Search Documents

By A Smith

Rock masses usually exhibit scale dependent mechanical properties primarily due to presence of discontinuities and their inhomogeneous nature. One of the essential preconditions for selection of appropriate strength and deformation parameters of a rock mass in relation to tunnel design is assessment of the scale of the joint network relative to the scale of excavation. In tunnel design practice, scale effects are estimated indirectly using small-scale unconfined compressive strength (UCS) tests and rock mass classification based empirical correlations. Large-scale UCS tests have the benefit of direct assessment of anisotropic and scale dependent properties of a rock mass.This paper presents results of a large-scale UCS test on a jointed siltstone. A 450 mm diameter sample with inclined bedding planes was cored and tested in uniaxial compression until failure with load and displacement measurements. The aim of the test is to determine strength and deformation parameters and correlate them with results of small-scale UCS tests of the same sample. The relationships between the small-scale and large-scale rock mass parameters were validated against published correlations from the literature.

Mar 8, 2011

By S Coward, C Xu, P A. Dowd

"This paper provides an assessment of the current challenges in strategic mine planning and design and suggested approaches for addressing them. The specific challenges covered are: realistic quantification of downstream processes applied to orebody models to provide an integrated approach to mine design and optimisation modelling, estimation and simulation of geometallurgical variables and their integration into resource and reserve estimation and mine planning modelling, estimation and simulation of new variables for new forms of mining – deep mining, particularly block caving, and solution mining flexibility in planning and design to manage risk and minimise its impact information technology (IT) infrastructure and platforms for rapid online data collection, storage, access and processing.Most of these challenges require new types of data, variables, modelling and estimation methods. Foremost among the new types of variables and data are geometallurgical and dynamic rock mass characterisation variables. New types of data and data collection include rapid generation of very large amounts of online sensor data and the consequent need for rapid processing and modelling of these data.This paper outlines the challenges and strategies in each of these areas and uses examples of models and outputs to illustrate approaches and potential solutions.CITATION:Dowd, P A, Xu, C and Coward, S, 2014. Strategies for mine planning and design, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 41–50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By M W. N Buxton, M T. Bootsma, J Benndorf, C Alford

Research in the field of cut-off grade optimisation has shown a relationship between cut-off grade, project life and net present value (NPV). Lane’s theory demonstrates that cut-off grades can be optimised in order to maximise project profitability. Although the theory forms the basis for many open pit mining projects, application of the theory in underground mining remains limited to-date. The main reason for this is the complex interaction between all processes in underground mine planning, which makes it difficult to apply Lane’s mathematical optimisation approach.Recently a new stope optimiser product was released. The AMS Stope Optimiser automates the design of underground stopes at user-defined cut-off grades and allows for rapid evaluation of mine designs at different cut-off grades. Using this software, an optimisation approach was developed and validated on an underground gold deposit in northern Sweden. Potential project NPV increased by approximately 30 per cent when using this new approach.Spatial grade uncertainty in mineral resources was identified to be a major risk in underground stope design. The optimisation approach was further extended to account for grade risk using estimated and stochastic simulated resource models. The resulting optimisation process accounts for grade risk early in the design process and reduces the risk of a stope not meeting the cut-off grade with subsequent financial loss.CITATION:Bootsma, M T, Alford, C, Benndorf, J and Buxton, M W N, 2014. Cut-off grade-based sublevel stope mine optimisation – introduction and evaluation of an optimisation approach and method for grade risk quantification, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 281–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By G M. Volkmann

Pipe umbrella support systems – also called canopy tube systems – have been used successfully for tunnelling in challenging ground conditions since the 1970s. Historically, the drilling unit was the limiting factor for pipe umbrella installations – less attention has been paid to pipe couplings and their influence on labour time and load-bearing capacity.This contribution investigates the influence of the type of pipe connection on the load bearing characteristics of a connected pipe and discusses associated influences on design calculations and installation performance. Standard thread connections reduce the effective cross-section and thereby load-bearing capacity in the connection area. To achieve design parameters, over-dimensioning of the un-weakened pipe section is the only way to overcome this limitation. Recently, two new, alternative connection types were designed and developed for connected pipe umbrella pipes. The first one is the nipple coupling, consisting of fitting with a threaded connection that is pressed and welded into the ends of standard tubes. The second type is the squeezed connection, which mechanically connects non-threaded pipe ends, achieved by force-fitted squeezing from the drill rig. Both coupling types have technical as well as operational advantages compared to the common thread couplings, which are the weakest point in the support system.In the following sections significant technical differences are explained, design values given and a site example presented to illustrate the operational advantages of the newly developed coupling?type.CITATION:Volkmann, G M, 2014. Development of state-of-the-art connection types for pipe umbrella support systems, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 333–338 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By G Hill, D Grant, M Tyler

Located approximately 570km NNW of Adelaide in South Australia, the Olympic Dam mine (OD) is the world’s fourth largest remaining copper and gold resource and the largest uranium resource. Discovered in 1975 and going into production in 1988, the operation consists of a fully vertically integrated underground mine, mineral processing plant, copper smelter and refinery, as well as associated infrastructure. BHP achieved production of 203,000 tonnes of copper cathode plus associated by-products in financial year 2016. The immense size and high-grades of the Olympic Dam resource offer a range of growth pathways, making closure timing estimation and planning a challenge. Current estimates put the OD resource at approximately 79 million tonnes of copper. Major factors influencing the closure timing estimation, as a result of the large resource and grade tonnage profile, include the mining method that may be used and the downstream processing method, ultimately influencing such things as the total disturbance area and the extent of infrastructure to be demolished at the end of mine life. In addition, factors such as the mining and processing method and production rate have a direct impact on larger rehabilitation items such as the total number of tailings cells required.CITATION:Grant, D, Tyler, M and Hill, G, 2018. Olympic Dam mine closure planning process, in Proceedings Life-of-Mine 2018, pp 43–45 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By S Sullivan

A recent review of resource reports lodged to statutory bodies found geological models with oversmoothed or unrealistic lithological boundaries, many of which do not represent geological appearance in the field, pit or underground drive. The underlying data is often too complex or messy to be incorporated into the resource model and is thus a simplification of reality, to the detriment of the mining operation and its shareholders. Volumes can be over- or underestimated and subsequent grade predictions can be misplaced, combining to cause over- or understatement in resource reporting to stakeholders and statutory authorities. Domain models can be improved with new modelling techniques such as machine learning. However, with poor data or improper use of machine learning techniques, the conclusions can be just as misleading as with current techniques. Machine learning rarely offers a single ‘right’ outcome, rather a range of possible outcomes from the data provided. But importantly it can take advantage of the full richness of data for more informed models. Machine learning also provides confidence in its predictions so that uncertainty in the resultant models can be quantified and passed through for risk assessment during mine planning and operation. This paper will discuss the factors accentuating complexity in deposit modelling: data diversity, structural controls, chemistry, data volumes, process workflows and external non-geological constraints. A case study illustrates the risk of reducing or ignoring complexity, which can result in an overly simplified geological model.

Mar 22, 2022

By M Yahyaei, F Vos, J Siliezar

Site-based case studies (including data collected from industrial surveys) and their application in evaluating circuit performance, have a significant role in developing reliable process models. Such models are useful to both plant metallurgists and researchers. Appropriate process models enable the plant metallurgist to assess the impact of different operational parameters on the overall circuit performance. They also provide the researcher with a detailed understanding of process behaviour in response to changes in ore characteristics and process conditions (ie plant throughput, ore competence, ore type). Thus enabling the identification of effective operating factors, and allowing them to be ranked in order of their influence on the process response, which eventually develops into a process control tool in the hands of plant operators.The above approach has been developed and applied at the Julius Kruttschnitt Mineral Research Centre (JKMRC) separately for both comminution and flotation processes. In recent years, the JKMRC has attempted an integrated approach by developing process models that incorporate the impact of upstream processes on downstream processes. This is not possible using the traditional approach of separate comminution and flotation surveys, so conducting integrated plant surveys is crucial for success in developing integrated process models. This paper summarises industrial experience gained while conducting such an integrated plant survey at Glencore’s Ernest Henry Mining operation near Cloncurry in north Queensland. An appropriate approach should be taken to enable the alignment of different requirements from different processes during the plant survey. This, as well as the challenges faced in integrating comminution process models with flotation process models, are identified.CITATION:Yahyaei, M, Vos, F, Powell, M S, Siliezar, J and Perkins, T, 2014. Challenges in developing integrated process models based on industrial survey data, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 437–446 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By N Herault

PT Freeport Indonesia recently completed preproduction development and construction of the Big Gossan underground copper and gold mine, located in the Ertsberg mining district of Papua, Indonesia. Production has commenced with an expected ramp-up to full production of 7000 tonnes per day in 2012. The Big Gossan utilises an open stoping mine method with paste backfill.In order to deliver ore to the mill, which sits in a valley above the ore deposit, an underground production shaft and hoisting facility was designed and constructed as the key component of ore haulage. The design and construction of the Big Gossan shaft posed many challenges to the project team. Available shaft design and construction expertise were limited as this was the first shaft of its kind in Indonesia and the project was undertaken during a time of high industry demand for new shaft systems. Construction resources were also limited due to the remote location and competition with existing, producing mines for these resources and skills. The project also taxed the ability of Freeport to provide services and resources to this as well as their other projects.Completion of the Big Gossan shaft was a milestone in PT Freeport Indonesia’s plan to fully transition ore production to the underground environment in this decade.This paper deals with the various challenges faced by PT Freeport Indonesia and shaft contractor, PT Redpath Indonesia, during the construction of the Big Gossan shaft and offers suggestions to improve future shaft projects of a similar nature.

Mar 21, 2011

By G S. Beros, K M. Edwards

Over the past 20 years drum scrubbers have become a widely adopted technology within iron ore beneficiation plants. Generally, the drum scrubbers in use are considered high-capacity machines capable of accepting larger-sized feed material. Together with a water addition to a desired pulp density and a mild energy input, these large rotating machines effect an attritioning action that removes water soluble clays and other deleterious materials. Within the Western Australian iron ore industry, drum scrubbers have been successfully applied to Channel Iron, Marra Mamba, Bedded and Detrital orebodies. The introduction of drum scrubbers has enabled Western Australian producers to satisfy the substantial increase in demand for iron ore from Chinese steelmakers by making the lower-grade sections of the above orebodies economic. However, despite being a relatively simple unit process, the requirements for successful design and operation of these machines are not fully understood. This paper draws on the collective experience of both authors to provide some points to consider for incorporating drum scrubbers into iron ore beneficiation plant flow sheets.

Sep 18, 2023

Adsorption Behaviours of Humic Substances onto Iron Ore Particle Surface Humic substances extracted from lignite mainly consist of fulvic acids (FA) and humic acids (HA), which have been successfully used as good composite binders for iron ore pellets in laboratory tests and industrial production. However, there exists a general lack of understanding of the interaction between humic substances and iron ore particles surfaces. In this research, by means of zeta potential measurements, Fourier Transform Infrared (FTIR) spectrum, colorimetric method and Environmental Scanning Electron Micrograph (ESEM) imaging, the adsorption behaviours of FA and HA onto the surfaces of iron ore particles are investigated. The zeta potential results indicate that adsorption of FA on the iron ore particles can be characterised by specific and electrostatic interactions, while adsorption of HA is by electrostatic and chemical adsorption interactions. FTIR spectrum results show that adsorption force of FA on the iron ore particle surfaces is stronger than that of HA. From results of colorimetric method, compared with HA, adsorption amount and adsorption rate of FA is more and faster, respectively. FA molecule presents on the surface of magnetite in the shape of an araneose network structure according to the ESEM images, while HA molecule appears on the surface of magnetite in the form of small flocs or microclusters. Humic substances are effective to iron ore pelletisation. Comparsion of agglomeration results show that the different mechanisms of adsorption result in varied agglomeration behaviours. Theses findings above would be beneficial to the implications of composite binder for agglomeration.  

Sep 13, 2010

By M J. Nugus

The structural models developed by exploration and mining geologists are most commonly concerned with the ‘main structures’ or key constituents that pertain to the associated mineralisation. To this end, it is recognised that the geological and exploration models, which are developed, are essentially ‘fit for task’ and the scale-related variances are not always realised at an early stage. In fact, in many cases anomalous intercepts along different trends and of variable apparent continuity have often been neglected as ‘back scatter’ and not important. Recognition of the importance of subordinate structures as mineralising hosts suggests that additional opportunities exist outside the primary and main structures. History shows that opportunities are often not realised where gold is hosted in orientations not parallel to the predominant trend of the schistosity, main fault or shear zone.Another reason for the importance of subordinate structures can be understood from their roles in a percolation network. Subordinate structures can access the large fluid fluxes provided by backbone elements, but, as dangling elements, they provide greater opportunities for gold precipitation mechanisms and hence may constitute essential parts of the resource. Therefore, the role, understanding and consideration of the smaller-scale and orthogonal structures should be considered during all facets of exploration, resource development, delineation and mining.

Aug 22, 2011

By R Austerberry, S Green

The discovery of the Cuffley Lode at Mandalay Resources Costerfield Operations provided an opportunity to extend mine life via mining the offset depth extension of the previously worked Alison Mine. Access from the existing Augusta Mine placed the initial Cuffley underground workings at approximately 250 metres depth from surface. As the new orebody transitioned towards production, a secondary means of egress needed to be established. The depth of the initial capital development presented a challenge in establishing a secondary means of egress that could be confidently relied on. The availability of land to locate a surface shaft collar further reduced available options and geotechnical drilling further limited suitable shaft locations. Time limiting factors such as permitting and having a secondary means of egress in as soon as possible, further highlighted that an innovative secondary means of egress was needed. A consideration of using an emergency gig lowered by a suitable sized crane supplied by an external crane contractor was investigated and found to be a suitable outcome. This Emergency Gig was deployed via the Cuffley Return Air Raise. When trialled, the emergency gig was found to provide a reliable, repeatable extraction method with an acceptable level of risk. Issues discovered during such trials further improved the process to a point where this extraction method became the adopted secondary means of egress for additional lodes that existed at depth. When assessing possible methods of secondary means of egress, the use of a third-party crane and custom designed and fabricated emergency gig should not be discounted. Where a crane can be sourced within an acceptable timeframe, the emergency gig extraction method provides a reliable safe and cost-effective means of secondary means of egress, especially when multiple shafts are to be developed. Local laws may negate the ability to employ such a system, although it is believed with good communication and well-constructed risk assessments, this system can be safely deployed.

Mar 15, 2021

By S Farrokhpay, C Akop

Copper-gold-pyrite ore types with an elevated pyrite head grade utilise a sequential flotation circuit to recover initially a copper-gold concentrate with a pyrite-gold concentrate being produced from the tailing of the initial circuit.A simpler flotation circuit with lower operating and capital costs for treatment of such copper-gold-pyrite ores with an elevated pyrite head assay was sought in the described work. After characterising the ore, the objective was to apply bulk rougher flotation of both the copper minerals and pyrite for the copper-gold-pyrite ore at natural pH. Hence, no lime or other pyrite depressants were required in bulk roughing. The bulk rougher concentrate was upgraded in a cleaner circuit to reject non-sulfide gangue and then the resulting sulfide concentrate was separated by depressing the pyrite to produce two products (copper and pyrite concentrates, both having significant gold assays). A standard test with a sequential circuit was applied to the same ore for comparison.The chalcopyrite and pyrite losses in the tailing from the rougher circuit were the same for both bulk and sequential roughing (less than six per cent). In cleaning (bulk circuit), the effective pH for pyrite depression was 11.8–11.9; copper recovery was 70–75 per cent (grade of 15–20 per cent copper) and the sulfur recovery (pyrite product) was 80–85 per cent (grade of 34–36 per cent sulfur).These results approached those for the sequential circuit where copper recovery was 80–85 per cent (grade of 15–20 per cent copper) and the sulfur recovery (pyrite product) was 83 per cent (grade of 38 per cent sulfur).The observed effects of feed sizing on the liberation of minerals in the rougher feed are discussed. Options for improving the bulk circuit results are also considered. Importantly, the implications of various aspects of these findings for the bulk circuit are discussed with an industrial focus.CITATION:Akop, C, Farrokhpay, S and Johnson, N W, 2014. An alternative circuit for chalcopyrite-pyrite ores with elevated pyrite content in Cu-Au ore treatment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 407–416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By N Kawashima, R St C Smart, A M. Robertson

This paper focuses on a case study at a base metal mine located in a tropical semi-arid area of Western Australia (WA). It is demonstrated that understanding the geochemical nature of the mine tailings forms an integral part of innovative management strategies developed throughout the life-of-mine (LOM) when planning for mine closure. The tailings are currently stored at an above-ground valley fill tailings storage facility (TSF) and one option for long-term management under consideration is leaving the tailings in situ at mine closure and covering using the concept of an enhanced æstore and releaseÆ cover system.Extensive geochemical and mineralogical studies have found that the geochemical behaviour of the tailings in the TSF is significantly more benign than initially predicted. The sulfide content of the tailings is primarily pyrrhotite, which can be acid-forming, acid-neutral or acid-consuming depending on a number of factors including redox conditions. Tailings pore water at depth is pH neutral with excess alkalinity, low concentrations of dissolved metals and elevated sulfate concentration.Recent geochemical tests on tailings samples indicate that a reduction in the acid potential and a corresponding increase in the neutralising potential of the tailings, through partial removal of pyrrhotite at the ore processing stage, has the potential to further reduce the long-term risk of potential impact to the environment from any TSF seepage. The current work program investigates whether partial removal of pyrrhotite is feasible and secondly, whether this approach is necessary to produce a significantly better outcome at mine closure.CITATION:Robertson, A M, Kawashima, N, Smart, R St C and Schumann, R, 2012. Understanding tailings geochemistry - Continuous learning and innovation when planning for mine closure, in Proceedings Life-of-Mine 2012 , pp 287-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By G Pizarro, O Miranda, D Rosales

In panel/block caving mines, large amounts of information are collected at the operations. This information includes grades and extracted tonnage, fragmentation, lithology, design of stopes and main infrastructure, geotechnical information, overbreak progress, seismicity, numerical modelling and many other mine variables. To improve the reliability of the production plan it is required to integrate the mine data into one platform. In this paper, the logic of a new technological platform is presented for analysis, modelling and design in panel/block caving mines. The platform includes an acquisition system for mine data and geotechnical information, a back-analysis module for calibrating statistical models and a module of visualisation of the results. The application and benefits of the platform is illustrated for mining induced seismic risk for panel/block caving mining operation. The platform can be used in the mine design and planning processes and is useful for reducing uncertainty in the mining business of panel/block caving operations.CITATION:Miranda, O, Rosales, D, Pizarro, G and Vallejos, J, 2016. Development of an integrated platform for the analysis, modelling and design in panel caving mines, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 237–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By G M. Jeffress, D C. Arne

There are two discrete aspects to collecting portable X-ray fluorescence (pXRF) data to obtain reliable results and to comply with reporting requirements under the 2012 edition of the JORC Code (JORC, 2012) – sampling method and quality assurance. A robust sampling program is required to obtain representative material for analysis. The appropriate method should be established for a particular project using a small orientation study. A variety of approaches to sampling soils, drill cuttings, rock faces and diamond drill core are discussed. These include using multiple spot analyses, scanning using a single operating beam and the collection of cutting saw pulps. The operator must also be aware of the attenuating effects of analysing through sample bags of different material types for various elements as well as the limitations of current pXRF instruments in reporting reliable data for certain elements. The analysis of the samples must also be accompanied by a quality assurance program in order to generate data that are ‘fit for purpose’. This includes recording X-ray tube resolution on a routine basis, using matrix-appropriate standards for which total elemental concentrations are available, using silica blanks, capturing sufficient duplicate analyses to constrain data precision and obtaining check assays to calibrate pXRF data against laboratory data. Examples of quality control approaches and data are presented. Table 1 of the 2012 JORC Code also recommends that information on instrument make and model, reading times and calibration be provided in any reporting of pXRF data. To this should be added information on operating mode and temperature, software version and moisture content of the samples. A robust sampling methodology with a suitable quality assurance/quality control program should produce pXRF data of sufficient quality for public reporting purposes, provided that the data are presented using appropriate cautionary language and adequate supporting information.CITATION:Arne, D C and Jeffress, G M, 2014. Sampling and analysis for public reporting of portable x-ray fluorescence data under the 2012 edition of the JORC Code, in Proceedings Sampling 2014 , pp 57–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By D Teyhan, J Kirsch

Traditionally, most Australian iron ore mining operations have been surface-based. Processing plants were designed to handle dry ores. In recent years mining operations in the Pilbara have progressively moved below the water table exposing wet, sticky ores which have caused lost efficiency in screening operations as particles tend to agglomerate and adhere, blinding screening media. Miners and vibrating screen manufacturers have experimented with a shift from linear motion to elliptical motion screens. Elliptical motion conveys and lifts particles. Effective on flat deck (horizontal and inclined) or sloping decks it can be configured to provide a controlled transport rate, applying pressure in all directions to maximise screening efficiency. In practice, elliptical motion screens have proven to be effective in dislodging sticky particles from screening media, reducing blinding rates and improving screen efficiency. Moisture and clay content change during the life of a mine. These changes are sometimes the effect of seasonal rainfall, in other cases due to increased groundwater and clay content as mining operations go deeper. To compensate for such changes and optimise screen efficiency, changing the ‘shape’ of elliptical screen motion is required. This has traditionally required shutting down processing plants and making mechanical screen adjustments. Plant downtime is costly and machine adjustment has been a ‘trial and error’ practice. This paper will explore the results of a field trial that is currently underway in Brazil of a next generation elliptical motion screen design that allows operators to make changes to exciter rotational direction, speed and screen stroke angle, through electronic drive phase control. The machine’s electronic drive system synchronisation is enhanced for stability with a unique mechanical timing system. Operating at up to 6 g, screen adjustments can be made on the fly without stopping production. Early trial results are showing up to 50 per cent improvement in screen efficiency compared with traditional elliptical motion machines under certain feed conditions.

Aug 24, 2022

By B J. Monaghan, R J. Longbottom, D J. Pinson, S J. Chew

Recycling steel plant by-products is a critical issue for achieving both environmental and economic sustainability of integrated steel plants. A key steel plant by-product stream is dust from basic oxygen steelmaking (BOS), which can be recycled back to the BOS vessel as iron units and to aid slag formation. The major limitations for its recycling are zinc and the uncertainty in zinc speciation of the dust. This uncertainty affects the amount of dust recycled and how it interacts with the slag during processing. BOS dust in stockpiles can undergo self-sintering reactions that oxidise the iron-bearing components. As this occurs, zinc (or oxide) may combine with iron oxides to form a zinc-iron spinel solid solution phase. Knowing which zinc-bearing species are present in the BOS dust is a key aspect in understanding and developing an efficient recycling process for the dust. To overcome difficulties associated with phase identification in the BOS dust (both fresh and selfsintered), particularly the magnetite-zinc ferrite spinel solid solution using X-ray diffraction (XRD) / scanning electron microscopy (SEM) / energy dispersive spectroscopy (EDS), high end characterisation tools, transmission electron microscopy (TEM) and Mössbauer spectroscopy, were also used. Such an approach allowed improved phase identification of key zinc- and iron-bearing phases that were not previously resolvable. The zinc in fresh BOS dust was mostly present as extremely fine separate particles of zinc oxide, attached to the iron particles. These extremely fine particles were <10 nm in size. Additionally, a small amount of zinc ferrite was also identified within the sample (most likely contained within a magnetite-zinc ferrite spinel solid solution). However, the zinc in the self-sintered BOS dust, was found to be present entirely in a magnetite-zinc ferrite spinel solid solution. While this spinel phase had been previously identified by XRD, it was not clear that it contained zinc. The Mössbauer results provided definitive evidence of zinc within the spinel phase.

Jun 19, 2024

By B Wong, R G. Coleman

In flotation, the selection of the size, number and type of cell for a particular duty depends on two important factors. Firstly, the required flotation residence time and secondly, the physical constraints of how much concentrate can be recovered for a given froth surface area and concentrate lip length. The residence time is influenced by ore type and characteristics such as liberation, kinetics and reagent dosage. The amount of concentrate that can be recovered for a given froth surface area and lip length depends on ore type and other characteristics such as particle size, specific gravity and mineral grade. Residence time is determined through a combination of laboratory-scale test work and design scale-up factors. However the critical froth transport parameters such as froth carry rate and froth lip loading cannot be determined in a laboratory. This is because the froth is scraped during a laboratory flotation test and thus does not exhibit natural behaviour, and it is not possible to scale-up froth transport distance or air rate. These values are generally compared via calculation to rule-of-thumb maximum values to establish if these values will be exceeded by the flotation cell selection.This paper first reviews these critical froth transport parameters and then discusses actual parameter values across diverse operating sites, with varying cell duties, cell sizes and types, orebodies and particle sizes. These values are compared against the industry rule-of-thumb to test the applicability of the rule-of-thumb to actual performance. Options are also presented for adjusting these parameters in operating flotation cells.CITATION:Coleman, R G and Wong, B, 2018. Flotation launder design and the measurement of critical froth transport parameters, in Proceedings 14th AusIMM Mill Operators&#39; Conference 2018, pp 353–362 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

When studying minerals degrees at university, all the emphasis is towards sending the graduates into the bush to work at a remote mine; however, that is not the only option available to new graduates. There are positions in equipment supply companies, commercial laboratories, research organisations, engineering companies and contractors of many types. The aim of this paper is to show metallurgy graduates that there are non-mine site based career options available to them that offer outstanding career development. This is illustrated by outlining the research being undertaken by Magotteaux Australia and by telling the story of a graduate metallurgist working in MagotteauxÆs small research group. Magotteaux is an international supplier of grinding media and wear resistant components for the mining industry. The Australian research group is focused on determining the effects that the choice of grinding media has on subsequent processing, for example flotation and leaching, by using newly developed tools and techniques.

Jan 1, 2006