Search Documents

The accuracy with which block estimates are perceived is obtained by calculation of the kriging variance. This is dependent upon the model chosen for the semi-variogram of the deposit. For an extensive series of spherical semi-variograms the changes in the kriging variance resulting from various degrees of misassignment of the relative nugget effect are investigated. The results are reported as contour maps of percentage change in kriging variance as a function of the range and relative nugget effect of the true model.

Jan 1, 1985

By P Holtham, K Duffy, L Pyle, W Valery

The mining industry is becoming increasingly focused on pre-concentration due to its potential economic and environmental benefits, particularly for the more complex, low-grade, high throughput operations now being developed. Advances in technology have seen bulk ore sorting (BOS) trialled at several operations. However, BOS should not be seen as a ‘silver bullet’, it can offer significant benefits, but only under the right conditions. Deposits with interspersed mineralogy or disseminated, fine-grained minerals can be difficult for BOS. Large batches of barren or low-grade material are required for BOS to be effective. Hatch has recently completed several studies for clients who believed that bulk sorting was the most suitable pre-concentration technique for their operation, based only on an assumed sorter recovery or on laboratory trials of the chosen sensor. However, minimal consideration had been given to the heterogeneity of the deposit, the achievable separation batch size or sensor repeatability. Evaluation of BOS needs to consider both heterogeneity and sensor suitability. The valuable or gangue mineral must be present in such a way that it can be separated effectively in the large bulk sorting batch sizes, without competing minerals or changing ore characteristics affecting the metal upgrade or recovery. Also, the sensor chosen must be able to detect either the valuable mineral, a proxy for the valuable mineral, or a gangue mineral for rejection with sufficient accuracy and precision (repeatability). This paper presents three recent case studies, emphasizing markers which indicated that bulk sorting was unsuitable for the project whilst highlighting the pre-concentration technologies which were applicable (including particle sorting, and coarse particle gravity separation). The modelling methodology, equipment sizing and forward work plans developed to verify these alternative solutions are also presented, demonstrating the key factors contributing to a thorough scoping assessment.

Aug 24, 2022

By C Jenkins, J Jasper, Y Suryaputradinata, S Lozyk, M J. Hartmann

The primary objective of mining companies is to function as a profitable business by delivering products that fit customer requirements in a safe and sustainable manner. Optimum resource utilisation is a critical focus area to achieve this objective, and the long-term sustainable business performance of a mining company is determined by the extent to which this is achieved. Technology improvements and/or new technology development could improve resource utilisation. However, adding new projects to a Brownfield operation carries risk. Overall project schedules, tie-in schedules and safety risks normally receive adequate attention, but the introduction and integration of new technology to a Brownfield site also carries the significant risk of failure to achieve design performance (quality or throughput). This risk must be addressed via rigorous design phase risk assessments and piloting. Post commissioning, the effective metallurgical integration of any new technology/circuit/process plant into an existing process plant calls for critical assessment, through circuit performance testing, and optimisation to ensure alignment with design criteria. In addition, this approach provides clear focus areas for further optimisation of the new plant and additional opportunity for overall plant optimisation. Roy Hill recently navigated this process successfully, and this paper provides feedback on the journey that led to improved resource utilisation.

Nov 8, 2021

By H Fletcher

Iron Ore Holdings Ltd (IOH) is an emerging junior iron ore company that is actively developing projects in the Central and Western Pilbara region of Western Australia. IOH commissioned URS Australia Pty Ltd (URS) in mid-2008 to prepare environmental assessment documents for the Phil’s Creek Project, which was rapidly moving into the development phase. This project comprised a small open cut iron ore mine that was expected to deliver approximately seven million tonnes over a five year mine life.IOH faced several challenges in the environmental assessment process for the Phil’s Creek Project. Although the Phil’s Creek Project attained approval but has now been placed on hold, it is a useful case study to discuss these challenges and how IOH addressed them. Several important lessons were learned through this process that can assist other proponents in addressing environmental challenges in a constructive and proactive manner.One major challenge faced by IOH related to the endangered northern quoll (Dasyurus hallucatus). Another challenge was the unusually high species richness of troglofauna recorded within the project area, with several species initially known only from within the proposed pit footprint.Meeting and overcoming these challenges has provided IOH with an increased understanding of the level of input required for consultation with government departments regarding environmental assessments, and this should stand the company in good stead for developing future tenements. Challenges in regards to the environmental assessment process may be faced during future developments, but IOH’s experiences to date and the lessons learned from the Phil’s Creek Project, will help pave the way for successfully overcoming them.

Jul 11, 2011

By M L. Muller, A R. O’Donnell

The Mount Isa Mines (MIM) Copper Concentrator has an extensive history of reagent trials, with different reagents coming in and out of favour over the years. The research and use of carbon depressants is particularly prevalent, as carbonaceous pyrite is a major source of concentrate dilution. Years of research led to the use of naphthalene sulphonate due to its excellent carbon depression properties. However, due to rising reagent costs carbon depression ceased in the late 1990s. This led to the loss of knowledge about the use and value of naphthalene sulphonate. Cyanide is used at the Copper Concentrator for the sole purpose of pyrite depression and over the years multiple projects have been devoted to finding alternatives to it. In 2012 the neighbouring MIM Lead-Zinc Concentrator replaced cyanide with naphthalene sulphonate which resulted in cost savings and the elimination of a hazardous reagent. In 2013, plant trials were conducted at the Copper Concentrator in hopes to replicate the outcomes obtained at the Lead-Zinc Concentrator. The results of the trials conducted at the Copper Concentrator showed that naphthalene sulphonate could not replace cyanide and this work was set aside to pursue more promising projects. Further research conducted in 2014 found that mineralogy and a better understanding of the depressing mechanism of naphthalene sulphonate held the key to improved pyrite depression at the Copper Concentrator. The findings showed that Mount Isa copper ore contains two forms of pyrite; euhedral pyrite (cubic pyrite) and framboidal pyrite (carbon rimmed spheres of pyrite), both of which require different reagents to sufficiently depress them. Naphthalene sulphonate was found to be an excellent carbon depressant, suitable for depressing graphite and framboidal pyrite, whilst cyanide specifically targets euhedral pyrite.In 2015 laboratory test work was conducted to examine the use of naphthalene sulphonate in conjunction with cyanide to selectively target both forms of pyrite. This work led to a full plant trial, the results of which showed a significant increase in plant performance, with higher copper concentrate grades and recoveries being achieved. This paper aims to focus on the benefits and importance of understanding past work and linking a detailed knowledge of feed mineralogy to reagent selection for improved plant outcomes.CITATION:O’Donnell, A R and Muller, M L, 2018. Selectively targeting hydrophobic gangue minerals at the Mount Isa Mines Copper Concentrator, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 413–421 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By J Garritsen, P F. Wells, M Xu

IncoÆs Clarabelle mill currently processes ores from eight mines in the Sudbury basin area in Ontario, Canada. The ore from the Garson mine contains a much higher concentration of arsenic than the other ores. Adding this ore into the feed to the mill has resulted in an increase in arsenic content of the Cu-Ni bulk concentrate to a level that significantly affects the smelter operation, and more importantly the efficiency of Cu-Ni separation in the Matte separation plant. The arsenic occurs mainly as gersdorffite (NiAsS), with a small amount being in the form of cobaltite (CoAsS). Extensive laboratory tests on depressing arsenic in Garson ore flotation have been conducted and two reagent suites have been identified as effective arsenic depressants. One is the so called MAA depressant which is a mixture of magnesium chloride, ammonium chloride, and ammonium hydroxide. This reagent combination was reported to depress other arsenide minerals such as arsenopyrite (FeAsS) and enargite (Cu3AsS4). However, in this study for the first time it has been shown to have a depressing effect on gersdorffite. The other reagent suite, a mixture of triethylenetetramine (TETA) and sodium sulfite, that has been reported as an effective pyrrhotite (Fe1-xS) depressant in pentlandite ((NiFe)9S8) flotation, has not been reported as gersdorffite depressant before. The effectiveness of both reagent suites is more pronounced when the arsenic minerals are oxidised through pulp aeration or the addition of hydrogen peroxide. With a flow sheet consisting of a magnetic separation, rougher- scavenger flotation, followed by regrinding and cleaning of combined magnetic and scavenger concentrate, the arsenic recovery to the final Cu-Ni bulk concentrate was reduced from 73 per cent in baseline test to less than 30 per cent with either reagent suite at no decrease in nickel recovery. The TETA/sulfite reagent combination has the advantage over the MAA suite in that pyrrhotite is also depressed, rather than being activated, and the copper and nickel concentrate grades are therefore increased.

Jan 1, 2005

By Scott A

This paper summarises some of the results of the ACARP-JKMRC project 'Optimisation of Dozer Operations in Open Cut Mines'. The work has involved an industry review, design and conduct of field trials of coal seam preparation using dozers, nume

Jan 1, 1998

By M Recabarren, A Echeverria, J Ronda, J I. Guzman, R Dodds, G Juarez, E Vila-Echague

A strategic mine plan is a fundamental part of any mining operation. It must provide a realistic and operative extraction and processing schedule, and yield the highest value for the business. For open pit mines, the problem can be modelled as a set of blocks representing the deposit, for each of which we need to decide if it is going to be mined, if so, when and where it will be sent (process, stock or dump).This problem can be proven to be of NP-Hard complexity. The traditional approach used by mining engineers to tackle this complexity is to separate the problem into more tractable components, solving each separately. The first step is to use the Lerchs-Grossman (LG) algorithm to obtain the final pit limit, as well as a set of optimised pit shells (nested pits), using different input prices. Then, using this input, operational phases are designed. Third, the set of phases can be used as an input for a phase-bench style optimisation, usually using a mathematical programming-based algorithm.There are, however, several problems with this approach. First, dividing the problem into simpler parts has the consequence that any compromises made at early stages limit the potential value left for the following steps. Second, LG is a static algorithm, with no concept of the time-value of money, capacity limits, opportunity costs, etc. Phase design is essentially a manual step, for which nested pits provide insufficient information in practice, and therefore the quality of the result in terms of potential net present value (NPV) depends strongly on the experience and expertise of the designer. This means that key input data such as commodity prices, different processes capacities and mine movement limits, are considered only at scheduling, when there is little room for optimisation. This sequential approach limits the potential value in each step, where a simplified problem is addressed, instead of addressing the real, and more complex problem, which is dynamic and should be solved as a whole.We present in this paper an algorithm, and its commercial software implementation, that addresses the dynamic problem as a whole, simultaneously and automatically creating a high-value strategic mine plan that adheres to basic operational constraints, determining dynamic cut-off grades and delivering a set of phases which can serve as a much stronger guide than nested pits for the final design. We discuss some of the key elements of the algorithm and propose a new methodology for strategic mine planning, where phase design dynamically responds to mining strategy definition. Results using different mining and operational parameters on a fictitious copper deposit are used as a demonstrative example.CITATION:Juarez, G, Dodds, R, Echeverria, A, Guzman, J I, Recabarren, M, Ronda, J and Vila-Echague, E, 2014. Open pit strategic mine planning with automatic phase generation, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 147–154 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By M A. González, J A. Romero, D L. Fuentes, C J. Poblete, O Abdrashitova

"Robustness can be defined as the ability of a system to resist change without adapting its initial stable configuration. Robust design methodology, which is widely accepted in the manufacturing industry, allows the establishment of robustness and reliability metrics in scenario analysis.In the mining industry, a mine can be considered as a system with design parameters such as processing plant and mining capacities. Traditionally, a limited number of scenario iterations are performed in an attempt to determine optimal capacity values. An important strategic decision such as process plant capacity in particular is made during the very early stages of a mining study, often based on a low level of information. Lack of time and tools to run and analyse a larger number of possible scenarios for different design parameter combinations are usually the main reasons for not performing a full analysis. In addition, the uncertainty of other mining study input parameters creates more risk in decision-making.With advances in technology, it is now possible to automate the process of generating several thousands of scenarios in an affordable and timely manner. This allows performing the results analysis and assessing robustness and reliability criteria within a reasonable time frame. It is possible to generate a surface of results based on the net present value (NPV) for each scenario. This surface will reflect the efficiency level of the capture of the economic rent for each production scale. In addition, each scenario can be tested under diverse conditions of volatility of other external variables such as prices, costs or recoveries for example.This paper aims to establish a methodology that applies robustness criteria to determine the best scenario on several surfaces of value, which is then assessed with real data from a mining project. Obtained results demonstrate the advantages of using the proposed methodology in dealing with the above-mentioned multidimensional problems. It allows better decision-making on key design parameters and better control of the risks of a strategic mine plan.Citation:Poblete, C J, González, M A, Romero, J A, Fuentes, D L and Abdrashitova, O, 2016. Use of Robust Design Methodology for Production Scale Definition in Open Pit Mining, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 284–291 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By M P. Murphy, C M. D Barton

When developing a new underground mine, the geological interpretation that guides the mineral resource is crucial to the preparation of a reliable ore reserve. In preparing a robust geological model to underpin a resource estimate, practitioners must weigh the comparative risk of accepting a relatively wide-spaced drill hole pattern, versus a more close-spaced pattern that ensures a high local geological confidence for mine planning but may have an exponentially increased time and monetary cost. This paper details the authors’ investigations into the geological uncertainty of IGO’s Odysseus Deposit, which is approximately 645 km north-east of Perth, Western Australia. At Odysseus, the komatiitic nickel sulfide mineralisation is irregularly cross-cut by nickel-barren pegmatites that have intruded and offset its thick ultramafic orebodies. These pegmatites generate significant uncertainty in the precision of Odysseus’ resource volume and tonnage estimates, as well as the subsequent quantification of pegmatite mining dilution in its ore reserve. To quantify the geological uncertainty in the pegmatite interpretations, IGO’s mineral resource practitioners prepared several geological risk studies over the Odysseus North lode, which is the lode most affected by the pegmatites. These studies included categorical conditional simulation of the pegmatites, preparing implicit geological models with alternative algorithms, trialling a machine learning application to prepare a maximum likelihood geological model, and finally assessing the early results of the pre-production close-spaced drilling to these different models. To assess the precision of the different single-outcome models, the authors’ compared the estimated pegmatite content of each model to the range of possibilities modelled by categorical conditional simulation within the planned stopes at Odysseus North. An estimation confidence score for each modelling method was then prepared for each alternative single-outcome modelling method. From these studies IGO concluded that a close-spaced drill pattern is essential at Odysseus, supporting the view of the Competent Person in 2017 who proposed a 25 m drill spacing in areas affected by pegmatite which had been partially classified as Inferred.

May 24, 2023

By M, C A. RosiFre, R C. Figueiredo e Silva

Jaspilites and underlying basalt contacts of the Archaean volcano- sedimentary Grpo Parß Group, Carajßs, host giant iron mineralisation in the ~100-km long, E-W trending Carajßs fold. Preliminary, unpublished geochronological data point to a Palaeoproterozoic mineralisation event. Geochemically, jaspilites are typical volcanogenic banded iron formations. Basalts exhibit evidence of spilitic seawater interaction. Iron-associated hydrothermal alteration of mafic rocks was induced by fluid infiltration in amygdales, with development of chlorite- and hematite-dominated zones. In the case of jaspilites, iron mineralisation encompasses: partial replacement of jaspilitic microcrystalline hematite by blasts of martitic magnetite; jasper recrystallisation, producing fine-grained, hematite-free granoblastic quartz; martite recrystallisation, forming lobate¦subhedral hematite; pervasive porosity development by quartz-chert leaching; incipient cavity filling by microlamellar hematite; and advanced filling by coarser, euhedral and comb-textured, tabular- shaped hematite.Peak hydrothermal ore textures indicate typical epithermal-crust conditions, supported by preliminary fluid-inclusion calculations at 160 - 200¦C. Such temperatures and extreme fluid-to-rock ratios during alteration must have exceeded the ambient metamorphic conditions, with the infiltrating fluid relatively hot and capable of leaching SiO2. Therefore, mineralisation developed over exhumed, Archaean, brittly deformed rocks, with mineral associations representative of very low- to low-grade metamorphism. Considering that chlorite (¦talc) abounds in mafic rocks; hydrothermal albite is developed; dolomite fills veins and vugs; the typical rare-earth-element (REE) pattern of jaspilites is significantly modified in higher-grade hard hematite ores (higher LREE); pyrite, copper sulfide minerals and rare gold occur in association with carbonate-quartz-rich alteration zones, it is suggested that an alkaline, H2O-Fe-CO2 mineralising fluid dominated, also containing species like S¦Cu¦Au. Peak-mineralising conditions are likely to have resulted from a single, evolving fluid, via incipient- through advanced-stage alteration phases. The porous, high-grade soft hematite-type ore (SH), rich in microlamellar and anhedral hematite, must have derived from interaction with this relatively hot SiO2-leaching fluid, whereas the high-grade massive hard hematite-type ore (MH) developed due to closer fluid-rock temperature equilibrium conditions, attained by mineral reactions, with relative increase in the Fe/Σcations ratios allowing the precipitation of subhedral-tabular hematite that partially cements the soft-hematite ore. SH and MH hematite ore types must thus reflect intermediate and high fluid:rock ratios, respectively. Since the N5 deposit is to date understood to contain the largest amount of the MH ore, its units are interpreted as the loci of the highest fluid:rock ratios in the district. Preliminary mineralogical information regarding the S11 deposit of the Serra Sul (south range) implies higher-temperature conditions. The near-equant grain size and the granoblastic intergrain relationship, coupled with the presence of riebeckite, augitic pyroxene and garnet, suggest hornfels textures. The data collected, though still relatively sparse, permit the speculation that the immense driving force for the Carajßs world-class iron deposits was a relatively shallow, igneous-related hydrothermal system. If such a model is correct, then the Carajßs Palaeoproterozoic iron deposits could represent an end-member of the iron oxide-copper-gold hydrothermal system in the province.

Jan 1, 2005

By R Grobler, D Burger, L Alberts

The current climate in the mining industry is allowing mining companies to further broaden their views and investigate technologies to improve the safety, efficiency and cost-effectiveness of their operations. Furthermore, underground mine environments will become more demanding for mining equipment and personnel as orebodies become deeper in weaker ground conditions with more extreme environmental conditions. Loading and hauling can represent significant components of the production cycle of an underground mine and automation of these activities can offer considerable benefits. Sandvik has accumulated a long history and experience in loading and hauling automation in underground mining. Since the late 1980s Sandvik has actively participated in several major research and development automation programs leading to the commencement of the development of an integrated system for semiautomated loading in 1999. Development work was later conducted to expand the capabilities of the system for automated hauling during 2001 and the AutoMine« system became commercially available. The first delivery of the AutoMine« system was completed in August 2004 in South America, where the system continues to operate in a full-scale production environment and is being expanded as the production area enlarges. Further systems have been delivered and are operational in North America, Africa and Europe. This paper focuses on the AutoMine« system deployed in Block 4 at De Beers Finsch Mine in South Africa. An overview of the mine and the process used to acquire the system and the key drivers which led to the selection of an automated solution are described. An overview of the initial system installation, subsequent expansions and future plans are presented. This is followed by a summary of the implementation and operational experiences associated with automated underground operations. The paper concludes by summarising the benefits that have been realised.

Jan 1, 2008

By N Jamson, T K. Rohde

The Mine is an underground zinc (Zn), lead (Pb) and silver (Ag) operation in central New South Wales (NSW). Broadly speaking the Mine has two domains that require rehabilitation, the mine industrial area (MIA) and the tailings storage facility (TSF). The MIA has been used for the handling and processing of ore and contains elevated sulfate, sulfide and metals (Pb, Zn). The TSF receives the by-products of processing, that is, potentially acid forming (PAF) tailings which also contain elevate sulfate, sulfide and metals. Typically, the rehabilitation of a TSF involves two controls. Firstly, controlling the potential for PAF tailings to form acid rock drainage (ARD) by limiting interaction with oxygen. Secondly, once the tailings are unsaturated, limiting interaction with water (usually as rainfall) to reduce the potential for ARD to be transported to the receiving environment. These two controls are often employed in the form of a cover.In semi-arid environments there are many Australian examples of covers that have been built to limit interactions of mine by-products with oxygen and water. Typically, the covers contain one or more layers and are built from soil and rock which may include run-of-mine rock. The Mine however has limited supplies of stockpiled soil; and run-of-mine rock is not generated in large volumes because it is used as backfill underground. A cover design strategy was developed to cater for these limiting factors. The strategy identified soil, ore and rock accretion (the accretion) below the MIA could be a potential source of borrow material for the cover. The purpose of this paper is to describe the cover design process, the method and results of large (2 m tall) column trials that were used as a cost-effective way to trial three cover options and finally, the paper describes the water balance that was developed from the column trial results and subsequent modelling using SVFlux.CITATION:Rohde, T K and Jamson, N, 2018. Making use of potentially contaminating mine waste in cover design, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 285–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By R F. Cota, C Freeman, A Heberle

"The Lamego mine is an underground gold mine in the Iron Ore Quadrangle in Minas Gerais state, Brazil. The mine produces 48 to 50 koz per annum, as part of the larger Cuiabá-Lamego Complex. This combined unit is AngloGold Ashanti’s largest gold producer in the Americas, contributing with 310 to 320 koz per annum.The mine started production in 2009, utilising cut-and-fill mining methods.A mining method change was trialled in 2014, introducing open stope methods. The key benefits proposed from this change are considered to be: improved safety by eliminating re-entry mining methods reduced mining costs/increased productivity from utilising bulk-mining operations.The results from the trial were encouraging, and open stoping participation expanded beyond a trial.Production from open stope areas reached 180 000 t (40 per cent of total run-of-mine; ROM) in 2015. While the change in mining method resulted in higher production rates, it also introduced a critical issue in terms of stope recovery rate.Average underbreak (unplanned loss of ore) in the larger open stopes reached 21 per cent in 2015. To manage this ore loss, a project targeting higher recovery was structured with three primary components: analyse current performance to define contributing factors (design process gaps, operating practices) investigate corrective actions apply corrective actions and maximise team engagement to ensure changes become standard practice.Within six months of commencement, a range of contributing factors had been identified, and the majority of the associated corrective actions implemented, including increased team engagement to ensure changes were not ‘once off’ actions.The outcomes show a clear reduction in underbreak (average ~12 per cent for 2016), with further improvement opportunities identified. The challenging target is now to achieve a further reduction to 10 per cent underbreak as the average for 2017. The results contributed 1400 oz and additional US$ 0.5 million to the cash generation profile for 2016.CITATION:Heberle, A, Freeman, C and Cota, R F, 2017. Increasing stope recovery in an underground gold mine by using effective analysis, corrective action and employee engagement processes, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 117–122 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 16, 2017

By J N. Farrell

Metallurgists frequently use a small number of large samples to characterise expected mill performance, with the a priori assumption that these few samples are representative of the entire deposit. Geometallurgical sampling is becoming more prevalent as a way to use many smaller samples to indicate the expected recovery as part of the Mineral Resource or Ore Reserve estimation.The evaluation of magnetite deposits involves specialised approaches to sample preparation, sample analysis and resource estimation. The sampling protocol for magnetite deposits will typically include the use of Davis Tube analysis. The Davis Tube is a mini-pilot plant that is used for determining the mass magnetic recovery from a small amount of sample ground to a specific size. The magnetic concentrate may then be analysed and together with the mass magnetic recovery, may be used to simulate the expected mill recovery. The magnetite sampling protocol is specific to each deposit, and is typically designed around a specific metallurgical flow sheet.During resource modelling, the mass magnetic recoveries and concentrate grades may be estimated directly or assigned to a block model using regressions with other chemical constituents. For estimation, the concentrate grades are weighted to account for the different mass magnetic recoveries of each sample and the impact of these differences on the concentrate estimates.

Sep 5, 2011

By J Field

Many aspects of water use in mining are driven by the technical requirements for water. There has been little consideration given to both the safety and the health requirements. Workers in the mining industry are exposed to water from a range of treated and untreated sources. The intended use of this water dictates the required quality of the water, sometimes with limited consideration for contact with miners. Particularly for underground workers, there is exposure while working in and walking through groundwater possibly contaminated by hazardous substances. Where controls are inadequate the outcomes of this exposure can result in disease, illness and injury û the costs of which can be significant. The situation could also arise where, due to the lack of human exposure, the controls are unwarranted and the financial cost unjustified from a health perspective but warranted from an equipment management standpoint. In addition to the health aspects, water can impact on a range of safety issues resulting from high pressure usage, dust suppression, fire fighting and other processes. The protocols and procedures in place need to consider the safety issues in addition to managing water usage. The current state of water management in mines from an occupational health and safety perspective has been ascertained from a survey targeting underground and surface coal and metalliferous mines. This survey considered the health and safety issues associated with water use, the types of surveillance, control protocols and the strategies that the mines have in place to manage the health and safety risks associated with water systems. The results assisted in the identification of potential occupational health and safety risks associated with water systems and the management processes that may be appropriate from a risk management perspective. Health and safety issues are often neglected but remain critical issues affecting the value of water to the mining industry.

Jan 1, 2006

By S Liu, N M. Rana, A Take, N Ghahramani, D Clohan, S McDougall, S G. Evans, H J. Chen

Tailings dam breaches have caused significant life loss, social, economic and environmental damage in recent years. The term "tailings-flow" refers to various forms of tailings outflow movement resulting from the breach of a tailings dam. These flows, comprising a mixture of tailings, water and dam materials, can take different forms, ranging from a debris flood to a flowslide, and can travel long distances and impact large areas. The inundation extents depend on the failure mechanism, tailings dam height, total released volume, sediment concentration (associated with the rheological behaviour of the flow) and downstream conditions (including topography, land cover and presence of a water body). Numerical runout modelling of tailings dam breaches is important for predicting the dynamics and extent of tailings-flows, which are crucial steps in tailings dam consequence analysis and risk management. This paper presents a comparison of numerical simulations of the 1994 Merriespruit tailings dam breach using three numerical models: DAN3D, FLO-2D and MADflow3D. Using compiled site condition information and data from the literature and public domain, model performance was evaluated primarily based on comparisons between the observed and simulated inundation extents. The main purpose of this preliminary model benchmarking exercise was to help us evaluate the capabilities and limitations of each model, and to identify opportunities for future model improvements as part of a broader research initiative known as CanBreach. This exercise also highlights the inherent complexity of tailings-flows and the importance of using judgement to interpret model input and results.

Jul 1, 2021

By K Brown, J Webster-Brown

Coal mining activity first began on the West Coast in 1864 and has since led to the exposure of large areas of coal and host rock to chemical weathering. These exposed abandoned workings have led to the formation of acid mine drainage, which flows into selected rivers and streams impacting on the natural environment. A previous study conducted for the West Coast Regional Council identified four catchments receiving mine drainage which had elevated arsenic concentrations. The aim of this research is to expand on this initial study by determining the spatial distribution and attenuation of the arsenic within the sediment and water column in each stream of concern. Cannel Creek is influenced from drainage from the Bellevue coal mine adit and exhibits a low pH of ~3, elevated sulfate concentrations and high arsenic and iron concentrations in the sediments. This pattern is repeated in the Rapid Stream and Soldiers Creek catchments, which are also affected by adit inflows from the Sullivan and Blackball coal mines respectively. Soldiers Creek also has significantly high arsenic in the waters, with an accompanying pH of ~5.5. Snowy River exhibits a similar trait with a pH also of ~5.5, but with very low sulfate concentrations. Arsenic concentrations in the waters are consistently around 30 ppb, with sediment concentrations up to 900 ppm. These sediment values might be partially attributable to the operation of the Snowy battery gold ore production facility, but the consistently high As concentrations in the water column and in the sediment upstream of the battery have an as yet unconfirmed source.

Jan 1, 2002

By R Ahola, M D. Henschel, M A. McParland

With the introduction in recent years of third-generation interferometric synthetic aperture radar (InSAR) techniques, monitoring of mine slopes, benches and surrounding areas has benefitted from increased accuracy and coverage. Fundamental research into point and distributed scattering techniques has pushed the use of InSAR to provide higher spatial and height resolution. In this paper we discuss the operationalisation of third-generation InSAR techniques and show its application to active mining operations.This paper will discuss the use of multiple independent measurements of ground movement obtained from operationally-derived InSAR products over a wide variety of deformation areas within an active open pit mining operation (ie pit slopes, dewatering depressions, tailings containment and waste dumps). A technique that shortens the time between observations (increased observation frequency) and provides ongoing estimates of measurement accuracy will be described. The methodology exploits available satellite data by using multiple satellites and multiple beams. The paper will also examine factors in the design of a mine survey with third-generation InSAR and illustrate some of the necessary engineering trade-offs to efficiently monitor a mine from space.Overall, this paper aims to demonstrate the capabilities and advantages of operational third-generation InSAR techniques for ground movement monitoring of mining operations and provide a framework for proper design of a mine InSAR survey.CITATION:Henschel, M D, Sato, S, Ahola, R and McParland, M A, 2014. Designing interferometric synthetic aperture radar surveys for mine monitoring with accuracy assessment, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 233–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By Z Gao, D Liao, W Sun, S G. Pooley, J Wang, Z Shi, G Jing, S Ren, Q Chen

Yuanjing processing plant is a scheelite and wolframite plant in southern China. Water shortages and recent environmental regulations mean that the plant must reuse the wastewater that comes from the mining operation. This paper describes the efforts to reuse the mining and ore washing wastewater (MOW) in the processing plant. Initial attempts to reuse the MOW in the strong magnetic separation were unsuccessful because the magnetic media pack was seriously fouled by the micro-fine precipitate generated. The focus changed to reuse the MOW in the scheelite flotation circuit, which includes one roughing, one cleaning and three scavenging steps. Laboratory batch tests showed this would likely be successful because using MOW reliably improved the flotation performance in the laboratory tests. Then a 20 day industrial trial was run in the plant. The trial was very successful with the enrichment ratio of WO3 increasing from 17.4 to 23.6, while the recovery remained around 79.2 per cent. The industrial trial was so successful the company immediately adopted the new scheme, which has remained in use ever since. This technical solution not only alleviated serious water shortages, and satisfied environmental regulations but also improved the plant performance.

Aug 24, 2022