Search Documents

By Shuan-cheng Gu

Roof bed separation often occurred due to the deformation incoordination of surrounding rock following the excavation of mine roadway. Bed separation has effect on the bolts, and the estimation of the influence will directly affect the safety of support systems. In this paper, the hyperbolic function model to analyze the load transfer mechanism on the bolts was simplified as the exponential function form for easy calculation. An elastic-plastic analysis model of the bolt loading occurred by the bed separation was established. And the development low that the bed separation affected to the bolt loading was discussed. According to the parameters analysis of different separation values and locations, the influence law of the bolt loading caused by roof bed separation was summarized. Finally, the effects of bed separation were considered for the bolting design, it was able to provide a reference to the anchorage design of stratified rock.

Aug 1, 2013

By Therese Schneck

The presence of xenon isotopes from in-situ spontaneous fission of short-lived Pu244 has been confirmed in Hadean detrital zircons from Western Australia. Hadean and meteoritic zircons can retain secondary overgrowths developed after primary cristalization at 3.97-3.94 Gyr. On the moon, the metal grain in sample 66095,78 is mantled by troilite, schreibersite and cohenite. High chlorine content FeCl2 is deposited around metallic FeNi. The magnitude of Pollonium-210 to Radon-222 on the Aristarchus plateau spectrum indicates a past greater activity. The Earth Moon system from Nb/Ta systematics is consistent with a Moon iron core delayed to 3,9 Gyr.

Aug 1, 2010

By X. Cao

Friction stir processing (FSP) is used to produce wrought microstructures at the surface of sand-cast aerospace grade magnesium alloy ZE41A-T5. It is found that the microstructure is significantly refined in the stir zone and the flow arm. The stir zone is largely comprised of equiaxed magnesium grains of approximately 4.5 pm compared with about 50 µm in the base cast material. In the stir zone, however, abnormal growth of some grains is also observed. Vickers microindentation hardness tests indicated that the stir zone experiences some increases in hardness. Single surface passes with low distortion, lack of pores and cracks were successfully obtained indicating the great potential of the FSP technique for modifying, improving and repairing magnesium alloy castings. This will probably open new opportunities to apply magnesium alloys in aerospace industry.

Jan 1, 2007

By Y. G. Yaroshenko, V. Y. Baldin, Y. M. Gordon

The manufacture of sulphuric acid from the off-gas of pyrometallurgical processes in the production of heavy metals is one of the common methods of effective recycling of sulfuric anhydrite. The new Impact-Inertial Devices with the rectangular contact channels (IIRCh) and the internal circulation of liquid allow the injection of an absorber into the phase's interactive cell by utilizing the gas stream energy and by this way increasing the sulphuric acid yield and reducing the power consumption. These devices have the following advantages: simplicity of design, smaller size, low capital expenses, absence of irrigating system, high operational reliability, simultaneous cleaning of solid, gaseous and liquid impurities and also cooling of gases etc. The IIRCh efficiency is almost 18 % higher and they require 1.3-2 times lower energy when compared with Venturi Absorbers. Also the elevation of spraying nozzles or injectors is 1.5 times lower in the IIRCh case.

Jan 1, 2004

By Chuan-liu Wang

The bionic non-smooth surface has the characteristics of anti-wear, and reducing resistance. Based on bionic non-smooth surface?s characteristics, a bionic drill bit was developed. When the bionic drill bit is used, a bionic non-smooth surface forms on the crown of bionic drill bit. This surface can be used to extend the life of drill bit and improve drill efficiency. The bionic unit diameter and arrangement were researched in this paper to determine the optimal bionic non-smooth surface for further improving the life and efficiency of drill bit. Four bionic samples having the same structure size, materials and arrangement were designed and manufactured. After being sintered, the abrasion ratios of the four bionic samples were tested, and the results show that the abrasion ratio of Nos. 3 and 2 were similar (only 2% difference) and higher than that of No. 1 and 4. Therefore, the optimal diameter of bionic unit is 1.5 and 2.0 mm. Small diameter bionic drill bits were designed and manufactured, and tested in the laboratory. The results show that not all bionic structure bodies are better than normal diamond bits, except the bionic unit arranged in a reasonable range. When the angle was 24° and 30°, the arrangement of bionic unit were more reasonable, which shows the superiority of the bionic coupling bit.

Aug 1, 2013

By F. Chiesa

Experimental results on thin and thick castings poured in aluminum A356 and magnesium AZ91E by the low pressure permanent mold process have been compared to the result of filling simulations for thin and thick castings. If the results of modeling is reliable when the liquid remains above the liquidus temperature, this is no longer the case when partial solidification occurs. The visco-elastic behavior of a partially solidified liquid is difficult to put into equation as it depends on the amount of shear it has been been subjected to. Attempts to predict misruns with a commercial software has been proven to be very difficult if not impossible; divergence of the numerical solution has been observed unless prohibitively long computing times are used. In order to overcome these difficulties from a practical standpoint, a simple method is proposed which consists in tracking the temperature of the advancing liquid metal front so as to make sure it will always be above so-called `Misrun Critical Temperature' (MCT) determined experimentally for thin and thick aluminum A356 and magnesium AZ91E castings. If the liquid metal front falls below this temperature, a cold-shut or misrun is likely to happen at this location. The values of MCT for thin and thick in aluminum A356 and magnesium AZ91E were determined experimentally on misrun castings of extreme geometries (a thin 2.5 mm wall cover and a 6mm to 25 mm thick bell housing). MCT was found to be lower for magnesium AZ91E and for the thicker castings.

Jan 1, 2011

By R. Vergunst, E. A. Devuyst, G. Robbins

"INTRODUCTIONThe Inca process for continuous cyanide removal from industrial wastewaters was patented in 1984 by G.J. Borbely, et.al. (1). The process requires SO2, air, lime and a copper catalyst. Both free and complexed cyanide are oxidized to cyanate in the pH range 8 to 10. Cyanide bound to iron is removed by precipitation as a ferrocyanide insoluble salt and other base metals are removed as hydroxides.The process was piloted in 1982 on barren bleed solution at Campbell Red Lake Mines Ltd., Ontario (2). Since 1982, the Inca SO2-air cyanide removal technology has been applied in twelve commercial installations. The process has significant advantages over other commercial processes in the completeness of cyanide removal and lower reagent requirements and costs.COMMERCIAL INSTALLATIONSBy the end of 1988 Inca will have applied its patented cyanide removal technology to twelve commercial operations. Three of these, namely Scottie Gold Mines, Dupont of Canada Expl. Baker mill and Carolin, all in British Columbia, Canada, have ceased cyanidation operations but SO2-air cyanide destruction results were good for all mills, particularly so for over two years for the Scottie mill.Removal of cyanide from CIL slurry tailings is applied at Equity Silver (9,500 tpd) and Inca's new 1,200 tpd mill at Inca/Golden Knight. Detoxification of CIP tailings is carried out by Colosseum California (3,600 tpd) and Canamax's Ketza River operation (360 tpd). Repulped tailings from Merril-Crowe flowsheets are treated at Total Erickson's Mount Skukum mill (300 tpd) and Skyline's Johnny Mountain mill (200 tpd) and barren bleed at Inco/Queenston's McBean mill (500 tpd). Lynngold's MacLellan mill (1,800 tpd) treats pond supernatant water. Plating shop cyanide effluents are decyanized at Kuntz Electroplating in Kitchener, Ontario. Many of the above commercial operations were described in some detail in previous publications (3,4). Typical installations are described in this paper. A summary of operating results is given in Table 1."

Jan 1, 1989

By John H. Walsh

"ForewordPart I of this paper, published in the March 1992 issue of the CIM Bulletin, surveyed the probable consequences of a limitation on the emissions of carbon dioxide to the atmosphere for the steel industry. What might be termed the conventional responses to this restriction open to the industry were also surveyed in that section. This section, Part II of the paper, explores a new option - the possibility for the joint production of iron and liquid fuels useful for transportation purposes. In this case, it is shown that it is important to minimize the production of carbon dioxide during the reduction stage to maximize the proportion of the reductant carbon embodied in the fuel. It is also advantageous to conserve hydrogen in the reduction step. In essence, the same carbon fulfills two purposes: it serves as a reductant and fuel for ironmaking and then as a constituent of a liquid fuel. If recovered plastics could be used in ironmaking, the same carbon could serve three useful purposes in turn. The conditions and limitations for the joint use of carbon in such 'cascading' processes are explored below. ABSTRACTIt is becoming increasingly probable that emissions of carbon dioxide from the fossil fuels will have to be reduced to deal with the threat of global warming. This issue is likely to be resolved one way or the other in the period 1995 to 2000 which does not leave much time to develop responsive options. In the intervening period, the policy of the Government of Canada is to stabilize emissions of greenhouse gases at their 1990 level by 2000, by encouraging greater efficiency in the use of energy. Should further reductions prove necessary, economic instruments would probably be employed but these would not be applied before a comprehensive international agreement is reached.There are three main themes in this paper: it is assumed that measures to control carbon dioxide emissions will in fact be necessary by the turn of the century; that there will be a rising need for liquid fuels to supply the world's steadily growing fleet of motor vehicles for many years to come, and that the future niche for Canada's industry in such a carbon-constrained world will be the operation of the energy-intensive industries with efficiency and environmental sensitivity.The steel industry, as a large user of both coal and energy in other forms, would be significantly affected by a need to reduce carbon dioxide emissions. This paper first examines what might be called the conventional responses open to the industry in such a situation and then explores a new possibility for making better use of carbon by the co-production of iron and liquid fuels."

Jan 1, 1992

By J. E. Udd, L. B. Geller

"Mine-shaft wire-rope discard regulations include, among other criteria, a limited amount of permissible loss-of-breaking-strength (LBS). Currently, this parameter is estimated on the basis of non-destrutive-testing (NDT) with electro-magnetic (EM) type instruments. This paper analyses the accuracy with which these estimates have, so far, been obtained in practice.It concludes that while certain types of testers have produced better results than others, the desired accuracy level has not been attained. Also discussed are the putative reasons for this situation, and appropriate actions that the mining industry might wish to take."

Jan 1, 1990

By C S. Stevens

This paper describes the problems encountered and the steps taken to solve them in milling an ore containing relatively large amounts of pyrrhotite. A complex and greatly lengthened flotation circuit was required to recover the pyrrhotite. A very low pH had to be maintained in the cyanide circuit in order to get good recovery of the gold and maintain reasonable cyanide recovery. Introduction D ELNITE Mines Ltd., a gold mine situated about 5 miles by road south and east of the town of Timmins, Ontario, is serviced by two shafts. No. 2 shaft extends from surface to the 2875-ft. level, and No. 3 shaft, an internal winze, extends from the 2875-to the 5275-ft. level. No. 2 shaft was stopped at the 2875-ft. level because of a heavy band of chloritic schist which necessitated a drive to the north for 1000 feet, where No. 3 shaft was sunk. The latter bottomed in the schist at the 5275-ft. level. From the 2500 to the 2875-ft. level in No. 2 shaft, the ore was

Jan 1, 1965

By N. Tounsi

The use of analytical modeling of continuous chip formation in conjunction with orthogonal cutting experiments was presented in the open literature to identify the coefficients of material constitutive equation within the practical range of stress, strain, strain rate, and temperature encountered in metal cutting. Identification of reliable constitutive data was hampered by a lack of a reliable model for the prediction of the primary shear zone thickness that affects directly the effective strain rate field. An original analytical model to determine the primary shear zone thickness is proposed in this paper. It is based on the mechanics governing the material flow in the primary shear zone. Based on the distribution of the hydrostatic pressure and the forces measured from orthogonal cutting tests, the model that describes the thickness of the primary shear zone is derived. To validate the model, FE simulations of chip formation using DEFORM3D were carried out for different materials and cutting conditions. The results of the analytical model are in reasonable agreement with FEM results.

Jan 1, 2006

By Y. Feng

Perovskite structured oxide 15% Y-doped BaCeO3 (BCY15) has been evaluated for use as proton conducting electrolyte in SOFC with propane as the fuel and Pt as both electrodes. Under the fuel cell conditions, BCY15 exhibited high proton conductivity and good cell performances. Propylene was detected as product at the anode outlet, and the product distribution suggests that propane dehydrogenation underwent competition with cracking to lighter hydrocarbons. Stability during cell performance tests showed that there was no obvious degradation for BCY15 electrolyte during operation of C3H8-O2 fuel cell.

Jan 1, 2005

By K. Yoshida

Recently, light magnesium alloy with superior heat radiating ability has been attracting attention in various fields. However cold plastic working of the alloy is very difficult and hot working necessary. Furthermore, the magnesium of products with complicated shapes is difficult, the processing cost is high, and the applicability of the alloy is limited. In this study, a technique for obtaining fine wires and tubes by cold drawing is examined to obtain wires and tubes with high strength, quality and surface morphology, while decreasing production cost. In addition, the shearing strain of magnesium alloy wires and tubes drawn under various drawing conditions was calculated by FEM analysis. It was clarified that cold drawing of magnesium alloy is possible. It was also demonstrated that greater reduction of the cross-sectional area could be realized during cold wire and tube drawing by optimizing the drawing conditions.

Jan 1, 2006

By B. N. Church, R. H. Seraphim, J. T. Shearer

"The Lexington-Lone Star CU-Au deposits straddle the Canada U. S.A. border, south of Greenwood, British Columbia. This 3 km long linear porphyry system occurs in a northeast dipping belt of sheared quartz porphyry and serpentinite. The best grades of mineralization occur in three principal bodies known as the Pit zone, the Northwest zone and the Lexington Main zone. The Pit zone at the Lone Star mine is the largest of the mineralized bodies and consists of fracture fillings and disseminations of pyrite, chalcopyrite and minor molybdenite, hosted by the Lexington quartz porphyry. The Northwest zone, discovered by drilling through overburden near the 49th Parallel, consists of pyrite-chalcopyrite-gold mineralization in the quartz porphyry and the footwall serpentinite. The Lexington Main zone has the highest grade of gold and occurs near the footwall of the quartz porphyry with the mineralogy and setting similar to the Northwest zone. Alteration of the host quartz porphyry is mostly sericitic and chloritic; alteration in the adjacent serpentinite is mostly talc and carbonates.A weighted average of the drill-indicated reserves is 19.5 million tonnes grading 0.56% CU and 0.55 gl t Au.IntroductionThis paper describes copper-gold mineralization associated with the Lexington quartz porphyry in the Greenwood mining camp of south-central British Columbia and adjacent parts of Washington State (Fig. 1).Access to the property is mainly by a network of farm, logging and old mining roads to the U.S. border, 10 km south of Greenwood, British Columbia."

Jan 1, 1995

By G. A. Moruzi

Two sulphide dust secondacy explosions have occurred in the mines of the SUdbury operations of Falconbridge Ltd. during the past 18 months. 'Ihe main similarity between the occurrences is that they both happened in vertical crater retreat blasthole stopes. A relatively high p:,v.tier factor was noted in both instances. other details are enumerated and examined, as well as some results of tests done by Noranda Research on company ore samples.

May 11, 1988

By S. Malopheyev, I. Vysotskiy, R. Kaibyshev, S. Mironov

"In this work, the effect of pre-strain rolling on the annealing behavior of friction-stir welded 6061-T6 aluminum alloy was studied. To this end, the as-welded material was rolled to 10 or 20 pct. of thickness reduction prior to the standard post-weld T6 heat treatment. Three rolling directions were the 3-mm thick sheet were considered: along the welding direction, perpendicular to the welding direction, and at the angle of 45° to the welding direction. At relatively low pre-strains (10 pct.), the annealing behavior was found to be very sensitive to the rolling path, and rolling along the welding direction was most effective in suppressing abnormal grain growth. On the other hand, increasing the pre-strains to 20 pct. of thickness reduction inhibited abnormal grain growth irrespective of the rolling path.INTRODUCTION Heat-treatable wrought Al-Mg-Si alloys are widely used due to attractive combination of strength, ductility, excellent corrosion resistance and low cost (Polmear, 2006). To provide the optimal balance of mechanical properties, these materials are typically commercially available in appropriately work- and precipitation-hardened conditions (Polmear, 2006). During conventional fusion welding, however, the prior strengthening effect is totally lost due to elimination of the work hardened structure and dissolution of the strengthening precipitations. An innovative friction-stir welding (FSW) technology may partially overcome this problem. Due to the solid-state character of this process, which involves very large strains, the welded material is characterized by fine-grained microstructure with moderate-to-high dislocation density, and thus the prior work hardening effect may be preserved or even enhanced (Threadgill et al., 2009; Mishra & Ma, 2005). However, heat input associated with FSW inevitably leads to dissolution and/or coarsening of strengthening precipitates, thus giving rise to the undesirable material softening. In an attempt to restore the strength of the friction-stir welded material, the standard T6 post-weld heat treatment has been applied, but this approach was found to lead to abnormal grain growth (Malopheyev et al., 2016; Mironov, 2013, Mironov et al., 2015)."

Jan 1, 2018

By S. Joshi, E. Asselin

An electrochemical quartz crystal microbalance (EQCM) was used to study the leaching of pure gold in deaerated 1 M Na2S solution. Multiple cyclic voltammograms were measured between -0.76 and 1.242 V (SHE) at 20 mV/sec and 2 mV/sec and the frequency shift of the quartz crystal was simultaneously measured. Both the forward and reverse scans showed oxidation occurred between -0.40 to 0.20V. The frequency shift increased during both the forward and reverse scans in the potential range of -0.40 to -0.06 V indicating electrode mass decreased. Since at -0.40 to 0.20 V oxidation peaks were also observed, part of the oxidation was due to oxidation of gold. Eh-pH diagrams were constructed and showed soluble Au(I)-S(IV) species formed between -0.30 and 0.10 V (SHE). Atomic absorption spectroscopy of the test solutions and the mass change recorded by EQCM both showed about 0.015 mg of gold leached. Since the majority of the frequency shift increase corresponding to gold oxidation occurred at -0.40 to -0.06 V during multiple cyclic voltammogram measurement, the total leaching of gold could be approximated to occur at this potential interval to give a leaching rate of ca. 6.4x10-5 mg/s-cm2.

Jan 1, 2011

By W. Beres, M. Bielawski

Recent research on the development of erosion resistant coatings has been directed to the finite element modelling of the behavior of coating and substrate, and their interface under the impact of eroding particles. The approach presented in this paper is based on advanced computer simulation techniques using ABAQUS/Explicit to investigate stress and strain at the surface and at the coating/substrate interface of multilayer coatings under single particle impact. It was found previously that solid particle erosion mechanisms are predominantly governed by the kinetic energy of the impacting particles. However, recent modelling efforts revealed that effects of various material models could be also significant. Therefore, different material models representing relevant coating and substrate properties were investigated and the effects of these models on the coating/substrate response were studied. Particularly, differences between elastic, elastic-plastic and brittle cracking model responses were assessed.

Jan 1, 2006

A semi-automatic device has been constructed that can be used to check the solution strength of cyanide solutions. It consists of a wheel on which a gold-foil-bearing glass slide is mounted. The wheel moves the gold foil through the solution under test and intercepts a light beam. As the gold foil is attacked by the cyanide solution its light absorption diminishes. The successive in-crease in transmitted light intensity is recorded and gives a measure of the gold dissolution rate. Curves have been obtained to show the effect of cyanide concentration and oxygen content on dissolution rates. Details are presented of the construction of the unit, and some practical operating procedures are outlined. 0 NE of the important, although often neglected, factors in the extraction of gold by cyanidation is the actual dissolving strength of the cyanide solution. This depends in a

Jan 1, 1964

By H. A. Kramer

The Flin Flon mine is at present hoisting 5,000 tons of ore daily. In 1943, a peak production of 6,188 tons daily was maintained. Before discussing secondary blasting, it is felt that a short review of stoping procedure will be of value. A list of papers dealing with various phases of the mining operation is appended. Stoping Practice Stopes vary in width from 30 to 150 feet, in length from 200 to 450 feet, and in height from 200 to 500 feet. A typical stope would be 300 feet long, 300 feet high, and 90 feet wide. The dip of the orebodies varies from 60° to vertical, with an average of 82°. The ore is heavy, having a specific gravity of 4. Both sub-level benching and radial drilling are practised. Blast-hole diamond drills are responsible for 85 per cent of the total production. Two sizes of hole are drilled at present, 11 7 6 -inch and 1%-inch. For bench drilling, the burden on the 1 7/16-inch hole is six feet, with holes on 8-foot staggered centres; in radial drilling, the burden is six feet, with nine feet between the toes. The burden on the l 5/8-inch hole is eight feet with holes on 11-foot centres, or 13 feet on the toe of fanned holes. Holes are blasted with two No. 8 instantaneous electric caps per hole, using 403 Polar Forcite. A powder charge of 0.15 pounds per ton is used, with a tonnage factor of 5 and 6.4 per foot drilled for the two sizes. Two rows of holes are blasted together. Fragmentation is satisfactory with the above drilling pattern and powder charge. However, some overbreak and fall-off locally results in oversize material. It is estimated that, after primary breaking, 75 per cent of the ore will pass through the grizzly openings and 15 per cent will pass the draw points, leaving 10 per cent that must be broken further to pass the draw points.

Jan 1, 1946