Search Documents

By Still RF

Sintering of lead and zinc concentrates is practised by Sulphide Corporation Pty. Limited to provide both desuiphurised lump sinter feed, for simultaneous reduction to zinc and lead in the Imperial Smelting Process blast furnace, and sulphur dioxide gas for sulphuric acid manufacture. From November, 1969 a 20 percent increase in production rate has been obtained through improvements in operating technique. A gradual increase in bed permeability was achieved by modifications to the feed mix conditioning equipment and by improving moisture control. However advantage could not be taken of the higher permeability to increase sulphur elimination because the hardness of the lump sinter decreased. Higher throughput, better quality sinter and more stable sintering conditions were however made possible by simultaneously: 1. reducing segregation and compaction in the sinter bed, by narrowing the discharge opening of the main layer feed hopper, 2. reducing the sizing of sinter returns to give a closer size spectrum of particles in the feed mix, and 3. increasing the sulphide sulphur content of the feed mix to give higher bed Temperatures.

Jan 1, 1972

By H Rose, T J. Sheer, M Dumka

Whenever rock is tipped from above, severe eruptions of airborne dust occur into the airways connected to tipping stations of rock passes (ore and waste) on the lower levels of a gold mine in the North West Province of South Africa. An investigation was undertaken to understand the nature of the physical phenomenon, in order to propose possible solutions. Accordingly, measurements were taken underground, involving the simultaneous logging at two levels of the transient pressures produced in the orepass by tipping from various levels. Two portable data loggers with associated transducers were custom-built for this purpose. Measurements were taken during a tipping program in which rock quantities and levels were controlled. Pressure pulses that are generated by the falling rock drive the airborne-dust eruptions. When tipping from a specified level, recorded pressure pulse waveforms were found to be repeatable on any given level, irrespective of the amount of rock falling, but measurements were conspicuously different on different levels. It was recognised that a pressure pulse is generated as the falling rock passes through the constricted region û a relatively narrow neck û at each tipping station. In passing through the constricted areas the mass of falling rock acts as a æleaky piston in a cylinderÆ and compresses the length of the air column in the orepass below that level. Once the rock has passed through the constriction, the pressure is released and this behaviour causes a regular train of pressure pulses that are separated by the time taken for the rock to move from one level to the next. Based on this physical understanding of the dust eruptions, a computational model has been developed that can reproduce all the main features of the measured phenomena. The model has been verified adequately against the measurements and can now form the basis for simulating a range of possible engineering solutions.

Jan 1, 2005

By Grace B, Cunningham D

The poor quality of bore waters available to the Australian mineral processing industry creates a climate for crystallization of calcium based scales. If ignored, calcite and/or gypsum buildup can cause loss of production and costly unscheduled maintenance. This paper discusses the factors which contribute to scale forma- tion, methods used to monitor buildup and preventative measures (mechanical and chemical) that can be used. A case history il- lustrates the value of using chemical antiscalants.

Jan 1, 1991

By Singh TN

Rampura-Agucha Zinc-Lead deposit is unique as it is reported for the first time in the gneissic terrain with a rich oregrade quality of early to middle Proterozoic of Bhilwara supracrustal belt in the Precambrian of Northwest India. These sulphide ores are mostly confined to the graphite bearing Quartzofelspathic gneisses with intermittent bands of Calc-Silicate granofels and amphibolite. The ore and country rock mineralogy and their textural features are indicative of highly metamorphosed deposit and further the presence of marmatite and monoclinic phyrrhotite revealed high temperature environment of deposition.The present paper deals with some of the ideas about the ore genesis and petrographics of the associated rocks for Rampura-Agucha Zinc-Lead deposits of Bhilwara District (Rajasthan).

Jan 1, 1990

This paper provides a financial perspective to the valuation of Australian resource companies and projects. Valuation exercises need, however, to be seen in the broader context of a thorough business appraisal, one that incorporates all disciplines employed in the resources industry. Fine tuning a discount rate or determining a particular capital structure is likely to be less important to valuation than an adequate understanding of industry dynamics and a company's likely performance in future years.

Jan 1, 1989

Australia, with its fast-growing economy and high standard of a~ living, has a high and rapidly increasing per capita consumption of energyIn total terms, Australia's energy requirements are doubling every 15 years, and among mature Western economies Australia ranks behind only Italy-and Japan in the rate of increase of energy consumption.The use of energy is often accepted as a yardstick of development and on this basis Australia might well congratulate itself on its high energy consumption. However, it is less well recognised that the resources absorbed in the production of energy represent a real cost to the* community, and that just as we strive for industrial efficiency or farm productivity we should strive for economy in the use of energy fuels.Australians spend annually an estimated ú500 million.on all forms of energy, a sum which represents about seven per cent of the Gross National Product. In all, energy production and distribution absorb the employment of more than 100,000 persons. In addition, the annual capital investment by.the oil industry amounts to some E55 millions, by the coal industry about ú12 millions, and by electrical and gas authorities some E108 millions, in total representing more than ten per cent of annual investment in other than private motor cars and housing,

Jan 1, 1962

By A J. MacDonald, M P. Raffield

The South Deep massive orebody consists of 20 to 30 m of payable conglomerates ranging in dip from 11¦ to 20¦ and at depths of between 2400 m and 3400 m. The mine design process selected a mining method with a proven record of application that could be adapted to overcome the inherent difficulties associated with the depth, thickness and structural influences of the South Deep orebody. A modified cut and fill mining method provides a concentrated and highly flexible method of extraction. An integrated destressing cut will enable the modification of the stress environment such that it is suitable for massive mining operations. The choice of backfill type and stoping width in the destressing cut ultimately determines the characteristics of the stress modification and, as such, is critical to the success of the cut and fill operation. This paper discusses the decision process undertaken to determine the optimum backfill type and stoping width combination in terms of, conditions in the destressing cut faces and in the massive mining environment. Numerical modelling has been extensively used to analyse various scenarios to aid in the decision process.

Jan 1, 1998

Resource rent tax is a form of taxation or royalty, which only become effective at such a time as a pre-determined rate of return has been achieved by an operation. The offshore petroleum industry in Australia is already subject to RRT as is the Roxby Downs (Olympic Dam) Mine in South Australia. Both the mining and petroleum taxation regimes in Papua New Guinea include a resource rent tax component called Additional Profits Tax (APT). The implications of the current form of Additional Profits Tax for shareholder cash returns are that the tax burden on the operation may suddenly increase at some stage in the life of the mine, if and when the threshold level of profitability for the tax to be triggered is exceeded. From that point in time onwards the cash return to the shareholders on the capital invested is greatly diminished. For mining companies in Papua New Guinea, the effective tax rate increases from 35% to 57.75% as a result of the onset of Additional Profits Tax. This tax rate penalty is so severe that there appears to be merit in considering the concept of managing profitability through time rather than purely maximising annual pre-tax profits as is currently the case in most mining operations. This would have the benefit of deferring or perhaps preventing altogether the onset of the tax. One possible method for the effective management of profitability is through the control of average mining grade by cutoff grade manipulation. Traditional cutoff grade theory has usually considered taxation as a direct cost at a fixed or variable percentage of annual profits. As a result of this most analyses are conducted on a pre-tax basis. If tax is included in analyses it is usually present as a time independent function of gross profit. Additional Profits Tax is both time and rate of return dependent and therefore not adequately accommodated by currently accepted cutoff grade theory. A review has been made of the effects of resource rent taxes on both the investment decision-making process as well as possible development and mining strategies which may be employed by mining companies faced with Additional Profits Tax. The review includes examples based on the structure of Additional Profits Tax which is levied in Papua New Guinea.

Jan 1, 1997

This paper deals with the evolution of present mechanised declining and orebody development practices at Kambalda, since their inception in 1969. Eight separate decline accesses have been established over the past eighteen years and to date some 175 kilometres of declining and lateral development has been achieved utilizing a wide range of mechanised development and mucking units. Improvements in-the range of equipment available, functionalization of the develop- ment tasks and the resultant changes to piecework contract structuring have all contributed to the improved performances achieved in this concept of mine development. Even though numerous development advance rate records have been established at Kambalda, an ongoing evaluation of changes to both drilling and mucking units is underway to further improve these development performance rates.

Jan 1, 1987

Before exploration programmes or minerals developments are formulated, a mining company ought to assess how capital can be returned if the project is successful. A fact not well appreciated by the minerals community is that it is often difficult to get money out of many Pacific Rim countries due to special foreign exchange controls or restrictions on dividend or capital repatriation. On top of this risk are factors such as creeping expropriation through administrative, fiscal, or corruption pressures; environmental regulations; terrorists; and organised labour and political activists. Political risk is much more than just expropriation or nationalisation.Political risk factors can make or break a project in many PacRim countries and just the cost of delays and negotiations can insidiously affect project economics. This unpalatable thought, however, can be readily addressed by either legal structuring e.g. offshore proceeds accounts, offset/back-to-back currency hedges, or political risk insurance for the equity as well as any subsequent project development debt.

Jan 1, 1990

Owing to the 'creeps' and consequent movements in the mines, followed by the recent fire in the southern workings, the whole of the orebody above the 800 ft. level is now very much crushed and broken. The same applies to the hanging wall or overwall coutrny, which has subsided towards the workings, so that for some years past all development work within the lode has had to be carried out with extreme care.The continual but slow subsidence of the overburden into the stopes necessitates a periodical renewal of all gangways in the lode, and, as the subsidence amounts to as much as 60 ft. in places, these new gangways must necessarily pass through the mullock-filling of old stopes in addition to broken ore. They at times pass into the broken ground of the hanging-wall for some distance, where the orebody has widened underneath by the original folding and puckering.

Jan 1, 1932

By S Logan, J Pu, J Milsom, G McDonald

Management of environmental issues is an integral part of the mine decommissioning process. In Queensland, miners must comply with environmental aspects of the Mineral Resources Act and Contaminated Land legislation. Successful decommissioning involves the integration of a final Plan of Operations, decommissioning report addressing the mineÆs commitments included in its Environmental Management Overview Strategy (EMOS), and Site Contamination Report for relinquishment of leases under the Contaminated Land Act (1991). Niugini MiningÆs Red Dome Mine is proceeding through the decommissioning process. This paper discusses the important environmental management issues including sampling programs, management of culturally significant areas, assessment of background concentrations of target analytes, the use of historical reviews and risk assessment techniques, the timing of works, and the remediation/management of large areas of impacted land. The importance of a clear communications plan between key stakeholders is also discussed.

Jan 1, 1998

By G H. Luttrell

The use of secondary desliming cyclones ahead of froth flotation cells to reject ultrafine (-45 ¦m) particles has become a popular option in the United States for preparing fine coal feeds for froth flotation circuits. In light of this popularity, several experimental studies have been performed at industrial plant sites to develop a better understanding of the impacts of ultrafine desliming on froth cell performance and, ultimately, overall plant performance. These studies included an evaluation of various circuit configurations incorporating different flotation technologies (conventional machines and column cells) as well as different dewatering systems (disc filters, screen-bowl centrifuges, and thermal dryers). The data obtained from these studies indicate that deslime circuits offer several important benefits including lower product ash, reduced product moisture, better froth handling characteristics, and lower capital and operating costs. In addition, case studies conducted as part of this investigation have been used to develop generic guidelines for how deslime circuits may be successfully applied to improve the overall profitability of fine coal flotation circuits for both the metallurgical and steam coal markets.

Jan 1, 2005

Electrochemical investigations of the flotation of sulphide minerals are re- viewed. Flotation with thiol collectors is interpreted in terms of a "mixed poten- tial" model in which the process leading to hydrophobicity is the anodic oxidation of the collector at the mineral surface and this is driven by the cathodic reduc- tion of oxygen. Electrochemical studies have identified the products of anodic oxidation as chemisorbed collector, metal collector compounds, and dithiolates; the products formed in each situation depend on the collector used, the mineral under study, and the pretreatment of the mineral surface. Investigations on galena, pyrite, and chalcocite are discussed. Electrochemical and x-ray photoelectron spectroscopic studies have been used to determine the products of surface oxi- dation of sulphide minerals in order to elucidate the mechanism of collectorless flotation. The mixed potential mechanism allows consideration to be made of the ways in which flotation of sulphides with thiols can be inhibited. Examples of depressant action are presented. The relevance of electrochemical investi- gations to practical flotation is Discussed.

Jan 1, 1984

This paper provides a brief fundamental insight regarding the fabric media concept for liquor filtration. The subject matter will be of interest to metallurgists and engineers with professional responsibility for world class design of solid liquid separation processes and efficient lowest cost operation of existing mineral process plant. Avocet Mining commissioned the worldÆs first mineral liquor clarification process incorporating a fabric media liquor filter at their Lanut gold mine in Sulawesi, in 2004 with design consulting provided by the Australian company SLS Technology Pty Ltd. Development of the technology continues with applied research focused on selecting textile parameters to apply filtration to a wider range of particle and contaminant types, higher solids concentrations, and different process liquors. Liquor filtration with the Fabric Media technology offers an array of attractive benefits. For Avocet Mining, filtration of pregnant liquor directly from the heap leach pad has enabled removal of the sediment pond and sand filters from the traditional process flow sheet, thus providing significant cost and installation time savings. Avocet Mining has recently expressed confidence in the technology indicating selection preference of the technology for the expansion at Lanut and for a new project. The application design window for the Fabric Media concept is extremely flexible with the technology now successfully applied to many different liquor chemistries and application objectives around the world. Potential cost savings for solid liquid separation process plant, such as counter current decantation circuits, clarifier vessels and thickener tanks can be calculated from laboratory measurements or pilot plant demonstrations.

Jan 1, 2008

The treatment of slimes has of late years been the chief difficulty in connection with cyanide work, in which much time and money has been spent in endeavouring to find a practical solution of this problem.The processes at present in use are:-1. Filter pressing, as practised in Western Australia.2. Decantation, as practised in South Africa.Filter pressing after apitation affords a ready and efficient means of separating the gold bearing solution from the slimes and admits a perfect washing thus ensuring a high extraction but the very high working costs forbids its application except on high grade material, the chief items being the necessary large amount of labour, compressed air, and general upkeep, none of which can be materially reduced. The decantation method has the ad vantage of low working cost but on the other hand the low extraction obtained, due to imperfect washing, the length of time occupied in' the treatment, and the enormous bulk of solutions to be handled, are serious disadvantages.In either process it is absolutely necessary to obtain a perfectly clean solution before starting the gold precipitation by zinc, which is a source of much trouble. Also the high first cost of installing either plant is such that they can only be adopted on mines with very large working capital.

Jan 1, 1903

This paper outlines the mechanism of Stress Corrosion Cracking (SCC) and how it can cause premature failure of rock bolts. SCC occurs due to the progressive development and growth of cracks in the surface of a metal, and it is caused by the combined effects of stress and a corrosive environment affecting susceptible metals and alloys. It can occur in most metals including stainless steel. It is not a new phenomenon, but its effect on rock bolts has only been recognised recently.Rock bolt failures caused by SCC appear to be brittle failures which occur at less than the ultimate tensile strength of the bolt. In the mining industry, SCC failures of rock bolts can occur a few months, or after many years of exposure to stress and a corrosive environment. If SCC of rock bolts is suspected, then the rock bolts should be examined by a metallurgist, and steps should be taken to reduce the problem.

Jan 1, 1998

By Kershaw M. G

At the Risdon plant of the Electrolytic Zinc Company of Australasia Limited, impurities toxic to the electrolytic production of zinc metal, notably arsenic and antimony, have traditionally been coprecipitated when precipitating iron as ferric hydroxide. With the development of a new lead/zinc mine at Elura, New South Wales, it was anticipated that the concentration of impurities, particularly arsenic, in the zinc sulphide concentrates treated at Risdon would increase. This suggested that an increase in the capacity of the iron purification step in the Risdon plant would be required to cope with the higher input of these impurities.Laboratory investigations showed that the additional capacity would be achieved, either by a large increase in the amount of iron used as the "collector" in the process, or by a two-stage process. The latter approach was preferred as a increase in the amount of iron precipitated would lead to much higher operating costs and overloading of the existing equipment.In the two stage procedure, acidic iron bearing solution is added to solution feeding the first stage and most of the arsenic removed from solution when iron is precipitated from solution by neutralisation with limestone. Mter separation of the precipitated solids, acidic iron bearing solution is added to the solution, and remaining arsenic removed almost completely following neutralisation by limestone.This paper describes the laboratory and pilot plant results and the plant modifications required. Abrief account is also given of the operator training and acceptance in the use of the digital control facilities installed in the new plant.The new plant is working well and good solution purity is being maintained despite a substantial increase in the concentration of impurities in the raw materials.

Jan 1, 1990

By R Terracciano, J Schneider

Willemite (Zn2SiO4) is one of the main zinc carriers in several Neoproterozoic carbonate-hosted non-sulfide deposits ofNamibia and Zambia. Willemite commonly replaces sphalerite, but it may also replace the carbonate host rocks. Fluid inclusions, cathodoluminescence petrography and trace element geochemistry are crucial to distinguish between hypogene, high temperature and low temperature (possibly) supergene willemites. A global period of willemite mineralisation, extending from Cambrian to Lower Ordovician has been proposed for the southern hemisphere. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By Streichfuss M, KeBler H-W, Burgwinkel P

This paper describes the design of an expert system used as a part of a diagnostic system for diesel hydraulic drives. A PC-based diagnostic system ruDi (KeBler and Burgwinkel, 1993) was developed to minimise the time for diagnosis and repair work of vehicles with diesel hydraulic drives used in the mining industry. One part of ruDi is an expert system that helps to locate errors in any of a vehicle's subsystems, and supports technicians in removing the cause of a malfunction. Apart from the standard knowledge of diesel engines and hydraulic transmissions, the expert system supports the interpretation of the data obtained during sophisticated engine analysis tests such as high-resolution speed analysis or high-pressure analysis of the diesel injection system. The expert system is designed to diagnose various vehicles of the same type. Data for each vehicle is stored separately allowing checks to be carried out individually for each machine. An additional feature of this system is a database interface to a Maintenance Planning and Control System (MPCS) that allows an automatic generation of work orders for the defects found during the expert system sessions.

Jan 1, 1995