Search Documents

By G Showers, R Triglavcanin

The complexity of understanding the whole thickening process to achieve real performance improvements cannot be underestimated. The last significant change in feedwell design was more than 15 years ago with the introduction of self-dilution systems û firstly with OutotecÆs Autodil, followed by FLSmidthÆs E-Duc. Now, following many years of extensive in-house research, including close collaboration with AMIRA and the CSIRO, Outotec has launched the next generation Vane Feedwell. The Vane Feedwell has been globally patented and installed at various sites. This paper briefly outlines the feedwellÆs development using CFD modelling and its subsequent performance in a æreal lifeÆ site installation. Plant results of the first commercial Vane Feedwell, in a mineral sands application, are discussed. The Vane Feedwell was retrofitted so comparative data of pre- and post-installation is shown.

Jan 1, 2009

By Li YQ, Yoon RH

The photoresponse of natural mineral pyrite and galena electrodes has been studied in aqueous solutions on freshly fractured surfaces (some fractured in situ) using moderate overvoltages. When fractured in situ, the electrode potential of both minerals instantly drops several tenths of a volt. Pyrite exhibits a spontaneous anodic photocurrent at fracture, which indicates upward band bending (depletion layer) on the n-type electrodes. The negative surface charge responsible for the depletion layer is believed to arise from a surface state that is intrinsic to pyrite surfaces, possibly modified by hydroxide ion adsorption. The flat band potential, Vty, of pyrite is at approximately -1.0 V (SCE) at pH 9.2 but to reach V(b, pyrite has to be cathodically decomposed. In contrast, galena assumes the flat band potential at fracture. Subsequent polarisation of galena at potentials positive of Vth produces an anodic photocurrent (upward band bending) and polarisation negative of Vro a cathodic photocurrent. Most of the galena electrodes studied were degenerate n-type and at potentials negative of Vtb, no cathodic photocurrents are observed, indicating the bands cannot be bent downward, consistent with the Fermi level at the surface merging with the conduction band edge near Vn,. Several were close to intrinsic, with the photocurrent changing sign near Vn,.

Jan 1, 1993

By Ghiani M, Currelli L, Fuganti A

the results of an experimental study aimed at beneficiating a complex ore containing bastnaesite and other rare-earth minerals, with associated barite and fluospar are illustrated. Owing to its minero-petrographic, physico-mechanical and structural characteristics, the crude ore is not amenable to classic concentration methods, such as flotation, magnetic and gravity separation. Therefore the technical feasibility of selective disintegration followed by size classification has been studied, whereby bastnaesite and the other rare-earth minerals can be concentrated into the finest size fractions. Leaching and subsequent extraction of rare-earth metals by liquid-liquid separation represents the final stage of beneficiation.

Jan 1, 1993

By G J. Corbett

Magmatic-related low sulfidation hydrothermal ore systems at plate margins exhibit distinct spatial and temporal zonations which can be used to aid mineral exploration and development. Low sulphidation systems at all crustal levels exhibit the same paragenetic sequence of events: early breccia formation, followed by quartz - secondary feldspar sericite/illite veining, then mineralisation, and final argillic overprint. This sequence of events is interpreted to reflect the initial emplacement of melts at high crustal levels, and the progressive cooling of that melt and release of magmatic constituents into a circulating hydrothermal system.   Low sulphidation systems in the south-west Pacific region exhibit a vertical zonation in deposit types: from porphyry copper-gold at deep levels, quartz-sulfide-gold at mesothermal to deep epithermal levels, carbonate-base metal gold at mainly epithermal levels, and epithermal quartz silver-gold at shallow levels. It is interpreted that the characteristics of each of these styles of deposits is produced by mixing with circulating waters of different physio-chemical compositions.

Jan 1, 1995

The original leases making up today's North Kalgurli Mines were developed by independent companies on an ad hoc basis. The major disadvantage which now arises is the varying levels of mining horizons. From Kalgurli Shaft in the south, through main Shaft and to Croesus Shaft in the north, there are three separate sets of levels. work has commenced to link the three areas with either common levels or new development which will facilitate common access and haulage via Main Shaft.Generally, the workings at North Kalgurli were established at the turn of the century. The introduction of techniques and equipment to bring the mine into the 20th Century has been difficult and slow. The general size of openings, a widespread workforce and complex ore distribution often make innovation and change more than a challenge.

Jan 1, 1985

The Jundee gold mining operation is located in the Western Australian Yandal Greenstone belt. Jundee is a mature operation encompassing multiple and complex underground ore resources, dwindling open pit reserves, large surface stockpiles, small satellite resources and two near-mine but stand alone process plants. The imminent completion of continuous open pit mining and the associated drop-off in total mill feed precipitated a review of the strategic mine plan and development of options that would optimise the exploitation of the remaining mineral resources and the utilisation of the existing plant and infrastructure.An initial review of the strategic decisions to be made, available options as well as the quantity, complexity and co-dependency of the strategic variables quickly led to the conclusion that an Operations Research style modelling approach would be appropriate. An 'off-the-shelf' program engine by the name of WHATSBEST! (LINDO Systems Inc.) was chosen on the basis of price, reputation and ease of use. The model was formulated with the unknown variables (being the ore mining rates) expressed as a proportion of the maximum achievable ore mining rate from each source. Costs were defined as variable or fixed, with this definition being a key aspect of the modelling process. The critical application of the model was in determining the optimal extraction rate of ore, the destination (ie Jundee or Nimary mill) and the sequence of extraction of each ore source that maximized the cash flow of the operation. The program was designed to be able to quickly derive an optimal result from the many variables, replacing the previous laborious iterative process of arriving at an acceptable answer by means of several large and static spreadsheet models. This paper presents the process of selection, formulation, application and scope of operation of the turn-key linear and non-linear program strategic model now used as part of the Jundee Operation strategic decision making process.

Jan 1, 2002

By Woodcock J. T, Rummel P. H, Sparrow G. J, MacRae C. M

An automated method, which is believed to be the fastest in the world and which can be used by mineralogically-untrained technical assistants, has been developed for the rapid location of native gold particles and other gold minerals down to 1 pm in size in ores, concentrates, and tailings using a scanning electron microscope. Searching of a 25 mm diameter polished block in 1 pm steps usually requires 3-4 h. Examples of the location of native gold and gold tellurides in drill core sections, in crushed ore samples and gravity and flotation concentrates, and in various metallurgical test products are given. The results have application in ore exploration, in guiding metallurgical test programmes, and in assessing metallurgical per- formance in testwork and in operating plants.

Jan 1, 1991

By S Miller, A Neale

As part of a long-term acid rock drainage (ARD) mitigation study, PT Freeport Indonesia has completed the construction of a highly instrumented, full-scale, experimental, overburden stockpile to further evaluate the behaviour of the waste rock system at Grasberg mine. A total of 24 lysimeters, 30 sets of thermistor strings and 48 oxygen-sampling ports were installed at select locations during stockpile construction. ARD flow rates and chemistry have been recorded since the start of overburden rock placement in April 2000. Measurements of in situ temperatures and oxygen concentrations quantify reaction rates and the oxygen pathways that control oxidation kinetics deep within the waste rock profile. Direct field observations show the significance of advective oxygen flow with respect to the onset of oxidation kinetics. Oxygen measurements show that the rubble zone that forms at the base of a waste rock bench provides a critical pathway for oxygen entry to the waste rock profile. Furthermore, rapid oxidation as evidenced by measured temperature increases deep within the panels of waste rock is observed to occur. The observations presented in this paper provide critical insight for understanding the mechanisms and behaviour of full-scale waste rock stockpiles with respect to ARD generation. The results of this program will assist in the future selection, testing and evaluation of appropriate mitigation measures with respect to surface and face treatments to reduce long-term ARD generation. This project is a work in progress, and at least another two-years will be required to fully understand site-specific ARD generation and ARD mitigation mechanisms. This paper will discuss various design and construction considerations, provide an overview of results achieved to date, and some preliminary interpretation of what is happening within the overburden stockpiles.

Jan 1, 2003

Close spatial relationships between the deposits of the Etheridge Goldfield (23,000 kg of bullion) and various regional geological and geophysical features suggest that genesis of the ore deposits was a multi-stage process that started with magmatic and metamorphic stages in the mid-Proterozoic, climaxed with structural and hydrothermal stages in the late Palaeozoic and terminated with an oxidation enrichment stage in the Cainozoic. Acceptance of this hypothesis permits classification of the Georgetown region into areas likely to contain deposits of the Etheridge type and those unlikely to do so. Consequently there is little scop- for the discovery of extensions of this field. However, the stratigraphic interval between the source rocks of the Etheridge field and stratigraphically higher host rocks of the Croydon field may contain disseminated replacement gold deposits of the Carlin type. The potential host (pyritic carbonaceous, and locally dolomitic siltstone of the Candlow Formation) is locally faulted and cut by granitoids and the extension of a mineralised, long-standing zone of structural weakness.

Jan 1, 1980

Hard rock TBMs are very often open machine layouts, with just a part roof shield over the front of the machine. The whole system is designed for fast face advance and the economy of the project often depends entirely on the rate of advance. Typically, hard rock conditions will demonstrate stable and good ground for a major part of the tunnel. However, short sections of crushed shear zones with clay and gouge material may cause serious time delays. Spiling rock bolting has been proven to be very efficient under such circumstances, provided the fully grouted rebar bolts can be placed in a controlled and practical manner.Environmental restrictions are becoming more and more a part of tunnel excavation projects. Even hard rock TBM tunnelling may require a strict ground water control, because of consequences on the ground surface from lowering the ground water level. Such consequences may be surface settlement, negative influence on ground water resources or damage to vegetation.Pressure injection ahead of the advancing tunnel face (in this paper named pre-injection), using microfine cement and chemical grouts, is today a proven technology. As examples can be mentioned (Garshol, 1997) about 100 km of pre-injected tunnels below Oslo City and about the same length of subsea tunnelling elsewhere in Norway. Examples from other parts of the world are also available, like below Stockholm, Sweden, the Inland Feeder project and Hollywood Metro both in Southern California.To take advantage of spiling rockbolts and pre-injection, it is an obvious prerequisite to be able to drill the necessary boreholes in the right positions and at the correct angle. In drill and blast excavation this is simple, but in TBM projects it has repeatedly turned out to be difficult. More than once owners have accepted bids containing reassurance from the contractor that the drilling method will be sorted out later. Experience shows that if ælaterÆ means after start of the TBM operation, it is often too late.

Jan 1, 1999

The implementation, during recent years, of the concept of distributing chilled water to improve cooling at the working faces represents a very important innovation for the mining world. In a logical extension to that concept it has been recognized that distribution of the cooling water at high pressure would provide a potential source of energy for driving water powered hydraulic machinery such as rockdrills, water jets for moving rock, and support props, in the workings. With this in mind, the Research Organization of the Chamber of Mines of South Africa is pursuing the development of such a dual system that will provide cooling in a deep mine and, at the same time, drive hydraulic machinery. A comprehensive design of such a system has been completed and has shown the concept to be entirely feasible technically using technologies currently available. A pilot system is working in a mine shaft 2000 m deep giving a pressure of 20 MPa at the bottom of the shaft and distributing the cold water into the workings at a pressure of 17 MPa. The system shows considerable potential for improving existing mining methods and will open the way for the development of new mining methods for deep mining operations.

Jan 1, 1986

By J E. Everett

A block model of the orebody is used to plan a mine. The first requirement is to identify ore to be extracted, discarding waste, so as to meet target grade, generally in multiple analytes. Commonly, cut-off values are set for each analyte, so as to distinguish ore from waste. It will be shown that, if more than one analyte is important, this procedure is wasteful of ore and a composite cut-off function is preferable.A second requirement is to sequence the ore extraction so that the variability in ore grade is controlled: failure to do so will result either in low-quality ore being marketed, or excessive re-handling being required to blend the ore to reduce the grade variability.A third requirement is that the extraction sequence should be such as to control the amount of equipment movement required, enhancing the equipment productivity.The overall objective, to optimise the Net Present Value (NPV) of the mined ore, is simply stated but complex in realisation, since so many factors, such as target grade, grade variability, equipment choice, equipment movement, and downstream blending all have alternatives which can be traded off against each other, and all of which contribute to the costs and benefits making up the total NPV.There exist commercial packages for ore selection and mine planning. However, they are often of a ‘black box’ nature, and users are sometimes not fully aware of the criteria being applied. In particular, the treatment of quality as a multidimensional vector may be problematic. The purpose of this paper is to discuss some of the issues involved and to suggest an alternative set of approaches, which should complement existing commercial treatments.The discussion will be illustrated specifically by reference to the mining of iron ore, but the issues are relevant to a wide variety of mining situations

Sep 5, 2011

By E Y. Baafi

Artisanal and small-scale gold mining (ASSM) offers lucrative employment opportunities to the locals of most developing countries. The major drawback of ASSM is its adverse impacts on the environment resulting from improper mining and processing techniques. Papua New Guinea (PNG) has very active ASSM activities. The artisanal and small-scale gold mining in PNG provide employment at local and national levels and the sector is an important source for inflow of foreign exchange into rural communities. However, small-scale mining activities are associated with sensitive health and environmental issues. The process of recovering gold by retorting and heating the amalgam over an open fire is a dangerous health practice. This paper discusses artisanal and small-scale gold mining operations in PNG and their impacts on the local environment.

Jan 1, 2008

By N Meyer

This paper presents a research project referring to the stability of submerged walls of open pit mines and the actual state of development. Obviously the slope stability analysis is always a rather complex problem, because it is difficult to reduce the problem to a design scheme and to define the available in situ soil strength. Especially the design of submerged slopes represents a problem. The state-of-the-art slope stability analysis is based on a simplified modelling of slope failure and soil behaviour and with this predicted stable slope inclinations of sand slopes below water-table are less then half the angle of internal friction. Slope angles calculated like that canÆt satisfy the mining companies. One of the problems that have to be solved is the reliable determination of the long-term stability of non-cohesive, submerged slopes, which is not only dependant on geotechnical and hydrogeological parameters of the subsoil, but is also significantly influenced by how the slopes are made. The research project points at the relations between mining and geotechnical engineering with the main aim to find a more suitable stability analysis which takes both soil behaviour and mining influences into account.

Jan 1, 2003

There is a well-known saying, variously attributed to the great King Solomon and other sages of antiquity, to the effect that 'there is nothing new under the sun'. The inventive genius of man, as far as it is personified in the metallurgist, has often had the truth of this statement poignantly brought to mind when investigating the priority of ideas in its own particular branch of science. Not infrequently some operation, at first inilocently taken for a novel procedure, has later been found to have had an irrefutable precedent in the more or less remote past.When confronted by a question of this kind the metallurgist can generally much simplify his search if he at once turns his scrutinising gaze towards that ancient home of metallurgy, Germany. Vast departments of the smelting art have originated there, and even when Germany has not been in position to claim priority of invention, it has at least been characterised by a distinction equally as worthy - ie that of the faithful and authoritative exposition of the theoretical grounds on which the invention rests.In the present instance, in endeavouring to trace the history of pyritic smelting, the writer has naturally turned in the abovementioned direction, and not without some result, although the recorded data are, as might have been expected, meagre. A complete history of the art of beneflciating ores by means of fire, in all its many ramifications, still remains to be written. Possibly it may never be written, for the extent of the subject is tremendous. It is even practically impossible to clearly trace the development of one of its most modest sub-branches in satisfactory detail, or to present that branch without going to a considerable extent into related matters of a merely general character. For the purpose of dealing with the subject it will be convenient to divide it into two concurrent heads, and to distinguish, for historical reasons as well as for metallurgical ones, between that branch of the general method of matte smelting, which, until about 1891, has been called 'pyritic smelting', and the more recent offshoot of the latter, which, by distinction, may be called 'pyrite smelting'. The nature of pyritic smelting was clearly defmed by Dr John Percy in 1880, and his interpretation3 may be accepted as well known. To recall the characteristics of the method we may perhaps paraphrase Dr Percy's meaning by describing the process as a special method for the smelting of lean or dry silver or gold ores, which do not contain sufficient lead or copper for these metals to act conveniently as collectors of the precious metals. The operation is conducted in a blast furnace, with an amount of carbonaceous fuel sufficing to produce an exclusively reducing atmosphere, and with the addition of pyrites, in order to form a regulus in which the precious metals shall be concentrated, the pyrites themselves being either argentiferous, auriferous, or cupriferous, or any combination of these three, or wholly barren of metal values. In the common acceptation of the term, it is understood that the use of the reverberatory furnace is excluded.

Jan 1, 1994

By Carter LC

Following the perception by the Groote Eylandt Mining Company of a need to further beneficiate a fines product, and preliminary metallurgical testing to demonstrate the feasibility of such beneficiation, a comparison was made of the various configurations of cyclonic heavy medium separators available. This comparison consisted of (i) a pilot plant test in which a dynawhirlpool (DWP) and a pump fed cyclone were compared, and (ii) a survey of operating plants using the systems under consideration. Little metallurgical difference was found-between the different systems. The gravity fed cyclone configuration was finally chosen based on a particular need to minimise degradation of ore and on a desire, in so isolated a location, to use established and locally supported technology.

Jan 1, 1987

The products required by customers today have become far more complex and consequently more demanding to handle. And thereÆs the dilemma. Nowadays, people tend to stick to a trade for just a few years instead of for a lifetime, and this means that the customerÆs employees cannot be expected to get more than general knowledge of how to handle modern mining and construction equipment. To meet this challenge, major steps are being taken by suppliers to make their æmusclesÆ more user-friendly. Also the supplier is assuming a larger share of responsibility for the product including operators training, supply maintenance services and, in many cases, performance guarantees. In other words, the supplier is today supplying a function or an activity rather than just muscles. Some of the new generation drill rigs have been on the market for a few years and reliable experience has been collected and is addressed in this paper. Some of the information is well supported by figures while others are just statements from users of the rigs.

Jan 1, 2005

By U Briem, R Verreet

The level of wire rope technology used in mine hoisting applications has a significant effect on the overall efficiency of the hoisting system. This paper discusses the effect that a reduction in rope mass per unit length and an increase in rope breaking strength can have on rock skip capacity and hence mine shaft output. A 20 per cent reduction in rope mass per metre for a typical 48 mm hoisting rope, while maintaining the breaking strength, increases the skipÆs capacity by circa 30 per cent at a suspended rope length of 3000 m. Such gains in shaft output, without any significant changes to the shaft or winder design, can have major implications for the feasibility of future deep mine projects. The technical challenge for rope manufacturers is how to get rid of 20 to 30 per cent of the rope mass while keeping the breaking strength and modulus of elasticity of the whole rope constant. CASAR are currently developing steel wire rope constructions where the steel IWRC has been replaced with high strength, high modulus fibres such as Kevlar«, Spectra« and Dyneema«. One of the key aspects of such composite rope designs is to ensure equal load sharing between the different rope components, ie in proportion to their area. If there is a significant difference in modulus between the fibre core and the steel outer strands, the core may not carry its proper proportion of the load and the outer strands would be overloaded. Some technical aspects of the design of composite steel wire ropes are discussed. A design and operational issue that needs careful consideration is the safe non destructive testing (NDT) of composite ropes. Traditional magnetic NDT would only be capable of inspecting the steel wires. Techniques therefore need to be developed that would give operators a reliable indication of the condition of the load bearing fibre core. This paper also discusses possible solutions to this very important NDT question.

Jan 1, 2005

Milling operations at Misima Mine are discussed, with specific reference to the application of energy and cost saving concepts. Design stage innovations and post-commissioning developments are covered. General operational problems are described with specific reference to problems associated with operating in a remote location.

Jan 1, 1994

Mathematical modelling of continuous rotary vacuum filtration has been limited by the wide range of variables and the absence of connecting equations linking the variables. The filter type and size, mechanical design and predicted performance are generally determined by laboratory leaf tests on representative samples of slurry, or plant samples from an operating filter. A model has been developed which includes the major process variables such as slurry feed rate and concentration, cake thickness, wash water and air flow rates, to predict the filter production throughput, cake moisture and residual solubles. Where possible the model incorporates well established equations relating form filtration, washing and drying rates of the filter cake. Where an equation has not been formulated, standard curve fitting programs have been used to establish an algorithm. The theoretical equations and the derived algorithms are defined in the text. A major feature of the model is that operators, metallurgists, process, mechanical and instrumentation engineers become more aware of the interaction of process variables, the principles of the equipment design and its limitations when operating at peak performance. The model has specific application in the alumina industry where a high moisture content of the filter cake can increase chemical losses and energy costs, and in the coal industry where overseas companies are insisting on lower export coal moistures.

Jan 1, 1989