Search Documents

Builders have been very familiar with iron since ancient times, but because of its weathering characteristics it was relegated to use as a fastening material in unexposed places and bronze became the popular metal for exposed applications. It is of interest that iron nails buried deeply about A.D. 87 at a Roman fortress and carefully covered with clean beaten earth under conditions practically excluding oxygen were found to be almost unrusted 1870 years later. (1) Today, weathering steels, which contain less than 2% of alloying additions, can be used in exposed situations without protection and without experiencing continuous wastage. As we all know the steady access of atmospheric oxygen to the surface of plain steel causes continuous corrosion. Weathering steels, on the other hand, due to their alloying additions develop their own impervious surface layer which limits the access of atmospheric oxygen and effectively limits corrosion. Table 1 shows the chemical composition of a plain carbon steel and a typical weathering steel. Fig. 1 shows what we refer to as direct corrosion - time curves in which corrosion loss is plotted against time of exposure in an strial environment. The weathering steel has a high rate initially which then decreases steadily for about three years, as the stable rust film builds up. This is followed by a practically linear relation where the very low corrosion rate, according to one school (2), is due to a blocking of the rust pores by insoluble complex salts formed from interaction of the oxidation products of the separate alloying elements. The start of the linear region represents a total corrosion loss of only about 2 thousandths of an inch.

Jan 1, 1970

By M Noy, P Hawkes

Improvements in the drill and blast process can impact on loader performance in a number of ways. The main effects being improved loading cycle times, less non-productive cycles such as oversize removal, clean-up and face raking and better bucket fill factors. The impact of improved loading cycle times on the overall cost and productivity of the load and haul cycle is very much dependent on the loader truck match and the management of the haul fleet. Previous work has shown that a 20 per cent improvement in dig cycle times may only lead to three per cent or less improvement in the overall productivity of the load and haul process. However, improving the mass loaded per pass by five per cent will lead to a five per cent improvement in productivity for any given haul fleet situation, assuming sufficient truck capacity. Work by Orica Explosives at Lab ChrysotileÆs Thetford Mine, Quebec, Canada showed a relationship between muckpile fragmentation and truck payload. With this in mind, work was carried out to determine the effect differing muckpile fragmentation distributions can have on excavator bucket fill factors. This work was performed in the laboratory to a 1:100 scale. Nine different distributions were used. These were characterised by the Rosin Rammler parameters, xc the characteristic size, and n, the uniformity index. The values of xc and n used were modelled on those previously measured at a Sydney quarry. For the range of distributions measured, it was found that the fill factors were lowest at a low characteristic size and a high uniformity index and highest at a high characteristic size and a low uniformity index. In other words the best fill factors were achieved with a more dispersed muckpile distribution with a larger characteristic size. The difference in fill factors was 16 per cent indicating that controlling the drill and blast process to produce a specific muckpile distribution can have a significant impact on the overall cost-efficiency and productivity of the load and haul process. Field measurement by Orica Explosives at a quarry in Canada supports this conclusion showing improvements of up to seven per cent in average bucket load by either increasing the characteristic size or decreasing the uniformity index of the muckpile.

Jan 1, 1999

By Siddall B

A brief review of the capabilities and practical limitations of blast simulation packages has been carried out. It is concluded that the simulators accurately reflect size distributions in the mid-ranges of 0.1 to 1.0 in, but are less reliable

Jan 1, 1998

Over the last few years several important developments have taken place in the Electro- lyte Purification Plant at Copper Refineries Pty. Ltd. A fully automated system for the continuous removal of arsenic has been develop- ed. A submerged combustion process for the removal of nickel has been developed to a stage where patent coverage has been obtained in most of the copper producing countries. A plant has recently been commissioned for the production of Tetra Cupric Arsenate, which it is hoped will find a ready market in the timber preservation industry.

Jan 1, 1974

By P Mason, J F. Huntington, K M. Scott

Short-wave infrared (SWIR) spectral reflectance of the hydrothermally altered volcanic rocks in the footwall of the Hellyer Zn-Pb massive sulfide deposit was measured with a portable PIMATM infrared spectrometer. The Al-OH absorption band was used to derive information on the cation composition of white mica. The wavelength range of the Al-OH band from 2194 nm to 2222 nm reflects variation in the number of octahedral Al (Alvi) in white mica from 3.9 to 3.2 (based on four octahedral cations per formula). This Alvi range indicates a substantial compositional variation, covering most of the compositional region between muscovite (Alvi = 4.0) and phengite (Alvi = 3.0). Moreover, the spectral reflectance data show that the compositional variations of white mica are spatially related to the hydrothermal alteration zoning, such that the white mica of more phengitic composition tends to form in the main upflow fluid channels in the centre of the footwall alteration system. The results suggest that the octahedral Al content of white mica, which is spectrally definable by the wavelength of the Al-OH band using a field instrument such as the PIMATM, can be used to map fossil hydrothermal systems and potentially as vectors to mineralisation.

Jan 1, 2004

By T Hausler

The pitfalls, pleasures and management issues associated with international and remote projects are diverse.However, no problem is insurmountable and if an engineering team chooses (by luck or good planning) to push through the difficulties, success can mean an extremely satisfying experience for individuals and a significant, positive result for an organisation.International projects are not for the faint hearted or inflexible. Working in foreign lands with people who may or may not speak English and who may not initially respect you can become mentally and physically tiring.Sometimes the challenges are not fully explained to individuals in advance. Individuals then often learn about the challenges ù and discover solutions ù on the job. While this initially puts great pressure on individuals, matters improve eventually, especially when the locals come to understand that you are on site to make a positive difference.This paper will discuss aspects of a recent international project including meeting international clientsÆ expectations, dealing with cultural differences, social reckoning, environmental issues, and personal challenges. Specifically, it will cover aspects of working within a Russian cultural setting and overcoming social barriers.The paper also presents coping strategies for long periods of time spent away from home in remote places with extremes in weather beyond the normal experience of most Australians. For example, dealing with the effects of the spring thaw and coping with temperature ranges of -45 to +45¦C.Lastly, and possibly most importantly, there will be a focus on the role of translators. They have the power to make an engineer everyoneÆs best friend or, on your behalf, to order cold chicken liver and heart salad for lunch. If an engineering team can establish a working relationship with translators, they can become an invaluable asset and both on and off site.CITATION:Hausler, T, 2013. Achieving success in large-scale, remote area metallurgical plant projects, in Proceedings MetPlant 2013 , pp 539-552 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

A new approach to strategic planning, the Life of Business Optimisation System (LOBOS) optimises production systems from the scale of stopes in a single mine to an entire business strategy consisting of multiple mines and products competing for capital and processing capacity. LOBOS has optimised cash flow for a wide variety of operations, including large metalliferous or coal mines and as an aid to high-level strategic business optimisation solution to multi-mine/processing/product complexes. This paper discusses the application of optimisation technology to strategic planning with an emphasis on project evaluation with examples on the application of LOBOS to a variety of recent projects.

Jan 1, 2007

By Graham JW, Cullen GV

edicted increase in, Aluminium production and the possibility of a diminishing supply of petroleum coke for anode electrodes in alumina reduction cells makes it desirable to find alternative electrode materials. Brown coal char, with a lower ash content and with an elemental purity similar to petroleum coke, has been produced by leaching in hydrochloric acid, washing with water and charring at 115000. The cost of processing is estimated to be competitive with petroleum coke. Without further processing the bulk density and real density were undesirably low, but. by briquetting the coal before charring and crushing, the bulk density was improved to 92 per cent of the petroleum coke value and the Particle density was improved to 92 per cent of the density of petroleum coke by water-displacement or 75 per cent by mercury displacement. Pre-baked electrodes were prepared from the char alone, mixtures of petroleum coke and char and from petroleum coke alone, all bonded with coal tar pitch. The electrodes were tested for the usual physical properties and were, evaluated for performance in a laboratory size alumina reduction cell. Electrodes based on brown coal char alone were found to be inferior in physical properties, and performance, but mixtures of the char and petroleum coke, despite poorer density, electrical resistivity and carbon consumption on a theoretical basis, in performance tests gave up to 17 per cent better carbon consumption per weight of aluminium produced and 21 percent better electrical current efficiency than the electrodes based on petroleum coke alone. It is suggested that larger scale tests are warranted.

Jan 1, 1970

By A McKay

The Great Artesian Basin (the Basin) is a large aquifer system underlying more than 20 per cent of continental Australia and most of Queensland. The aquifers of the Basin are an important water source for many industries, including the mining sector. The Queensland Great Artesian Basin Water Resource Plan (the Plan) was released in March 2006. The Plan provides a framework for the long- term holistic management of the aquifers in the Queensland Section of the Basin, in a manner that is consistent with the strategic management plan for the Basin as a whole. The paper describes the Basin and summarises trends in the demand for water in the Queensland section of the Basin. It describes the broad framework for management of the Basin by the individual Australian states, as well as the planning entitlement framework for water resource management in Queensland. The paper discusses the content of the Plan. This includes: the division of the aquifers into management areas and management units for management purposes, provision for protection of the flow of water to springs, limits on further allocating water, provision for a competitive process for access to new water and provision for water trading. Under the Queensland planning and entitlement system a resource operations plan is prepared to specify operational arrangements to implement a water resource plan. A resource operation plan for the basin is expected to be finalised before the end of 2006. The paper summarises the likely content of the plan.

Jan 1, 2006

The Warner Process has been devised to produce zinc metal directly from sulphide, thereby reducing the requirements for purchase of large amounts of energy in a special form. The process conditions for a practical process have been evaluated in an extensive program of research and development at the University of Birmingham. Recorded data now exists to take the process forward to commercial use within the next five years. The industrial economics have been evaluated. The cost of making zinc metal from zinc sulphide ore can be substantially lowered due to the reduced energy cost, locating zinc production in the neighbourhood of the mines and increasing ore to metal recoveries - particularly for fine-grained and pyritic ore. Integration of a Warner Furnace with a zinc mine and concentrator can result in a highly attractive return on capital Invested.

Jan 1, 1993

Material sampling theory is well established in mineral process monitoring, improvement and control. It has been much enhanced by fundamental contributions due to Gy. When GyÆs sampling theory is applied to sampling inspection and monitoring, it provides estimates of average quality or extent of contamination. It also provides estimates of uncertainty, but these often ignore uncertainty in estimated variograms or other measures of variability. Risk assessment is often an implied task in sampling inspection and quality monitoring. A valid technique of risk assessment needs to take into account the uncertainty in the variational measures themselves. Standard statistical tolerance limit calculations which do take such uncertainty into account can be adapted to develop a technique for handling uncertainty in variational measures such as the variogram. Data from a published example is used to illustrate the technique.

Jan 1, 2005

A philosophy is presented that new graduates in mining and metallurgy should be equipped to use computers during their under- graduate courses, should be aware of the capabilities and costs of a wide range of computing equipment, and should receive sufficient stimulus to become involved in applying computers for the benefit of the mineral industry. A program is presented in which computer applications and "hands on" involvement with computers are integrated into the progressive stages of the undergraduate courses in Mining and Metallurgy. In this respect, the role of the computer is to assist the student by performing time consuming tasks, to demonstrate the industrial applications of computing, to extend the scope and complexity of the tutorial, assignment and project work which can be undertaken by the student, and to provide the essential first stepping stones toward continued useful involvement with computers during the graduate's working life.

Jan 1, 1977

By Martin CH

Over the past forty years colliery management has coped with intensive mechanisation and other rationalisation of traditional conditions to accomplish increases to outputs by miners, mines and nationally. The basic managerial function of planning, organising, directing and controlling have adjusted and expanded to current management demands, including the detail of achieving the highest possible efficiency, particularly in forward planning. Although industrial aspects have vastly improved, there are lingering problems. Safety is not necessarily the basic ingredient of any industrial events-which occur but is always paramount. Likewise some legislative changes may have elements of political and particular vested interests and conservation of technical expertise may be threatened by such frustrations. Not only technical excellence is required, but particular attributes of the individual are required in management evolving from "simple owner management to the complete corporate approach required for the multidisciplined operations of to-day".

Jan 1, 1988

A generalised mathematical model for hydrocyclone classifiers was developed by the author (Nageswararao, 1978) using dimensionless groups which include phenomenological characteristics as independent variables. This model is incorporated in JKSimMet, the steady state mineral processing simulator developed by JKTech.Recently, when this model was rewritten (Lynch and Morrell, 1992), in terms of variables other than those used by the author, a few errors have crept in. For example, while the exponent of (Du/Dc) in the equation for d50e should be negative (-0.47), it was recorded as positive (0.47). Also, the exponent of (DoIDe) in the equation for pressure drop should be 0.67 and not 0.60. In the same equation, the exponent of Dc would turn out to be -0.10 and not 0.15. These are clearly attributable to typographic and rounding off errors, while transforming the original equations.More recently, Cilliers (pers comm) has done a comprehensive evaluation of the major semi-empirical models for hydrocyclones.He observed that the major difference between the cyclone model developed by the author and other models lies in the method of quantifying the effect of spigot diameter on d50e. He noted that while all other models predict an increase in d50e with a decrease in the spigot diameter, the model as cited by Lynch and Morrell (1992) predicts just the opposite. However, he conjectured correctly that the discrepancy could be due to a typographic error. As the model is still unpublished, it is felt that the original model equations should be recorded with the correct exponents, so that errors in predictions other than those due to the limitations of the model itself could be avoided. They are given hereunder.

Jan 1, 1995

The Prospero orebody is a part of the Helene mine at Cosmos and was scheduled to begin production in March 2008 after the exhaustion of the Tapinos orebody in the same mine. Treatment of the Tapinos orebody was challenging and it was envisaged that Prospero would have similar properties given that it was also anomalous in deleterious elements and would be of a similar mineral hosting. It was deemed necessary to undertake a metallurgical test work program to identify any potential processing issues, complex mineralogy or significant metallurgical domains. The paper discusses the processes which were employed to undertake the metallurgical test work program and describes the aspects that can be employed by other developers to quickly and effectively assess potential future orebodies. It will demonstrate that the work was successful at determining expected metallurgical behaviour, providing direction for mining operations and highlighting areas for more extensive research.

Jan 1, 2009

By Staude W, Rosser A

Due primarily to the publication of the Fitzgerald Report the impact of taxation on the mining industry and the amount of taxes actual- ly paid by the industry have become items of intense debate. However, the discussion has been governed more by impassioned rhetoric than considered logic. It is equally as wasteful to the economy for the mining industry as a low cost efficient export earner to be punitively taxed, as it is for the industry to be given excessive taxation assistance. A comparison of the effect of five tax- ation policies on the cash flow of a capital intensive mining project is presented. The policies considered are Liberal 1969, Liberal 1976 with and without the coal levy, Labor 1975 and Labor 1976. The mining project used in the analysis is modelled on published estimates for the proposed Nebo coal project. The analysis is equally applicable to any large mining or petroleum development.

Jan 1, 1977

By North R. A

The Queensland Mining Act 1968-1972 has now been in force for almost two years. The Act was completely re-written and has made for easier working, e.g., there is no distinction now between Gold Mining Leases and other Mining Leases. For the first time in the history of Queensland, provision has been made for caveats, so that options etc. can be protected. The chief problem which has arisen so far has been the question of the Government issuing mining leases to the holder of an Authority to Prospect over areas which are included iri its Authority. Litigation has taken place and an Appeal, it is understood, will shortly be heard by the Privy Council. The provisions dealing with labour conditions have been brought up-to-date and generally speaking, they are quite clear as to the responsibility of the Lessee. The Mining on Private Land Act has been repealed and the provisions relating to mining on private land are now a part of the Mining Act itself. Previously, the holder of a- mining freehold did not have to pay royalty on

Jan 1, 1974

By S M. C Verryn

The amount of raw material used in the production of cement can be reduced by partially supplementing it by pozzolanic waste material without changing its properties negatively. This paper discusses results of an investigation using slag from the Pt industry, from the production of steel using Midrex processes as well as fly ashes from different coal power plants in South Africa. These are blended in a 20 per cent slag or fly ash to 80 per cent cement ratio. The properties of the mixtures depend on the phase composition, chemistry, grain size and the sources of the materials. The results are promising, but show variable behaviour depending on slag and cement composition. Compressive strength tests as well have heat flow curves showing the hydration behaviour, indicating that 20 per cent addition of slag or fly ash to ordinary Portland cement is viable. There is a large potential to use slag in cement mixtures and this study can be used to develop cements that will positively influence CO2 emissions and help to reduce large slag and fly ash stockpiles.

Jan 1, 2008

Mine haul road design at Bougainville Copper Limited has undergone significant changes since mine start-up. Selection of 95 tonne trucks and the subsequent replacement by 155 tonne units is discussed, with particular reference to haul conditions within the mine. Changes to haul road design and construction practices are detailed which have lead to improved standards and tyre life. INTRODUCTION Bougainville Copper Limited operates one of the largest copper mines in the world at Panguna, Bougainville Island, in the North Solomons group of Papua New Guinea. The mine commenced commercial operation in April, 1972 and current planned production is 198 000 tonnes of material per day, of which 115 000 tonnes is ore averaging 0.46% copper. Annual total planned production is 72 000 000 tonnes to yield approximately 150 000 tonnes of copper with significant quantities of gold and silver. The mine operations workforce now consists of national employees up to General Foreman level.

Jan 1, 1982

By R West

The Olympic Dam smelter facility processes copper concentrate feed using direct-to-blister smelting technology to support the current site production rate of 225 000 t/a copper. The metallurgical control of the Olympic Dam smelter is largely managed from a single central control room. Control room operation and management is therefore a key function in ensuring safe and reliable operation of the smelter, including identifying and initiating control of abnormal events. As part of a consolidated smelter reliability improvement program, a team consisting of process and control system engineers was formed. The teamÆs charter was to address and resolve the alarm flooding issues being faced by the control room technicians and the lack of an up-to-date base of supporting functional documentation. The project was successfully resourced with WorleyParsons metallurgists, Citect PLC technicians and the on-site technical team. Implementation was conducted over a 12 month period with the goal of achieving best practice alarm levels. The goal was achieved through a systematic process of alarm design review that analysed every configured alarm versus best practice design standards. Innovative concepts such as group-based alarms, first-up interlock displays, graphic only alarming, alarm help and alarm shelving were developed and implemented in conjunction with improved alarm masking. Total configured alarms were reduced from 20 000 to 5000 while the alarm rates were reduced from in excess of 200 alarms per hour per controlling technician to best practice levels of less than 12 alarms per hour per controlling technician. Completion of this program has provided a firm foundation for implementing further control optimisation and was a key activity in supporting sustained smelter reliability levels.

Jan 1, 2005