loss by around 38 and 55% after welding and cold bending, respectively, for the conditions studied. A combined effect of the two stages results in a loss in toughness by around 70% for the same steel. In X42 grade, the loss in impact energy ranges from 78 to 35 J due to electrical-resistance welding study (ERW). Crack resistance curves are also obtained for the steels to study the crack growth resistance behaviour and to supplement the information on crack initiation behaviour. The orientation of the pearlite banding, as observed on the fracture plane with respect to notch front and applied loading direction appears to have a strong influence on the microvoid-coalescence mechanism of fracture as well as the toughness values. An integrated analysis of the performance of pipelines, considering all these key factors, is discussed.

Jan 1, 2005

By K. Reipas

"Westmin Resources Ltd. operates the 3300 TPD H-W underground copper/zinc mine on Vancouver Island. Ore storage underground is handled in a 6000 tonne coarse ore bin and a 3000 tonne fine ore bin. Both of these bins have experienced significant wear since excavation and construction in 1985. Wear problems have included both deteriorating rock walls as well as worn out steel liners and concrete at the discharge points from the bins. Extensive rehabilitation work was completed in 1993.The basis o/this paper is the rehabilitation work done on the coarse ore bin. The design and installation of ground control measures are discussed. The bin access methods used to allow the work to proceed quickly and safely are also presented. This involved the use of a Tekfoam safety bulkhead to protect workers.IntroductionMine DescriptionThe H-W mine was commissioned in 1985. Mine access is by vertical shaft with most production areas at a depth of about 500 m. Host rocks are composed of andesite and rhyolite. Mine capacity of 3300 tonnes per day is achieved mainly by longhole open stoping methods, complemented by room and pillar mining. Metals recovered from the massive sulphide ore are copper, zinc, gold, and silver. Mineable reserves at January I, 1994 were 9.7 million tonnes."

Jan 1, 1995

By R. Shamsodini, A. Poor Zaeif Doost, H. Haji Amin Shirazi, M. R. Garmsiri

"With columns being installed in rougher section at Miduk Copper Complex, the rougher feed mainly reports to rougher-scavenger cells. To evaluate the efficiency of regrinding circuit, we conducted flotation experiments on samples of the feed and the products of the regrinding circuit. The grade difference of these products at 85% recovery was considered as the efficiency index. Results show that, with weight recovery of the rougher-scavengers the efficiency of the circuit increases. Exclusion of the rougher-scavenger concentrate from the feed to the regrinding circuit, resulted in an increase in the efficiency index from 10.12 to 17.6%.INTRODUCTIONThe flotation circuit at Miduk Copper Complex consists of five flotation columns as roughers and ten mechanical cells as rougher-scavengers. According to design criteria, 75% of the final product was expected to be produced by the rougher columns, while most of the feed consisting of liberated valuable particles is introduced into rougher-scavengers. To liberate locked particles, the rougher-scavengers concentrate is introduced into the regrinding circuit (see Figure 1 below). The regrind mill is in reversed closed circuit with a secondary hydrocyclones cluster, and the cyclone overflow is introduced into three parallel cleaner columns. Cleaners concentrate reports to concentrate thickener and the column tailings is introduced into six mechanical cleaner-scavenger cells. The cleaner-scavengers concentrate reports to the regrind circuit(Figure 1)."

Jan 1, 2012

By J. Poplawski

In mineral processing plants, cyclones typically perform the classification duty prior to the downstream recovery process. Particle size distribution of the cyclone overflow is an important parameter and can be viewed as the product of the comminution process. Too coarse of a product will likely have poorly liberated valuable minerals and make recovery difficult. Too fine of a product may represent a missed opportunity to increase plant throughput and/or also result in low recovery due to poor kinetics. “Near-line” particle size measurement instrumentation has been in place for several decades, its availability and low measurement frequency have typically been inadequate for reliable use in automatic control. CiDRA Minerals Processing has developed a novel and robust technology that provides a highly reliable and low maintenance system for “on-line” measurement of the particle size in the overflow of individual cyclones. The system is based around a wetted sensor design with no moving parts and provides a real-time trend of the desired target grind size parameter. The system does not require sampling and associated sample transfer piping that is prone to plugging, thus avoiding high maintenance requirements. Plant data and benefits realized from the latest installations of the CYCLONEtrac PST will be presented. INTRODUCTION Impact-based real-time hydrocyclone particle size measurement Acoustic impact-based particle size tracking is a unique method for measuring and controlling the particle size in cyclone overflow streams. The implementation of this technology is centered upon a sensor probe that is inserted into the overflow slurry stream via a two-inch (50 mm) hole in the overflow pipe (Figure 1). Particles within the slurry stream impact the surface of the probe generating travelling stress waves within the probe. A sensor converts these travelling stress waves into an electrical signal and proprietary signal processing techniques convert these signals into a particle size measurement that is output every four seconds. The sensor is constantly in contact with many particles in the slurry stream, thus obtaining information from orders of magnitude more particles than traditional sample-based technologies. The sensor has no impact on cyclone performance because it is located downstream of the hydrocyclone and the presence of an air core ensures there is no change in the back pressure seen by the hydrocyclone.

Jan 1, 2019

By Elaine Ellingham, Francis T. Manns

"The Orostar and Scadding were two small gold mines owned and operated by Orofino Resources Limited. Conventional statistical treatment indicates an identical arithmetic mean grade of 0.22 oz/T Au for both mineable reserves. Further, the deposits are both shown to have cut weighted average reserve grade of 0.21 oz/T. Orostar mined out at 0.206 oz/T and Scadding at 0.156 oz/T Au. The combined exploration and development database contained 1394 fire assays, more than enough for statistical confidence in a normal distribution. Therefore this study was initiated to determine, if possible, why the mill head grades were lower than the averages and to experiment with several methods to determine whether a reliable statistical mill head grade estimation method would emerge. Despite the identical reserve grades, distinct differences in the grade distribution histograms are present. By studying the arithmetic and log-normal grade distributions, with some attention to South African practices, this paper reports on those differences which may account for the considerable divergence in the mill head grades. Furthermore, this study casts considerable doubt on the industry standard method of cut weighted averages.The global mill head grades of the two deposits have been derived from the arithmetic average grades by graphic means. This precise method of mill head grade prediction, if applied to complex orebodies, could permit selective grade control and result in direct cost savings by allowing the operator to detect false value stopes, benches or levels and emphasize reliable regions of not only gold mines, but also uranium or base metal deposits."

Jan 1, 1992

By Andrew Bamber

A fast and objective spreadsheet-based model for the financial evaluation of innovative mining and processing strategies such as pre-concentration vs. a conventional base case is presented. The size and grade of the deposit must be chosen, from which a mining rate is selected. Expected operational data for the deposit as well as any mill testwork and results from the pre-concentration testwork are entered as input variables on the sheet, and cost and revenue impacts are calculated in the ?Output? sheet. A capital sum and operating costs for the initial mine and mill development as well as the pre-concentration facility are calculated. The net changes in capital and operating costs are calculated, and impacts on revenue through changes in metal recovery are also calculated. These outputs are used to calculate the overall impact on the cutoff grade and thus the size of the mineral reserve using a generic grade-tonnage model. The NPV and NPV profile of the two scenarios is calculated, with variations in basic parameters such as operating cost, capital requirements, metal price or grade as well as discount rate. Cost and revenue impacts are evaluated and compared to the baseline to establish a positive or negative impact overall. Different scenarios of grade, tonnage, mining rate, process performance, capital and operating cost structure can be explored using the model. Outcomes projected by the model for case studies conducted thus far have been calibrated against internal estimates by the sponsoring organizations and found to be accurate to within 30%, confirming the utility of the model in practice.

Oct 1, 2009