Search Documents

By E J. Coyle, L A. Millington

Tailings storage facilities are geotechnically complicated structures that develop heterogeneous strength profiles and varied porewater conditions. The monitoring of porewater pressures is one of the only direct measurements that can be performed to monitor the performance of a facility throughout its life and is of particular importance in upstream facilities. Foundation underdrainage, continuous and staged tailings deposition, climate inputs (rain, snow, humidity, evaporation, etc), and stratified tailings permeabilities can complicate this critical measurement that introduces uncertainty to stability analyses. These difficult conditions manifest in vibrating wire piezometer measurements as very low or negative pressure readings, both of which are within the instrument’s range of accuracy. However, the data can be difficult to interpret, and a range of interpretations are adopted from optimistic low phreatic surfaces to conservative fully saturated tailings. Where tailings are potentially liquefiable, these very low readings introduce further uncertainty regarding the pore space saturation ratio and liquefaction potential above the estimated phreatic surface. This area of uncertainty is the vadose zone, and its affect on tailings behaviour is not well understood. The two facilities analysed in this paper are upstream, raised embankments with tailings classified as clayey, sandy silt that have been found to be potentially liquefiable. The vibrating wire piezometers (VWP) at both sites show very low or negative readings when they are initially installed near the surface and then go through cycles of re-saturation and de-saturation. Eventually the readings settle as the VWPs are buried deeper within the tailings. The instrumented sections within the tailings column do not show consistent readings that would be indicative of a hydrostatic phreatic surface at either site. Rather, they are highly variable and can be interpreted as either representing a high phreatic surface within the tailings or as a ‘perched’ phreatic zone within the tailings layers. How the VWP data is interpreted has a significant impact on how the facilities are raised and operated. The design outcome for Site 1, which adopts a lower phreatic surface, results in an embankment that meets factor of safety (FoS) requirements under residual strength conditions without any buttressing. Conversely, a conservative (high) phreatic surface has been adopted for Site 2 and has resulted in the facility requiring a significant buttress to meet FoS under residual strength conditions.

Jul 1, 2021

By V Lawson

Vale’s Sudbury Clarabelle Mill processes Cu/Ni ores from a number of mines in the Sudbury basin in Ontario, Canada. Bulk sulphide flotation produces a copper-nickel concentrate with pyrrhotite as the major diluent. After successful commissioning of the Voisey’s Bay Cu/Ni Mill (VBN) in Labrador, a miniplant campaign on Clarabelle ore with the VBN flow sheet produced a significant recovery improvement over current performance. In 2001, the Mill Redesign Project moved grinding energy into rock/sulphide and pentlandite/pyrrhotite separation and in 2006 Cu/Ni separation was re-introduced to Clarabelle Mill to produce a saleable Cu concentrate. The projects were a great success. What remained was to simplify the Clarabelle flow sheet by introducing the missing components found in the VBN flow sheet. This project known as CORe has evolved through many stages including the mining boom and surviving the 2008 economic downturn and it is scheduled for completion in mid 2013. This paper outlines some of the challenges faced in this major brownfields project – organizational, technical, financial and operational.

Aug 8, 2011

By M Edhammer

In 2007, Atlas Copco introduced an integrated tunnel scanner/profiler. The tunnel scanner, which is integrated into the control system, is mounted on the drill rigs, and replaces the previous variants of non-integrated scanner equipment. The Atlas Copco Tunnel Profiler, which is the name of this system, is currently being used by several contractors and mines on various projects in Scandinavia, Finland and Australia. Atlas Copco Tunnel Profiler can scan a tunnel of 65 m2 in just five minutes and is integrated with the computerised control system for the drill rig. This integration means that the results of scanning are immediately available for analysis on the computer screen both in the drill rig and in Tunnel Manager; a software for tunnel and drift planning.In 2008, a method was introduced for locating the drill rig with a total station navigation (TSN) system, integrated into the control system. TSN systems are used by a number of contractors in Scandinavia and Finland, as well as elsewhere in the world. Using a TSN for navigation is in itself not new, but when this is integrated with the control system it provides the opportunity for individual drill rig operators to use this method, without the direct assistance of a surveyor. TSN gives a very precise indication of the drill rig’s position in relation to the tunnel design. An accuracy of ±1 cm compared with the ±10 cm which is normally obtained with the traditional method using tunnel laser and sight plates on the drill rig’s feeder. The closer a tunnel is blasted to its planned profile, potentially the more is saved in terms of less shotcreting, extra rock bolting and other corrective work. A better quality tunnel is the key to better overall economy and today’s technology makes it possible to achieve that goal in every type of tunnelling and mining project.In addition to total station’s ­navigation and Tunnel Profiler, the concept of ‘high precision tunnelling’ also includes:•Software tunnel planning: Tunnel Manager, Tunnel Manager Pro and Tunnel Manager Measure while drilling.•Measurement While Drilling (MWD)collects the various drilling data and the interpretation of these for the early identification of variations in the rock.•Rig Remote Access (RRA) is a support for wireless or wired communication between drill rig and planning office. The result is being able to send planning data to the drill rig and to simultaneously have the facility for logged files to be sent from the rig to the office. There is an option of an external computer logging in to the drill rig’s control system to view menu screens and settings, and remotely troubleshoot and plan appropriate action.

Mar 21, 2011

The Pasminco mine at Rosebery in north western Tasmania is a medium sized underground base and precious metals mine. In April 1992 a major wedge failure of approximately 5000 t occurred in the backs of a main access drive to the 18 level H Lens orebody. This collapse prevented access to 190 000 t of ore which had been scheduled for production in July - August 1992. At the time of the collapse, the mine was in a transition period between mining small pillar remnants of several other orebodies and developing to the new deeper J Lens orebody.The development at this orebody was behind schedule and it was necessary to find a cost-effective and timely alternative to a 75 m bypass drive around the fall area.A Lysaght- Fletcher multiplate steel arch was available on-site from a deferred surface road project and it was decided to use this arch to regain access through the fall area. Due to the danger of continued minor falls, the entire 18 m long, 3.95 m high x 4.5 m wide tunnel had to be assembled in the 4.7 m wide x 5 m high accesss drive and pushed into the fall area as a single unit.

Jan 1, 1993

By M Hawkins

The Clem Jones Tunnel (formally known as the North-South Bypass Tunnel), a A$2.88 billion road tunnel project in Brisbane, Queensland, was successfully completed almost seven months ahead of schedule. The project included two parallel 4.7 km long road tunnels, 740 m of intermediate roadway access ramps and two auxiliary ventilation tunnels. The tunnels incorporate intelligent tunnel systems, best practice fire and life safety standards and typical civil tunnel elements.Over the duration of the project the Parsons Brinckerhoff (PB) and AECOM (formally Maunsell) design joint venture (MPB) were Lead Designers to the Leighton Contractors and Baulderstone Bilfinger Berger Joint Venture (LBBJV). Construction of the toll road commenced in September 2006 and was completed in March 2010, with the tunnel opening then. Contributing to the success of this project was the continued support the lead designers gave throughout the construction period.This paper will focus on some of the structural elements that contributed to the success of the project – in particular the cable tunnel structure, a small precast, culvert shaped element under the pavement of the mainline tunnel, and the fit-out of the Gibbon Street shaft which were designed to be constructed in a combination of precast and in situ concrete.The cable tunnel was incorporated early in the design phase and runs the length of much of the tunnel. This paper will outline the challenges faced by the designers with implementing this system which provided significant construction advantages, among which were being able to install a separate ventilation duct during construction and to start fitting out the mechanical and electrical conduits and drainage system while tunnelling was still underway.The Gibbon Street shaft had a length and width of 20 m by 40 m and an overall depth of 38 m. A 20 m high structure of precast and in situ concrete was constructed in the base to accommodate mechanical and electrical equipment and provide a take-off access for the southern ventilation tunnel. The construction purpose for this structure was to provide a junction between the tunnel boring machine (TBM) and the roadheader-style tunnels, a staging platform for commencing the roadheader tunnelling, and a platform where the TBMs could be dismantled and removed.The design was assessed and reviewed many times throughout the construction process to address the needs of each of these stages. Innovative use of precast concrete was used to minimise construction time.Additionally, the designers provided support to the construction team from the time of design completion through to the tunnel opening. This meant that the changes to the design and adjustment of construction loadings could also be assessed. The fi nal outcome resulted in an efficient construction sequence and a project that has provided an excellent outcome for the client, stakeholders and community.

Mar 8, 2011

Kumba Iron OreÆs Sishen Mine is one of the worldÆs largest iron ore mining operations situated in the Northern Cape, South Africa. It produces 29 million tonnes of iron ore products per annum using a dense medium separation (DMS) beneficiation process. Kumba is currently commissioning the Sishen Expansion Project (SEP) which will produce a further 13 Mtpa product through a jigging beneficiation process. The products from the Sishen Mine are highly sought after and consumed by domestic and various European and Asian customers. During beneficiation iron ore slimes are generated and discarded as waste material to the slimes dams. A study was initiated in 2005 to investigate processes to beneficiate these slimes to saleable products û prompted by the current high demand for iron ore products and the high grade in the Sishen slimes thickener underflow of approximately 54 per cent Fe. Initial laboratory scale test work indicated that a 66.5 per cent Fe iron ore concentrate could be produced from the Sishen slimes thickener underflow through a process of classification, two stage wet high intensity magnetic separation (WHIMS) and five stage flotation. This process, however, did not produce the desired results during pilot plant testing and numerous alternative process routes were investigated. The process that did achieve the desired product grade of 66.5 per cent Fe at economically feasible product yields consisted of two stage WHIMS using SLON magnetic separators. Results achieved indicate that the thickener underflow slimes can be upgraded from 54 per cent Fe to 66.5 per cent Fe at a product yield of ca. 40 per cent. Product yield could be increased through the further beneficiation of the SLON tails. The Sishen slimes thickener underflow production rate is ca. 3 Mtpa û resulting in a potential concentrate production of ca. 1.2 Mtpa. The slimes concentrate will be fed to a pelletising plant that will produce 66 per cent Fe pellets destined for domestic and or export markets.

Jan 1, 2008

By M Fritz, B Ziegelaar

"For moisture samples, the International Standard for iron ore sampling states the following: Moisture samples shall be processed as soon as possible and test portions weighed immediately. If this is not possible, samples shall be stored in non-absorbent airtight containers with a minimum of free air space to minimise any change in moisture content, but should be prepared without delay. ISO 3082 (2009)Prescribing what to do is of course easy. Putting it in practice is, however, a little more problematic.The iron ore industry has seen quite some changes in the last ten to 15 years, such as: a large increase in the volume of seaborne trade new ore types and blends coming onto the market new mines, processing plants and port facilities producing more and loading faster an increase in wet processed ore products a dramatic rise and then equally dramatic fall in the iron ore price followed by a recent recovery.All of the above have had an effect on sampling facilities. The large increase in volume coupled with ambitions such as labour efficiency, safer operations and higher precision has driven the installation and retrofitting of automated sampling and robotic sampling preparation plants in order to keep up with increased quality control.Designers of sampling facilities are invariably instructed to build plants that comply with ISO 3082. In general this means that the plants are compliant in respect of the number of primary increments, gross sample masses and sample division rules. The clause at the beginning of this abstract is mostly overlooked as it only appears in a section (4.1) describing the basic requirements of a sampling system.An error of 0.1 per cent in moisture changes the value of 1 Mt of iron ore at US$50/t by US$50 000. At 700 Mt/a of Australian iron ore exports, this is US$35 M. Frequently, errors from 0.5 to 1 per cent in moisture measurements are encountered.In comparison an error of 0.1 per cent Fe is US$0.081 (US$50/t and 62 per cent Fe base) per tonne, that is US$81 000 per Mt or about US$51 M for the same Australian annual iron ore exports.It is somewhat mystifying that we in the ISO Technical committees spend extraordinary energy (= money and time) on improving measurement techniques, whilst the big costs are in sampling errors. This is particularly true for moisture measurement. Our paper quantifies some of the sources of moisture measurements errors and suggests mitigating actions.CITATION:Ziegelaar, B and Fritz, M, 2017. Sampling for the percentage moisture in the iron ore industry, in Proceedings Eighth World Conference on Sampling and Blending, pp 271–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

May 9, 2017

By C Jacobsen, N Harries

Assessing and managing instability hazards is an essential activity when working with unstable natural slopes and excavated open pit mining slopes. Slope monitoring has become the standard technique for the management of geotechnical risks associated with mine slope instability hazards. In recent decades, a proliferation of new monitoring techniques such as terrestrial radar, satellite InSAR and LIDAR have become standard operational tools, complementing conventional survey-based monitoring solutions. A reliable monitoring system should identify and record incipient anomalous slope movement. Although the most obvious purpose of a monitoring system is safety related, slope deformation and performance monitoring also enhance the understanding of slope behaviour and assists in improving system design and implementation. For a monitoring system to be considered an effective early warning tool, it needs to operate in real-time and should be linked to the mine’s emergency communication systems. Terrestrial radar systems have been developed that can provide near real-time measurements, at a high level of precision and covering broad areas in all weather conditions. This has had a positive impact on the management of geotechnical risks in operational conditions. The technology adoption of RADAR in mine monitoring has significantly progressed in the last 20 years from technology enthusiasts, to visionaries, to pragmatists to conservative users. However, the increasing adoption of RADAR cannot reduce or remove other monitoring techniques that often have important benefits; even if these technologies cannot be used as a real-time operational tool. An increasing awareness on the importance of combining data from different monitoring techniques to develop a holistic picture of all possible geotechnical hazards is a current industry trend. This is proving to be an excellent foundation for managing hazards associated with slope instability in open pit mines, and is only expected to improve with time with the adoption of new technologies based on big data and Artificial Intelligence (AI).

Nov 29, 2022

Production sharing and cost apportionment in joint ventures is commonplace in Australasia today and elsewhere. It is a recognised convention that, with the exception of a free carry situation, joint venture participants usually share the proceeds of the joint venture in direct proportion to their respective participating interest, after having first paid its respective cash calls, in advance, to cover the projectÆs ongoing operating and capital cost requirements.In surface mines, the parties simply pay their way and take their proceeds in this manner. In underground mines, the situation is no different, though treatment of capital, depreciation and tax may differ between the parties. A common feature in many cases is the creation of a joint venture entity to conduct the business. This entity then collects cash from the parties, banks it, employs the staff, runs the operation, provides reports and pays out the proceeds. This convention appears to be relatively simple in application. In practice, it has been known to be complicated in the situation where the participants take their product at the mine gate and undertake their own marketing and selling arrangements. A more complex situation presents itself where the joint venture tenement boundary with an unrelated third party straddles an economic deposit. In this scenario, both the joint venture parties and the third party may wish to mine the deposit, sharing some infrastructure and costs, yet taking their own product as it is produced. A case study outlining such a situation is presented in the paper, outlining firstly how the major cost categories were identified and treated for cost apportionment purposes. Secondly, a mechanism for the equitable apportionment of product is suggested. Finally, issues such as timing and cost reporting are dealt with, together with a checklist of points which should be considered when a similar situation might arise in the future.

Jan 1, 2002

The N3500 orebody is the northern continuation of the 3500 orebody at Xstrata Copper's Enterprise Mine and occurs at a depth of 1.3 to 1.8 km. At the nearby S3500 orebody, extreme deformation was observed in access drives where there was a high number of bedding planes per metre combined with either graphite or talc infill. The observed failure mechanism was largely controlled by the geometry of the inclined bedding submitted to high horizontal stresses. Due to the anisotropic strength and deformation behaviour of the shale rock mass, traditional isotropic methods of geomechanical property estimation based upon GSI are not appropriate. A numerical modelling approach, based upon the distinct element codes UDEC (2D) and 3DEC (3D), has been developed to accurately simulate the failure mechanisms and deformation observed in the initial infrastructure surrounding the N3500 orebody.

Nov 25, 2010

Development of a small ore body to 137m below surface was carried out in sixteen months driving 610m of 1:5 decline.

Jan 1, 1973

By A G. L Pratt

Inclined troughed belt conveyors are more frequently being selected from a range of alternatives, which include shafts and trucks for ore haulage in underground mass mining projects. Belt conveyor haulage systems are being operated with lifts exceeding those normally associated with truck haulage systems and approaching the limits of shaft haulage systems. A belt conveyor haulage system, in this context, incorporates subsystems for: crushing,tramp detection and removal, andhaulage. This paper presents details of recent inclined troughed belt conveyor systems for underground mining operations, and explores the application of inclined troughed belt conveyors for the increasing demands of future underground mass mining projects.

Jan 1, 2008

By G S. Beros

In 2019 the Chinese Ministry of Ecology and Environment issued guidelines promoting the implementation of ultra-low emissions in the iron and steelmaking industry. These guidelines aim to drive improvements in air quality through the reduction of particulate matter (PM), sulfur dioxide (SO2) and nitrogen oxide (NOx). Secondly, it also represents an initial means to commence decarbonisation of the industry. The ultra-low emissions guidelines propose that well over 80 per cent of China’s production capacity will achieve these targets by 2025. In response, many sintering operations have implemented numerous improvements to the process that result in significant efficiency gains. Of note is the adoption of deep bed sintering where, with some modifications to equipment, the sintering bed depth is increased resulting in sizable reductions of SO2 and NOx emissions. This paper will also provide an overview of the requirements to introduce deep-bed sintering into an operation and highlight test work completed which quantifies the resultant reduction in emissions.

Nov 8, 2021

By M Dalm

More and more mining companies are becoming aware of the potential benefits of sensor-based ore sorting and process optimisation. This is reflected by a growing number of analysers that are available for drill hole logging, conveyor belt scanning, ore sorting, slurry analysis, etc. These tools all rely on a specific sensor technology that can be used to detect a material property such as colour, density, mineralogy, or chemical elements. However, all sensors have restrictions on the minerals and/or elements that can be detected or inferred. This is caused by the physical mechanisms behind the technology and depends on mineral concentration and compositional heterogeneity of the ore. Since nearly every ore deposit is unique in composition and characterised by different geological features that drive heterogeneity, no one-size-fits-all sensor solution is available. This makes it difficult for mining professionals to find suitable sensing technologies that can help them solve problems and improve processes for their specific ore types.

Sep 1, 2024

By E Acu±a, B Prosser, R Alvarez, K Wallace

This paper describes the ventilation analyses performed for the access tunnels at the New Level Mine project (NLMP) at CodelcoÆs El Teniente operation outside of Rancagua, Chile. This new mine is anticipated to reach a final production of between 137 and 180 kt/d. Production from the NLMP is scheduled to start in the year 2017. The main access tunnels (MAT) are approximately 9 km in length, with one for personnel and supply access and the second one for ore extraction through a conveyor system. These two tunnels are a critical component of the initial stage 1 development and will be constructed independently of the existing mine workings. The tunnels were originally designed to be constructed with two tunnel boring machines. However, later analyses changed the construction approach to a conventional drill and blast technique. Because the design included two mid-tunnel ramp-to-surface connections, conventional mining methods would allow for development of the tunnels with multiple working faces to achieve a more rapid schedule. This paper presents the initial baseline considered for the ventilation design and the optimisation methodology applied by Codelco to minimise the airflow and pressure requirements of the ventilation system. Modifications to the design resulted in the addition of strategic airways and raises that could provide a saving of approximately 1 MW, when compared to the original design.CITATION:Acu±a, E, Alvarez, R, Wallace, K and Prosser, B, 2013. Ventilation considerations for the new level mine project access tunnels, in Proceedings The Australian Mine Ventilation Conference , pp 203-206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By G Britton, P Moynagh

As more than a few mines gradually sink under the weight of emails, whiteboards, notice boards and ever more complex spreadsheets, the holy grail of effective short-term interval planning and control in underground mines is as far away as ever. Despite the mining industry investing ever greater amounts in planning and Enterprise Resource Planning systems, short-term plans become ever more complex and rigid. What the industry desperately needs are not more ‘disembodied voices down the speaking tubes’, but flexible and effective planning systems that encourage people to make reasonable commitments to each other so that everyone can work as a coordinated team to complete the work required each shift.One solution to the challenge has emerged. This paper describes the ‘Fewzion’ shift planning and short interval control system which has been developed at Anglo American’s Moranbah North and Glencore’s Oaky Creek coalmines in Central Queensland. Fewzion has drawn on management theory embodied in Management Operating Systems, Lean and Theory of Constraints approaches to continuous improvement to play a key role in both mines achieving record breaking tonnages.In addition to explaining the Fewzion approach, a case study is presented describing how Anglo American’s Moranbah North improved production by 39 per cent in 2014/2015 and won ‘Coalmine of the Year’ two out of the last four years and how Glencore’s Oaky Creek sustainably improved monthly development meters by 34 per cent within two months of implementing Fewzion.CITATION:Moynagh, P and Britton, G, 2017. How a frontline planning and commitment system improves trust, commitment and results in operations, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 235–240 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By K George

The Dugald River lead-zinc-silver deposit is located approximately 60 km north-west of Cloncurry and 87 km north-east of Mount Isa. The development project is expected to turn operational in 2018. The resource is estimated to contain 61.1 Mt at 12.6 per cent zinc, 1.9 per cent lead and 34 g/t silver, with a projected mine life of 25 years. The evolution from exploration project to development project has presented multiple challenges for the technical team. Understanding and modelling the structural complexity of the deposit has been one of these challenges.Historically fault zones were logged as a lithology, with structural measurements recorded in a separate database table. When underground drill programs and development commenced in late 2012, it was recognised the deposit was more structurally complex than had been modelled. The extensive number of fault zone lithologies in core logging, made it difficult to identify fault trends and model faults in 3D software packages.In 2014, a structural project was conducted to produce a fault model for the deposit. The project highlighted that by logging the faults as a lithology, a shortage of fault characteristics was being recorded. Additionally, structural information could not be filtered to identify different fault sets due to the lack of information available to filter on. One of the major outcomes of the study was to change the methodology for the structural logging of drill core.Faults are now logged in a separate structural log. The structural log collects two types of information: interval data and point data. The interval data represents the damage zone of the fault in the surrounding rock and the point data the plane of movement for the fault. The faults are further characterised by their intensity on a scale of one to five, the type of fault structure (fault breccia, fault vein etc), the minerals present on the fault surface and structural measurements when available.The new data set allows fault data to be filtered based on fault characteristics, making implicit and explicit modelling of the faults more timely and accurate. The data set can be used to produce fault wireframes as single surfaces from the point data or hanging wall and footwall surfaces from the interval data. The logging method and how its applied in fault modelling form the focus of this paper.CITATION:George, K, 2017. A new approach to logging and modelling faults at the Dugald River Pb-Zn-Ag deposit, North West Queensland, in Proceedings Tenth International Mining Geology Conference 2017, pp 315–320 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By P Knights

This paper examines the process and specialised skills required to extract insight from data routinely collected by mine operations, maintenance, engineering and environmental departments. Typical insights include: enhanced understanding of root causes; recommendations for next best actions; and simulation of likely scenarios. The skills required for advanced analytics are not currently the domain of mining engineers. The professions required by tomorrow’s mines are likely to be diverse and multi-disciplinary, and will include control engineers, software engineers, mathematicians and statisticians. A case study is presented that correlates mobile equipment production delays with rainfall events across three mines on the east coast of Australia. One mine is shown to have significantly more rain related downtime than the other mines, providing compelling evidence to improve productive performance.

Nov 22, 2011

The Australian industrial relations system is in a state of constant change. We are undergoing a transformation from a compulsory arbitration and an award based system to one which is fundamentally rooted in the concepts of enterprise bargaining. This is true both at the State and Federal level. The structural changes which facilitate the movement away from the predominance of Awards to enterprise agreements has been fostered by both sides of the political spectrum and is a cornerstone of their respective industrial relations platforms.In determining what form or combination of forms of industrial instrument(s) should apply to the individual enterprise, employers must have regard to the viability and sustainability of each form in the changing industrial climate. In particular employers should have regard to the needs and agendas of their employees and unions which may purport to represent Them.

Jan 1, 1998

By D J. Robinson, L L. Kuhar

In-situ recovery (ISR) is accepted and applied across many geographies, and approximately 50% of the world’s uranium is currently extracted by using an ISR method (World Nuclear Association, 2014). The low environmental impact, the elimination of risk for mine workers and the fact that all of the lowest-cost producers of uranium use an ISR approach should raise interest from traditional miners (IAEA, 2014). However, the broader application of ISR to other commodities and mineral systems remains limited. A number of demonstration (experimental) copper projects have been undertaken (Sinclair and Thompson, 2015) with a few copper projects in Arizona being close to demonstration (Florence, 2018 and Gunnison, 2018). Evidence of very few economically operating ISR copper projects can be found (for example, the Russian, Uralgidromed OAO, built by the Russian Copper Company in 2005 and operated as an ISR facility from the Gumeshevskoye deposit (Russia Mining, 2018). A number of gold deposits, particularly paleochannel deposits, have also been considered for ISR, but, to the best of our knowledge, only limited demonstration and no commercial operations have been established, yet (Kuhar et al, 2018 and references therein).CITATION:Robinson, D J and Kuhar, L L, 2018. Extending mine life through application of an in situ recovery approach, in Proceedings Life-of-Mine 2018, pp 56–57 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018