Search Documents

By W. M. G. Heeley

In the province of Alberta the coal measures dip at so many different angles, between the horizontal and the vertical, that many different systems of haulage are in use. I will, however, only touch briefly upon the general -systems in use, and devote the major portion of this paper to a discussion of endless-rope haulage and its adaptibility to various conditions in coal mines; dealing in particular with the endless-rope haulage that was installed at Brule during the month of August 1923. In coal seams that are approximately level, and newly opened, hand-putting or tramming from the face is the cheapest, but when the mine is further developed tramming is out of the question, and the use of ponies is the next consideration. The time arrives, however, when mining reaches a point where the economical haulage of coal by horses cannot be done profitably, and then some system of mechanical haulage must be installed. The installation of any system should be carefully considered before any particular type of haulage is adopted, because a great deal depends upon the grade or dip of the seam. Motor haulage is impossible to operate profitably on a grade of over 6 per cent and, while it is possible to use ponies, on short runs, up to 9 per cent, some other means of main and secondary haulage must be installed when a 9 per cent grade, is exceeded. I will, therefore, deal first with secondary haulage, because even though a main haulage is established, secondary haulage can be used to feed the main haulage.

Jan 1, 1925

By E. T. Turner

Introduction 1n assembling material for this paper on Wood Refuse Burning 1 turned first to the records of our early studies of the problem in order to learn how and why certain basic decisions were arrived at and also how it came about that the completed central steam plant differed so much from the original plans. It may be of interest, therefore, to outline the engineering problems as they presented themselves in the early part of 1948, and to indicate the economies involved. Although the principle of using wood refuse as boiler fuel instead of burning it to waste was quite sound, and in fact the practice had been in use for a long time in the boilers of many lumber companies, there was some guesswork as far as Hollinger was concerned in deciding how best to handle the large quantities of wood refuse involved and as to the type of boiler equipment necessary to .burn it efficiently. These problems will be examined first. Hollinger Boiler Equipment in 1948 Hollinger had four separate boiler houses, at Main, No. II, and No. 19 shafts, and a small unit at the compressor plant for heating purposes. Main and No. Il boiler houses operated all the year round; No. 19 and the compressor plant only in the winter. At Main there were four 36-year-old HRT boilers with total available h.p. of 500, at No. II, three 30-year-old HRT boilers with 195 available h.p., and at No. 19 two old field-type locomotive boilers capable of producing 95 h.p.

Jan 1, 1951

By Tapio Leskinen, Jouko Koskinen, Timo Nlltti, Lappalainen Seppo, Pentti Vanninen

"The Courier 300 on-stream analysis system manufactured by Outokumpu has now been in operation at five of the company's concentration plants long enough to give a reliable basis for closer examination of the benefits achieved in control of these processes. The first system was installed at the Pyhiisalmi mine at the end of 1967. Since November 1970, two analyzers have been in operation at Pyhiisalmi feeding the assay data to a process computer which controls the whole plant and does the optimization of the process. In October 1970 the Courier 300 analysis system was installed at S. T. O. LESKINEN J. KOSKINEN the Keretti concentrator of the Outokumpu mine, followed soon by installations at the Vihanti Mine in May 1971, at the new Vuonos mine in November J 971 and at t he Kotalahti mine in December 1971. Since installation of the Courier analysis systems, considerable improvements have been achieved in the control and the economy of the plants. Immediate knowledge of the changes in the process and the possibility for rapid action has resulted in evener production and higher capacity and recovery. The recovery has been increased most significantly at the Vihanti concentrator, which operates on a complex ore. Consumption of chemicals has been reduced at all concentrators. Due to the fact that process control and partly also bilance analysis are not achieved by conventional methods any more, it has been possible to reduce the personnel of the laboratories drastically. Two of the plants, viz. the Pyhiisalmi and the Vuonos concentrators, are computercontrolled. The Vuonos concentrator started operation in January 1972 under computer control from the very beginning. The Pyhiisalmi concentrator has been computer-controlled since 1970. The Courier 300 analysis system was described in detail at the AIME Centennial Annual Meeting (1971). In this paper, less attention is paid to the analysis system. Only the sampling system of the Courier 300 is described in more detail. In the development of sampling equipment, effective use has been made of the company's wide knowledge of the problems involved and the test field offered by its concentrators. The sampling equipment includes secondary samplers and six basically different types of primary samplers, with which most sampling situations can be managed."

Jan 1, 1973

By Paul W. Kingston

In New Brunswick, during the 1970's, rocks of the Lower Carboniferous Windsor Group in the Moncton Basin of the Fundy Epieugeosyncline have been the target of intense exploration and drilling programs. Sylvinite ore was discovered in three structural basins of the Moncton Basin near Sussex through a drilling program sponsored jointly by the Federal Department of Regional Economic Expansion and the New Brunswick Department of Natural Resources. In 1973, exploration and development rights to the western end of the Moncton Basin were awarded to the Potash Company of America. One high-grade sylvinite unit, varying between 15 and 70feet in true thickness, with a strike length in excess of 5 miles, is located near the stratigraphic top of the assymetric, semi-diapiric, locally overturned anticline. Late in 1975, exploration and development rights to the Marchbank Syncline were awarded to International Minerals and Chemical Corporation (Canada) Limited. To date, a stratigraphic evaporite sequence, forming the semi-diapiric core of the syncline, has been shown to contain one major high-grade sylvinite unit averaging 70 feet in true thickness over a strike length in excess of 2 miles. Both properties appear to have potential considerably in excess of that revealed by the exploratory drilling, and both, because of numerous mineralogical, structural and stratigraphic similarities, are thought to be depositionally contemporaneous. Both potash deposits lie within 50 miles of the Saint John all-weather deepwater port, thus affording easy access to eastern and mid-western U.S. markets. Further opportunities for potash exploration in New Brunswick are considered excellent, as there are large untested areas with favourable geology and known potassium water anomalies and negative gravity anomalies occurring in the Moncton and Cumberland basins, and in the Central Basin of New Brunswick.

Jan 1, 1979

By J. L. Bowlby

Introduction In the following discussion, boiler-feed and mine waters will be considered from the point of view of the problems arising from the chemical nature of the mineral and gaseous impurities they contain. The theories underlying some of these problems will be reviewed for the purpose of getting a clearer concept of the problems themselves. Certain terms of a chemical nature, necessary to the discussion, will be explained on the assumption that they are not generally familiar to mining engineers. Finally, an attempt will be made to correlate theory and practice, with the abject of establishing certain limits to factors relevant to the problems, and to show that these limits are justified by practical experience. The general problems occasioned by the presence of mineral and gaseous impurities in boiler-feed and mine waters are: (1) Scale formation and corrosion in boiler systems. (2) Corrosion of mine pumps and pump fittings. These will be discussed separately. Boiler Scale Typical analyses of waters available for use in steam power-plants are given in the accompanying Table (Table I). All analytical data are expressed in grains per Imperial gallon. The bicarbonates of calcium and magnesium in the raw waters are shown as normal carbonates in the Table. Substances in the first five rows constitute the encrusting solids. All the waters listed in Table I would be classified as 'very good' in the schedule of classification for boiler waters adopted by the American Association of Railway Chemists in 1887. In spite of this classification, however, the waters contain sufficient encrusting solids to cause serious scale trouble after prolonged evaporation.

Jan 1, 1934

By R. Viljoen, K. Manns

"The mining industry instinctively follows rule-of-thumb design velocities often based on very simplistic theoretical “economic velocity” optimization calculations to determine airway sizes. Although these are important building blocks in ventilation planning it should be recognized that mines are far more complex and various, often opposing factors, are at play. Therefore, it is important that each ventilation situation be analyzed on a case-by-case basis to determine the best-fit solution for an operation. The ventilation design process should not necessarily be constrained by theoretical optimal economic velocities that become rules-of-thumb. In some cases, this could lead to unrealistic infrastructure requirements and exorbitant capital expenditure. This type of design often lacks corporate support leading to a scenario where no ventilation upgrades are implemented. Economic velocities typically consider the cost of power, development costs and operational risk. These typical rules-of-thumb work reasonably well as a starting off point when considering feasibility of greenfield projects. For established mines that are looking at expansion these rules may not be appropriate due to capital expenditure constraints or geotechnical ground conditions. The theoretical optimum should be reviewed in the case of an established mine where existing infrastructure could perhaps be maximized. For example, the geotechnical risk of large diameter raises at depth may require multiple small diameter raise to maintain the theoretical economic velocity. If a mine has a life of less than 5 years, then the cost of power is an insignificant proportion of the total owning cost. For these mines, operating the ventilation raises at an increased velocity to avoid a complicated and expensive capital upgrade might be the more appropriate option, even though it opposes the traditional rules-of-thumb. Mines which are capital constrained may be better off accepting a higher operating cost for the interim or settle for minor infrastructure upgrades rather than run the risk of the entire ventilation upgrade not being approved at all. This paper explores a number of examples derived from case studies undertaken by the authors for several deep mechanized mining projects in Australasia. The examples explore conditions under which higher than the economic norm would be applicable."

Jan 1, 2019

By J M. Anderson

The cable belt conveyor installation at Craigmont Mines Limited, Merritt, B.C., has the greatest one-stage vertical fall of any conveyor installed overland in Canada. Since the late summer of 1961, this conveyor has carried more than 5,000,000 tons of copper ore from open pit to concentrator site. When the conveyor is loaded, the drive motor acts as an induction generator, delivering power to an external circuit. This paper covers the selection, the operation, the performance statistics, and the installation and operating costs of this conveyor system. Introduction T HE Craigmont mine is located in the south-western interior region of the Province of British Columbia, approximately 240 miles northeast of Vancouver. A moderate climate, good roads, service by the Canadian Pacific Railroad, power from the British Columbia Hydro Authority, gas from the nearby main line of the Inland Natural Gas Company and close proximity to the village of Merritt provide a favourable location for this mining operation. The ore occurrences at Craigmont have a vertical extent of 1,500 feet,

Jan 1, 1965

By Richard A. McIvor

"All mine shaft conveyances in Canada and most of the United States that are supported by a single hoist rope or attachment point and used for transporting persons are required by regulation to be equipped with safety catches and mechanisms. These safety mechanisms, commonly called safety dogs, are designed to stop and hold a free falling conveyance, with a full personnel load, in the event of a hoist rope or attachment component failure. The conveyance’s safety mechanism must be tested under dynamic conditions before it is used to transport personnel. This paper will discuss free-fall testing and it’s results on conveyance free-fall tests performed in the test tower at INCO Limited, Sudbury, Ontario.Topics covered will be free-fall tests on various wood types such as B.C. fir, Karri wood and Trusjoist MacMillan Limited Parallamwood (PSL), comparison of deceleration rates versus free-fall velocity and the influence of safety dog tooth design on deceleration rates."

Jan 1, 1996

The use of QemSCAN in providing mineralogical input to detailed ore and product characterization has proved of immense value in recent years. In this paper, a brief review of selected Cu-case studies is presented to demonstrate the versatility of automated, quantitative mineralogy by QemSCAN. This versatility ranges from measurement and analysis strategies through to data processing and presentation. As a rapid diagnostic service, it is common to find that only grain size, the degrees of liberation and/or ore mineral modal mineralogy are of interest. By contrast, the detail afforded by the simultaneous determination of both gangue and ore minerals can alert mineral engineers to fatal flaws and attributes deleterious to processing that are directly a function of silicate and other gangue mineralogy. Examples of the latter effects include the influence of micaceous minerals and acid consuming species, while the former include fluorine minerals, which can provide both processing and environmental challenges.

Jan 1, 2007

By G. R. Heffernan

"IntroductionTHE PURPOSE of this paper is to give a •brief history of iron and steel in British Columbia, a quick look at the present operations of Western Canada Steel, Limited, a review of iron ore resources and iron and steel markets, and a projection of what the future might hold for the industry in British Columbia.From the Past to the PresentWhile the paper is entitled Past, Present, and Future, in covering the past, which we shall call the time prior to 1947, there is very little to be said. Small shipments of iron ore were made from the Texada deposits by the Puget Sound Iron Company from 1886 to 1907. Total ore shipped did not exceed 70,000 tons. Part of this is believed to have been used in building a United States battleship in 1907 in the Bremerton Naval Yards in Seattle, Washington.In 1914 a small steel mill was started on Lulu island, rolling bars from •box piles and used shafting. This mill operated spasmodically for a few years but finally burned down in 1921. The rolling mill stands were sold to China and are no doubt in operation in China today.In 1916 the City of Port Moody assisted in the financing of a mill which operated on re-roll rails, box piles, and steel ingots made in an experimental electric furnace in Port Moody. This furnace also produced small quantities of pig iron scrap. The backers of the Port Moody mill showed a great deal of enterprise and must have been a very forward looking group, since this was one of the first recorded applications of the electric furnace to small ingot production. Despite their enterprise, the operation was unsuccessful and terminated in 1921."

Jan 1, 1953

By W. J. Langford

"Conventional design criteria assume that the fracture strength of a structural material exceeds its yield strength. Fracture below the design load is not expected, y et many structures have failed in this way. The causes of the fractures are almost always discontinuities such as cracks and welding defects. Linear Elastic Fracture Mechanics (LEFM or simply 'fracture mechanics') provides an analytical framework for assessing the influence of sharp defects on the load-bearing capability of a structure. Fracture mechanics techniques have reached the point of acceptance by ASME Design Codes for nuclear components, and ASTM Standards now include well-defined rules for measuring fracture toughness. Starting with a simple equation which relates applied stress and crack size, the influence of the material's thickness and yield strength can be calculated. Thus, the size of defect which will cause failure under the applied stress may be determined. Armed with this information, the metallurgist can assess the safety of a structure from the viewpoints of non-destructive testing standards, construction standards and conditions of operation throughout its service life."

Jan 1, 1976

By Richard R. Walker, John J. Watkins, Allen C. Amos, Matulich. Angelo

THE KIDD CREEK MINE is located within the Abitibi greenstone belt, near its west end, in an area known as the Porcupine mining camp (Fig. 5). The Abitibi belt, long known for its many major gold and base metal deposits, is the largest Archean (early Precambrian) greenstone belt within the Canadian Shield. In the Porcupine area, the greenstone belt is composed principally of Keewatin (older Archean) basic to intermediate volcanics, with subordinate felsic volcanics developed• locally. Greywacke, mainly of volcanic derivation, occurs associated with and overlying these volcanics. Timiskaming (younger Archean) sediments, principally coarse clastics, unconformably overlie the Keewatin volcanics and sediments. The reader is referred to Goodwin and Ridler (1970) •r. for a more comprehensive description of the Abitibi belt.

Jan 1, 1974

By H. C. M. Gordon

IN every co al mine the hazard of fire in the underground workings is always present. This is a natural condition, because the mineral wrought and the supports normally used are themselves combustible and because underground fires may originate in many ways. The main causes of such fires are: (1) Open lights igniting gas, wood, or the coal itself. (2) Explosives igniting gas or coal. (3) Spontaneous combustion. (4) Electric sparks or short circuits igniting gas, wood, or coal. (5) Frictional heat igniting wood, coal, or oily material. (6) Explosions of gas or coal dust igniting wood or coal. The relative importance of these causes, and others less frequently met with, varies from district to district and depends to a great extent on the equipment and supplies used, on the training and discipline maintained among the workmen, and on the liability of the coal to heat spontaneously. It follows, therefore, that open lights should not be used and that, wherever there is the least possibility of methane being encountered, only locked safety lamps of an approved type should be allowed underground. It follows, also, that only 'permitted' explosives should be used and that the it use should be confined to conditions under which they are ?permitted?. Similarly, electric equipment should be of an approved type and all such stationary equipment should be housed in well-ventilated fireproof rooms. Such rooms, as well as entries to stables and oil houses, should be provided with doors which can be easily and tightly closed and which should be constructed of fireproof material.

Jan 1, 1937

By Frank W. Cole, Sharanjit S. Dhillonn

A new method has been developed for calculating flowing bottom hole pressure in a gas well, using as a basis the general energy equation. Fundamentally, the method shows that a plot of flowing pressure versus depth for a gas well can be represented as a series of incremental .straight lines, with the accuracy in-creasing as the number of increments increase. It is shown mathematically that for most cases the slope of the flowing pressure versus depth curve is essentially constant, in which case a single calculation based on surface conditions will yield acceptable results. In all cases studied no more than two iterations were required for very good accuracy, and in most cases only one iteration was necessary. Several example calculations are shown and the results are compared to other commonly used methods of calculating bottom hole pressures These examples show that the method provides answers which are at least as accurate as other methods usually used, and results in a considerable reduction in computation time.

Jan 1, 1960

By C. L. Popp

The scope is to address issues confronted by parties in the mining industry such as: Mine planners, survey and engineering departments, field teams and subcontractors. Describing approaches and best practices for assembling a project team to identify and create modeling requirements and to implement beneficial results. 3D Machine Control and Guidance tools continue to reduce project risk and attract quality resources with skill sets new to the earthmoving industry. These tools increase production, reduce rework and help with government permitting.

May 1, 2013

By R. B. Ellestad

Introduction Lithium has been known since 1817, when it was discovered by the Swedish chemist, Arfvedson, while working in the laboratory of Berzelius on the chemical analysis of the mineral petalite, LiAl(Si205)2. Development of the chemistry of lithium proceeded slowly, following the early work of Davy, Gmelin, Bunsen, and Matthiessen. Approximately seventy years elapsed before lithium products assumed any commercial importance, and for a considerable period it was a' very minor industry. Their chief early use seems to have been in medicine, and in the production of lithiated water. Other more important uses were gradually discovered, and the industry has had a slow but steady growth. Chemistry Lithium is classified as an alkali metal, along with sodium, potassium, rubidium, and cæsium. Like these, it is a silvery-white metal, which can be cut with a knife; it is harder than sodium, but softer than lead" It is remarkable in having a density of only 0.53 gram per cubic centimeter, which makes it the lightest metal. On ignition in air, it burns intensely to form chiefly lithium monoxide, Li2O. Like the other alkali metals, lithium reacts vigorously with water to form hydrogen and lithium hydroxide. The later is a strong base, and reacts with acids to form salts. The salts of lithium are in general analogous to those of the -other alkalies, but many of them have unique properties. For example, lithium chloride and bromide are extremely hygroscopic, and have a very high water solubility. Lithium fluoride, phosphate, and carbonate, on the other hand, are all relatively insoluble, unlike the corresponding sodium and potassium compounds. In this instance, lithium exhibits its frequent tendency to resemble the alkaline-earth group of elements (calcium, strontium, and barium). Many of the special and valuable properties of lithium are related to the extremely small size of the lithium ion.

Jan 1, 1948

By S. P. Narayan

The hot deformation behavior of Pure Mg and Mg-0.29Ce alloy were studied by isothermal hot compression tests in the temperature range of 250 - 500°C and strain rate range of 10-3 - 102 s-1 in a computer-controlled 50kN servo hydraulic universal testing machine (UTM). The results show that the flow stress of Mg pure and Mg-0.29Ce alloy increases with strain rate and decreases after a peak value, indicating dynamic recovery and recrystallization. Process efficiency was increased by nearly 10 to 12% by addition of Ce in Mg. Mg pure exhibits instability zones between 250-275°C at 10 ? 102 s-1 and 400¬500°C at 101 ? 102 s-1 temperatures and strain rates respectively, rest is the safe deformation zone. Wherein, Mg-0.29 Ce exhibits two low efficiency zones from 250 ? 300°C at 10-2? 10° s-1, 400 ? 500°C at 101 ? 102s-1 and high efficiency zone at 450 ? 500°C at 10-3? 10-1s-1. 4D process maps were generated for the above said alloys which illustrate contours of power dissipation and instability in the 3D space of strain rate, temperature and strain.

Jan 1, 2011

By C. H. Hopper

DIAMOND drills have played an important part in the development of mines for many years. Recently. they have also entered the production field arid the use of diamond drills m the primary breaking of ores has become a big branch of the industry. The writer has estimated roughly that the total diamond drilling in Canada during 1942 was 5,625,000 feet, of which 2,250,000 feet, or 40 per cent, was for blast-holes. This accounts for 6,750,000 tons of ore broken, using the conservative factor of 3 tons per foot of hole. Many consider that the use of diamond drills for blast-holes is the most important advance in mine practice of the past decade, and the industry owes a great deal to the staff of Noranda Mines, Limited, for the pioneering they have done in the development of long-hole mining methods and for publishing their results. A great many mines have followed Noranda's lead. At the Waite-Amulet, Aldermac, Flin Flon, Canadian Malartic, Hoyle, and Matachewan Consolidated mines, most of the ore is broken by long-hole blasting. While the mines were developing new methods, the diamond-drill industry was developing mechanically-set bits and better machines. Through the effective use o smaller, cheaper diamonds, as well as more efficient setting, bit costs per foot are only one-half what they were ten years ago. Few people realize that a diamond bit is relatively inexpensive. The common EXT coring bit, for example, contains some 200 small diamonds, weighing altogether about 2.70 carats which, at $3.40 per carat, cost $9.20. After use, the equivalent of about 100 of these diamonds may be recovered. Therefore the true cost of the bit is only $7.00, made up of $4.60, the cost of the diamonds lost, $2.00 for setting, and $0.40 tax. The trend in machines has been toward specialization for the different classes of rock in blast-hole work. Light, high-speed machines have been developed for soft ores and higher powered machines for hard ores.

Jan 1, 1943

"Developing markets for western metallurgical coal have continued to stimulate considerable exploration activity in the Rocky Mountain foothills and to influence major segments of a wide-ranging carbonization R&D pro-gram. Adjunct studies have included expanded petrographie investigations.Coal preparation has• been principally directed toward utilization of prepared small coal and was, like much of the year's combustion work, strongly influenced by concern over atmospheric pollution. Particular attention has been given to desulphurization and to the suppression of pollutants in combustion systems.In the area of non-fuel utilization of coal, interest has centered on plant nutrients and on a series of coal-based carbons which, inter alia, possess utility as filtration media.Other projects included the development of improved sampling and analytical methods, investigations into the effect of storage on coal proper-ties and R&D in solids pipelining. In addition, a significant volume of basic 'uncommitted' research has been maintained."

Jan 1, 1968

By Lionel A. York

THE first application of the cementation process took place in the year 1864, according to H. Standish Ball, when a break in the brickwork lining at a depth of 270', in one of the Rhine Preussen pits near Homburg, was sealed by running in milk of cement from the surface by means of a small hand pump. At about the same time Monsieur Portier adopted the method in France for repairing breaks in shaft lining. Figure 1 is descriptive of the Portier system and is of interest when compared with modern practice. During the next thirty years numerous attempts were made to improve the process; the general method used in sinking being to put clown bore holes outside the perimeter of the shaft for the purposes of injection. The cementation process was first recognized as an important as-set to mining in 1896 when Monsieur A. Francois developed his method of boring and injecting inside the shaft below the permanent water level. The Francois cementation process rapidly attained fame on the Continent and many shafts were sunk by its use in France, Belgium and

Jan 1, 1961