Search Documents

By I P. W Chau

Construction of twin stacked railway tunnels through mixed ground conditions in the heavily populated urban environment of Hong Kong, including tunnelling in poor ground conditions, with low cover and under or adjacent to sensitive structures with minimal impact was the challenge presented by the tunnelling section of the Kowloon Southern Link project. This paper details how twin 1.1 km tunnels of 7.0 m internal diameter were driven by Mixshield tunnel boring machine (TBM) in mixed ground through one of the exclusive shopping and hotel districts in Kowloon. The paper addresses the challenges required to be considered and managed for the success of the project, including ground conditions, TBM selection, Mixshield TBM operation, settlement monitoring and control, ground- borne noise and vibration, proximity to utilities, buildings, roads and operating railways.

Jan 1, 2008

This paper comprises a discussion of standards for comparing conditions in mines, of methods for measuring the flow of air, of a comparison of fan performances, and the application of these matters to mines in Western Australia.UNDERGROUND CONDITIONSIn approaching the question of mine ventilation one naturally searches for some standard by which to measure the conditions in a mine.There are several clauses in the Mines Regulation Act defining the conditions which are permitted. The quantity of CO2 is limited to 0·25 by volume, but the estimation of CO2 involves a chemical determination and is not suited for general use in a mine.The maximum temperature is fixed at 87 0 F. (dry bulb), and at 80° (wet bulb). The reading of temperature is easily done in the working places, and this is a very valuable and practical test of the conditions in a mine.The wet bulb temperature is probably the most important factor in determining working conditions. It is obvious that human life cannot be sustained for any appreciable period if the wet bulb temperature is above blood heat (about 97°F.). In places where the wet bulb temperature is 90°F. there is danger of heat stroke.In places where the air in a mine is still, the wet bulb temperature rises to a value close to the rock temperature.Adequate ventilation cools the workings by transference of heat from the rock to the air stream, and the temperature...

Jan 1, 1939

By Anderson JDC

Opencast Lignite Mining requires topwall strata of seams to be fully depleted and footwall aquifers sufficiently depressurized. To prevent a spread of the cone of depression into protected wetlands some distance away, alternatives had been investigated such as closing water works, underground slurry wall barriers and recharge by infiltration. As a result of these investigations, the infiltration method has been chosen and in a first phase during the next decade it will utilize as much as 55 x 106 m3/year. Using this approach, the survival of the wet lands is assured.

Jan 1, 1988

Consideration is given to the factors affecting raceway activity and the hearth design of a zinc-lead blast furnace. Results of measurements made on operating furnaces are given and comparisons are made with published data both from operating iron blast furnaces and from dynamic models of the zinc-lead blast furnace. Indication is given of the methods used for assembly of the relevant information into the specification of a commercial furnace design. A discussion on the comparative merits of furnaces of circular and essentially rectangular plan is given based on the concepts explained in the paper.

Jan 1, 1981

By S F. Simmons, A McOnie, J L. Mauk

Three cross sections, 200 m apart, display the distribution of indicator hydrothermal minerals across the Empire zone of the Golden Cross epithermal Au-Ag deposit, Waihi, New Zealand. These minerals are used to interpret the temperature and composition of hydrothermal fluids. The distribution of interstratified illite-montmorillonite and illite indicate that temperatures ranged from 140 to >220¦C, with temperatures above 220¦C predominating. The mineral assemblage of quartz-adularia-chlorite-illite-calcite-pyrite envelops the Empire vein system and stockwork, and reflects formation from an alkali chloride water whereas the mineral assemblage of replacement calcite-interstratified illite û montmorillonite-kaolinite forms a carapace and reflects formation from a CO2-rich steam-heated water. Alkali chloride waters appear responsible for the epithermal Au-Ag mineralisation.

Jan 1, 1995

In south-eastern King Island, sediments and lavas of possible Upper Proterozoic to Lower Cambrian age have been intruded by Lower Carboniferous granitic rocks.Within the contact aureole of the Bold Head adamellite north of Grassy the sediments and lavas have been metamorphosed to hornblende hornfels facies grade. The thermal gradient within the contact aureole was small, as the hornfelses exhibit no mineral zoning over a distance of 700 ft from the adamellite.Skarns occur both within the adamellite near its contact with the country rocks, and within the country rocks as partial replacements of three dolomitic limestone horizons. The latter type, the exoskarns, commonly have an andradite-salite mineralogy and carry economic concentrations of scheelite. These resulted from the replacement of carbonate beds due to both diffusion and infiltration metasomatism. Silica, tungsten, minor sulphides, and water were introduced from the adamellite, while aluminium and iron diffused from the enclosing pelitic sediments. Calcium released during marble replacement countered the loss of iron and aluminium in the pelitic hornfelses transforming them to diopside-rich rocks.Endoskarns within the adamellite are the result of two way diffusion across the contact; calcium, aluminium, and iron diffused from sediment to adamellite as silica, potassium, sodium, and water diffused from adamellite to the sediments. From estimates of the lithostatic pressure and mole fraction of CO2, the mineral assemblages of the hornfelses imply that the temperature of metamorphism lay between 530° and 710°C. This temperature range is in good agreement with minimum temperatures, between 610° and 710°C, for the recrystallization of the marbles of the contact aureole, calculated from the determinations of the solid solution of the magnesite molecule in calcite.

Jan 1, 1971

By Quast K. B

Laboratory batch rod and ball milling tests were conducted on samples of Heavy Medium Separator (HMS) sinks from Renison Tin Limited. The product size distributions for this heterogeneous material were very different to similarly sized homogenous material previously reported by the authors. The effects of pulp density on product size distributions were only evident at pulp densities greater than 80 per cent solids. At high solids density, the major weight distribution product peak fell and broadened indicating less efficient breakage, particularly for rod milling. Tin distribution in the ground products was also affected by pUlp density, and there was always less cumulative per cent tin than cumulative per cent weight, ie there was no tendency for cassiterite to slime down to 10/lm.

Jan 1, 1995

By Simmons SF, Fleming J

Alteration and mineralisation at the Island Copper deposit is related to the intrusion of Early Jurassic quartz feldspar porphyry dykes into surrounding comagmatic Bonanza volcanic rocks. The pyrophyllite alteration zone forms an upward flaring cone, largely hosted within a breccia body that c ross-cuts the Cu, Mo, and Au-rich ore shell. This alteration zone contains pyrophyllite, dumortierite and diaspore and resembles alteration occurring in some high-sulfidation deposits, but which is barren. Fluid mineral equilibria and fluid inclusion studies indicate formation at approximately 300 ¦C from fluids dominated by steam and gases. These fluids appear highly acidic, but sulfur poor, leading to extreme base leaching within the breccia body and surrounding rocks.

Jan 1, 1995

By B, J Bianchini, N Voermann, C Crowe

Operational and economic imperatives in the metallurgical industry have led to numerous advancements in furnace design. Modern furnaces provide high production rates, high percentage online time, long campaign life between rebuilds and safe operating conditions. Current trends for maximising plant efficiency include increasing the throughput of existing process vessels (often by a factor of two or more) and the use of newer, highly intense processes. In both instances, the process intensity results in the generation of higher heat fluxes to the crucible walls. High-intensity furnace operation with the objectives mentioned above has become possible with the following furnace design features: Strong sidewall cooling systems, using copper coolers, to accommodate the high heat fluxes encountered while protecting the crucible refractories; Robust, spring-loaded furnace horizontal and vertical binding systems which maintain tight brick joints through-out all stages of operation; and Well-designed, intensely cooled tapholes for metal, matte and slag. The integration of these features along with properly selected refractories, appropriate instrumentation systems and efficient water-cooling systems is also highly critical. These design features have been successfully implemented in electric smelting furnaces, flash smelting and converting furnaces (Outokumpu and INCO types) and lance injection furnaces (Mitsubishi, Ausmelt and Isasmelt types). This paper will discuss design aspects and operating results for several installations.

Jan 1, 2002

By M Danišík

Two drill core samples of haematite/goethite from the Robe River (Western Australia) channel iron ore deposits (CID) were dated using (U-Th)/He methods in order to constrain the timing of iron oxide formation and thereby provide a temporal context for CID genesis. (U-Th)/He ages (He ages) from these samples range from the late Oligocene to Late Miocene and despite a high degree of scatter, they corroborate relationships expected from the internal ooidal stratigraphy: For individual ooids, the ages from haematitic core are older than or indistinguishable from the ages of the surrounding goethitic cortex. The goethitic cortices are, in turn, older than the ferruginised wood fragments recovered from the cementing goethitic matrix.The data suggest the following succession of ore formation phases:• Haematitic cores in ooids of both samples formed in the Early to Middle Miocene.• Goethitic cortices of both samples formed in the late Middle to early Late Miocene. This appears to be the age of goethite cortex formation regardless of depth in the core, which does not support the top-down infill model, genetic model proposed by Heim et al (2006).• Wood fragments form a prominent component of the matrix and were ferruginised during the Late Miocene. Thus the data suggest that the unique environmental conditions for the CID formation existed during the Miocene.A methodological implication of this study is that the temperature utilised for He-extraction from iron oxides has a critical impact on the mobility of parent nuclides. The typical ~1100°C laser heating used for crystalline minerals like apatite or zircon induces loss of U and Th and results in erroneously old ages.

Jul 11, 2011

By Biao Q, Mizuta Y

Thermal constants such as thermal con- ductivity and thermal diffusivity of rock and coefficient of heat transfer of airway wall are the most important characteristic values which decide accuracy of prediction calcula- tion. However, quality of rock is not homoge- neous and water content in rock varies with location and so, a method for in-situ measure- ment of thermal constants must be taken in. The method developed by us is to measure in- situ rock temperatures at two different depths from airway wall. It is simple and we found its accuracy is good enough in the engineering Sense.

Jan 1, 1988

Ferromanganese metasediments in the immediate vicinity of the Mid-Proterozoic Broken Hill Pb-Zn-Ag lodes, have undergone high grade (upper amphibolite facies) metamorphism,to form Mn-pyroxenoid (rhodonite,pyroxmangite) and garnet-rich lithologies. Such lithologies bear compositional (bulk rock,rare earth element)and morphological similarities to recent and ancient ferromanganese hydrothermal sediments of the Pacific.The non-metasomatic,stratiform garnetites are predominantly composed of magnesia-rich, calcium-poor almandine spessartine and quartz, which possess a bulk chemistry comparable to alumina-rich ferrommanganese oxide deposits of the Pacific. Such sediments are attributed to a mixed protolith comprised of clay and ferro-manganese oxides (mainly amorphous goethite with lesser todorockite-birnessite). Manganiferous pyroxenoid rocks are probably derived from alumina-poor ferromanganese cherts,similar to Japanese tetsusekiei.Rare earth element compositions ofBroken Hill garnetites are very similar to those of recent ferromanganese seafloor accumulations, suggestive of some genetic link.

Jan 1, 1990

By R C. Owen, M A. Ward

The paper describes the application of New Zealand's environmental impact assessment procedures to a proposed gold and silver mine in the North Island of New Zealand. The project is described and a summary is provided of the statutory permits or consents that are required prior to operation of the project. Emphasis is given to the requirement for environmental impact assessment and the preparation of a formal environmental impact report. The company's approach to impact assessment is described, with examples of how this assessment and the identification of management alternatives influenced the engineering design of the project. This paper was prepared as a contribution to a working session of the International Association of Impact Assessment VII Annual Conference, July 1988.

Jan 1, 1988

Difficult ground conditions in the area planned for placement of vent rises to the surface at the Porgera Goldmine led engineers directing the project to chose blind shaft boring methods of shaft construction from the available alternatives. Zeni Drilling Pty Ltd was first contracted in 1988 to install a group of three closely-spaced, steel lined shafts. The success of these led to an order for a fourth hole in the same group followed by two more, less than a kilometre. away, under a separate contract in 1992. All of the shafts were completed on.schedule to within one day. The only significant difficulty arose during commencement of the last shaft when the strata collapsed trapping the drilling tools and jeopardising the stability of the surface collar pad. The situation was corrected by innovative lining techniques and the project went on to finish on schedule. This paper discusses the application of various technologies associated with the project including aspects of geotechnical input, drilling fluid chemistry, mining engineering and logistics.

Jan 1, 1993

By Roberts T. J, Thomson I. A

Mill scale, which contains a high proportion of magnetite and wustite, was added to the feed to the Whyalla grate kiln pellet plant during the production of acid pellets for domestic consumption. Its addition resulted in increased production -rates together with reduced consumptions of bentonite, fireclay and fuel. Mill scale was particularly beneficial when treating feed containing difficult to process, earthy, high ignition loss iron ores. Test work in the laboratory and subsequent plant experience showed that the magnetite and wustite oxidised in the drying and preheat sections of the travelling grate. The additional heat reduced gas flows through the grate kiln system, aided the drying of green balls containing earthy ores and increased the preheat strength of the balls. These advantages were offset to some extent by higher power consumptions to grind the harder mill scale and process difficulties caused by the contamination of mill scale with oil and coke.

Jan 1, 1974

By Basillo CI

The adsorption mechanisms of various thiol collectors can be subdivided into four classes: chemisorption, EC-mechanism, catalytic oxidation and metathetical substitution. The chemisorption mechanism occurs at potentials below the thermodynamic potentials for the metal-thiol compound formation and is reversible. The EC-mechanism occurs when the mineral is sufficiently oxidised to liberate metal ions to form metal-xanthates; therefore, it is observed with more easily oxidisable minerals and/or with collectors having large pK values. Thionocarbamates adsorb on sulphide minerals via the EC-mechanism due to their large pK values. Although the adsorption occurs at very low potentials as compared to xanthates, it is irreversible with large overpotentials. On the other hand, the adsorption of modified thiophosphates and thiophosphinates occurs near the thermodynamic potentials because of the low pK values. The metathetical substitution is believed to occur only when a mineral is highly oxidised. These classifications are useful for studying the effects of electrochemical potentials and the molecular structure on the collector adsorption Mechanisms.

Jan 1, 1993

By Davey FJ

The Hikurangi Margin of eastern North Island New Zealand represents the feather edge of the over-riding Indo-Australian Plate at its convergent boundary with the subducting Pacific Plate. Towards the south, convergence becomes slower and increasingly oblique, and sediment supply from the Southern Alps becomes increasingly rapid. In this environment a 150 km wide, imbricate thrust, accretionary prism has grown since the Miocene, uplifting slope ridges and basins and a range of coastal hills. Offscraping of thick, axially transported, trench-fill turbidites begins in a zone of proto- thrusts, which extends up to 25 km beyond the principle, slope-toe, deformation front. On the slope, landward tilted, trench-slope basins are separated by ridges. The ridges ride up on thrusts that sole out at a major decollement. The decollement dips landwards at 3 degrees to a depth of 14 km at the coast, where it coincides with an onshore zone of high seismicity. Beneath the decollement, about 1 km of consolidated, oceanic sediment is going under the margin with the underlying oceanic basement. Some of these sediments may underplate the frontal ranges to the west and geochemical evidence of subducted sediment is found in the volcanic zone beyond. A rapid decrease in the width of the accretionary prism to the north is associated with a decrease in sediment supply and perhaps with a dislocation in the downgoing plate. To the south, the accretionary prism narrows, swings westward, and merges into the zone of very oblique collision that marks the transform between mirror image subduction to north and south of New Zealand.

Jan 1, 1987

By Anderson RJ

Tower Mills are used at Aberfoyle's newly commissioned Hellyer base metal sulphide concentrator. Hellyer ore is particularly fine grained. To achieve adequate liberation fine grinding is necessary. Three Tower Mills are used on regrind duties, grinding to less than 20 microns. The physical arrangement, material flows and grinding characteristics for the Hellyer Tower Mills are described. The mills have performed satisfactorily, both in size reduction and power efficiency. Wear parts must be inspected and changed more often than with ball Mills. To date, 92 per cent availability has been achieved. As parts and maintenance routines are rationalised, this is expected to improve to 96 per cent. Modifications to wear parts for the Hellyer Tower Mills are discussed.lhc Tower Mill grinding environment is highly reducing. The impact of Tower Mill regrind on downstream flotation is discussed.

Jan 1, 1991

By V Lickfold, A J. Crawford, A J. Wilson

A total of 12 alkalic porphyry centres of Late Ordovician age have been discovered in two mineral districts within NSW. The alkalic porphyry deposits are hosted within shoshonitic volcanic centres that formed where a major cross-arc basement structure (the Lachlan Transverse Zone) cut the Ordovician Macquarie Arc. The Macquarie Arc was amalgamated with the back-arc basin sediments of the Wagga Marginal Basin and with the proto-Pacific margin of Gondwanaland to form the Lachlan Fold Belt after the cessation of arc magmatism in the Late Ordovician. Within the Ordovician volcanic belts of NSW, the alkalic porphyries are the most significant mineral deposits economically. The combined resource of the Cadia district porphyries (729 Mt @ 0.79 g/t Au and 0.30 per cent Cu) makes Cadia the worldÆs seventh largest known porphyry gold system and the largest known gold resource in an alkalic porphyry system (574 t Au). Hydrothermal alteration in the alkalic porphyries comprises a complex sequence of potassic, calc-potassic, sodic, calc-sodic, propylitic and late-stage, typically fault-controlled phyllic assemblages. Hematite dusting is common in many of these alteration assemblages, giving the intrusions and the altered volcano-sedimentary host sequences a distinctive pink-orange colouration. Intensely developed hydrothermal alteration assemblages are localised to within a few hundred metres of the composite intrusions that sourced the mineralising fluids, making these deposits difficult exploration targets. Sulfides are typically zoned, with several of the deposits having bornite-rich cores, chalcopyrite-dominant annuluses and pyritic outer haloes. Gold is well correlated with bornite in most of the deposits, and with chalcopyrite at Cadia Hill.

Jan 1, 2002

The correct design and effective operating strategies of metallurgical plants require a constant analysis of data gathered for process control, or for due accountability. Conventional, oldfashion statistical tools often fall short of helping management, either because they are too complicated and ambiguous, or because they fail to address structural problems leading to causes of setbacks. This paper focuses on three statistical tools known for their practicality and the in-depth perspective they offer in attempts to retrieve important information from existing data. These tools also provide a better appreciation of the importance of carefully selected data quality objectives. Chronological data are meticulously gathered and stored at considerable expense: They have value, and it is the duty of management to take full advantage of them. These three selected tools are the variogram and its auxiliary functions, the moving average and its auxiliary functions, and the relative difference plot. This paper offers solutions, and a reference for managers to optimise metallurgical plants.

Jan 1, 2002