Search Documents

The aim of all modelling is to replicate geological reality as closely as possible using available data. This paper is aimed at one end of the spectrum, where very limited data is combined with intuitive geological ideas to synthesise models for either target definition or for determining minimum viable mining scenarios. Interactive 3D modelling allows a satisfactory hypothetical geometry of surfaces to be assembled, and provides a fast quantitative method for generating targets. As data flows from exploration, an evolving geological model assists with the progressive evaluation of a prospect. Two case histories are described where this approach has been used successfully, the Mosquito Hill Prospect in Queensland and the Longwood Ranges Platinum Prospect in New Zealand. The possibility is also discussed of hypothetically modelling an orebody which has yet to be discovered. The proper description of an orebody is the foundation upon which all mine design and planning is undertaken. The volumetric accuracy of the model is crucial in valuing an orebody. Geologists must form a geometry which matches the conceptual view of the ore occurrence and ensure that they understand how the computer system used calculates volumes. If the underlying assumptions inherent in the method conflict in any way with the conceptual model visualised for the ore occurrence, then that method must not be used.

Jan 1, 1995

By S Totsuka, P Ortiz, E Prokkola

Electrochemical polarisation techniques can be successively applied to maintain clean surfaces in process environments. The applications are the result of extensive knowledge of the electrochemical nature of process environments, an innovative approach to problem solving and shared æcan doÆ attitudes between the supplier and process owner. Initial identification of suitable applications is based on over 20 years of process and electrochemical experience. The technologies discussed in this paper include Electrochemical Anti-Scaling [EAS], Electrochemical Protection Systems with both anodic [EPSA] and cathodic [EPSC] protection and Electrochemical Flocculation [EF]. Examples of industrial applications are reviewed. Good examples of metallurgical processes which can benefit greatly from an advanced electrochemical treatment are the wet processes involving precipitation, crystallisation and evaporation. Eliminating corrosion and scaling which would otherwise cause process disruptions and quality problems can make a big difference in process profitability. Clear advantages in both cost efficiency and environment friendliness are easily demonstrated. Continuous processing with minimum downtime is one clear advantage. In comparison to the use of corrosion inhibitors, anti-scaling agents and flocculants, the electrochemical polarisation does not increase the environmental load from the process as no additives of any kind are used. In most cases the cost benefits from pro-actively keeping surfaces clean with the help of advanced electrochemistry are substantial when compared to traditional re-active methods and other active treatments.

Jan 1, 2004

By Higuchi K

For the mechanisation or automation of mining, recognition of the shape of mined cavities is basic information. A three dimensional shape measuring system, developed and tested, includes an ultrasonic range finder which is attached to the tip of a serial link manipulator. The range finder can be moved to any position and direction in the operational space of the manipulator. The position of a point on the surface of the object is obtained from the position of the range finder, the direction of the beam of the ultrasonic waves and the measuring distance of the range finder.To avoid collision between the sensor and the object, the manipulator is controlled to trace the surface of the object For the tracing control, another ultrasonic range finder is employed. The test results show that the developed system has high performance.

Jan 1, 1991

On the face of it this is an easily answered question. Modern technology and life as we know it today would be impossible without industrial minerals and the responsible utilisation of mineral resources is essential for the economic wellbeing of the nation. The quarrying industry supplies a high percentage of the industrial minerals used in New Zealand and our role therefore, is to ensure a constant supply of high quality roading and concrete aggregates so that society and the community as a whole can develop. We must do this in a manner which causes the least possible disruption to members of the community, which efficiently utilises all the valuable resources, which causes as little pollution as possible and last but by no means least, creates realistic profit for the operator. It is only by achieving a reasonable profit that we are able to continue in business and therefore play our part in the development of the country. Unfortunately, quarries have a poor image and are not generally popular, as on the whole, they are noisy, dirty and dusty and attract large trucks which create traffic problems. Judging by the amount of restrictive legislation with which we have to comply today, not even government or the local authorities want quarries which presents the industry with some serious problems, some of which will be outlined in this paper.

Jan 1, 1978

In the future, Illawarra Coal, the primary metallurgical coal producer in the southern coal fields of New South Wales, will face many unique challenges not found in other coal or minerals production areas. To manage these challenges and determine the best strategy for the business, Illawarra Coal has adopted a systematic strategic planning process, which starts from the broadest possible options analysis and culminates in a ægo-forwardÆ operating case that individual mine sites use as the basis for short-term planning. This paper will discuss two major topics. Firstly an overview of the Illawarra Coal and BHP Billiton strategic planning processes. This will demonstrate the range of variables and inputs that are required for the planning process, and the system which is followed to evaluate different alternatives for the extraction of the resource. Secondly, having discussed the primary external and internal factors that must be accounted for in the planning process, and the main issues affecting the viability and likelihood of each alternative, the paper will discuss the particular challenges that Illawarra Coal will face in the coming decades. These challenges include: market and price uncertainty; managing impact on surface features, infrastructure and environment; community interaction; transport and logistics constraints; unknown mining environments; lack of geological knowledge; limited surface access for new mining domains; changing attitudes to longwall mining in the Illawarra; ageing workforce; and cost and overhead management. The paper intends to discuss how these issues impact the business currently and how they are incorporated into Life of Asset plans and overall corporate strategy for Illawarra Coal.

Jan 1, 2007

By Doxford CI, Perry AJ

Mining Lease 908, situated on Gorge Creek near its confluence with the present Cape River system, has been subjected to intensive recent exploration for alluvial gold.The gold is hosted by a buried palaeochannel, the Gorge Creek Lead and by an overlying remnant meander of the Cape River. The principal, if not sole, sources of gold within the Gorge Creek Lead are the northwest trending Great Australian Reef and Green's Specimen Reef systems which are situated on adjacent high ground. Lower grade gold bearing eluvial ground separates the reefs from the Gorge Creek Lead. The sources for gold within the old Cape River system channel (Canton Lead) are thought to be situated some distance upstream, one source perhaps being the Lolworth Diggings located 30 kilometres to the northwest.Exploration of previously "heavily dug" ground on both leads consisted of detailed geological mapping followed by the collection and treatment of bulk samples from eight costeans. The wash samples varied in size from 120 to 396 cubic metres. Treatment was undertaken through a commercial sized conventional wet screen and jig plant.

Jan 1, 1986

By M Fimeri, R Williamson

Sample sizing in the iron ore industry requires significant manual effort to collect, transport, and sieve the samples as well as record, process and report the data. Efforts have been made to automate this process, which essentially emulate the manual process, except that a person is replaced by a robot. Even in these cells, the sieving and sizing operation consumes a significant proportion of robot time. The proposed doubling of production from AustraliaÆs iron ore mines over the next five years will place increasing pressure on sample sizing and interest is increasing in alternative automated methods. One such method is the adaptation of computer vision technology which has been successfully introduced into the mining industry in a range of applications including feed size distribution to SAG mills and oversize detection from screening stations. The limitation of this technology is that only the top surface is visible and this is used as an indicator of total size distribution. Obviously in a sample plant, where 100 per cent of the sample must be measured for acceptable quality assurance, this approach is unacceptable. In order to capture 100 per cent of the sample using computer vision technology a monolayer must be formed either by spreading the sample across a moving surface, such as a conveyor or vibrating platform, and passing this under a camera. This will become a æsurgingÆ load which presents specific problems for some types of computer vision systems, namely those relying on a 2D approach. In this paper a 3D computer vision technology will be described which overcomes the problems associated with measuring particle size in a monolayer and experimental results will be presented which demonstrate its effectiveness for lump and fine iron ore sample size measurement.

Jan 1, 2008

The New South Wales Department of Mineral Resources has, since 1974, administered the Derelict Mines Rehabilitation Program (DMRP) to reduce the environmental impacts of abandoned and orphan mine sites. The application of the DMRP is presented in case studies of sites from the South Maitland Coalfield featuring residual drainage of acidic and saline water in a semi urban and rural community setting. The acidity here is typically derived from iron oxidation in shallow underground coal mine workings and in surface emplacements of coal washery reject materials. This paper presents summary information on AMD investigation, monitoring and rehabilitation. The experiences of community expectation, stakeholder consultation and peer review are discussed.

Jan 1, 2003

The ore reserves of the Frieda porphyry copper prospect in Papua New Guinea have been estimated using kriging and an alternative method. Only very erratic variograms could be obtained from the raw data and thus it can be expected that kriging variances will be unrel- iable. The frequency distributions of the two sets of estimates show expected differences and the resulting mineable reserves show similar expected differences. More drilling and the use of disjunctive kriging are needed to produce reliable estim- Ates.

Jan 1, 1979

The paper briefly discusses the benefits to proponents of a formal environmental assessment process. It is argued that any process should be fair, cost effective and efficient, involve all affected parties, and should identify important issues at an early stage. The paper outlines the procedure used in Victoria, and the ways in which it attempts to address the above criteria.In conclusion the paper discusses progress towards a national approach to Environmental Impact Assessment. This is currently being pursued by the Australian and New Zealand Environment and Conservation Council.

Jan 1, 1992

Petroleum exploration and development is vitally important for the future well being of Australia. The Australian petroleum exploration/development industry is alive but not so well. A combination of.:factors point to the industry requiring a much more mature effort in both short and longer-term planning to ensure greater success and effectiveness for petroleum discoveries and development. While many petroleum exploration companies are competently run, there are far too many which will be lucky to survive, even though their exploration areas are highly Prospective.

Jan 1, 1983

By D MacKay, W J. Bruckard

One of the mining worldÆs greatest challenges is to effectively use consumables (ie reagents and grinding media) to maximise metallurgical response, while minimising operating costs. It is anticipated that this paper will provide a logical frame work within which this can be achieved. The current study, at PerilyaÆs Broken Hill concentrator in the lead primary grinding/roughing circuits, examines the dependency of collector adsorption on Eh. The data demonstrates clearly that under the right grinding chemistry the addition of a xanthate collector during grinding can improve galena flotation. Further, operating the ball mill under the desired grinding chemistry regime leads to significant reductions in collector consumption whilst maintaining the metallurgical benefit.

Jan 1, 2008

The issues which are the subject of this paper cover an extremely broad field. In themselves the components of the topic could be the theme, in considerably greater detail, of a two day seminar. Indeed a full course in an academic year would probably not do justice to the topic. I have therefore experienced considerable difficulty in condensing such a broad subject range down to a 30 minutes address and in doing so have tried to, hopefully, provide a little bit of everything for the wide range of professional interests and different levels of commercial, professional and legal expertise represented at this conference. Perhaps my address could best be described as a "bird's eye" view rather than a "worm's eye" view of the subject.

Jan 1, 1990

By W Angerer

This paper describes the design of the marine riser structures, including the design measures for sealing and protection from flooding, dewatering and connection to the main tunnels, for the Gold Coast desalination plant in Queensland. The risers connect the intake and discharge tunnels to the ocean. Construction commenced on both in April 2007. The paper describes the key design criteria for the risers, the construction constraints that influenced the design and the design of the main elements of the risers and the connections to the tunnels.

Jan 1, 2008

By Hutchinson H

Froth flotation is applied to mineral sand concentrates in order to produce commercially viable xenotime concentrates. Experiments indicate that a xenotime product containing 38% Y203 at 47% recovery or 34% Y203 at 83% recovery can be obtained from a 27% Y203 feed. The process involves a primary stage of reverse flotation at which oxide and silicate gangue is floated, and secondary stage of direct flotation at which xenotime is floated. Of the various collectors screened an amphoteric compound was found to be effective at both stages. This was made possible by the addition of sodium silicate at the second stage, which acted as depressant for the remainder of the gangue. Similar studies on a low grade feed material were somewhat unsatisfactory as the grade achieved fell short of what was targeted.

Jan 1, 1990

By Watkins JR

The educational system is a dynamic; a flow resource that can be significantly shaped, changed and - refined by educationists. This paper analyses these various facets of geo- science education in Australia. The Australian educational philosophy is essentially a laissez- faire model, a free market approach without any real government or professional directive or stratagem. Students are therefore free to choose their own educational pathway dependent only upon their ability and the access to courses. Geological education at the tertiary level in Australia is described and critically analysed. There is a real need for a rationalisation of geological education in Australia, and this rationalisation should include not only the number of courses offered but should also aim to fully define both the philosophy and purpose of geological education and the accreditation procedures for the Students.

Jan 1, 1986

The Australian mining industry can expect to be working internationally competitive high quality coal mines during the twenty-first century. Cost efficient mining methods such as high productivity longwall units with heavy reliance on remote control will be standard and worked by well paid and intensively trained operators. Major changes in mine ventilation engineering can be expected in the use of computers and mine telemetry, the understanding of the mine environment and the frequency of mine disasters, the utilization of mine air contaminants for profitable purposes and the provision of a pleasant and comfortable work environment. New approaches to mine ventilation such as air recirculation will have been considered. There will be an increased need for highly trained ventilation engineers. With the present pace of technological change, quite revolutionary new approaches to mining and ventilation can be expected by the end of the twenty-first century.

Jan 1, 1988

Rock bolting provides a supplement or alternative to conventional timber and steel supports. The tensile strength of the bolts lies within a range established by manufacturing quality control. Rock bolt testing determines the ability of the rock, anchor and individual bolt as an assembly to accept load. The.test is performed to the yield strength of the bolt or anchor and deflection is observed. The anchorage index, inches deflection per 1000 lb load increment, is a measure of anchorage quality. This allows comparison with anchorages under ideal conditions. It also permits comparative assessment of roof bolt anchors in a particular environment.

Jan 1, 1971

Open pit planning and scheduling play a significant role in establishing, maintaining and improving the economics of open pit mining ventures.The development of an open pit plan and schedule involves consideration of the following elements:ò the market for the mineral, ò the mineral deposit,ò the treatment process, ò the external factors,ò the mining method,ò the scale of operations, ò the open pit design,ò the open pit schedule,ò the calculation of economic performance, andò the implementation of the open pit plan and schedule.The above factors are described and discussed. Open pit planning and scheduling is the linkage which enables a mineral deposit amenable to open pit mining to meet a market requirement for the particular mineral. To effect this linkage the open pit planner should have a good detailed appreciation of both the mineral deposit and the market.

Jan 1, 1992

The crushing and concentration of ores, as Herbert Hoover commented in a footnote in De Re Metallica, stretches back at least 6000 years. During those years there have been continuing changes and improvements in mineral processing technology. It has expanded greatly in its ability to handle different types of minerals, and lower grade and more complex ores. Australia will be dependent on the mineral industry for the fore- seeable future and there will be continuing demands on the mill opera- tors to improve the technology with regard to efficiency, flexibility and costs. These demands will be met successfully in the future as they have been in the past. This Mill Operators' Conference is an important forum for assessing our present position and planning for the future.

Jan 1, 1988