Search Documents

By L Smith, R Beckie

An intermediate scale (8 m + 8 m + 5 m high) constructed waste rock pile experiment was built upon a contiguous grid of 16 gravity drainage lysimeters to investigate the flow of water in unsaturated waste rock. Average net infiltration to the uncovered waste rock pile is 55 per cent of precipitation. Large rainfall events have net infiltration of 55 per cent to 85 per cent. Net infiltration estimates range from 23 to 120 per cent of precipitation between lysimeters. Small-scale lysimeters of less than 4 m2 area are shown to be poor predictors of net infiltration for uncovered waste rock. The appropriate size for lysimeters increases with increasing flow rate. The residence time distribution has an estimated median value of 3.0 to 3.9 years under average infiltration conditions. Water flows within the fine grained matrix, within larger pores (macropores), and in matrix free areas of the pile. In situ tracer concentrations vary between pore sizes, and between spatially distinct areas of the pile, indicating water geochemistry may also be variable. Water samples collected from in situ soil water samplers are dominated by the most mobile water fractions. In situ measurements of water content and matric suction are compared to the measured outflow. The data indicate the focusing of flow in spatially distinct areas can make in situ instrumentation a poor (non-conservative) predictor of volumetric water flow.

Jan 1, 2003

By Teague JWS, Jung RF, Kadletz O, Jones DR, Jones CJ

A study of the passive treatment system for Hilton minewater revealed that it consists of four main process steps. The water, which contains soluble and particulate iron and zinc and is supersaturated with CO , is pumped to the surface and then passes throuqh a degassinq unit into settling ponds where larger particles of iron hydroxide, containing some adsorbed zinc, can settle out. The still turbid supernatant is pumped to the top of a hill, from where it is allowed to trickle in a broad sheet, releasing CO , towards an earthen channel in the valley below. Consequently the pArises from around 6 to 7.5. This in turn promotes further decrease in the concentration of soluble zinc by increased adsorption of zinc on to iron hydroxide particles. The channel then transports the water to the third process in the system - a 53 ML pond acting primarily as a flocculation-sedimentation basin. The clarified water overflows into a second channel, downstream of the pond, which constitutes the fourth process in the system. Here, copious quantities of filamentous algae further reduce zinc concentrations to acceptable levels before the water is collected for recycle into mine operations. The work reported here represents a detailed study of this system and describes the optimisation of the operation of each of the individual steps involved.

Jan 1, 1988

By M Fuchs

Roadheaders were introduced to mining and tunnelling in the early-1960s. Since this period their main field of application has been for roadway drivages in coal mines and for mineral production, for instance in coal, rocksalt, potash and gypsum mines. Their main field of application in tunnelling is in softer and partly friable rock formations, a suitable area for non-blasting excavation. However, in longer tunnel sections excavators with high ripping forces have replaced roadheaders in many situations. The main arguments against roadheaders have been and still are:a sharp increase in excavation cost with increasing rock strength and increasing abrasivity; and greater risks in conditions which have not been, or could not be, investigated to a sufficient extent. These arguments have, to a great extent, restricted practical roadheader application in production mining and in a lot of æstandardÆ tunnel projects. To address these limitations, factors which could make roadheaders attractive for such conditions and could overcome existing technological difficulties have been investigated. Extension of the economic field of application in hard rock was found to be the most important and the most effective step forward.

Jan 1, 2002

By J Isles, S King, A Valenza, R Lawolo, J Evert

PT Nusa Halmahera Minerals (PT NHM) is an Indonesian joint venture company owned by a subsidiary of Newcrest Mining Limited (75 per cent) and PT Aneka Tambang (Persero) (25 per cent). PT NHM operates two underground gold mines, Kencana and Toguraci at the Gosowong mine site in North Halmahera District, North Maluku Province, Indonesia.The Toguraci underground mine development commenced in 2011 with ore production commencing in 2012. Water temperatures ranging from 50°C to 80°C were encountered in the Toguraci open pit associated with the structures containing the gold bearing veins and are believed to be fed from a relic volcanic system one to two kilometres below the mine. Underground development and production has continued to intersect these structures with the result that an integrated programme of geological, hydrogeological modelling and operational project work has been required to dewater the mine ahead of the descending stoping fronts.This paper will detail these programmes.CITATION:Lawolo, R, Isles, J, Evert, J, Valenza, A and King, S, 2017. Hot water management at PT Nusa Halmahera Minerals’ Toguraci Mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 191–198 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By M Zhu, G Tranell, J You, K Tang, X Ma

The thermal conductivity of slag is critical for the efficiency of high temperature metallurgical processes such as the smelting reduction of ferroalloys, the ladle refining and the continuous casting mold flux in steelmaking. Experimental determination of slag’s thermal conductivity is fraught with challenges, as seen in yielding data for the SiO2-Al2O3-CaO system that are often inconsistent and widely dispersed. In molten slags of this system, thermal transport occurs via phonons within the network structure. To quantitatively describe thermal conductivity based on the microstructure, hightemperature Raman spectroscopy was employed to measure the silicate tetrahedra Qi (i = 0, 1, 2, 3), with Q4 species inferred from mass balance. This study also integrated molecular dynamics simulations to provide a fundamental understanding of the microstructure units distributions. Machine learning algorithms, especially deep neural networks, were applied to establish the relationship between slag composition and the configuration of tetrahedra. The thermal conductivities were then connected with silicate tetrahedra Qi using an Arrhenius-type formalism. This study sets the stage for extending our findings to more complex, multicomponent slags, enhancing their practical application in industrial processes.

Aug 21, 2024

By Kane, M O&apos

The mineralised members of the Brockman Iron Formation mined at Mt Whaleback are overlain and underlain by shale horizons. To maximise resource recovery, waste movement within the life of mine plan will total approximately 3.3 billion tonnes. Approximately 15 per cent of waste materials contain zones with varying amounts of sulfides and carbon and are referred to as æreactive shaleÆ. Reactive shale has the potential to self-heat and can react with some explosives, resulting in spontaneous explosion. Sulfide rich zones also have the potential to generate acid rock drainage (ARD). Successful mining of reactive shale requires constant co-ordination between the geology, mine planning, mining and environment departments. Safe storage of reactive shale is the focus of ongoing research. Since the mid-1990s, a number of trials have been undertaken at Mt Whaleback in order to further the understanding of the physical and chemical properties of reactive shale. This paper summarises some of these trials, and discusses key learnings arising from interpretation of results. Ultimately, the learnings from this research will provide the guidelines for successful storage of reactive shale.

Jan 1, 2003

By N LaBranche

The resurgence of Silicosis and Coal Worker’s Pneumoconiosis (CWP) in coalmines has placed the spotlight back on the management of worker exposure to particulate matter across all mining sectors (Coal Workers Pneumoconiosis Select Committee, 2017). There already exists a substantial body of knowledge on particulate matter and its impacts upon human health (National Academies of Sciences, Engineering, and Medicine, 2018). The contribution of silica to respiratory disease is well known and there is a growing concern for exposure to diesel particulate matter. However, it is also clear that there are major gaps in our understanding. In part, those gaps relate to the contribution to adverse health effects of mineralogical constituents in the dust (LaBranche et al, 2021a). It is also becoming evident that the size and shape of the particulate matter can affect its potential impact on human health.The University of Queensland has developed a methodology for characterising respirable and inhalable dust samples using scanning electron microscopy. Multiple samples from numerous mining operations have already been analysed using the UQ methodology. The process has been successful in showing the variety of mineralogica lcomponents and particle size distributions presentin various areas of the mines.

Oct 12, 2022

By M Hino, D R. Swinbourne

The thermodynamic properties of arsenic in metal, speiss, matte, slag and gas phases are first summarised in this paper. Arsenic associates with sulphide minerals and generally has compounds of high volatility, but it has a weak affinity for sulphur and a strong affinity for metals, especially copper and iron. In the initial stage of the oxidation of sulphide concentrates arsenic is volatilised easily prior to the oxidation of FeS, although it tends to be fixed in the condensed phase as FeAsO4 if the concentrate is over-oxidised. Thermodynamic simulation of oxidative copper smelting reveals the distribution of arsenic between matte, slag and gas, and the possibility of condensation of arsenic from the resulting waste gas is discussed. In reductive smelting more arsenic remains in the metal or matte, and is sometimes concentrated as a separate speiss phase. The phase relations and thermodynamic properties of speiss are also summarised briefly. Arsenic refining from smelted copper metal is shown, from an examination of the basic principles of arsenic removal into slags, to be difficult. Owing to its weak affinity for lead however, arsenic refining from lead bullion is seen to be much easier.

Jan 1, 2000

A synthetic gold-silver telluride material (mainly sylvanite) has been prepared and its physical and chemical properties checked. Flotation tests using a Hallimond tube were conducted using commercial xanthate collectors. At collector concentrations of 10-3M with the addition of 5 × 10-4 M CUS04, no obvious differences in the mineral recoveries were seen irrespective of whether amyl, secbutyl, isobutyl or isopropyl xanthates were used. However, when the concentration of xanthate was reduced to 10-4 M or in the absence of the copper sulphate activator, the effectiveness of the collectors was in the order: amyl > secbutyl > isobutyl > isopropyl > ethyl. Changes in the slurry pH appeared to have little effect on the recovery of the telluride mineral.Leaching tests of the precious metal telluride showed that both gold and silver dissolve in alkaline oxygenated cyanide solutions but at a much lower dissolution rate than metallic gold or silver. Both leaching tests and electrochemical measurements indicate that the dissolution rate of gold-silver telluride is controlled by the pH and cyanide concentration of the leachant.Roasting the gold-silver telluride materials in air at temperatures between 550 and 750°C resulted in its decomposition into a metallic gold-silver alloy and tellurium dioxide.

Jan 1, 1994

In the time since the first trials in the mid-1980s, the Rare-Earth Magnetic Separators (REMS) are presently (year 2001) found in many heavy mineral sands plants around the world. Both the roll and the drum type are used from ilmenite concentration to cleaning high-purity zircon products. Chromium-bearing materials are removed from ilmenite more selectively than with electromagnetic separators. Greater flexibility and higher grades in ilmenite circuits are achieved. Cleaner rutile and zircon products, even with respect to levels of radioactive materials, are the result of superior magnetic force optimisation. Tailings from roaster plants can be reprocessed effectively, which is encouraging some operators to look at replacing old equipment in order to process roasted material plant feed or implement use of the new generation drum separators in new plants. Wet separation of ilmenite by using powerful wet REMS drum separators is now a possibility. This may be an alternative to at least a portion of the Wet High-Intensity Magnetic Separators (WHIMS) process for ilmenite preconcentration. A dry plant process flowsheet can often be modified by displacing a portion of high-tension separators with new high-temperature tolerant REMS.

Jan 1, 2001

By L Wsrell

During recent years the iron ore industry has experienced a continuous consolidation trend following increased merger and acquisition activities. Analysing and evaluating these mergers is important in order to establish potential effects. The purpose of this paper is to analyse the price effects caused by the merger between Rio Tinto and North Ltd in 2000. The merger was cleared by the European Commission, as well as the Australian Competition and Consumer Commission, shortly after its announcement. The analysis will be conducted using a simulation model based on a proportionality calibrated almost ideal demand system, which uses the premerger situation in order to estimate the post-merger outcome. The relevant market is defined using shipments data. This is followed by the simulation model applied to the defined relevant market. The results show that the concentration on the market, given by the HHI, increases approximately 15 per cent, and that the market share of the new companyÆs reaches almost 20 per cent. Compared to the CommissionÆs assessment the results indicate a more concentrated market and thus a higher concern for possible competitive effects. Furthermore, the results suggest that the predicted average market price increase from the merger is 1.6 per cent. However, the merged firm is able to increase their average price by 5.1 per cent.

Jan 1, 2005

THE following paper is a description of the plant and operations of the above company in their recovery and treatment of the quartz tailings deposited as final residues by the various mining companies. at Waihi, Karangahake, and Waitekauri into theOhinemuri River. During the past few years the silting of the Ohinemuri River has increased to such an extent as to cause considerable interest and discussion, and has lately been the subject of a most extensive inquiry by a Royal Commission, to consider the best means of dealing with what is generally spoken of as a public nuisance.Ever since the commencement of mining in this district, which was opened as a goldfield in 1875, the various mines operating have been discharging their tailings into this river, it having been proclaimed a sludge channel in 1895. Up to the year 1900 the quantity of quartz crushed was not large, probably not exceeding 500,000 tons; but since that date the annual tonnages discharged have increased enormously, and at the present time would total from 550,000 to 600,000 tons per year. Records show that up to the end of 1910 at least 5,000,000 tons have been crushed, for an actual yield of bullion considerably exceeding £10,000,000 in value, and all the valuable tailings from...

Jan 1, 1911

By Urabe T

In June 1989 a diving cruise of the French submersible Nautile has been carried out on the North Fiji basin spreading ridge. The objective of the cruise was the geological and geochemical study of the active spreading axis and associated hydrothermalism processes. This operation was the third cruise of the French-Japanese STARMER project following two cruises of the R/V Kaiyo in 1987 and 1988.INTRODUCTIONAfter the Seapso III cruise (Auzende et al., 1986, 1988a and b) of the R/V Jean Charcot in 1985, the objective of the Kaiyo 87 and 88 cruises was the complementary Seabeam mapping of the North Fiji Basin spreading axis between WS and 22'S and a systematic sampling (water and rocks) and deep towing (TV and photos) at about every ten milles along the axis.

Jan 1, 1990

The introduction of rubber tyred diesel equipment underground in the early 1960's and subsequent design improvements to diesel haulage systems over the past 2 decades has meant that diesel truck haulage has often been the first choice when selecting a haulage system for a new underground mine. Even today only 9% of all vehicles underground are electric powered.However, with the development of more efficient electric haulage systems, the suc-cessful installation of low cost shaft hoisting systems and improvements in conveyor design, alternative haulage systems are appearing as viable alternatives to diesel truck hauling. In particular, the aspects of ergonomic and environmental operating conditions, maintenance and operating costs as well as productivity rates are becoming more and more important in the selection of underground haulage systems. Future develop-ment of existing diesel haulage systems will require that diesel haulage units become more productive, have considerably reduced exhaust emissions compared to existing units and remain the cheapest haulage method for under-ground one way haul distances up to a distance of 3 kilometres. Development of electric truck and associated fuel cell haulage systems

Jan 1, 1985

By N LaBranche

The resurgence of Silicosis and Coal Worker’s Pneumoconiosis (CWP) in coalmines has placed the spotlight back on the management of worker exposure to particulate matter across all mining sectors (Coal Workers Pneumoconiosis Select Committee, 2017). There already exists a substantial body of knowledge on particulate matter and its impacts upon human health (National Academies of Sciences, Engineering and Medicine, 2018). The contribution of silica to respiratory disease is well known. However, it is also clear that there are major gaps in our understanding. In part, those gaps relate to the contribution to adverse health effects of mineralogical constituents in the dust (LaBranche et al, 2021a). It is also becoming evident that the size and shape of the particulate matter can affect its potential impact on human health. The University of Queensland has developed a methodology for characterising respirable and inhalable dust samples using scanning electron microscopy. Multiple samples from numerous mining operations have already been analysed using the UQ methodology. The process has been successful in showing the variety of mineralogical components and particle size distributions present in various areas of the mines.

May 5, 2022

With the advent of COAG reforms in the late 1990s requiring full commercial return from æpublic infrastructureÆ, and the tightening regulatory compliance for any project that involves the development or modification of any natural resource, it has become increasingly difficult for the private sector to contemplate development and/or ownership of new large-scale water supply infrastructure. The hurdles that must be overcome often seem insurmountable even before a detailed understanding of the project challenges can be developed. Australia has prospered over the last 50 years in an environment where regional development, including mining, has been encouraged by high commodity prices, a well-trained and available labour force and abundant spare capacity in the necessary infrastructure, in particular rail, power and water. Unless future infrastructure is created in advance of, or closely following, demand, this prosperity may be in jeopardy. This paper presents a snapshot of todayÆs project development challenges, and with reference to some recent case histories, argues that owing to their unique background, culture and status, water utility government owned corporations (GOCs) are well-suited to fulfilling the demand for new water infrastructure.

Jan 1, 2006

By P Fines, D J. Williams, G W, S Miller

This paper presents the results and findings of geochemical and mineralogical testwork conducted on samples collected from waste rock dumps at two mine sites, located in South Carolina, USA (Site 1) and Sudbury Ontario, Canada (Site 2). Important aspects of the relationship between the physical and geochemical aspects of the dumps are also presented. The overall aims of the project were to 1. determine if the physical and hydrological nature of the waste-rock dumps had any impact on the geochemical and mineralogical characteristics of the dump materials; and 2. to identify key implications for dump construction for ARD control. The results of geochemical and mineralogical tests indicate that the waste rock at Site 1 had undergone significant in-dump weathering and was relatively advanced with respect to ARD evolution. In contrast, the waste rock at Site 2 had undergone some weathering, however still contained a considerable amount of sulfide minerals. Testing also suggested that flushing of oxidation products at Site 2 had been limited, which therefore promoted the storage of oxidation products at the site. In addition, materials that had a D50 particle size in the range of 5 mm to 30 mm appeared to be more readily flushed than samples that had a D50 particle size of 30 mm. This suggested that preferential water pathways may have developed within the dumps at both sites.

Jan 1, 2003

By W A. van der Westhuizen, Beukes G. J, Vermaak J. J

Large parts of the arid northern Cape Province South Africa are blanketed by Quaternary cal- crete under which potential base-metal ore- deposits may occur. In an attempt to examine the nature of the distribution of such ore-re- lated elements in a calcrete environment, calcrete and soil samples from the copper-nic- kel prospect at Jacomynspan and the copper- zinc deposit at Copperton were examined. Both deposits form part of the Namaqua mobile belt. CALCRETE GENESIS In Southern Africa calcrete is restricted mainly to the western two-thirds of the sub-continent, south of the latitude 17¦ S. Various models have been put forward to explain calcrete genesis and Goudie (1973) and Netterberg (1969a) give detailed discussions on this topic. The most popular model for calcrete genesis is one of pedogenic origin. McPherson (1979), Watts (1980), Wright (1982), Arakel (1982), Netterberg (1969a), Goudie (1973) and Multer and Hoffmeister (1968), amongst others, support the hypothesis of calcrete formation by carbonate precipitation from downward percolating calcium carbonate rich soil waters. Calcium carbonate is usually initially precipitated as nodules or grains which can develop to form more compact layers.

Jan 1, 1988

By G Huggins

Excavation in underground jointed rock masses creates cavities into which the surrounding rock mass deforms. Deformations, besides intact rock deformation, include mechanistic deformations such as slip and rotation. In this paper deformational moduli were measured for prototype and blocky (jointed) models using elastic analogue methods for stopes from MIM LimitedÆs Lead Mine. The blocks for the models were defined in terms of the prototypeÆs joint sets, their spatial separations, orientations and average friction characteristics. From dimensional analyses, a relationship between prototype and model deformations was used to predict stope mid-span deformations. The results of this physical modelling work, conducted in the 1970s, motivated an investigation into the electro-treatment of tailings backfill to achieve improved strength and stiffness characteristics. Tailings backfill containing fines and having a high clay content can be electrically dewatered, and at times grouted, cemented, ion exchanged or agglutinated, to achieve relatively high magnitudes of strength and stiffness. These treated tailings stiffnesses can reduce the deformation magnitudes within a rock mass and, in doing so, reduce problems encountered in mine pillar extraction. The application of these tailings modification techniques is examined in relation to the elastic analogue methods.

Jan 1, 1998

By K Kuganathan, Y Potvin

Enterprise Mine at Mount Isa is to expand ore production from the current 1.4 to 3.5 mtpa by mining the 3500 Orebody, from which production is scheduled to start in February 1998 making this the deepest underground mine in Australia with its lowest mining horizon at nearly 1.6 km below surface. The following fill requirements were defined for the 3500 Orebody during the feasibility study: a minimum filling rate of 250 m3/h, a curing time of 28 days, and minimum free fill water. This paper mainly describes the investigation of high density and paste fills for the 3500 Orebody. The investigation covered all the key issues relating to fill option selection, including design criteria, material supply and demand assessment, drainage modelling, tailing dewatering method, mix design and a pump loop test. Results of the investigation indicate that both high density fill and paste fill are technically feasible. The investigation has led to the selection of a blended tailing paste for the 3500 Orebody as the paste option has significant advantages over high density fill in stope filling rates and fill reticulation. The blended tailing for paste fill is finer than Isa deslimed tailing but coarser than full plant tailing. The paste fill selected has minimum binder and tailing dewatering requirements while a relatively high filling rate is achieved.

Jan 1, 1998