Search Documents

By G W. Wilson

Rehabilitation of tailings impoundments is one of the most challenging aspects in mine closure, as not only does the potential for producing leachate pose a challenge to the rehabilitation designer, but also other aspects such as stability and settlement must be considered. The water balance of a tailings impoundment is unique in the sense that it usually hosts a pond that in turn causes a phreatic surface in the impoundment. The position of the phreatic surface defines the saturated and unsaturated zones in the impoundment, which of course varies spatially and temporally. Predictive modelling for this hydrologic system becomes difficult, as numerical models capable of analysing the combined saturated/unsaturated zones are not adequately refined to accurately solve the flux boundary problem for infiltration at the surface of the tailings. This paper describes the development of a flux boundary model that enabled accurate modelling of the unsaturated zone in the tailings impoundment at Kidston Gold Mine, Queensland, Australia. The technique made it possible to accurately predict the spatial variation of infiltration to the tailings as a result of the presence of the phreatic table. The conceptual model defines the boundaries for the Kidston tailings dam, based on a generalised cross-section through the dam. Firstly the shape of the top boundary is described as a function of the particle size of the tailings associated with particle segregation that occurs due to the hydraulic placement of tailings. This function was rigorously tested using in situ infiltration tests and laboratory materials testing. Defining the bottom boundary of the section, ie the phreatic level was done by physically monitoring the phreatic level with 42 piezometers strategically located on the tailings dam. Analysis of this data led to the fixing of this bottom boundary through the introduction of a function that mimicked the shape of the phreatic level. The material properties of the surface layer, specifically the saturated permeability that would govern the infiltration/exfiltration rates of moisture through the top boundary layer were defined on the basis of extensive field and laboratory material testing. A function for the saturated permeability was developed on the principles of particle segregation. Finally a procedure is described for the application of the new conceptual model for the evaluation of the spatial infiltration to a tailings surface using the rigorous one dimensional surface flux boundary code SoilCover. The solution of the calculation described above was then used as the top boundary condition in conventional three dimensional saturated/ unsaturated flow codes, and verified against measured seepage rates from the tailings impoundment under drains. It was concluded that the developed spatial flux function was in deed a most rigorous representation of reality. Although the methodology presented here was applied to the Kidston tailings impoundment only, the authors believe that the principles are directly transferable to any tailings impoundment that has a varying phreatic zone thickness due to the presence of a pond. The mathematical equations describing the typical cross-section would be site specific, but the approach and ultimate solution methodology would be directly transferable.

Jan 1, 2003

By D A. Williams

The conventional method of transporting mine tailings from a process plant to a tailings storage facility (TSF) is in the form of a low to medium density1 slurry, which can be pumped using centrifugal pumps. Over the past several decades, therefore, mine operators have generally adopted this default approach. There are, however, some convincing arguments why consideration should be given to thickening the tailings slurry to a higher density paste consistency. In particular, the minimisation of environmental impacts, the reduction in water consumption and the cost savings relating to TSF closure make paste an attractive option for the life of mine tailings disposal. There are several environmental impacts that are associated with a conventional slurry TSF, such as land sterilisation, aesthetics, dust, seepage and acid mine drainage. Some of these impacts, such as dusting, may be difficult to mitigate while the TSF is in operation. Others can be influenced by adjustments made to the tailings slurry density at the plant. Unplanned fluctuations in slurry density and/or viscosity can have a significant influence on TSF performance and can exacerbate the environmental impacts relating to the facility. Relatively minor changes in the solids content of the slurry can affect tailings beaching behaviour, degree of segregation, position of the phreatic surface, amount of freeboard, consolidation behaviour, placed (settled) density (and hence TSF capacity) and in situ strength of the tailings. Paste is a non segregating slurry and many of these effects can be minimised at the TSF when the tailings slurry is thickened to a paste. These improvements are manifested by reduced seepage, flexibility in selecting an appropriate final landform, ability to rehabilitate progressively and reductions in plant water usage. It is possible to minimise environmental impacts of a TSF through the use of tailings paste. Ideally the paste production plant should be part of the initial design of the process plant. However, significant benefits can be gained by adding a paste production plant at some time later in the operational life of the mine to reduce environmental impacts and facilitate an environmentally acceptable TSF closure.

Jan 1, 2002

There is considerable variability in the level of detail incorporated in prefeasibility studies relating to mining developments. Hence, when undertaking a review or audit, it is critical to attempt to ascertain at an early juncture precisely who has compiled the various facets of the study, for what purpose it was intended and the terms of reference given to the authors. Likewise, when commissioned to undertake an audit it is preferable to have proper terms of reference and to be aware of the purpose to which the audit will be put.These factors will influence the degree of detail an auditor would expect to find in the study and consequently, the degree of effort/time required for the audit process. In most instances audits do not imply recalculation of the entire study or modifying it in anyway, but involve an overall assessment of the methodology used, combined with spot checking of detail. One of the most difficult aspects is to determine a realistic order of accuracy for the overall study when the accuracy of the individual components may differ markedly.

Jan 1, 1990

By Botz R. W

Macroscopic and microscopic studies of the outburst-prone Gemini Coal (Bowen Basin) showed that outbursts were associated with a localized inertinite-rich ply. Previous studies of the Gemini Coal had shown a general relationship between desorption rate, regarded as a good measure of outburst proneness, and inertinite content of coal samples.Desorption rates increased with increasing inertinite content and were highest for inertodetrinite-rich samples. These results suggest that inertinite content and composition play a significant role in outbursting and may be useful in identifying outburst-prone coals, which could be confirmed by desorption measurements.Consequently outburst-prone areas in the Upper Permian coal measures ofthe Sydney, Gunnedah and Bowen Basins have been defined using a combination ofthe parameters, inertinite content, depth ofcover and coal rank. In the Upper Permian, inertinite-rich coals are confined mainly to the top of the coal measures, except in the Sydney and Gunnedah Basins where an inertinite-rich interval (Bayswater Coal and correlatives) is also present towards the base of these measures. Only a small area ofthe central Sydney Basin, butmuch ofthe north-eastern and north-central part of the exposed Bowen Basin is considered outburst prone on the basis of these parameters.The most outburst-prone inertodetrinite-rich lithologies have a patchy and unpredictable distribution in the top of the Upper Permian coal measures. They can be defined only by sampling and petrographic analysis at the subsection level.

Jan 1, 1986

By Howard G. L

The gold treatment plant of Great Western Consolidated N.L. is at Bullfinch, Western Australia, 22 miles north of Southern Cross, which is 100 miles west of Kalgoorlie. A railway to Southern Cross connects the mine with the main Perth-Kalgoorlie line.The plant, which commenced operations on the 31st October, 1952, was, designed by Messrs. Alex: Stewart & Co. in consultation with the technical staff of Western Mining Corporation Ltd. to treat 1,000 long tons a day, made up of approximately equal parts of quarry oxidized ore and underground sulphide ore, by moderately coarse grinding (2-3 per cent plus 65 mesh Tyler) and straight cyanidation without straking. The design had to allow for future treatment of all sulphide ore at the rate of 40,000 tons per 28-day periodand to make provision for the possible later inclusion of preaeration treatment.The test work on .which design was based was done on representative development samples, the mine being divided into zones for this purpose, to check possible local variations from average treatment behaviour. Proposed mill feed mixtures were made up from time to time for complete ore dressing tests, which were conducted in the Western Mining Corporation laboratory at Kalgoorlie.The chief feature of the design was that the plant had to handle the extremes of very soft, poor settling and filtering oxidized ore and very hard, good settling and filtering sulphide ore. On one hand, crushers and mills had to be large enough to handle the sulphide ore and on the other, thickeners and filters had to be large enough to handle the oxidized ores.The design is marked by simplicity, the use of large units of equipment, and flexibility to cope with a variety of ores.

Jan 1, 1956

By J B. Farrow

The AJ Parker Cooperative Research Centre for Hydrometallurgy carries out research on behalf of, and in collaboration with, the Australian mining industry. As might be expected, much of its research is directed towards improving the efficiency of alumina and gold processing plants. However, the Centre also carries out research of relevance to base and other metal producers. A key element in its work is the successful transfer of its technology to the companies with which it is working. In general, this is achieved in the following five steps:definition of the problem through discussions with the company commissioning the research; execution of the research; assessment of the research findings; testing of the research findings by pilot plant or on-site trials; and implementation of the results on the full-scale. This pattern is exemplified by the work carried out by the Centre to improve the performance of gravity thickeners which are used throughout the minerals industry for solid-liquid separation. The research has focussed mainly on ways to optimise the use of flocculants (long chain polymers) to enhance thickener performance. It has been shown that the way the flocculant is mixed with the slurry is of profound importance. Computational fluid dynamics modelling of the feedwell region of thickeners and laboratory and plant flocculation studies have been used to determine better ways to contact the flocculant with the feed slurry. Implementation of these and other findings on the full-scale confirmed that improvements in thickener performance were indeed possible. As a result of this AMIRA funded thickener technology work, there have been considerable savings to a number of Australian mineral processing companies, through improved operation, higher throughputs and flocculant savings.

Jan 1, 2000

The inauguration of a geological department for the mines of North Broken Hill Limited necessitated the provision of accurate plans and sections upon which geological facts and projections might be plotted.Unfortunately, the basic data were very inadequate. For the British Section, sill survey plans were available, but no regular stope plans. Filling surveys had been preserved for many stopes, but on innumerable pieces of tracing linen, without heights of any kind, and not altogether reliable (as indicated by the finding of very inconsistent duplicates). For the bulk of the old stopes no plans exist at all. The expenditure of much time and patience has resulted in the co-ordination of most of the existing stope data, but the British Section must for the rest of its life continue to have surprises in store, as has been the case for many years past. Manufacture and preservation of stope records has, of course, been on a sound footing during recent years. No reliable cross-sections of the British Section were available.The Marsh, Junction, and Junction North Sections have for the most part very poor data. In the North Section, level plans were fairly reliable, and cross sections of the lode made for ore reserve purposes have been preserved for quite a few years. No floor plans of stopes were kept, however, until a couple of years ago.Diamond Drill records vary in quality. Practically none exist for the Junction and Junction North Sections. Logs have been kept for the British Section drill holes, but are...

Jan 1, 1940

Performance driver trees or KPI trees are reasonably well-known tools for analysing performance in mining operations. However, the tools are often not user friendly. They may be technically correct but they are often clunky. This means they donÆt promote simple management decision-making and donÆt encourage businesses to make them an integrated part of optimising their operations. This paper describes a simple but effective driver tree process and tool that has been successfully implemented and used to aid decision making across a number of mining and processing operations. The important aspects of employing driver trees to assist in management of operations are to ensure that the chosen solution:includes a reporting solution, provides the bottom line impact of the performance indicators, automatically gathers the necessary data that reconciles with existing reports, and is built around a review process that fits with existing management processes. An adequate solution enables operators to identify where there are performance gaps and to quickly prioritise the urgency for addressing these issues. Two case studies are chosen to illustrate the critical success factors of implementing a performance driver tree solution. The first is a large, complex open pit operation. The driver trees, reporting and management processes were initially established for the mining and processing aspects of the operations. Once the initial solution was bedded down, a follow-up project was carried out to establish the equivalent solution for the support areas of the business. The final solution covered stand alone performance driver trees for mining, processing, engineering, maintenance, health and safety, human resources and finance. These individual driver trees were integrated into a total solution that showed how all of the identified KPIÆs impact profit and quantified the dollar impact of all variations. The reporting solution that was put in place automatically creates prioritised lists of variances for the business to address. The second case study is a performance diagnostic project where driver trees were used to assess where gaps in performance were occurring, and then to evaluate the impacts of proposed initiatives.

Jan 1, 2007

By Weller KR

Computer programs are described which help the metallurgist to process sample data from a plant survey; to carry out simple mass balance calculations; to present the results of circuit and equipment performance in convenient form; and to simulate the circuit response to changing operating conditions. The uses and limitations of these programs are explained by following through a case study of the sulphide flotation circuit at Cleveland Tin Ltd. The circuit was sampled, the data analysed, and some process inefficiencies established. Simulation calculations were then made to provide information on which to base decisions regarding possible circuit changes aimed at improving performance.

Jan 1, 1983

By Churchill J

A suite of software programs has been written to provide the field engineer or geologist with the capability to collect and store data directly into small, portable handheld computers. This allows the engineer and geologist to collect data in a more efficient manner as the data is collected in sequence and is verified at the time. Typical applications for this software include geological and geophysical logging, trucking surveys, mine surveying, condition monitoring, ventilation surveys and maintenance systems. The software allows the user to construct his own electronic notebook by structuring data input to the computer in a similar manner as is now done on pre-printed forms. The user can store all valid entry codes or numeric ranges in a dictionary and all data inputs made are validated against this dictionary. Once constructed the user may call the electronic data sheet into the unit and collect data which will be stored into the unit which has the memory capacity to record data for up to periods of 60 hours. The data can then be automatically transferred to mini/microcomputers for immediate analysis and report generation. The software may be used on a variety of handheld computers.However the generally rugged environments found in the mining industry limit the choices. In particular the authors have selected a unit weighing a little over one kilogram, which is rugged enough to fall off an underground survey vehicle, and survive when accidentally immersed in water,without losing data. This paper describes the software developments in detail. The project development work to produce this system has been funded by a grant from the Australian Mineral Industries Research Association and is supported by a number of large Australian mining companies.

Jan 1, 1986

DURING a period extending over about the last two and a half years, the performances of various types of rock drills in use at the mining department of the Zinc Corporation have been recorded as closely as possible. The main objective was the collection of sufficient data regarding internal water-feed hammer drills, when used for the same class of work as the older type reciprocating drill, to enable a decision to be formed on the following points:(1) Whether internal water-feed, hammer drills could efficiently perform the work previously carried out by reciprocating drills without excessive repair cost to the former.(2) If so, was it good policy commercially to eliminate the reciprocating type completely, writing these off together with the accompanying spares, accessories, and solid drill steel, and replacing with internal water-feed hammer drills, with lighter fittings, and the requisite amount of hollow drill steel.(3) What were the best types and makes of hammer drill for different classes of mining work(4) What was the economic aspect of the introduction of the principle of internal water feed to every type of machine throughout the mine.Prior to the strike of workers in May, 1919, Ingersoll-Rand E47 31-in. reciprocating drills had been used for stoping and for the major portion of driving, cross-cutting, and similar work. The accompanying columns and fittings were all 4t in. The drill steel used was solid octagon. Up to 1916 these machines were also used for winzing, after which time jackhamers were more successfully employed. These latter were of the usual types, varying in weight from 40 to' 46 Ib. Ingersoll BCR 430, Holman No. 2 spool valve, Sullivan DP33,. Waugh Clipper 55. These machines were all dry head; the drill steel was hollow hexagon, shanked.

Jan 1, 1923

The Telfer Gold Mine, owned and operated by Newcrest Mining and located in Western Australia, is currently being expanded. A new underground sublevel cave development is proposed along with an appreciable expansion of the open pit. The Telfer area is generally subject to low rainfall, however, during the wet season cyclonic events can result in sizable rain events, which have the potential to cause substantial inflow. In addition to this, during the first five years (nominal) of the mineÆs life, there is the potential for drainage paths between the pit and the underground mine via decommissioned underground workings which lie directly under the pit. After this initial five year period the pit floor will be mined out below the old workings and will therefore no longer connect to the underground, however cave breakthrough to the surface may start to occur thus providing another water path into the underground mine. To arrive at an optimum, safe solution for dewatering the mine that successfully addressed the above items, a rigorous risk analysis was included as an integral part of the design process. This involved the determination of the probability of events occurring and the consequences of these occurrences. This was compared against the cost of mitigation for the various events. This paper outlines the process by which a safe concept addressing all the issues relating to dewatering the proposed mine has been arrived at. This process included: Establishing the pit catchment areas. These were based on historical run-off data and took into account practical mitigation works. Establishing an Average Recurrence Interval (ARI) based on reference material and historical rainfall data. Utilising a standard approach based on Australian Rainfall and Run-off (ARR) to calculate pumping and storage requirements for the various catchments. Analysing the 20 years of recorded rainfall in the Telfer area to establish the duration, magnitude and sequence of events. This analysis assisted in determining the surface run-off coefficient. Establishing potential water storage areas and determining the risks associated with using particular storage options. Establishing the percolation rate through the cave zone. A degree of uncertainty regarding the percolation rate in the cave zone required that the consequences of using various percolation rates were considered to aid in establishing the rate which was adopted. Establishing preliminary concepts and determining the most economically viable concept. Conducting a risk assessment based on the principles outlined by Australian Rainfall and Run-off (ARR) to confirm that the appropriate Average Recurrence Interval (ARI) had been selected. A risk assessment was also conducted in accordance with client requirements. Establishing the optimum pump station sizes and storage capacities. Establishing the appropriate numbers of duty and standby equipment. By using the foregoing process, which included a number of stages of risk analyses, an optimum dewatering system concept was produced.

Jan 1, 2003

Disastrous earthquakes are a reality on the Australiancontinent. Unfortunately it has taken the fatal 1989 New-castle earthquake to demonstrate to all Australians that we do not reside on a "stable continent". While the world accepts the potential of plate tectonics and its associated plate margin earthquakes, particularly around the active Pacific Rim, the realisation of devastating intra-plate, or continental, earthquakes is only now beginning to take effect. The 1989 Newcastle earthquake provides many lessons on which to further fundamental earthquake research and the applications to the future welfare of human civilisation. To mitigate the earthquake hazard in relation to the devastation to life, property and industry, research must be undertaken with the resulting informa-tion to be included in the nation's disaster management programs. The earthquake hazard is everpresent in east-ern Australia and the major step in its quantification is a more realistic determination of earthquake risk estimates through an integrated study of seismology, engineering, insurance and sociology.

Jan 1, 1990

Solid EnergyÆs project evaluation process utilises a standard staged gate approach, with five levels leading ultimately to project execution (level 6). For a project to progress through each level, specific financial criteria need to be satisfied. Solid Energy primarily use value based (discounted cash flow) metrics to support investment decisions. Within this approach Solid Energy utilise a number risk-based techniques to quantify project uncertainty. This includes the use of risk-based probabilistic analysis using Monte Carlo simulation and probability-based scenario analysis. Figure 1 shows the net present value (NPV) cumulative probability. Project risks are identified through comprehensive risk workshops. The output of these workshops (list of key risks, ranges of uncertainty and probability of occurrence), is quantified within the financial models. Incorporating this risk information on a probabilistic basis allows an investment decision to be made with a robust knowledge of the range of possible project outcomes along with the likelihood (probability) of those outcomes occurring, for example 80 per cent confidence that the project value will be greater than NZ$10 M, 50 per cent confident it will be greater than NZ$50 M and ten per cent confident it will be greater than NZ$70 M. Incorporating risk implicitly into the financial analysis allows the business to easily evaluate/measure projects with different risk profiles. The detailed risk analysis does away with the complexity of arbitrary risk-based hurdle (discount) rates, as projects can be evaluated based on their specific risk characteristics. Whether a project will progress to the next level of investment and ultimately into implementation depends firstly on the value assessment in comparison with the associated risk/uncertainty, and secondly matching this with the businesses appetite for risk. At Solid Energy standard criteria are used for specific project evaluations, but in addition projects are considered on a portfolio or strategic basis also. Solid Energy attempts to maintain a mix of low risk (low value) projects with some high risk (high value) opportunities. The mix of projects must remain in line with the shareholdersÆ risk appetite. One of the keys to a successful investment decision is ensuring that the appropriate information is available to decision-makers so that they may proceed with a comprehensive understanding of the risks and impacts associated with the decision.

Jan 1, 2007

By P Cundall

Three-dimensional DEM (Distinct Element Method) simulations were conducted in order to examine the performance of screw conveyors, which are installed to transport bulk materials as parts of many industrial machines, including mining and construction machinery. To apply the DEM to the analysis of screw conveyors, we added a spiral object and cylinder objects, which correspond to the helical screw, the casing pipe, and the driving shaft of a screw conveyor. These objects are represented analytically to enhance the precision and efficiency when calculating the interaction between objects and particles. Simulations were conducted for some real applications: inclined and other types of screws, as well as the basic types (horizontal and vertical). Results were compared with previous work and empirical equations. It is concluded that this method is sufficiently well-developed and useful to analyse various kinds of screw conveyors.

Jan 1, 2000

By Lane G

This paper addresses project commissioning, that is, activities that culminate in the transfer of a project from the construction phase to routine plant operation. These activities should be initiated early in the engineering and design phase to ensure that the plant design is operator friendly and that construction is scheduled such that pre-operational testing and hand over to the owner occurs in a timely and cost-effective manner. For the purposes of this paper, commissioning includes all activities related to pre-operational testing, no-load testing, water commissioning, and ore commissioning. That is, all activities from construction completion to practical completion of the prime contract. This process is facilitated in numerous ways dependent on the nature of the project prime contract and the size of the project. For small lump sum projects, the contractor's responsibility may include all phases of commissioning to practical completion, whereas, a managing contractor on a complex multi-contract project may only be required to bring the project to mechanical completion and hand over to the owner for ore commissioning. Irrespective of the responsibilities, commissioning programs require careful planning, effective communication and detailed reporting. Unsuccessful

Jan 1, 1997

By Zamel GI

The utilisation of fossil fuels, including coal (of which Australia is a large producer and exporter) is a significant contributor to the emission of greenhouse gases. Methane gas, formed during the coalification process, is present in coal seams to varying levels depending on the rank and depth of the deposit. This gas usually escapes to the atmosphere during mining operations without prior conversion to C02 or utilisation as fuel. The quantity of methane released can represent from less than one percent to more than five percent of the carbon content of the coal mined. Per unit of carbon, methane has a greenhouse impact many times that of C02. The emission of uncombusted methane to the atmosphere can therefore represent a greenhouse impact of similar porportions to that of the CO2 formed by combusting the mined coal. However, greenhouse emissions from coal can be minimised by collecting the coal seam methane and converting it to water vapour and the less damaging form, CO2. If such conversion is carried out while performing useful work, the methane can further reduce greenhouse emissions by displacing other fossil fuels. Technology has been developed to allow coal seam methane gas to be economically collected in a pure form, uncontaminated with air. This pure methane can be used to supplement natural gas supplies, to generate power or for the production of chemicals or substitute transport fuels. By collecting and utilising coal seam methane, the greenhouse impact from the mining and use of coal can be minimised, with significant reductions possible in the case of gassy deposits.

Jan 1, 1989

By K Lee, K Fernando, S Rayner

Copper-gold ores have been technically difficult and uneconomical to process due to high consumptions of cyanide. Many copper oxide and sulphide minerals react with cyanide to form copper cyanide complexes, partly contributing to the high level of weak-acid dissociable cyanide in the tailings which is normally experienced during the processing of copper-gold ores. The cost for detoxification, if required for treating these tailings, would further inhibit the development of these copper-gold resources unless the cyanide used for leaching was recovered. Several technologies have been proposed to process copper-gold ores, aiming to recover copper as a co-product and cyanide for recycling in conjunction with the leaching process. A critical review of these processes reveals that a pre-concentration stage (solvent extraction or resin ion exchange) is required. Cyanide is recovered by the conventional Acidification-Volatilisation-Regeneration technique in most cases. A critical evaluation is also provided on technical aspects related to the use of Vitrokele Technology and a newly developed Elutech process in processing copper-gold ores, in particular with its application at May Day Mine.

Jan 1, 2000

Territory Iron has seen fit to revive the old Frances Creek iron ore mine some 30 years after it ceased operations in AustraliaÆs Northern Territory. The key to this revival has been the changes that have happened since market forces, infrastructure limitations and a cyclone combined to force its closure. As it breathes life into this old mine, the Company is serious about its responsibilities to its shareholders, to its workers, to local and regional communities and to the environment. This paper addresses how Territory Iron has approached technical, operational and regulatory issues that apply in Australia. Some insight may be gained into the myriad of tasks that mining companies face to revitalise an old mine. These tasks vary from employing the latest exploration tools, best practice drilling, sampling and modelling of orebodies, optimisation of pit designs and schedules, maximising product value by blending, optimising infrastructure usage and minimising capital and operating costs. All of this has to take cognisance of commercial, environmental and other issues including Native Title.

Jan 1, 2007

By R Valenta, J Owen, D Kemp, E Lebre, G Corder, J Thomas

Numerous recent analyses have shown that future demand for a broad range of critical commodities is unlikely to be met by new discoveries and recycling alone. The only practical alternative source to address this shortfall comes from orebodies which are currently either uneconomic or inaccessible. A common assumption is that a simple rise in commodity price will render these deposits economic. The mining industry has a long history of innovation allowing economic production from increasingly low grade and technically challenging orebodies. Industry “roadmaps” have been produced on a regular basis, with the aim of identifying future innovations which will allow this progression to continue. At the same time, there have been relatively few systematic analyses of the actual range of challenges facing undeveloped orebodies. The aim of this study is to analyse the mix of challenges faced by a group of undeveloped orebodies in order to better understand the relative importance and necessity of innovations applicable to the deposits, with the ultimate aim of determining the relative value and impact of possible innovations to the economic viability of those deposits. CITATION: Valenta, R, Lebre, E, Kemp, D, Owen, J, Corder, G and Thomas, J, 2018. Can a simple price-rise unlock complex copper orebodies?, in Proceedings Complex Orebodies Conference 2018, pp 71–72 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018