Search Documents

By Adshead ND, Blake KL, Rotherham JF, Rotherham M, De Jong G

Magnetite deposits with distinctive ¦ actinolite ¦ apatite -bearing gangue and spatially-extensive sodic-calcic wall rock alteration occur in both Proterozoic metamorphic terrains and Mesozoic-Tertiary magmatic arcs. Examples from both settings constitute significant sources of iron ore (e.g. Kiruna, Sweden; El Romeral, Chile) and some host major Cu-Au deposits that have a local association with K-silicate alteration (e.g. Cloncurry district, NW Queensland; Copiapo district, Chile). A growing body of evidence points to a hydrothermal origin for these systems involving high temperature, low S oxidized fluids. The Cloncurry magnetite-Cu-Au deposits are products of the local structurally channelized influx of a specialized high salinity ore fluid into larger-scale alteration systems developed during pluton emplacement at greater depths than those associated with subvolcanic (porphyry) Cu-Au deposits. The geological characteristics of deposits in magmatic arcs are consistent with a similar mode of origin albeit in rather different tectonic settings.

Jan 1, 1995

By Dawson RD

For the past 45 years, the casting of refined lead ingots by The Broken Hill Asso- ciated Smelters Pty. Ltd. (B.H.A,S,) at Port Pirie has been mainly by use of manually operated rotary casting wheels of Newnam design. This style of operation was quite satisfactory as far as standard of product was concerned, but was manually intensive and a relatively high cost operation. With most other large scale lead producers already using automated-casting equipment, an investigation which commenced in 1966, progressed through stages of enquiry, design and development until the present plant commenced trial operations in late 1973, and fully operative in late 1974. While certain features of the plant are sed on overseas practices the plant was signed and built within Australia to BRAS ecifications. As constructed it consists two almost identical casting lines each pable of producing 25 kg ingots at 25 tonnes r hour using straight line casting machines d automated stacking weighing and strapping

Jan 1, 1975

Commencing early in 1975, Saraji Mine in Central Queensland will product 3.56 million tonnes in the first year and then 4.57 million tonnes annually for the Japanese and European markets. The coal will be mined from a series of pits separated by corridors which will be mined at a later date. Through the corridors flow regional drainage structures and power lines. Relatively easy areas will be mined initially to assist the cash flow and to minimise start-up difficulties. For ease of scheduling it is desirable that pit lengths exceed 3 000m but this will not always be possible. Ramps were designed using 1 200m spacing and 5 per cent gradient as optimum but modified to suit specific conditions. One ramp will be in the end of each pit nearest the ROM hopper and stripping will commence from this end. The advantages so gained are shorter haul distances, immediate access to the coal after stripping and simplification of the excavation of the first ramp. Haul road location was defined by the minimum present value of construction plus operating costs. Road design utilised airfield construction charts because wheel loads were outside the range of available road design manuals. Low load resistance characteristics of

Jan 1, 1974

By Moorrees C

Carbonic acid leaching of crude iron-containing magnesia derived from Savage River magnesite yields a magnesium bicarbonate leachate with a substantial soluble iron concentration. The iron concentration depends upon the leaching conditions (particularly time, temperature and pulp density) but is generally in the range 0.005-0.5 g/litre. If this soluble iron is not removed prior to the precipitation of the magnesium as a hydrated carbonate, then this product will be contaminated by the iron, and will not yield a final product (high-purity magnesia) that meets specifications.The soluble iron content of the magnesium bicarbonate leachate can be reduced to an acceptable level by addition of solid aluminium sulphate either during carbonic acid, leaching of the crude calcine or to the clarified leachate. Chemical analysis and X-ray diffraction revealed that the iron is precipitated as an iron-containing hydrotalcite-type compound, [Mg6(Al,Fe)2(OH)16]CO3.4H2O. The actual composition of the precipitate depends on the amount of aluminium sulphate added and the precipitation technique used. Because precipitation of iron in this manner also results in reduced magnesium recovery from the leachates, It WIll be necessary to develop methods for recovering the magnesium component of the precipitates.

Jan 1, 1984

By Tapponnier P

In North Vietnam, large ductile shear zones are observed along the Red river fault and the Dienbien fault. Left-lateral sense of the Red river shear zone is related to the direction of shortening E-W. NE dipping foliation planes is subvertical. Stretching lineation is subhorizontal ( 25¦). Left-lateral slip observed in the Oligocene Yansun granites demonstrates the major tectonic phase in Neogene, The stress field established from microfaults observed in triassic limestones, Oligocene granites and Neogene Conglomerates. Measurements of striations on fault mirors are used for calculating the stress tensor and for separating tectonic phases. Two tectonic phases in tertiary are separated : first tectonic phase related to the compressive direction E-W corresponds to the major tectonic phase represented by NW left-lateral shear zone. Second phase having the compressive direction N-S associated with the right-lateral movement of the Red-river fault zone opening of the Eastern sea and the Red-river and the Red-river delta is associated with the left-lateral movement along the Red-river.

Jan 1, 1990

By El-Ansary M

Estimation of in-situ resources and recoverable ore reserves for the Boddington Gold Mine feasibility study was done by applying an essentially "classical" ore reserve method. This relied completely on customized graphics-based computer software requiring close co-operation and interaction between geologists and mining engineers. All geological and mining outlines were interpreted and digitized manually. Classification of selectively mineable reserves into ore, marginal and waste categories was done using a method involving convolution, devised by Dr S Carras of the Systems Research Institute of Australia, and Mr R Hooper of Kinhill Stearns. The estimation process was complicated by the frequently conflicting requirements of the various joint venture partners. The resulting ore reserve figures therefore satisfied only the most general expectations of each partner.

Jan 1, 1987

As the gold price, and consequently ore reserves, improved in the late 1970's, a programme of upgrading the gold recovery circuit at the Phoenix treatment plant at Central Norseman was initiated. The introduction of oxidised ore with a high clay content from the North Royal open cut caused a reduction in thickening and filtering capacities, which in turn restricted plant throughput and increased gold losses in the residue solutions. Test work into alternative washing facilities showed that the installation of a five stage counter current decantation system would restore throughput and reduce soluble gold losses. Installation of the system achieved the objectives of increased plant tonnage, increased proportions of the high grade oxidised ore in the mill feed and decreased gold losses in the residue waters.

Jan 1, 1978

HISTORY Up until the late 1880's the mining industry acquired a considerable proportion of its capital needs from domestic sources. Exchanges were established wherever major new fields were opened and Ballarat, Bendigo, Charters Towers, Coolgardie, Kalgoorlie and Silverton all boasted active trading in mining shares. For much of the first half of this century there was only modest developments in the mining industry and its capital require- ments were correspondingly lower. RECENT EXPERIENCE The new mines of the sixties were, in many cases, characterised by their remote situation and their output of bulk commodities such as iron ore., coal and bauxite. Infra- structure costs were particularly high and the level of capital expenditure was of previously unheard of proportions.

Jan 1, 1975

Despite extensive oil exploration in"Western Australia over the past 12 years no commercial oil fields have yet been found. A total ' of 66 test wells have been drilled throughout the State but only Rough Range No.s.. 1 and 1A have produced oil in significant quantities. Active oil exploration is now in progress in the" Canning, Carnarvon, Perth, Bonaparte Gulf and Officer Basins. Test wells have been drilled' in ,all of these except the Officer Basin, where the subsurface stratigraphy is still unknown. Large .areas of the other four have hot yet been drilled. It, is- probable that. commercial oil deposits will eventually be found' in these basins as they contain thick marine sequences, and have structures 'suitable for.,the. entrapment of oil. .

Jan 1, 1964

By S Williams, N McBride

The aim of these analyses was to utilise the latest available production information for the Wandoo operation to determine the optimal blasting parameters, costing information and predicted results (fragmentation, muckpile shape and vibration). Much of the data used as input was made available from the information gathered during the excavation of the test pits during 1995. As with any æplanning stageÆ analyses, many assumptions were required to fill gaps in the available data. The calibration of computer blasting models was conducted using data from the last of the test pit blasts (this blast was carried out in material that closely resembled rock expected to constitute the bulk of the base case design pit). This calibration was refined using observation and experience based judgements to extend the accuracy of the predictions as far as possible. All the simulations were performed assuming that the blastholes will be wet (as instructed by BGM). This has consequently determined that the appropriate explosive for the simulations and the actual blasting will be a pumped emulsion/ANFO blend. The following blast design parameters were derived by determining a likely range of powder factor (from other similar scale gold mines) with a median value of 0.62 kg/m 3 being the powder factor arrived at through the field optimisation process conducted during the test pit excavation. The total swell/displacement percentage (volume after blast/volume before blast) largely determines the diggability of a well fragmented muckpile. Consequently where fragmentation is good any reduction of total swell will probably reduce diggabilty. Any reduction of diggability can and should be traded off against increased gold recovery. In most gold mines, diggabilty will be substantially compromised at the balance which produces the most profit. When these considerations are combined with the cost to drill and blast material, processing costs and the achievement of æacceptableÆ diggibility, the analysis becomes extremely complex and qualitative. Many trends are evident including:the relationship between powder factor (for each blast design) and maximum forward displacement (throw), see Figure 1; and the relationship between powder factor (for each blast design) and drill and blast cost per BCM, see Figure 2. The following blast designs are matched to each of three ore-tonnage alternatives (as supplied by BGM) (Table 1). They are all based on powder factor of 0.62 kg/BCM and are considered optimum from a mining æpoint of viewÆ. The costing of each design includes drilling, explosives and labour cost to load, stem and tie-in holes. Using the available rock data and relying heavily on the wall exposures in the test pit(s), it is the opinion of the author that between 20 per cent to 40 per cent of the final walls excavated in the Wandoo pit would be likely to have the angle between the dominant foliation and the wall plane that is well suited to presplitting and be cost-effectively served by presplit technique. The drilling cost for 125 mm blasthole is about $11.40 per drilled metre and the cost of 40 mm presplit explosive is about $140 per 25 kg (17 metre) case. This implies that the cost to drill and blast presplit on the above parameters would be about $10.90 per square metre of presplit face. The remaining wall area would be most cost-effectively delineated using modified production blasting techniques. This requires the use of modified parameters such as smaller hole diameters, smaller spacing/ burden, higher powder factor, free face firing, less rows per blast and longer delays. These altered blast parameters would usually be applied uniformly across the entire blast fired adjacent to the wall and this ætrimÆ blast would relieve burden away from the wall, into the pit. In simplest terms, this method relies upon maximised burden relief to minimise blast energy applied to the wall. It is only applicable where the material to be blasted is waste since the throw achieved is inconsistent with ore dilution control. The largest charge weight per hole for these analyses is 360 kg and the nearest domestic structure to the proposed Wandoo pit is about 6100 metres distant. From these parameters and assuming a worst case example of rock controlled site factor, the predicted ground vibration is 0.5 mm/sec that is about five per cent of the lower limit set down in AS 2187 part two (1993). This suggests that for the current location of neighbours, ground vibration will not be an issue for the Wandoo operation.

Jan 1, 1999

By Borsaru M, Wylie AW

A neutron irradiation technique has been developed which is suitable for the determinat- ion of the iron and aluminium content of iron ore fines (-6 mm particle size) on a moving rubber conveyor belt. The determination of iron entails measure- ment with a NaI(Tl) gamma ray detector of the characteristic prompt gamma rays (7.64 MeV) due to thermal neutron capture in iron, while the determination of aluminium is based on thermal neutron activation analysis. For the latter a second detector must be placed down- stream to monitor the 1.78 MeV gamma radiation emitted after activation of aluminium. Although conveyor speed has no effect on the Fe measurement, it has an adverse influence on the aluminium signal, and the belt speed should not exceed 0.1 m/s if good accuracy is required. Static trials on a 460 mm rubber conveyor belt with constant ore geometry indicate that for iron an accuracy of ¦ 1.2% Fe (2a) can be achieved for crushed run-of-mine ore at

Jan 1, 1978

Dynamic shocks, which occur in mine hoisting systems have been measured by various investigators over the past 30 years. In 1966 the most intensive analytical investigations were being planned in Bochum, Germany, where equipment then was being constructed to measure the power generated in any particular dynamic shock. Between 1953 and 1956, in Broken Hill, N.S.W., accelerations of the shaft conveyances were measured and analysed. The "effective mass" of the conveyances at the time of the shock was then and still is considered as indeterminate and not easily measured. It is believed that probable peak forces can be determined by the product of the static mass and the accelerations. The subsequent problem of the elimination of the dynamic shocks becomes one of possibly increasing the frequency and thus reducing the amplitude, after identifying and evaluating the shock generators. In addition, judicious use of the clearance between the shaft conveyance and the guide, as a zone in which to absorb vibrations, is a factor which has been overlooked in earlier investigations on This topic.

Jan 1, 1971

By Liu H, Chen S

Natroalunite is one of colouring minerals in kaolin. In this investigation, natroalunite, on which Ca(II) was adsorbed, was flocculated by HPAM and kaolin was depressed in suspension. The adsorption of Ca(II) on the natroalunite surface was studied by zeta-potential measurement and Auger Electron Spectroscopy analysis. Ca(II) was adsorbed more on the natroalunite surface than on the kaolin surface. The mechanism of Ca(II) adsorption was considered to be chemical adsorption on natroalunite and to be physical adsorption on kaolin. It has been found that Na6P6O18 and Na2Si04 can strongly affect Ca(II) adsorption on the surface of kaolin, but weakly on the surface of natroalunite. The effects of degree of hydrolysis and the molecular weight of HPAM, the effect of pH and the effect of Ca(II) have been studied. The kaolin ore, containing SO3 1.05 per cent has been processed with this method. The products only containing S03 0.36 per cent and the weight ratio of concentrate 52.27 per cent were Obtained.

Jan 1, 1993

The sampling of a run-of-mine (ROM) ore with the objective of controlling the fundamental variance associated with the sampling step is a poorly understood subject. Finding the effective sampling constant by repetitive sampling to establish the variance between nominally identical subsamples of a given mass of the ore is a laborious, time-consuming and very expensive exercise. In this paper, the run-of-mine ore is modelled using three components: ore, waste, and relatively fine material which shows significant liberation of the mineral phase(s) carrying the target analyte. The expression for the sampling constant of the mixture is developed from first principles. The form of the equation provides insight into the factors that are important in controlling the magnitude of the sampling constant and hence the fundamental uncertainty associated with a given mass of sample. The controlling factors are shown to be the size distribution of the ore/waste mixture, the proportion of waste mixed with the ore and the extent of liberation and the size distribution of the liberated material in the finer fractions.

Jan 1, 2008

Due to collapsing copper prices during 1974/75, a rapid changeover was made at the C.S.A. mine from mechanised cut and fill stoping with incline access to the more economic long hole open stoping method. In 1974/75, 20 per cent of total production came from open stopes. For the 1976/77 year-to- date, more than 80 per cent of total production has been won from open stopes. As a result, mining performance has improved considerably. Stops, drilling performance has increased by more than 50 per cent since the changeover from extension rod, 50 mm diameter cut and fill uphole drilling to 115 mm diameter in-the-hole hammer drilling of holes up to 65 m long. Stops blasting performance has improved from 750 tonnes to 950 tonnes blasted per manshift. Open stope primary blasting per- formance is much higher, but reduces to 950 tonnes per manshift when secondary blasting and firing of hung drawpoints are taken into consideration. Ground control, the most expensive and least productive aspect of cut and fill mining, is almost entirely eliminated in long hole open stoping.

Jan 1, 1977

The geographical region of South East Asia is variously defined, but generally agreed to include the Asean group - Philippines, Malaysia, Thailand, Singapore and Indonesia. Other regional countries, such as Vietnam, Laos, Burma, Kampuchea etc. are of course geographically part of the region, however in economic terms, they play a minor role. It is the Asean group that dominates present economic activity and provides the overwhelming opportunity for commercial development. My experience in South East Asia has been gleaned over 15 years of regular travel in the region. More recently, we have established company offices in Malaysia, Singapore and Indonesia to extend and deepen contacts with major customers. This progressive development is an integral part of a planned growth pattern and will be discussed in more detail shortly. South East Asia is a rapidly developing economic growth centre, a fact which is clearly recognised and accepted by most commentators. An important question is then to be asked: Why has the region been relatively neglected by Australian, U.S. and European industrial supply companies? I will attempt to address this question in the context of industrial minerals and propose some ideas as to how effective sales programs could be developed. Firstly, let's consider the market potential provided by countries within the region. It is reasonable to suggest that industrial growth in S.E. Asia over the past 20 years has been generally steady and in some cases, explosive. Until recently, this growth has predominantly been driven by development of internal (regional) demand. Population growth and rising living standards have ensured that basic industries have enjoyed a solid uptrend in sales and production. The industries which most benefitted from regional economic development over this period were, interestingly, those which we understand to be major users of industrial minerals - glass, ceramics, paper, surface coatings, cement, refractories, rubber and plastics. Each of these industrial sectors has been influenced by different growth stimulii over a 20 year period. Nevertheless, they also enjoy a common feature which ensured an above average performance. All sectors are fundamental to an environment enjoying rising living standards and rapid growth in general prosperity. More recently, internal growth factors have been overtaken by a recognition that manufactured products from the region are competitive in export markets. This comparatively recent development provides the most interesting possibilities for higher value industrial mineral raw materials. Let me explain: For 20 years, industrial growth in South Asia has essentially been focused on satisfying domestic demand. Finished quality of manufactured items was orientated to a developing market more interested in cost than aesthetics or long life. This was reflected in raw material specifications, which often did not exist and at the best were undemanding.

Jan 1, 1989

By M J. Saynor, J B. C Lowry

The Ranger Uranium Mine is located in the wet-dry monsoonal tropics approximately 250 km east of Darwin in the Northern Territory of Australia (Figure 1). Mining of open-cut ore bodies commenced in 1980 (Pit 1) and ceased in 2012 (Pit 3) and milling and production are scheduled to cease by 2021. At the conclusion of mining and milling operations, mine tailings will be returned to the mined out pits 1 and 3, which must then be physically isolated from the environment for at least 10,000 years (Australian Government 1999). The final landform also needs to have sufficient mitigation measures in place to ensure that areas downstream are not impacted by erosion products from the mine site. The proposed post-mining rehabilitated landform will cover approximately 847 hectares (8.5 km2) which represents an area that has the potential to supply sediment to catchments and streams downstream. One method of reducing runoff and associated sediment is the construction of rip lines along the contour to slow down the runoff velocity and to also trap fine sediment and nutrients in the depressions to assist vegetation growth.CITATION:Saynor, M J and Lowry, J B C, 2018. The impact of rip lines on erosion at the Ranger Mine Site, in Proceedings Life-of-Mine 2018, pp 150–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By S Slusarczyk, Z Kozlowski

Vibration of surface caused by seismic quakes can make a risk to great mining costruction. We have to do with this risk in the Belchatow open cut mine where seismic quakes of various energy and range have occured since the end of 1970s. The seismic risk influence on the mine structure with the special attention to the slopes of an internal dump has been presented. Hydrogeological and geotechnical conditions of the lignite mining and internal dumping of overburden and ash from Belchatow power plant have been considered. Seismic activity in Belchatow open cut from 1979 to 2001 was described and the connection between mine working and seismicity of this area was investigated. The energy and approximate location of the quakes and seismological parameters of the strongest ones observed from 1995 to 2001 were presented. The mechanism of the quake focuses was determined by means of the primary-arriving wave method. Stability of the slopes was evaluated by means of the Fellenius method. It has been found that seismic events occured in Belchatow region may cause only local eboulements whereas there are not any safety risks to the stability of slopes of the internal dump in Belchatow open cut.

Jan 1, 2003

Today's emphasis on the enterprise bargaining process must be seen as an opportunity for organisations to further develop occupational health and safety standards at work. In particular, this shift from a centralised industrial relations system to employer, employee bargaining, presents organisations with an excellent opportunity to develop OH & S at the `shop floor' level. This is despite real difficulties in presenting hard data on the cost benefits. Unfortunately, examination of enterprise agreements ratified by the Australian Industrial Relations Commission (AIRC), show that less than 32 per cent contain provision for occupational health and safety. Those addressing the issues of occupational health and safety have included segments such as: ò rehabilitation activities; ò a new emphasis for workplace occupational health and safety committees; ò formalising procedures related to hazard identification and control; ò the use of personal protective clothing; and ò occupational hygiene and health monitoring issues. For example, an enterprise agreement reached between CIG-Gases and their unions, included clauses which commit employees to attending ten safety meetings and two work place inspections each year, in order for them to receive any further pay rises.

Jan 1, 1995

By H Han, X Wang, T Li, D Duan

"In this paper, the reduction and separation behaviour of iron and slag in carbon composite iron ore pellets has been investigated experimentally using an electric resistance furnace simulating a rotary hearth furnace process. The factors that affect the formation of iron nuggets, such as temperature, holding time, molecular ratio of C/O and basicity, are discussed. Results show that the reduction of iron ore, carburisation of reduced iron and the composition and quantity of slag are very important for producing iron nuggets. Through optimisation of process parameters, iron nuggets can be formed below 1300¦C when holding time is 20 minutes, C/O is 0.7 and basicity less than 0.5. This study provides a theoretical and technical basis for iron nugget production.CITATION:Duan, D, Han, H, Wang, X and Li, T, 2013. Iron nugget production technology in rotary hearth furnace process at lower temperature, in Proceedings Iron Ore 2013, pp 363-368 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 12, 2013