Search Documents

By I Sheppard, A Hills

This paper describes a multi-lift bench stoping method introduced recently to extract the narrow silver-lead-zinc orebodies at the Isa Lead Mine. Cut-and-fill methods were chief mining methods for the narrow orebodies at the mine over 35 years ago. Benching methods were introduced approximately two decades later, and quickly replacing the cut-and-fill methods. The benching methods had improved both the economy scale and safety of the mining operation. The multi-lift benching method combines a number of bench lifts into a single stope to further improve the operational efficiency. Three stopes in the initial multi-lift benching trials are described.

Jan 1, 2003

By Y Peng, D J. Bradshaw, G Long

As copper reserves deepen, they are becoming increasingly less pure. Penalty elements such as arsenic, antimony and bismuth are occurring in increasing concentrations. Environmental issues with smelters are leading to increases in penalty rates for these elements such that some concentrates may become difficult to sell. Arsenic concentration in Rosebery copper concentrates during 2010 varied between 3000 and 8500 ppm. Arsenic levels above 5000 ppm can preclude import to some customer countries. Optical mineralogy has indicated that arsenic in Rosebery copper concentrates is most commonly associated with tennantite (Cu12As4S13) in solid solution with tetrahedrite (Cu12As4S13). In addition, silver reports to concentrate as freibergite (Cu12As4S13 ). A reduction in arsenic content will therefore lead to a concurrent reduction in the silver content.A literature review by Long, Peng and Bradshaw (2012) indicated that arsenic bearing minerals could be removed using potential controlled flotation. Some success in reducing the amount of arsenic had also been reported using either roasting or chemical depression using reagents such as lime and cyanide. Due to the location of the Rosebery concentrator adjacent to world heritage listed temperate rainforest, the use of a roaster or cyanide was immediately discounted. Lime is already used as a reagent in the Rosebery flow sheet, so could be considered as a potential arsenic depressant.In order to determine a method of separating out the high arsenic bearing minerals, two series of flotation tests were conducted. The first series investigated the effect of pulp potential on the recovery of copper, silver and arsenic minerals; a second series investigated the effect of pH, froth depth and regrind.CITATION:Long, G, Peng, Y and Bradshaw, D J, 2012. Production of a low arsenic copper concentrate at MMG Rosebery, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 347-354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

It is very rare in the underground hard rock environment to find a deposit that is ideally suited to a specific mining method. Usually the irregular shape of the orebody will allow the deposit to be extracted by more than one mining method. During the prefeasibility stage, a number of conceptual mine designs are generally evaluated to see which offers the best method of extraction for the deposit. The selected method is usually based on key decision criteria such as the overall extraction of the orebody, the amount of metal produced annually and the unit cost of production. Often the prefeasibility study document will state that the project has an NPV of æxÆ million dollars. This statement can be made without any quantitative consideration of the likely risks of the mining methods reviewed or the level of confidence in the estimation of the NPV. By assigning a probability of failure to each component of the mining cycle a measure of the risk for each method can be determined. One mining method may provide the highest NPV when it is performing well, however, there may be a higher risk of a major failure impacting on the performance of that method, eg the failure of a mass blast of a crown or rib pillar. This paper will present a flowsheet approach to the use of risk analysis for determining the likely production rates of different mining methods. This framework allows the annual metal output to be estimated and from this the NPV for each method. A level of confidence can be applied to the estimated NPV for each option. An example will be presented on how this technique has been used within the Normandy Group.

Jan 1, 1998

By M M. Pande, M Ishfaq

The effect of aluminium on nitrogen solubility was investigated by equilibrating melt comprising master alloy of Fe-Al with pure electrolytic iron in a controlled atmosphere (pure argon) at 1873 K. Nitrogen in the samples was measured by sampling technique using inert gas fusion absorptiometry. It was found that nitrogen content decreases steadily with aluminium concentration and gradually, becomes close to 1 ppm for very high aluminium steels. Wagner’s second order interaction parameter formalism has been used to estimate the equilibrium constant and interaction parameters. Scanning electron microscopy (SEM) investigation showed, dual-phase inclusions comprising AlN phase surrounding alumina core. The 3D morphology of inclusions was studied by extracting the sample from the top and the central bottom portion of the solidified ingot. A sparse distribution of nitrogen was found for most of the inclusions which manifested the presence of almost pure alumina inclusions with different morphologies and sizes.

Jun 19, 2024

By M Darvall

Magnetite ore blending has yielded signifi cant performance improvements in OneSteel’s magnetite concentrator. The magnetite concentrator beneficiates magnetite ore from the Iron Magnet Deposit and produces concentrate, which is pelletised, then fed to the OneSteel Whyalla blast furnace. Concentrator feed variability severely detracts from the concentrator’s performance, affecting both concentrate yield and grade, which impacts on all downstream processing costs.A coordinated approach has integrated mine planning, geological modelling and grade control, to minimise concentrator feed variability, through effective ore blending throughout the mining and stockpiling process.Mine planning personnel design shots that extend the full width of the orebody and hence across the stratigraphic profi le. Based on geological information contained in block-outs and in consultation with Geology, the Grade Control team allocates material to each primary stockpile, potentially from every stratigraphic domane in the orebody. This ensures primary stockpiles are designed with maximum practical homogeneity and consistency.Using only primary movement, the allocated ore is stockpiled in a layer-cake fashion. The ore is pimple dumped across the width of the stockpile footprint and on completion of a layer, it is dozed flat with an access ramp that allows dumping to commence on the next lift. The primary stockpiles are reclaimed normal to build direction and the magnetite is crushed, all in, to a concentrator feed stockpile.The ore is sampled at the crusher from a falling stream cut. These assay data, are used for benchmarking and control charting the grade and variability of concentrator feed stockpiles. The concentrator feed stockpiles have demonstrated a statistically signifi cant reduction of within pile variation, between pile variation and pile to pile variation, primarily attributable to the development of ore blending. The concentrator has seen sustained, improved performance as a direct result, which translates into lower concentrate cost per tonne and improved yield and quality.

Jul 11, 2011

Dr Eric Bumstead is to be commended for his recent paper on gold analysis, published in the March 1984 Proceedings. It is not often that someone in industry, rather than academia, takes the time to collect and report on such a volume of data, data which is of interest to everyone involved in gold exploration and development.After reading the paper I felt, as a geochemist and as ayer, that there was another side to this whole question of analysis that few people are aware of, i.e. the problem facing a laboratory and how the laboratory can try to give the customer maximum value for money spent.Analyses for gold are carried out for different reasons, depending on the aims of the geologist or metallurgist who presents the samples. These can broadly be separated into three classes, to answer the following questions.1. "Is there any gold in this sample?"2. "Approximately how much gold is there in this sample?"3. "How much gold is there in this sample?"In every case there is a different balance between accuracy and precision, cost and avoiding chemical problems. By "chemical problems", I mean such possibilities as samples containing high levels of sulphides, gold present as tellurides, cyanide being present, contamination with mercury, and other mineralogical oddities, plus problems such as samples containing grease.There is no such thing as one assay to cover all possibilities.Samples in category I come mostly from early stages of exploration.There are often large numbers of samples, their mineralogy is not well known and hence chemical problems could exist, but the explorer wants assays at a minimum level of precision and expects minimum cost. These characteristics do not easily come together, for although the precision required is low, the accuracy required is high at low levels. A small positive result when the true answer is nil could lead to a fruitless search and a waste of money. Conversely, a nil result, when the true answer is a small but significant level of gold, could lead to the passing over of an area that may warrant further work.Because there are conflicting requirements for this type of assay, the methods chosen must be a compromise and different assayers will balance these requirements differently and come to different conclusions. The methods cover sample preparation, assay sample size and variations in assay techniques.

Jan 1, 1984

By Wright S, Jorgensen F. R A

The reaction between lead sulphate and a number of base metal sulphides (galena, sphal- erite, chalcopyrite and synthetic pyrrhotite was studied as a means of desulphurizing lead sulphate containing fumes and residues to levels acceptable as ISF feed. The reactants were mixed with 50% zinc oxide to act as a "basket" to contain the molten products of the reaction and pressed into small briquettes 20 mm in diam. Factors such as temperature, time and the composition of the atmosphere were investigated. Using the PbS/PbS04 system as an example it was shown that the reaction became rapid above 800¦C and that both sulphur dioxide and oxygen in the atmosphere were detrimental to achieving low sulphur in the product. In an inert atmosphere all the sulphides when roasted for 1 h at 1000¦C gave results corresponding to the elimination of more than 95% of the sulphur in the reactants. Leach plant residues were considered for use as the "basket" material. It was shown that the residual sulphide and sulphate components of the residues underwent similar reactions to those experienced by the pure systems.

Jan 1, 1987

By Selby J

South Australia's economic development has relied heavily on the mineral industry. In the late 1840s the rich copper deposits at Kapunda and Burra saved the Colony's economy when South Australia became a world copper producer. Copper lodes developed at Moonta-Wallaroo during the 1860s brought further prosperity when mining activities at Kapunda and Burra were in decline. In addition to those large mines there were many smaller workings scattered through the Flinders and Mount Lofty Ranges producing copper, gold, silver, lead and zinc. Most of the mines of this period were worked by Cornish immigrants who brought their own technology and mining methods with them. These people have left a cultural legacy unique in Aus- tralia. In this Jubilee 150 year (1986) the Department of Mines and Energy, working in conjunction with the Department of Environment and Planning, is helping to preserve and interpret selected historic mining sites, most of which have been neglected since their closure. This work is designed to draw people's interest to mining history by providing interpreted sites for them to visit and to demon- strate the importance of the mining industry in South Australia's cultural and economic develop- Ment.

Jan 1, 1987

By A Batnasan, K Haga, A Shibayama, K Higuchi, H Takeuchi

High silica (SiO2), alumina (Al2O3), and phosphorus (P) contents in iron ore adversely affect the quality of iron products. The removal of those impurities from iron ore is an essential point in further iron ore processing. In this paper, the removal of P, SiO2 and Al2O3 impurities from iron ore by alkaline drying followed by reverse cationic flotation is discussed. The reverse cationic flotation experiments are performed using the iron ore samples without and with alkaline drying pretreatment. All other flotation conditions except pulp pH (4–12) and particle size distributions (-45 to -250 μm) are held constant. A typical collector and frother, such as dodecylamine acetate (DAA) and methylisobutylcarbinol (MIBC), are used in the flotation experiments. Alkaline treatment is conducted before flotation using sodium hydroxide at fixed conditions. The impact of alkaline drying on the performance of iron ore flotation is evaluated based on the removal rates of P and SiO2 + Al2O3, iron grade, and iron recovery compared with the iron ore flotation without alkaline drying (direct flotation). X-ray diffraction (XRD) analysis indicates hematite and goethite are the main minerals in the iron ore, which assays 62.8 mass per cent Fe, 0.232 mass per cent P, 7.1 mass per cent SiO2 + Al2O3 (total) determined by X-ray fluorescence analysis (XRF). Results indicate that a combined approach is more effective for removing P and SiO2 + Al2O3 impurities from iron ore than the direct processing technique because the maximum removal rates of P and SiO2 + Al2O3 are 48.2 per cent and 66.5 per cent from the alkaline dried iron ore when 8.4 per cent and 13.1 per cent from the non-alkaline dried iron ore.

Sep 18, 2023

By T W. C Stambolie

Coalmines, like any other mine, generally involve the classic three-staged approach to mining studies; namely concept, pre-feasibility study (PFS) and feasibility studies (Cusworth, 2012). Subsequent to these studies, and in instances parallel to these studies, the commitment to an environmental impact statement (EIS) is made in order to secure both state and federal development consent. In recent times, the sentiment to both mining and coal is changing whereby the traditional approaches to mine planning and economic evaluation is complicated by evolving environmental legislation, expectations and time frames. It is all too common to take shortcuts in the development of projects in order to create the perception of cost savings and expediting the delivery timeline. Atkins (2016) points out that: boards of so many small to mid-tier mining companies, and a few majors, focus on relentless project delivery too early in the project process, with so little time and effort applied to risk analysis and option development. Unforeseen risks can cost any timeline or budget far more than the effort required assessing and mitigating these. The ultimate risk to any feasible coal project is that of environmental approval and achieving development consent.CITATION:Stambolie, T W C, 2016. A black canvas – planning a greenfield coalmine in New South Wales, in Proceedings Life-of-Mine 2016 Conference , pp 31–35 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By J J. L du Plessis, S Viviers, G Ratner

Escalating electricity costs are one of the biggest operational cost drivers in mining. The trend to use high-powered auxiliary fans delivering increased airflow to meet the dilution requirements of diesel equipment, together with the reliance on ducted systems rather than traditional flow-through systems to ventilate areas, increases the overall energy requirements of ventilation systems. To manage and reduce electricity costs energy management systems can be implemented, inefficient operating units can be replaced and the operation of energy-consuming components of ventilation systems can be optimised.This paper describes the process followed to design and develop an energy-efficient axial flow auxiliary fan. The fan-targeted design was based on static pressure and volume flow rate requirements incorporating higher overall fan efficiencies. A brief overview of the results is given, including the aerodynamic design procedure using computational fluid dynamic (CFD) analysis. The mechanical design criteria used, including stress analysis on the rotor and designs to improve the vibration levels of the fan, are also presented. Through this study it was demonstrated that the aerodynamically designed rotors using profiled and twisted blades improve the total fan efficiency considerably when compared with some of the older-generation fans using cambered plates. The latter were typical in the mining sector in South Africa at the time of the study where average overall fan efficiencies of standard cambered fans less than 63 per cent and some of the older-generation cast aluminium blades have peak overall fan efficiencies of about 65 per cent. Peak overall fan efficiency of more than 80 per cent was achieved by using the described design and development process. Additional benefits are that the fans are quieter due to the better aerodynamic design and have a longer operating life due to reduced vibration levels.In conclusion, the use of CFD to develop fans to deliver the required volume flow at the required pressure allows quicker design turnaround time. It furthermore allows the ventilation engineer the option to specify a specific fan and is not limited to an off-the-shelf catalogue fan. It thus allows engineers to purchase a fit-for-purpose energy-efficient fan. The introduction of reliable fan control systems may, however, still result in the biggest cost benefit for underground mines.CITATION:du Plessis, J J L, Ratner, G and Viviers, S, 2015. Design and development of energy-efficient secondary axial flow fans, in Proceedings The Australian Mine Ventilation Conference, pp 337–344 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By P Card

Some project managers accept unsatisfactory economic evaluation modelling because they are unaware of what constitutes good practice. They tend to leave it to the evaluation specialist or others to decide. The AusIMM has published on its website a draft set of guidelines for technical economic evaluation which will allow these project managers to take control and demand worldÆs best practices.The style of the guidelines is described and the source of a worked spreadsheet example in Excel is given.Economic evaluation in project management is described. A simple test for the acceptance or rejection of evaluation work is offered. The nature of modelling and evaluation in each of the three study phases of concept, prefeasibility and final feasibility are described. Suggestions on the selection of specialists for each phase are given. The three levels of evaluation thinking are described, namely, modelling, valuation and evaluation. Finally the meaning of æfinancial analysisÆ is explained.The conclusion is that æthe role of an economic evaluation specialist is to create models and evaluations for the whole project team to readily understand and use: it is not to create models for his/her own useÆ.CITATION:Card, P, 2012. What project managers must demand from an economic evaluation!, in Proceedings Project Evaluation 2012 , pp 173-176 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By D W. Evans

Research into the dynamic properties of ground support elements continues to grow at a global level, given the increasing importance of this field of application within underground hard rock mining. Measuring the mechanical response of such elements under the rapid onset of simulated rock burst loads forms the basis for this experimental work, typically utilising gravitational drop testing methods. This field of research is fundamentally driven by an increasing need for dynamic performance data, given the constant evolution of rock bolting product designs, materials selection, combination testing and specific application needs based on ground types and loading scenarios. A smaller number of globally recognised dynamic test facilities have predominantly lead research within this arena, typically in association with academic institutes, larger industry groups and government research institutes. However, due to the increasing requirement for dynamic performance data, additional facilities have now emerged in order to satisfy the overall demand for test work. These newer facilities are more typically associated with suppliers to the underground hard rock industry, with experimental designs looking to replicate, at least in part, the work of the primary facilities. For standardisation, repeatability and calibration purposes, the cross validation of test data between primary and secondary facilities becomes an obvious and important consideration across this field of research. This paper outlines the development of a new dynamic drop test facility for testing rock bolts, including the structural design and associated high speed data capture system. Based on the utilisation of identical bolt types, material grades, anchoring systems and decoupled ‘free-lengths’, comparative data has been generated to provide cross validation of the new test facility against data generated by a globally recognised primary facility. The cross validation of data provides increasing confidence in the repeatability and accuracy of the new facility as activity continues towards the provision of further experimental test work.

Nov 29, 2022

By S Bhandari

A model for predicting dust plume dispersion from blasting operations using the Eulerian mathematical algorithm has been developed. This model considers atmospheric stability, and wind velocity and direction for computing dust concentrations at different distances from the blast. Software has been developed which simulates the movement of a dust plume at a given horizontal distance from the blast location and time elapsed after the blast. The concentration of dust is also given in vertical planes. It takes into account ground profile and atmospheric conditions such as temperature, pressure, humidity, wind velocity, wind direction and shear. Experiments were carried out in two limestone mines to calibrate the accuracy of the predictions made by such model. High volume dust samplers were used to collect dust samples. Difficulties encountered in satisfactory dust sampling and quantification of results have been described.

Nov 8, 2011

By G Booth

Whilst communications systems in the mining industry have evolved over the years, the premise remains consistent that reliable communication is vital for safety and operational efficiency. TodayÆs open pit mines are benefiting from advanced developmental efforts based on mesh networking hardware and software technology. This paper highlights Rajant CorporationÆs adaptation of technology, originally developed for the defence and first responder industries, to provide wireless network connectivity in open pit mining applications. Featured is the large-scale deployment of over 300 mobile, meshing access points in the Bingham Canyon Copper mine near Salt Lake City, Utah, the worldÆs largest open pit copper mine. Many companies have positioned themselves, their technology and their product line in the arena of rugged outdoor wireless broadband mesh networking infrastructure. However, Rajant Corporation has combined specialised command and control software and portable networks which offer network extensibility and redundancy that are not available in any other networking solution. Rajant CorporationÆs BreadCrumb« offers unique traits in portability and non-line-of-site networking nodes which intelligently route and broadcast in standard 802.11 protocol. The advantage of RajantÆs solution is especially valuable for users needing equipment moved easily and rapidly into and out of the theatre of operations with uninterrupted network availability. The main differentiators that set the BreadCrumb« network apart from the competitors are mobility (continuous availability), simplicity, ability to properly load balance and power options. In 2007, RajantÆs BreadCrumb« wireless mesh system was selected by the Kennecott Utah Copper Corporation (KUCC), a wholly owned subsidiary of Rio Tinto, as its primary communications platform for operations within the Bingham Canyon Copper mine, the worldÆs largest open pit copper mine. The Rajant BreadCrumb« technology enables KUCC to gain additional operational efficiencies by tracking, monitoring and managing its copper mining operations. The primary goal of using the BreadCrumb« wireless mesh system Kennecott was to streamline its complex mining operations. KUCC required a high number of moving wireless nodes for improving mine monitoring and control. The Rajant InstaMesh« software running on the wireless BreadCrumb« units connects hundreds of devices to each other while rapidly transporting critical operational data. Kennecott has successfully implemented a large number of BreadCrumb« radios in an interconnected network that allows loader trucks, shovels, pumps, laptops and other production equipment to communicate with each other in real-time. These systems are a mix of secure access nodes that enable data and voice communications across a meshed, self-healing network for fleet dispatch, health monitoring and other critical mining applications. Many of the devices that require wireless communications are moving at all times throughout the wireless mining infrastructure. The BreadCrumb« nodes rapidly adapt to any changes in the network topology, assuring that IP traffic uptime and bandwidth are maximised. The installation layout and data network specifics, as well as maps and data network efficiencies will be detailed in the paper.

Jan 1, 2008

By A M. Lechner, V Glenn, M Edraki, D R. Mulligan, C Unger

With more than 50 000 recorded abandoned mines in Australia, effective management strategies are needed to prioritise and manage health, safety, environmental and socio-economic risks and opportunities. This paper reviews international leading practices for abandoned mine management and identifies key issues that need to be addressed in the Australian context. As well as the academic literature, this review draws on a 2008 global legacy site survey and forum in 2008, a Churchill Fellowship study of abandoned mines and the recently released æStrategic Framework for Management of Abandoned Mines in the Minerals IndustryÆ (MCMPR/MCA, 2010).A conceptual model was developed to identify the relationship between key issues affecting the management of abandoned mines in Australia. The conceptual model is then used in the development of a maturity chart which draws on risk management principles to provide leading practice guidance for abandoned mine managers, jurisdictions and stakeholders. The maturity chart approach for risk management has been successfully used elsewhere to evaluate safety, environmental and socio-economic maturity.CITATION:Unger, C, Lechner, A M, Glenn, V, Edraki, M and Mulligan, D R, 2012. Mapping and prioritising rehabilitation of abandoned mines in Australia, in Proceedings Life-of-Mine 2012 , pp 259-266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By C Jones

When the Paulsens operation was poised to be placed on care and maintenance, Bill Beament and the rest of the Northern Star Resources (NSR) team capitalised on the opportunity to send the Ashburton region’s only operating gold mine into the record books.A three-stage strategy was devised by NSR to pay off the acquisition and maximise the return from the operation. The first stage was to mine the 55 000 oz mine plan and pay off the cost of the acquisition, then maintain profitable production beyond the seven months and re-establish a mine life. The second stage involved an early commitment to a 220 m long diamond drill drive being placed in the hanging wall of the orebody from which the extensions of the orebody could be further explored, allowing the second stage of the plan to come into effect and extend the mine life by converting Inferred Resources into the mine plan. The third stage of the initial plan was to utilise this drill drive and continue to drill deeper holes beyond the current limit of drilling in the ore zones to extend the orebody and increase the mine’s life.With an ever growing desire to further expand, the young company took on the bold move of establishing its own mining services division. A critical element to the success of this was ensuring that the right people were recruited with the appropriate specialised skill sets.Aligning common goals amongst all NSR team members, from the board and senior management to the work force on site, was critical to integrate the new and driven direction that Paulsens had adopted. It was essential to change the focus and a shift in all employees’ attitudes and values from a mine that was all but down and out, to a site that wanted to be kicking some serious goals.Teaming together a passionate and driven leader with a strong allied workforce was always going to put NSR in the best position possible to make Paulsens the success story that it now is. But without the calculated risks and enthusiastic attitude, the little known mine site in the Pilbara might have remained just that.CITATION:Jones, C, 2014. The Paulsens transformation – a shining light under a northern star, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By T B. T Nguyen, L Matthews, D O’Dea, T Honeyands, T Harvey

Productivity and fuel consumption of the blast furnace is driven by the quality of the iron ore sinter, which in turn is related to the sinter mineralogy. The sintering conditions including temperature and gas composition have a significant influence on the formation of melt and finally the mineralogy of the sinter. In this work, analogue sinter tablets were produced from iron ore fines in a laboratory furnace with tightly controlled temperature profile and oxygen partial pressure in the gas. The mineralogy of the sinters was analysed using reflected light microscopy. The results showed that increasing thermal enclosed area (area enclosed by heating and cooling curve above a reference temperature) reduces primary hematite and platy silico-ferrite of calcium and aluminium (SFCA) contents. This is attributed to increasing melt formation, leading to greater assimilation of the iron ore particles. Lower magnetite was found for tablets with greater median pore size, which is thought to be due to greater oxidation of magnetite to hematite during cooling in air. It was also found that higher alumina content was found to result in more SFCA formation under the same heating/cooling conditions, whereas tablets with higher goethite had higher assimilation and produced more secondary hematite on cooling. Finally, it is necessary to relate the enclosed area to the temperature at which the melt formation becomes significant which strongly depends on chemical composition of the ore studied.

Nov 8, 2021

By P M. Dight

Shotcrete usage in declines and developments has become pervasive as operators strive to achieve production improvements. Issues of mix control, fibreload, thickness control, temperature and curing conditions all play a part in the quality control. Often to overcome some of the quality control issues designers over specify the strength requirements in order to meet their operational constraints. Adherence to the standard civil testing requirements of 28 days moist cured at 21ºC without properly calibrating these results to the changing environment underground leads to contractual disputes. There are a number of standard tests specified including cylinder tests, cored tests, beam tests and round determinate panel (RDP) panel tests. The logistics of storing these samples and then transporting them to concrete testing laboratories without due regard to temperature changes with time can influence the results. All the samples can be readily handled by personnel except the RDP panel. The standard RDP panel is 800 mm diameter by 75 mm thick and requires an ITH machine at the mine and a fork lift at the laboratory to move it around. This paper will examine the possibility of a panel which provides scalable results to the standard RDP panel but can be easily handled by personnel and/or tested on site with suitable equipment. This allows for faster turn around and better quality control for the sample prior to testing. This enhances the identification of quality control issues at the mine and improves safety.

Mar 21, 2011