Search Documents

By Harris HR

This paper documents the selection, installation and performance of six, seventeen cubic metre, Dorr-Oliver flotation cells for primary zinc flotation at the North Mine in Broken Hill. The cells were installed to replace fifty, small cells, and despite initial design problems, have per- formed satisfactorily.

Jan 1, 1988

By Piga P, Sammarco O

Ventilation and the environmental climate in the Campiano mine is the subject of this re- search. The mine is located in Southern Tuscany (Central Italy), a region where geothermal gra- dients are very high (three times the average gradient of the earth). The research produced interesting indications as to the influence of surface climatic conditions on the environmental parameters inside the mine. A close correlation has been found between dry-bulb temperature and humidity ratio of the air in the mine for dif- ferent metereological conditions and for differ- ent mass flow rate values. Variations in air enthalpy, caused only by the heat exchange with the rock walls during the flowing of the air through the mine, depends on the surface temperature values. Statistical analyses have been used to ex- press air enthalpy variations on surface tempe- ratures, on the variations of the humidity ratio that the air undergoes inside the mine and on the mass flora rate. The application in practice of the results will permit the identification of correct mea- sures to be adopted so that optimal microcli- matic conditions are produced in the mine.

Jan 1, 1986

By Q Qian, M Karakus, J Wang, N Melkoumian, D Goodchild, Q Sui, C Wang

Probabilistic analysis is widely used in slope stability assessment because of its capability to take into account uncertainties associated with geotechnical parameters. There are, however, still many unresolved practical issues to the application of the method. One of these issues is the integration of assessments when multiple sets of fractures are considered for the entire slope. In the present study, this issue is addressed within the framework of Monte Carlo simulation. Probability of failure for pairs of fracture sets are assessed independently and the final assessment of the probability of failure for the entire slope is done using conditional probabilities. Prominent Hill open pit, in particular, the problematic fresh Bulldog shale formation, was used as a case study to test the method proposed. The SWEDGE program of the RocScience software package was used for the analysis.

Sep 26, 2011

By Stille H

The choice between drill and blast and mechanical boring methods is often not obvious. There are several factors which may have a de- cisive influence on this choice, such as the geometry and length of the tunnel, site con- ditions and borability of the rock. Both the un- confined compression strength and the joint dis- tance have a considerable influence on the net penetration rate. Site conditions, rock quality and water conditions influence the utilization of the tunnel boring machine. The drill and blast method is normally less sensitive to devi- ations from assumed ground conditions.

Jan 1, 1987

By Biswas AK, Hayes P

During the reduction of iron oxide pellets in the blast furnace it has been found that catastrophic swelling (up to 300% volume increase) can occur. Although the burden preparation conditions can be designed to avoid this phenomenon the exact reason and mechanism of the swelling has yet to be clearly identified. Swelling of the burden is undesirable since it reduces the interparticulate voidage in the blast furnace thus reducing gas flow through the stack resulting in low production rates of iron. The present study differs significantly from previous experiments in that reduction is carried out on single crystals of wustite thus the problems of control of gas composition and specimen preparation are minimised. The microstructures formed on reduction have been examined by optical and scanning microscopy. Pure wustite and wustite doped with various levels of CaO have been examined after reduction in controlled CO-CO 2 gas mixtures at 968¦C. The catastrophic swelling on reduction coincides with the formation of an unusually open iron structure in which the iron appears as whiskers or needles as previously reported. The spacing and thickness of the needles are shown to vary with impurity content and gas composition. Metallographic examination has shown in addition, however, that the whiskers do not necessarily constitute the only product form of the iron produced and in CaO containing wustites with less than - 2% CaO there is a transition from needle growth to porous growth of iron. Thus the % swelling of the oxide particles is dependent on the initial size of the oxide grains. Samples of FeO - 10% CaO exhibited a previously unreported product inorphology associated with the nucleation of 2CaO.Fe203.

Jan 1, 1980

By Harraway DH, Tanner AC

The various circuits tried!at Mount.Isa Mines during the period 1959-1963 to improve the differential%f lotation of galena and sphalerite are reported. The benefits and disadvantages of 'the various circuits are discussed. An analysis of ore charao-beris;ics.and their effect on flotation is followed by the d~soription,of a proposed".cirouit in the process of install-ation.

Jan 1, 1963

By D J. Clark, S Hewson, T Li

Cadia Hill Pit is a gold copper porphyry deposit hosted in monzonite. The pit slope design is primarily based on structural controls related to faults and shears with largely massive rock masses between the structures. The slope design attempts to achieve an optimum configuration at a bench to overall scale, considering economics and safety implications against the geotechnical and structural conditions. To date the slopes have been mined at interramp angles of up to 60¦ over heights of 120 m. Limited slope and batter failures that have occurred are structurally controlled and occur rapidly. The pit-mining schedule requires concurrent mining of part of the final pit walls and the progressive interim cutbacks. Engineering and operational solutions to hazard reduction and risk management issues have been implemented wherever viable to æengineerÆ out the hazard and mitigate the risks. However, comprehensive management plans and operating procedures have also played a vital role. This paper details the management plan and the operating procedures that have been developed and implemented to mitigate the risks associated with rock falls.

Jan 1, 2003

I am very grateful to have the honor of delivering this Key- note Speech to all of you here today, to the Chairman Mr Cope- man, and to all the organisers. As you heard, I was mainly involved for a very long time in the purchase of iron and steel raw materials for Nippon Steel Corporation. Today, however, I would like to talk to you about a much wider issue, namely, how the Japanese steel industry is going to change towards the 21st Century, and what will be the main technical innovations and trends behind those changes. I will also mention the effect that the changes are likely to have on the procurement of raw Materials.

Jan 1, 1988

By Brant BA, Lewandowski R, Trendle M, Haughton D

There is a vast amount of geotechnical data, which can be obtained during exploration programs at new and existing mine sites. Additional information on the performance of the in-situ rock mass can be obtained from bore cores, which are usually only geologically logged and then stored. A computer based data management system for storage and retrieval of geotechnical data has been developed to access and manipulate such data.

Jan 1, 1983

By Rongqing Q, Tiancong Z, Yiyuan L

The influence of pulp density, ferric ion concentration and particle size on the tank bioleaching of two kinds of refractory gold concentrates are discussed. The chemistry and mechanism of the bioleaching process are also presented. The relationship between oxidation of sulphides, liberation of enclosed gold and gold cyanidation are discussed. The consumption of NaCN could be reduced by alkaline treatment of bioleached residues prior to Cyanidation.

Jan 1, 1992

By D Lau

Traditionally X-ray diffraction (XRD) has not been significantly used by the cultural heritage sector, as the most commonly used technique, X-ray powder diffraction (XRPD), requires sample removal from the artwork or artefact, followed by grinding of the sample to a fine powder. With the development of micro-X-ray diffraction (micro-XRD) and other associated advances, non-destructive, in situ analysis of crystalline pigments on micro-areas of paintings and artefacts has become possible. This is illustrated with the application of this technique to the in situ analysis of propriety paints, paint cross-sections and small paintings. However, workers have noted that XRD can be insufficiently sensitive with pigment mixtures, due to matrix effects. This study obtained X-ray diffractograms of 17 single pigment preparations and determined relative amounts of crystalline content. The purity of single pigments was compared with Joint Committee on Powder Diffraction Standards (JCPDS) database diffractograms. The impact of pigments with high X-ray absorption coefficients on the detection limits of pigments with low X-ray absorption coefficients was further investigated by building on work done with the chromium oxide-zinc oxide series with the preparation of a second series of binary mixtures of zinc oxide (which has a high absorption coefficient and is almost fully crystalline) and ultramarine blue, which has a lower absorption coefficient but which is more crystalline. Semi-quantitative analysis, where baseline and absorption factor corrections are made, confirm detection limits as low as five per cent for chromium oxide and ultramarine blue when in a binary matrix with zinc oxide. However, this type of analysis is very time consuming. So in order to theoretically simulate issues that will be encountered with binary pigment mixtures, the single phase diffractograms were used to theoretically investigate the matrix effects of the three white pigments with the various coloured pigments. This illustrated that detection limits can be as low as five per cent or in non-ideal conditions, such as with partial peak clashes or where there are large differences in relative peak intensity, as high as 50 per cent. These results have significant implications for the analysis of painted surfaces on artworks or artefacts. It has been demonstrated that ideally this method is more suited to the investigation of surfaces where there is minimal mixing of pigments or where there is not a significant difference between the absorption coefficients of the mixed pigments.

Jan 1, 2008

An investigation was performed to determine the sequence of events which caused the 1987 surface subsidence and related damage to several homes in Walker County, Alabama, USA (see Figure 1). Surface affects compared to mine maps indicated the subsidence to be mine related. However, two coal seams had been worked under this area. The upper seam, the American seam ranged from 250 to 280 feet beneath the surface in the area in question. It was mined-out before 1955 by room-and-pillar method leaving in place narrow-long pillars to support the overburden strata, and abandoned in 1955. The lower seam, the Mary Lee seam, ranged from 650 to 700 feet beneath the surface. The Mary Lee seam had been abandoned in 1966 and subsequently became flooded. The dewatering of the Mary Lee seam workings in 1986 caused the submerged pillars to be exposed to the atmosphere. Due to multiple seam mining and the fact that workings had been inundated then dewatered, a subsurface investigation ensued to determine the sequence and ultimate cause of surface subsidence. Core sample tests with fracture analysis in conjunction with "down-the-hole" TV camera inspections provided necessary information to determine that the subsidence started in the lower seam and progressed through the upper coal seam to the surface. Evidence from the investigation program established that dewatering of the lower seam workings caused the marginally stable support pillars and the roof to collapse. This failure triggered additional subsidence in the upper seam which broadened the area of the influence at the surface.

Jan 1, 1992

By M Noppe, I Glacken

There are many critical nodes along the mine value chain, from orebody to mineral product, and inter-disciplinary input is required to analyse the variability and uncertainty at each node in order to identify and mitigate areas of risk. Mining differs from many other industries in that the variability in the product is dictated largely by the inherent nature of the input material (the orebody). The true characteristics, including the variability of the orebody, are never known exactly and are instead based on estimates derived from sample data. A further difference is that bottom-line gains are largely controlled by world commodity prices, which can vary with time, rather than by local supply and demand issues. Methods for identifying, reporting and responding to this inherently variable raw material are discussed. These include analytical and reporting methods, equipment and software, risk analysis and reality checks (eg reconciliation). Sampling results, mineral resource and ore reserve estimates and economic assumptions are a function of the variability of the orebody. Risk quantification should be expressed as a level of confidence, which takes into account the scale or period over which the risk is being assessed (life-of-mine, annual or shorter production periods) and should convey the likelihood, severity and consequence of occurrence of a given event. The future generation of mining specialists needs to understand the entire mine value chain to better manage risks and maximise mine dollar-value.

Jan 1, 2002

By Bradley AJ

Hamersley Iron Pty. Limited mines and pro cesses iron ore from two orebodies at Tom Price and Paraburdoo, situated in the North West of Western Australia. Conventional open pit mining methods are used at both sites in that material is drilled and blasted in benches, loaded by shovels and hauled to the Primary Crushers or dumped on waste or low grade material stockpiles. The present drilling fleet, consisting of eight high capacity Bucyrus Erie Rotary drills has evolved from an initial fleet of a large number of small percussion rigs. There are significant physical differences between the ore types encountered at both mines which nec- essitate the drilling of smaller diameter blast holes at Paraburdoo than those at Tom Price. The drilling practice at each site is dis- cussed, with examples of performance achieve- ments under varying drilling conditions.

Jan 1, 1978

The mine planning and operational aspects of applying Continuous Surface Miner (CSM) technology to Australian coal strip and open cut mines is investigated for both existing and planned deposits. CSM produc- tivity as a function of geomechanical properties, formation thickness, mechanical availability and in-pit physical constraints, are considered. Productivity and operational costs are derived from current production machines and from first principles.

Jan 1, 1989

Mining, like most other businesses, is based upon capital assets; and the primary cap- ital of any mining company is its ore reserve. A company's survival and growth is, thus, dep- endent upon its ability to replace, increase, redistribute and to diversify its ore reserves. A Kennecott executive addressing a group of geologists in 1957 stated, "Management expects a geologist to find ore! That is the primary objective and the justification of the geologist in the minerals industry. There is no other function that we can rationalize." This is, however, a restricted point of view, and one which I an sure is not fully shared by mining executives or mine operators at the present time. Ore reserves are 'made' as well as 'found' and the geologist contributes to this process. A mining geologist engages in activity in- volving the study of geology in connection with the total mining operation. His major task is the adaption of geological knowledge of ore de- posits and rock behaviour to mining needs, and the application of principles of the science of geology to specific problems of finding, develop- ing and extracting of ore bodies.

Jan 1, 1975

By E S. Souza, H Delboni Jr, M F. Calixto

This paper aims at presenting the results of laboratory, pilot plant and simulation studies for the design of the grinding circuit for the beneficiation of compact itabirites from the Conceitpo mine. Two alternatives were investigated, both utilising the current crushing circuit up to tertiary crushing. Under alternative #1, quaternary crushing was considered to produce the feed of the ball mill; under alternative #2, high pressure grinding rolls were selected to prepare the ball mill circuit feed. Pilot scale studies pointed towards the use of high pressure grinding rolls (HPGR). The circuit design was based on a throughput of 720 t/h, representing a nominal solids flow rate of 600 t/h, considering a design factor of 1.2, and P80 of 95 ¦m.

Jan 1, 2007

The South Comet mine is an underground silver-lead-zinc mine located on the West Coast of Tasmania with an annual production in the order of 35 000 tonne per year. All ore mined is shipped to the Rosebery mill by road, a distance of 17 km.

Jan 1, 1993

By Qixiang Y

The strength of coal mass saturated with gas is an essential parameter in studying the mechanism of gas and coal outburst,and its prediction method. Up to now, there has not been a method for determining the strength of coal mass saturated with gas.This paper describes a new method whereby the strength of in-situ coal mass can be determined and stored continuously and automatically. The simulation results obtained in the laboratory indicate that the new method allows a fast, reliable, inexpensive and convenient determination of the strength of coal mass.

Jan 1, 1992

The issue of flyrock is critical to the operation of all mineral extraction sites that use blasting. This paper takes a risk-based approach to identifying, analysing and managing the flyrock hazard. The basic cause of flyrock generation is a mismatch between the energy available and the work to be done. It should be noted that the energy available depends on the charge confinement. This mismatch can be caused by an abrupt decrease in rock resistance (geological weaknesses), overcharging, inadequate delays between holes and rows, inappropriate blast design and inaccurate drilling. The mismatch can come about from two sides; either too much energy (charge) for a fixed burden (work to be done), or insufficient burden (work to be done) for a fixed charge. The main mechanisms of flyrock generation are rifling, cratering, face bursting and secondary blasting. Each source mechanism has different characteristics in terms of vulnerable locations and each requires different control measures. However, all controls require a high level of quality control and assurance. A range of different approaches for managing flyrock risk and determining blast clearance zone dimensions are presented. A prescriptive consequence-based approach is discussed. A conventional risk matrix based approach is outlined with some innovation regarding controls rating and uncertainty ratings. A published semi-empirical approach is discussed. Two examples of quantitative flyrock risk analysis are presented; one involves bench blasting based on a published paper and the second is a cratering example developed by the author based on consulting projects. Finally, a stochastic approach based on published work is presented which simulates cratering superimposed on face bursting mechanisms. Also, a stochastic analysis undertaken by the author of the cratering example is presented. Effective blast emission management is required for two reasons; firstly to reduce and/or eliminate safety risks and secondly to manage public perception of blasting risks such as flyrock. The conclusion of the current research is that the wild flyrock risk can be estimated using existing techniques. Furthermore, both qualitative and quantitative risk management methods as discussed in this paper can be used for flyrock management for a given blasting situation. A combination of both is considered to be best practice.

Jan 1, 2007