Search Documents

By T Takayama, M Matsumura, Y Konno

The steel industry accounts for 14 per cent of domestic CO2 emission in Japan, and iron ore sintering process occupies approximately three per cent. While Fe content in iron ore is gradually decreasing. So, the amount of concentrated iron ore will increase in the future. We have focused on magnetite concentrate as sinter materials, because magnetite can be easily magnetically beneficiated. However, it is experienced that blending magnetite ore resulted in increasing Fe2+ component in the iron ore sinter, which results in lower reducibility. Therefore, promoting the oxidation reaction from magnetite to hematite in the sintering process is countermeasure for reducibility. In addition, this promotion causes increase of oxidation heat, which results in high sinter strength and reduction of coke. It is assumed that the oxidation of magnetite tends to proceed in the cooling stage, where the oxygen partial pressure increases after the combustion of fine coke, but there are few studies on the effect of heat profile, especially cooling path. The purpose of this study is to design the effective sintering heat profile to promote oxidation of magnetite ore, especially, to investigate the effect of cooling path on sintered ore microstructure. In this study, magnetite ore and magnetite reagent were respectively mixed with calcium carbonate reagent. Then the mixed samples were pressed and formed into cylindrical tablets for simulating the adhesive layer of a pseudo particle. Through examining influence of maximum temperature and cooking rate on oxidation reaction of magnetite, we confirmed that the oxidation reaction of magnetite is suppressed at above 1350°C for maximum temperature, compared to 1300°C. Sintering at lower temperature is desirable because hematite is stable below 1350°C in the Fe2O3-CaO phase diagram.

Nov 8, 2021

By P M. Cepuritis

In hard rock mining, large-scale bulk mining methods such as block or panel caving (BC/PC) and sublevel caving (SLC) typically generate significant surface deformations such as subsidence. Surface deformations need to be considered in the project evaluation and planning stages of cave mines, for example, planning and location of critical underground mine planning infrastructure such as portals, haulage and vent shafts, access roads, or potential damage to existing infrastructure, changes to surface water management, waste dump, stockpile and tailings dam stability, and environmental impacts. Assessing the impact and risks associated with subsidence is a key component in robust mine planning and operations management.

Nov 29, 2022

By Nilmani M, Fountain CR

Injection of gases into slag-melt mixtures produces various zones as a result of bubble formation and disintegration within the melt. The extent of these zones depends on the type of reactor used. When compared with ferrous processes, non ferrous processes are character- ised by large bubbles formed adjacent to the tuyeres, low flowrates and shallow tuyere sub- mergence. These features can result in a greater proportion of reaction occurring above the bath, more refractory wear and tuyere blockage with more splashing. The large bubble zone adjacent to the tuyeres has been investigated using the tech- niques of physical modelling, mathematical modelling and plant trials. Large bubble form- ation in physical models was recorded using a high speed camera and a rapid response pressure transducer coupled to an oscilloscope and data recorder. It was found that the bubble volume (Vb) could be correlated at low flowrates using the single bubble model Vb = 1.378 Q6/5 g-3/5 Deviations from this correlation occurred with increasing gas jet momentum. Plant trials were carried out on a copper converter at Mount Isa Mines during five different charges. Pressure measurements were made through the tuyeres during the slag blow and commencement of the copper blow. The power spectrum density showed that the dominant pulse amplitude occurred at a frequency of approximately 3 pulses/sec. Plant data from this and other converters were correlated using the same relationship as for physical modelling. De- viations occurred due to the state of the re- fractory, bath composition or bath circulation effects.

Jan 1, 1984

By T Horberry

This paper describes work conducted as part of an overall research project that aims to identify current and emerging trends in the development of automation and remote mining technologies, and to provide an operator-centred perspective to the design and deployment of such systems. More specifically, this paper outlines a research and development process being constructed to examine the issues of the human skills and capabilities required to operate or maintain automated/remote controlled mobile mining equipment. A human factors approach presented here, where the focus is upon designing equipment interfaces to fit operators, rather than purely designing and deploying the equipment based on a technology-centred approach. However, the importance of training to help develop the required skills and capabilities is also emphasised.The work built on a full review of the literature about the effects of automation in mining and elsewhere, extensive interviews with different stakeholders in mining automation and recognised best practice regarding designing for the human element in automated systems. The human element research and development process proposed is in four stages, ranging from understanding the tasks involved in both manual and automated equipment operation through to user trials to ensure that the automated systems are acceptable to operators and are fit for purpose.It is outside the scope of the current paper to present the full data collection described by this four stage process, but an overview of what will be collected is presented. As such, this paper focuses on the broad methods being developed, rather than the specific results to be obtained. The ultimate objective is to apply a broad ‘technology assessment’ approach to the design, deployment and evaluation of automated mining technologies, in particular by considering the user-centred design implications of these technologies.

Nov 22, 2011

By R McIlwraith, B Breul

Two case studies are presented in this paper. The first one discusses a roller compacted concrete water supply dam that was constructed in El Mauro in Chile to provide water for agriculture activities downstream of a copper mine during the dry season. The 23 m high dam used a bituminous geomembrane (BGM) as the low permeability upstream facing element on the dam to control seepage through the dam. This is the first time that a BGM has been used in this application. A deep cut-off trench was used to control seepage beneath the dam and through the abutments. This paper briefly presents the design of the dam, including selection of the concrete mix and maximum aggregate size that the use of the Coletanche BGM allowed, and provides details of the construction, quality control and assurance of the installation of the BGM. An ultrasonic apparatus was used as part of the quality control on the BGM seams.The second case study discusses a tailings dam in Cerro Lindo, Peru (near Chincha), where a watertight BGM was installed on the upstream face. Results are presented of the survey done by a consultant on the behaviour of the dam and in particular of the BGM following an earthquake of magnitude 8.1 in Chincha close to the site. These findings on-site were checked by trials in a laboratory in California. Test results are given and explained.CITATION:Breul, B and McIlwraith, R, 2015. Case histories – roller compacted concrete dam waterproofing with a bituminous geomembrane in Chile and a tailings dam in Peru subject to an earthquake of 8.1 magnitude, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 367–372 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By Grady PO

The longwall panels at Clarence Colliery have experienced intermittent sudden weightings on the face that have caused some production delays. These weightings have typically been more severe on the wider faces. A program of surface subsidence and extensometer monitoring was undertaken above Longwalls 4 and 5 to investigate the behaviour of the overburden strata during longwall extraction on two faces of different widths.The monitoring indicated that a dome shaped zone of large downward movement extends up into the overburden strata to a height equal to about the panel width.

Jan 1, 1998

By D W. Wall, J P. Vagenas

Questions of sampling precision and accuracy affect every process plant in differing ways and to differing extents. To address these perceived issues, chemists, metallurgists and engineers are often asked to check their results to confirm their reliability. However, it is not possible to achieve the level of detail required to check every sample, especially if the event has already occurred. No operation has the resources to frequently sample every point in the process for the purpose of verification.One way to address this scenario is by generating a sufficiently detailed comparative data set from a dynamic mass balance simulation of the processing plant. This mass balance uses both sample and plant instrument data to model every flow, while also taking inventory changes and process chemistry into account.The mass balance data can be used to identify any bias present in plant sampling and analysis. It can also be used to verify any unexpected assay results by taking a holistic view of the process. Improving the precision and accuracy of sampling data helps support operational decision-?making and understanding. It also improves the accuracy of the dynamic mass balance used in this process, facilitating further improvements.CITATION:Vagenas, J P and Wall, D W, 2017. The benefits of automated metallurgical accounting for plant sampling, in Proceedings Eighth World Conference on Sampling and Blending , pp 203–210 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

Cleaner Production stands for a proactive and preventive approach to industrial environmental management and aims for process- and/or product-integrated solutions that are both ecologically and economically efficient (æeco-efficiencyÆ). Pioneers in the field were large manufacturing and processing industries in the USA (since the late-1970s), but it took until the early-1990s before Cleaner Production was generally recognised as a valuable approach for large and medium sized enterprises. The application of Cleaner Production in mining and minerals, metals and energy production appears to lag behind other sectors, such as manufacturing and processing. This paper starts with a discussion of the Cleaner Production concept and provides examples of its application from a few selected Australian mining and minerals processing industries. This evidences that Cleaner Production can achieve significant reductions in environmental impact, in terms of reduced waste and emission generation and in terms of conservation of materials, energy and water, while simultaneously reducing operating costs. The paper then investigates a number of key issues pertaining to the implementation of Cleaner Production; ie organisation and management of Cleaner Production activities, effective tools for mastering the Cleaner Production concept as a way of life, and performance measurement.

Jan 1, 2002

By D J. Brake

Faced with the need to improve workplace conditions in both its development and production headings in its existing K1 orebody, as well as its new K Link and K2 orebodies, the Kencana mine in Indonesia took the novel approach of reversing the ventilation on most of its access ramp by outcasting up the ramp to the portal. Working levels were then fed with fresh air via auxiliary fans sealed into the current surface ‘egress’ intake raises (ladderways) or another small surface intake raisebore rather than from fans hung in the ramp as in the past. Outcasting the portal provided a substantial increase in the total mine exhaust capacity allowing fewer levels to be ventilated in series and significantly improving conditions, especially in the most difficult workplaces to ventilate. It also reduced the consequences if there was to be a fire on a vehicle in the ramp. The same system using the ramp as an exhaust is also intended to be used as part of the final ventilation solution for the new K2 orebody which also uses a novel single surface ventilation shaft that is vertically split into separate intake and exhaust compartments using a concrete brattice. Using the main ramp as an exhaust has potential application in many other operations in Australia using surface ramps which otherwise frequently suffer from overuse of series ventilation circuits and poor working conditions at the mine bottom.

Mar 21, 2011

The need for formalised geotechnical reporting has not been fully explored at many operations. With the continuing need to provide safer and more efficient workplaces, the requirement for good geotechnical reporting systems (as with other reporting systems) has become of greater importance.Historically, the risk from rockfalls has been the largest cause of fatal injuries in the underground mining industry. The response of the ground to mining is generally poorly documented at many mines. At Olympic Dam, it was found that the existing corporate hazard and incident reporting (HIR) procedure did not record enough specifics about geotechnical issues. A separate and more specific geotechnical reporting process was set up to address this problem.This paper examines the role that geotechnical reporting plays at the WMC Resources Olympic Dam Mine; from reporting and rectifying day-to-day geotechnical issues that affect the operation to documenting and analysing longer term trends.

Jan 1, 2004

By L. R. MURPHY

This paper gives a general description of mining operations at the Rosebery Mine and a brief account of the older Hercules Mine. The more unusual aspects of the operations, such as the sinking of the inclined shaft, blast-hole experiments, diamond drilling practice, and proposed future developments are described in detail.The following main heads are used:Roseberry- General production Data.General Description of Ore-body, and Characteristics of Ore and Country Rock.Layout of MineMining Methods, Filling, etc.Blast Hole Stoping.Sinking Main Inclined Shaft.Mining Timber. Contract System.Diamond Drilling and Sampling.Surveying.Labour Force.New Developments, Sand Filling and Pumping.Hercules-Situation of Mine.Transport-Haulage and Aerial.Ore Bodies.Stoping Methods.Ore Handling.

Jan 1, 1949

By R Strand, B Usher

Environmental compliance and mine designs are increasingly including assessment of flows and water qualities as a key driver to decision-making over life-of-mine. Integrated site-wide water quality models linked to dynamic water balances have been used for regulatory submissions, feasibility studies, operating mines and mine closure studies. These models, developed in GoldSim, link aqueous chemistry to the physical system of the site-wide water balance. Geochemical mechanisms included are determined from geochemical characterisation and site water monitoring, depending on the data availability at each site. External geochemical modelling using PHREEQC, version 2 (by D?L?Parkhurst and C?A?J?Appelo) and Geochemists Workbench (GWB), (by C?M?Bethke and The Board of Trustees of the University of Illinois) identifies the most important geochemical processes to be included in the model as a series of geochemical mechanisms which include source term loading rates, pH-buffering and equilibration of water quality. Water balance components include seasonal flow variability; waste facility water storage and system lags; run-off variability; milling processes and tailings production as a function of ore types; simulation of automated and scheduled maintenance of settling ponds; water re-routing for water treatment and freshwater demand, usage and storage.Case studies illustrating the use of these models for regulatory submissions and mine feasibility studies in a variety of climatic and regulatory environments show the utility and applicability of these models. Site-specific examples of these models developed by Klohn Crippen Berger Ltd are currently used at operating mines across the world. One of the larger mines where this is used is a mature poly-metallic mine in South America where the model has aided mine managers in understanding how various planned initiatives and potential water options will result in changes to flows and water quality. It is used regularly to inform water and waste management to minimise impacts to the receiving environment as a consideration of both flows and concentrations. The mine has also used the model in support of water treatment design, regulatory submissions and mine closure planning.Further examples of feasibility and operational/compliance assessment in arid and strongly seasonal environments for planning, regulatory and closure consideration of mine wastes and pits have shown the utility and usefulness of these approaches for a range of mining operations at various stages of mine life.CITATION:Strand, R and Usher, B, ?2014. Integrated site water balances and water quality models for decision-making over life-of-mine, in Proceedings Life-of-Mine 2014 , pp 271–284 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By B Rusk, L Corriveau, P Emsbo, R P. Xavier

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Porphyry-Cu (Mo-Au) deposits and iron oxide-copper-gold (IOCG) deposits are both characterised by the presence of abundant halite-saturated fluid inclusions that reflect the circulation of hyper-saline hydrothermal brines. While it is widely accepted that brines involved in the formation of porphyry copper deposits derive from unmixing of moderate-salinity, intermediate-density fluids that exsolve from crystallising magmas, the source of brines that form IOCG deposits remains enigmatic and intensely debated. In this extended abstract, we summarise the fluid inclusion characteristics of both deposit types and present trace element compositional data for halite-saturated fluid inclusions from both porphyry copper deposits and IOCG deposits from around the world.While both deposit types typically contain halite-saturated fluid inclusions, vapour-rich fluid inclusions in IOCG deposits are less common than in porphyry deposits and evidence for fluid immiscibility is rare. IOCG deposits also typically lack intermediate-density fluid inclusions that characterise the deeper quartz-rich veins in many porphyry deposits. Many IOCG deposits contain CO2-only fluid inclusions, a type of fluid not observed in porphyry Cu deposits.Our fluid inclusion compositional data show that most porphyry Cu (Mo-Au)-related brines are dominated by Na, K and Fe and contain elevated concentrations of Ca, Cu, Pb, Zn and Mn up to around the one per cent level. On the other hand, IOCG brines are Na-Ca-Fe-dominated and typically contain far less Cu, Mn and Zn than porphyry brines. In addition to Ca, these fluids are also strongly enriched in Ba and Sr relative to porphyry-related brines. Such compositions are consistent with extensive fluid-rock interaction and/or an evolved sea water contribution to IOCG brines.A sea water or basinal brine source for IOCG brines is further supported by bromine concentrations that are much higher than is characteristic for porphyry-related brines. Porphyry brines have Cl/Br molar ratios of between 800 and 3000, which is characteristic of primary magmatic brines, whereas the Cl/Br composition of IOCG brines is more variable. For example, Na/Cl/Br ratios of most IOCG deposits in the world-class Carajás district fall on or near the sea water evaporation curve (most Cl/Br molar ratios are between 200 and 1000) and are diagnostic of sedimentary bittern brines. A few of the deposits in this district also show evidence of the input of subordinate amounts of magmatic brine. At Ernest Henry, in the Cloncurry district of Australia, most Cl/Br ratios plot close to the sea water evaporation curve, but Cl/Br ratios of up to ~5000 in several samples suggest the input of lesser amounts of magmatic fluids, and possibly evaporite-dissolution-derived fluids. Taken together with geologic constraints, these data strongly suggest that porphyry-type deposits form from the circulation of dominantly magmatic fluids, while IOCG deposits form from large-scale circulation of high-salinity fluids sourced dominantly from sedimentary basins with variable input of magmatic volatiles.CITATION:Rusk, B, Emsbo, P, Xavier, R P, Corriveau, L, Oliver, N and Zhang, D, 2015. A comparison of fluid origins and compositions in iron oxide-copper-gold and porphyry-Cu (Mo-Au) deposits , in Proceedings PACRIM 2015 Congress, pp 271–280 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By D Carroll

Mining of the zinc, lead and silver deposit at the Broken Hill Southern Operations site has been occurring for over 100 years. As a result of this, a significant amount of high-grade ore is now taken from narrow remnant pillars left between old stopes and zones of previously mined ground. Stopes have been filled with either hydraulic fill (also known as ‘sandfill’), cemented hydraulic fill (cemented sandfill), waste rock backfill or a mixture of these fill types.In the last ten years, there has been considerable success mining through narrow pillars where sandfill is exposed in the development face and/or walls using a ‘shell’ support regime, wherein a layer of bolted mesh is sandwiched between two layers of sprayed fibrecrete (25 mm fibrecrete, then mesh and bolt, followed by a final 50 mm layer of fibrecrete). Shell support is also used in very poor, broken, relaxed ground conditions and in areas filled with cemented fill (sandfill with a minimum four per cent cement content).The next stage of innovation has been to develop a technique for mining through old stope voids filled with uncemented sandfill, known locally as ‘contours’ (old cut-and-fill working), an activity where unconsolidated sandfill can run at the face and from the backs. The challenge is to prevent exposed sandfill in the face and the backs from failing before it can be supported.To achieve this, the Southern Operations mine has implemented a technique in which 6 m long spiling bars are used to strengthen and stabilise the sandfill in front of the face. The hollow steel bars are driven in around the heading perimeter in a closely spaced pattern then pumped full of grout. The bars and the grout stabilise the sandfill in front of the face, preventing it from failing into the drive during excavation and prior to further support being installed.A final support system consisting of shotcrete, mesh, bolts and steel girders is installed as excavation progresses. Both the initial and final support systems are essentially passive support systems designed for a low-stress environment (as the stress originates mostly from the mass of unconsolidated sandfill).This process is slow and labour intensive. Fifteen separate cycles of people/machinery are needed to progress one equivalent heading cut (compared to six for a standard fibrecrete- and bolt pattern-supported rock face heading). This slow pace introduces scheduling challenges, but the process opens up parts of the orebody that were previously uneconomical to mine.CITATION:Carroll, D, 2014. Mining through sandfill using spiling bars, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 95–100 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By M Pomery

BHP’s Western Australian Iron Ore Operations (WAIO) move approximately 250 million tons of ore per annum. The magnitude of the constant changes to the terrain models along with the diverse output and presentation requirements of numerous stakeholders presents significant challenges for the geospatial team. This paper describes how the WAIO Survey team use a combination of technology and optimised workflows to capture, ingest, publish and access large data sets for diverse stakeholder requirements. Machine learning for processing of data and the use of web based systems to track and prioritise task allocation of resources will be discussed in detail, in addition to the changes to the traditional roles of surveyors from the use of automation and mobile technology.

Sep 18, 2023

By L M. Lobato, J C. S Seoane, F J. Baars

The Carajßs Province presents several volcano-sedimentary sequences that comprise the Itacai·nas Supergroup. The rocks represent bimodal volcanism, and clastic and chemical sedimentation in relatively unstable basins subject to recurrent structural events with subsidence and volcanism. The Grpo Parß Group represents one of these sequences with mafic volcanic rocks that enclose discontinuous jaspilite lenses, with development of large high-grade orebodies (Fe >65 per cent). This unit is named the Carajßs Formation and presents peculiar characteristics compared to other iron districts in the world, thereby departing from the classic Lake Superior or Algoma iron formation types. Owing to the dense vegetation, lack of outcrops and harsh landscape, the structural analysis of the district can only be accomplished by combination of regional field work, detailed structural work on the open pits, and remotely sensed image interpretation, in this case Landsat ETM7, JERS-1 images and the SRTM digital terrane model. The regional trend of the several sequences of the area is approximately N-S and the structure is dominated by a flattened flexural fold system with axes moderately dipping WNW, intersected by several strike-slip faults subparallel to their axial plane. The Serra dos Carajßs represents an s-shaped synform-antiform pair, herein named the Carajßs Fold. This regional structure is partially disrupted by the Carajßs Shear Zone that divides it in the northern (Serra Norte) and the southern (Serra Sul) Ranges and also probably prepared the terrane with the development of pathways for mineralising hydrothermal fluids forming large high-grade massive iron bodies. Syntectonic granitic bodies played an important role in the structural evolution of the area as well. They caused localised ductile flattening deformation and thermal contact metamorphism in surrounding terranes. The Estrela pluton, for instance, was responsible for the discontinuity of the regional trend between the Serras do Rabo and Leste. The Carajßs Province is regionally the upper crustal product of a very shallowly eroded dome-and-keel geometry of Neo-Archaean volcano- sedimentary units intruded by syntectonic calc-alkaline intrusives and overlying pre-existing infracrustal rocks. The lithostructural data suggest continental-margin back-arc basin development and closure in an oblique collision belt, with N-S shallow crustal shortening, parallel to the inferred pre-existing strike of the stratigraphy.

Jan 1, 2005

By R Talebi

A research project to better understand the rock mass behaviour and the seismic response has been conducted during the design and construction of the 9215 level at the E-Block sector of the Northern Star Kanowna Belle Mine. The research program was undertaken at a tunnel located 1100 m below the surface with the results applicable to feasibility studies on underground mining projects in highstress conditions, where failure can occur very soon after tunnel construction. Semi-circular excavation shapes coupled with the use of de-stress blasting techniques were designed to monitor the excavation in conditions of very high stress. The ground support was designed considering high energy dissipation ground support schemes (HED) as described by Arcaro et al (2021). The results indicate a decreased rock mass demand due to the change of excavation shape. Also, localised reduction in rock mass stiffness was achieved due to the implementation of de-stress blasting. Finally, increased ground support capacity was gained by the implementation of the high energy dissipation ground support schemes. The Kanowna Belle Mine has significant ore reserves at depths exceeding 1000 m below the surface. The results of this research will be used to optimise the extraction of the remaining E Stoping Block at depths exceeding 1350 m.

Mar 29, 2023

By L Clarkson, D Williams, P Redcliffe, F van der Wal

This research presents a snapshot and insight into the trends, patterns, and common considerations identified in the current standing of real-time tailings dam monitoring practice. Based primarily on information derived from concurrent research by the author (in form of a Catalogue of Real-time Instrumentation and Monitoring Techniques for Tailings Dams), challenges and opportunities when transitioning to a real-time monitoring system are discussed. Learnings and key considerations between different monitoring approaches are explored, including themes of limitations and advantages that were observed consistently through global supplier feedback.

Jul 1, 2021

By P Micale

Geological data provides the foundations for the mining value chain. It is used to underpin the modelling and planning and consequently optimise downstream business decisions. However, it is often forgotten or taken for granted. End users often assume the data to be sound without verification. Geological data can be considered a company’s number one asset. Subsequently, the storage, use and management of this data need careful curation and time invested in preserving and protecting it. An established polymetallic mine with 20 000 drill holes could have a data replacement value in excess of $500M at 2020 prices, excluding labour and salary costs. The Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (the ‘JORC Code’) provides guidelines for Public Reporting. Within the code, Table 1 requires discussion around the different types of geological data, its collection and use. What is needed is additional details regarding the validation and integrity of the geological database. A comprehensive guideline specifying minimum geological standards for geological databases has been developed. This expands on the critical points outlined in Table 1 of the JORC Code. This guideline can be used by companies where geological databases are managed in-house or used to assess these services’ outsourcing. This guideline will ensure that geological data is reliable and unadulterated and can be used with confidence. Using this guideline will assist in preserving the investment of geological data in the mining value chain

Mar 22, 2022

By E Taylor, F Lebbing

The $2.5 billion EastLink project is a 39 km tollway and includes twin three-lane, 1.5 km long, undrained driven tunnels with cross passages every 120 m. The hard rock tunnels are being built to avoid passing the motorway through the Mullum Mullum Valley and help preserve the unique flora and fauna in the area. The design of the permanent concrete lining and waterproofing system for the EastLink tunnels was both innovative and practical, to meet the demanding environmental and production constraints of AustraliaÆs largest road project. This paper describes several key aspects of the tunnel design and construction, including: design of fully tanked, permanent concrete tunnel linings for the main tunnels and cross passages to withstand 37 m head of water pressure in combination with potential rock loading in the future;optimisation of the tunnel shape to minimise the amount of reinforcement required and the design of special welded mesh which was developed within manufacturing constraints;100 year design life and durability considerations in every aspect and detail of the design including concrete mix design and stray current mitigation;development of a precast invert solution for the main tunnel permanent concrete lining to enable faster lining construction and to minimise risks to the tunnel membrane associated with fixing reinforcement and construction traffic;development of prefabricated reinforcement details for the junctions between the main tunnels and the cross passages to enable faster construction and minimise risks to the membrane associated with fixing reinforcement; andincorporating the tunnel drainage sump at the lowest cross passage in the alignment, resulting in deep excavation to satisfy the required storage volumes for drainage.

Jan 1, 2008