Search Documents

By B. Rivard, D. Francis

A layered Archean magma chamber is exposed at the base of the Yasinski segment of the La Grande greenstone belt. This intrusive complex lies beneath a sequence of mafic volcanics and is underlain by granitoid basement which is crosscut by a swarm of gabbroic dykes. The gabbros of both this complex and the dyke swarm of gabbroic dykes. The gabbros of both this complex and the dyke swarm define a pronounced Fe-enrichment trend. The volcanic patterns of the La Grande and Eas tmain greens tone belts, however, define a series of iron depletion trends which originate in the iron enrichment trend of the gabbroic intrusives. These patterns suggest that the gabbros produced in the intrusive complex may serve as parental liquids for some of the lava suites of the James Bay greens tone belts.

Jan 1, 1984

By Atsushi Sainoki

Blast vibration induced by mining activities, such as stope production blasts, could lead to the initiation of seismic events that inflict damage to mine openings. In this paper, the effect of stope production blasts on nearby fault is examined. First, validation of blast vibration attenuation is performed with a numerical model representing a single blast hole through comparison with that calculated from charge-weight scaling law derived from in-situ data. Subsequently, a mine-wide scale model with a fault parallel to a steeply dipping, tabular ore deposit that is mined out with sublevel stoping method is generated, and the stopes are extracted and backfilled with static analysis to simulate burst-prone conditions on the fault. Based on the stress states, dynamic analysis is performed, in which blast vibration is applied to grid points on a stope wall on the hanging wall side. This assumes 9 blast holes located close to the wall, and blast-induced particle velocities that consider the positional relationships between the assumed blast holes and the stope wall are applied. During the dynamic analysis, blast sequence is considered, and stress states and shear displacement on the faults are examined. It is found from results that, after a rise in normal stress on the fault due to compressive waves induced by the blasts, the normal stress decreases because of the reflection of the compressive waves on the fault. The reduction in the normal stress due to the reflected waves is found to be large enough to cause the fault to slip. The results also show that the level of normal stress eventually keeps decreasing with time as the blast sequence proceeds and that an increase in shear displacement on the fault is accompanied by a decrease in normal stress. This study clarifies the mechanism by which blast vibration causes the fault to slip. In addition, the simulation technique to apply blast vibration that takes into account blast sequence and the locations of blast holes to a stope wall is developed.

Aug 1, 2013

By W. A. Dixon Edwards

Industrial mineral production in Alberta, worth $468 million in 1997, comes from a dozen types of industrial minerals, mined by about 400 producers. Cement and lime from Paleozoic limestone formations exposed along the Rocky Mountains account for the greatest production value. Sand andgravel is the primary source ofmineral aggregate. Almost two-thirds of this aggregate is consumed in the Edmonton and Calgary regions. Sulphur produced at 48 sour gas processing plants and two oil sands plants was valued at $84.8 million in 1997 and accounted for 80% ofCanadian sulphur production. Four companies solution mine the Elk Point salt beds to produce chlor-alkali chemicals, industrial salt and sodium chlorate. Natural brine is also produced as a dust control product. Al $22 million, peat moss is a major industrial mineral product in Alberta. Other minerals with noteworthy production include shale, stone, silica and ammolite. The commodities with the greatest development potential are diamond, silica and oil sands tailings by-product minerals.

Jan 1, 2001

By A. Azizi, P. Blatter, A. Bouajila

ABSTRACT In-situ monitoring of gold dissolution by means of a rotating electrochemical quartzcrystal microbalance unveiled dramatic decreases in gold leaching from sulphide-rich ore after 360 minutes in an actual cyanidation circuit. Pre-oxidation was effective in enhancing gold extraction by preventing a passive film from forming on gold surfaces. This work aims to highlight efforts undertaken to determine (1) how gold cyanidation is limited by passivation, (2) what reactions and mechanisms are involved during sulphide-rich ore cyanidation, and (3) how peroxidation efficiency of an industrial sulphide ore is controlled by galvanic associations between its sulphide constituents.

Jan 1, 2013

By F. Khomamizadeh

In this study, deep cryogenic treatment was applied to A319 cast aluminum samples. Although the cryogenic treatment didn't have any significant effect on mechanical properties of the well degassed and fluxed samples, but the tensile strength of the samples containing a considerable amount of gas and shrinkage defects was improved surprisingly, This improvement was attributed to the strengthening of the a-aluminum matrix which slows down the propagation of the existing defects. There was no significant increase in the hardness after cryogenic treatment, The abrasion resistance of the alloy was improved after cryogenic treatment, by developing a homogeneous protector shield, composed of abrasive grains penetrated into the soft aluminum matrix and kept tight.

Jan 1, 2005

By A. Warczok

Metal losses in discard slag are the main factor determining overall recovery. The metals are present both in dissolved form and as matte or metallic inclusions, varying in size from 2 to 1000 µm. Pyrometallurgical slag cleaning usually consists of heating the slag, reduction of oxides and settling of matte/metal droplets. Heating the slag decreases viscosity and accelerates reactions. Reduction of magnetite liberates inclusions and facilitates co-reduction of dissolved metal oxides. A significant amount of the matte and metal is present as very fine metallic inclusions, too small for settling. The coalescence of these matte or metal inclusions is required to remove them from the slag. The developed new concept of slag cleaning combines DC furnace technology with an extra magnetic field for vigorous slag stirring, enhancing mass transfer to the reductant surface, accelerating the rate of reduction, and destabilizing the emulsion of matte or metal inclusions. Intensive slag stirring increases the probability of collision of inclusions, will accelerate their growth and will therefore improve settling. The process is carried out in a patented DC channel furnace, where the liquid metal or matte layer acts as a cathode and the floating coke bed on the slag surface is the anode. In the first part of the furnace, a superimposed magnetic field induces a Lorentz's force causing the slag to start an intensive circular motion. The next furnace zone does not experience any stirring and is dedicated for quiet sedimentation of the inclusions. A mathematical model of gravitational coalescence combined with forced slag motion showed the possibilities of effective removal of copper matte inclusions. The results of laboratory pilot scale tests of continuous slag cleaning showed fast slag reduction and confirmed the improved matte removal from the slag. Conceptual analysis shows the potential use of the technology in various other non-ferrous industries, like for example nickel plants. It is also possible to use this technique batch wise.

Jan 1, 2007

By Helmut Ehnes

Over 330 million accidents at work happen world wide every year, only counting those leading to more than four days absence. More than 350,000 end fatal. Two million people more die every year due to work-related diseases. To sum this up: around 2.4 million people die every year because of work conditions. Among many risky industries, mining stands out. While mining represents just 1% of employees globally, it unfortunately represents 8% of all occupational fatalities. Mining operations go along with a variety of hazards. Not only in large operations, as they first come to mind, but also in the manifold small scale mines, with an estimated 13 million labourers worldwide exposed to substances such as dust, mercury and other chemicals, while also dealing with poor ventilation, inadequate space and overexertion. But is the number of severe accidents and diseases inevitable or can we change this situation? We can make mining sustainably safer, but we need a successful strategy to do so. A high potential lies in Vision Zero. Vision Zero is a prevention strategy for a safe future without fatal or serious occupational diseases, work accidents and traffic accidents. First defined as early as in the 19th century by Eleuthère Irénée du Pont, its very successful elements were adopted by many European countries first aiming at road safety, then extended to safety and health at work. Vision Zero?s holistic elements cover technology, workplaces, rules, and people as fields of action. By focussing on severe and fatal accidents, its application increases the level of safety and health overall.

Aug 1, 2013

By A. Consigny

New "clean technologies" to treat mining and metallurgical effluents containing dissolved metals have been successfully applied at mine sites in North America and Asia, treating water flows up to 24,000 m3/day. These clean technologies offer significant benefits compared to conventional alternatives and provide a sustainable solution that eliminates residual waste sludge, improves water conservation, generates revenues from wastewater, and delivers overall improvements to the environment. This paper will profile these technologies, and provide best practice case study examples of their application at mining operations, including data for water chemistry, flows, water quality, capital and operating costs, and life cycle costs of treatment.

Jan 1, 2011

By M. A. Clayton, D. Kinakin

The Mitchell Creek Landslide is a large, structurally controlled, complex bedrock instability located in northwestern British Columbia. Characterization of the landslide using aerial photograph, exploration geology, and geotechnical investigation data has been completed allowing the development of a three dimensional conceptual model of the landslide domains and slope behaviour. Three domains have been identified in the landslide, from top to bottom: the Sliding domain, a relatively intact slab slowly sliding into the valley; the Transition domain, located in the mid slope of the landslide and showing evidence of significant extension and continuing to subside and displace into the valley; and a Toppling domain, at the toe of the landslide in an area of overturned foliation. Movement is greatest in the Toppling domain, with long term estimated rates of movement up to 4 times that of the Sliding domain; the Transition domain exhibits the greatest range of displacement rates, with average long term values approximately double the slower Sliding domain. This paper documents the results of numerical modelling of the Mitchell Creek Landslide with variation in geomechanical properties, basal rupture surface configuration, structural fabric, and pore water pressure conditions. The locations of internal shear surfaces within the landslide have been estimated from surface scarps, structural fabric orientation, and borehole monitoring data. The performance of each numerical model was evaluated against observed behaviour of the landslide. The configuration and properties of the basal rupture surface were identified as critical to model behaviour, as was spacing and location of internal structures.

Jan 1, 2015

By J. D. Wright

This paper describes current milling practice at Endako Mines Ltd., a molybdenum producer in central British Columbia. The various steps in the crushing, grinding and flotation of the ore are outlined, with emphasis on the metallurgy of the latter operation. Tailings disposal and concentrate assaying methods are also described.

Jan 1, 1969

By Maxime Tacher

BRP (Bombardier Recreational Products) designs and commercializes recreational vehicles such as watercrafts, sport boats, snowmobiles, ATVs... The Spyder roadster is the last product in the Can-Am product family lineup. To remain at the forefront of innovation, a hybrid motorization version of the Spyder is being developed in order to reduce fuel consumption and emission of greenhouse gases. But, the addition of electric components (e-motor, lithium-ion battery... ) raises the issue of added weight and volume. This article deals with the mass reduction of this Spyder by optimizing its frame.

Jan 1, 2011

By R. Heikkilä

The utilization of Building Information Modeling (BIM) and model based 3-D control of work machines have increased a lot in new road construction in Finland as well as in other Nordic Countries. Up today, much less attention has been paid into the development of maintenance and rehabilitation processes. As a part of a large research and development program RYM PRE Infra FIN BIM in Finland, a focused research project of the BIM with experiments in total five (5) pilot projects has been performed. A main idea of the new BIM based process has been to utilize mobile laser scanning method for initial data acquirement, the use of novel 3-D analyze and modelling methods for point cloud processing, the use of new type optimization method for the planning of geometric and structural improvements needed for the existing uneven road surfaces, and further, through the creation of 3-D machine control models apply the newest 3- D machine control systems for continuous 3-D control of practical construction work using milling machine and asphalt paver. Finally, an evaluation is made between the new process model and the traditional way of working.

Aug 1, 2013

By A. B. Walker

The effects of the injection of dry limestone additives into boilers for the sorption of sulphur dioxide have been studied in pilot and full-scale systems. The effects of such injections on boiler mass particulate emissions as well as collectability characteristics of the fly ash and reaction products are presented. Implications of the effects on the design and economics of particulate collectors, in particular electrostatic precipitators, are discussed.

Jan 1, 1971

By Hassan El-Shall, Ayman El-Midany, Patrick Zhang

Bench and pilot scale testing results suggest that significant improvement in dewatering characteristics of fine particles could be obtained by the addition of fibrous materials. Case studies involving flocculation and dewatering of wastes from phosphate, bauxite, and kaolin processing plants are presented in this paper. Several dewatering techniques were investigated, including sedimentation thickening, filtration, centrifugation, dewatering on screens, and seepage-induced dewatering and consolidation. Advantages and limitations of commercial application of some of the developed techniques arc discussed.

Jan 1, 2004

By H. Chaouki

The aim of this work is to simulate the forming process of a green anode. For this purpose, a nonlinear compressible viscoelastic constitutive law is presented. The concept of natural reference configuration is considered. Within an isothermal thermodynamic framework, a Helmholtz free energy is proposed to take into account the nonlinear compressible deformation process occurring between natural reference configuration and current configuration. A dissipation potential is introduced in order to characterize the irreversible aspect of compaction process. Thus, the constitutive law is formulated through two equations: 1) an expression of Cauchy stress tensor and 2) a differential equation characterizing the evolution of the natural reference configuration. Material parameters are assumed to be a function of the bulk density. This allows capturing the micro-mechanical phenomena within the chosen macroscopic approach. An experimental study based on compaction tests is carried out in order to characterize the mechanical behaviour of the anode paste. A user's material VUMAT subroutine for finite element dynamic explicit analysis has been developed and implemented in the ABAQUS commercial software. To evaluate the model predictive capability, numerical simulations of the compaction forming process of anode paste were performed. Simulation results show that the constitutive law predicts the experimental trends and gives interesting physical responses. This constitutes a first step toward making a benchmark with experimental results on the forming process of anode paste.

Jan 1, 2011

By M. A. Tomlinson, A. Di Feo, T. C. Cheng

"Goldcorp is evaluating the potential for economic reprocessing of historic tailings at several sites, including the Aunor A facility located in Timmins. The overall project is investigating the ability to recover value, remove sulphide minerals and alternative tailings re-deposition strategies. Desulphurization of tailings will eliminate potential acid generation while improved tailings re-deposition could reduce long-term liabilities and closure costs. Through a task-share project between CanmetMINING and Goldcorp, tailings obtained from Aunor A site have been characterized using mineral association analysis and diagnostic separation techniques. The selected tailing samples contain about 2 g/t of gold. Mineralogical analysis has identified coarse agglomerates bound with gypsum and significant free gold, confirmed by high recoveries in cyanide leach tests. However, despite no evidence of surface passivation on the minerals, conventional flotation techniques were found to be ineffective in concentrating gold or sulphides due to the high fines content and highly agglomerated particles.INTRODUCTION Aunor Mine is one of the historic mines that belongs to Porcupine Gold Mines (PGM) in Timmins, Ontario. PGM has undertaken an extensive mine closure program to remediate the legacy and closed mines with the funding supported by operating mines since 2006. Over the course of 100 years of operation in the Porcupine camp, it is estimated (Stevens et al., 2013) that about 130 million tonnes of tailings have been generated. Aunor Mine produced 2.5 million troy ounces of gold between 1940 and 1984, while processing over 7.6 million tons of ore. The original gold grade of Aunor Mine ores was about 10 g/t. With 95% gold recovery at the time, an estimate of 0.5 g/t of gold remains in the Aunor Mine tailings. Aunor Mine has two tailings impoundment areas: designated as Aunor A and Aunor B. The two sites are similar in size, about 7 hectares each. The amount of tailings in the Aunor A site alone is about 3.2 million tonnes. In 2017, bulk tailings were sampled from five designated locations in Aunor A. They were characterized using mineral association analysis and diagnostic separation techniques. The bulk tailings samples contained about 10% total sulphur, 10% iron, 2% arsenic and 2 g/t of gold. The prime objective of this collaborative work between CanmetMINING and Goldcorp is to facilitate the timely development and deployment of innovative tailings reprocessing solutions, specifically in the areas of desulphurization, and recovery of metals. This work targeted specific tailings of interest to Goldcorp which goals are to improve its environmental footprint and to reduce long-term liability. Thus, it is imperative to look for innovative reprocessing options that can overcome not only technological challenges but also achieve economic benefits to offset the costs associated with reprocessing the tailings. Moreover, the greater goal is to demonstrate and deploy tailings reprocessing solutions to solve one of the industry’s most difficult challenges for a sustainable mining industry in Canada."

Jan 1, 2019

By Michael S. Moats, Prashant Bagri

"In recent years with increasing concerns about energy consumption in hydrometallurgical processing, there is an ongoing attempt to use Catalytic Titanium Anodes (CTAs) for copper electrowinning. For this work, anodes with IrO2 - Ta2O5 coatings were prepared in the laboratory with the same total coating loading but varying the number of layers by changing the speed of withdrawal in dip coating. A second set of CTAs were fabricated on niobium, Ti Grade 1, Ti Grade 7 and Ti Grade 36 metal substrates. All the anodes prepared in the laboratory were characterized using standard electrochemical techniques and subjected to accelerated life testing. It was found that the coating would not adhere to the niobium substrate, the grade of titanium had a minimal to no effect on the life of the anode, and it is observed that as the coating speed slows, there is an increase in the electrochemically active surface area of the coating which seems to directly contribute to an increase in the Tafel slope of the anodes. There was inconclusive evidence on the effect of coating speed on anode lifetime.INTRODUCTIONLarge scale hydrometallurgical extraction of copper has become widely practiced over the last 40+ years. The hydrometallurgical route entails leaching, solvent extraction and electrowinning. With the increasing desire to process refractory sulphides like enargite and chalcopyrite through the hydrometallurgical route, use of hydro-processing of copper is expected to remain high.In conventional electrowinning, copper is deposited on the cathode and an inert anode is used for oxygen evolution. Presently, the most common anode material is rolled lead-calcium-tin and the cathode is 316L stainless steel (Robinson et al., 2013). This lead alloy is fairly inexpensive and is robust, providing lifetimes typically of 4+ years. The main drawbacks of lead alloys are their relatively high oxygen evolution overpotential, the need for cobalt in the electrolyte to reduce their corrosion, the contamination of cathode product by lead, and the generation of harzardous by-products (Hiskey, 1999)."

Jan 1, 2016

By Walter I. Nelson

THE geology of the Copper Mountain mine has been ably described by Dr. Victor Dolmage in Memoir 171 of the Geological Survey. Reference is invited to that paper for a more extended description of the geology of the ore deposits than will be given here. The important orebodies of the mine occur in fragmencal volcanic rocks, parallel with and adjacent to the gabbro of the Copper Mountain stock. In the mine area, the contact strikes N.45°W. and dips either vertical or steeply co the southwest. For a distance of 500 feet or more from the contact, the fragmental rocks have been intensely metamorphosed both dynamically and hydrothermally. The dynamic effects are reflected in the foliation and fracturing parallel with the contact, which occurs throughout the mine, and the volcanic rocks within this foliated zone are, in places, highly schistose. Superimposed upon thi.s structure is a system of fine, straight, parallel frac-tures that strike nearly normal to the foliation (and contact) and dip between 65° and 75° to the north; it is with this last-described fracture system that the ore minerals are structurally associated. The fractures are mineralized with bornite and, to a considerably less extent, with chalcopyrite and some pyrite. A notable characteristic is the extreme fineness of the fractures; even in high-grade ore they are rarely larger than pencil lines. The tenor of the ore, therefore, varies directly with the fracture spacing. Replacemcnr of the host-rock between two or more fractures, varying in degree from finely disseminated sulphides to masses of nearly solid bornite up to 18 inches wide and 2 to 3 feet long, is not uncommon in the higher-grade portions of the orebodies. Two structural types of orebody are recognized in local nomenclature: the 'contact' orebodies, so-called because they occur along the contact; and 'outlying' orebodics, which are enclosed in the volcanics. The former arc tabular or lenticular bodies elongated along the strike and dip of the contact. The 'outlying' orebodies are coniform, chimney-like masses roughly elliptical in plan; with depth, their roots plunge at steep angles toward the contact. All of the orebodies are cut by a number of light-coloured granophyre and felsite porphyry dykes. These dykes-the so-called 'mine' dykes -enter the mine area from the north, curve gently southeasterly across the orebodies, and then cross the contact into the gabbro at the south end of the mine. All the dykes dip vertical to steeply east.

Jan 1, 1941

By F. Bosché

Previous research has shown that ?Scan-vs-BIM? systems are powerful to provide valuable information for tracking structural works (progress, quality, safety). However, the transferability of this capability to other construction areas such as MEP works has not been assessed so far. Comparatively, the construction of MEP systems, in particular pipes and ducts, tends to be more flexible with respect to the positioning of individual components, so that Scan-vs-BIM systems could be defeated when tracking MEP installation works. This paper presents recent results on the feasibility and performance of using a Scan-vs- BIM system to track MEP works. The approach followed is presented and then tested with two real-life challenging case studies were conducted simultaneously but totally independently in Canada and Italy. The results show that, as expected, pipes and ducts tend to be more loosely positioned than structural elements leading to a poorer performance of the Scan-vs-BIM system. Nonetheless, it appears that the system works well to assess the level of conformance of site installation works, providing valuable information for estimating emerging performance metrics like ?percent built as-designed?. In addition, the proposed system could also be useful to accelerate and thus reduce the cost of delivering as-built BIM models for in the case of new builds.

Aug 1, 2013

By Mark Holdsworth

In 2002, Kennecott Utah Copper Copperton Concentrator installed an Expert Control system for optimization of their SAG and Ball milling circuits. The advanced process control has been well received and is utilized well over 95% of the time. In the years since, many lessons have been learned and many advances have been made. Improvements have produced millions of dollars of benefits and have included directly controlling feedrate with complex logic as opposed to using a bearing pressure controller, modifications to how sound is used for control, modifying logic for maximizing asset utilization and using advanced control for automating equipment restart.

Jan 1, 2012