Search Documents

By G J. Keyter, P J. Terbrugge, Yu Xianb

There has been disappointingly little development in the understanding of the behaviour of rock slopes in open pit mines over the past 30 years. The lack of development in general, and of robust, standardised approaches in particular, are surprising in view of the æultraÆ deep open pit mines that are being developed to depths in excess of 1000 m. Research has recently been carried out into the occurrence of zones of extension strain in open pit slopes. This showed that very large zones of extension strain can occur, and this finding represents a significant new aspect in slope stability that has not been considered before. The greatest magnitudes of extension strain occur near the toe of the slope, either in the slope itself, or in the floor of the pit. Results of the research will be presented for different slope heights, slope angles and horizontal to vertical in situ stress ratios. The magnitudes of the strains are considered to be large enough to result in fracturing of intact rock, and the fracture orientations predicted are adverse for slope stability. Fracturing that is extension in nature is common in competent, brittle rocks and often develops with some violence and little or no warning, producing easily measurable seismicity. In the slope situation, the expected physical manifestation of this behaviour would be popping off of rock slabs and plates of rock from slope surfaces and popping up of the pit floor, as well as the formation of new fractures within the rock mass. Such behaviour may cause overall slope failure, or may initiate failure, which may then be driven to overall slope failure by other influencing factors or combinations of factors. In addition to instability resulting from the fracture surfaces themselves, all induced fracture surfaces could interact with natural geological structures to facilitate formation of a significant failure surface. Case studies of slope failure in two open pits will be described. In both cases failure occurred æsuddenlyÆ after very limited amounts of deformation. In the first, the slope crest moved suddenly upwards and backwards over a length of more than 200 m, with associated instability. In the second, the horizontal displacement of the slope face was almost an order of magnitude greater than the vertical displacement and occurred æsuddenlyÆ. A recently installed seismic system is detecting events in a significant zone behind the slope face. Both pits were in the 200 m to 300 m depth range at the time of the occurrences.

Jan 1, 2003

This paper briefly reviews the background of mobile primary crushers and their current main areas of application. The benefits of applying mobile primary crushing and belt conveying systems are analysed. The impacts of applying such systems to different steps of the mine process are discussed, including mine development and planning. Application examples are used for demonstrating further possibilities to apply mobile primary crushing and belt conveying systems in mining projects successfully.

Jan 1, 2007

By Dunlop A. C

A brief study from the Mt. Bulga prospect com- pares the chemistry and mineralogy of different soil fractions and other materials to suggest a sequence of surficial metal dispersion from adjacent gossans, which may have relevance for geochemical exploration in semi-arid terrains. v v v v v JIV-- v v v v a o v o/ v v v v 1 v v lv ./v '' 1 v 16400N ..I v 1635014 v 1630014 .:1 ò.t SILURIAN sillstone " lelsic volcanic sillstone -sandstone ORDOVICIAN Eandesite o quartz float gossanò pits doOP Iv o shalt v _--'fault v 1---1 soil traverse v v v v 0 100 200 mm e Fig. I Local geology and location of soil traverses, Mt. Bulga (compiled from Chisholm, 1976). The Mt. Bulga prospect in central New South Wales is a small but well documented volcano- genic massive sulphide occurrence (450,000t of 0.8% Cu, 1.3% Pb, 5% Zn and 0.45 g/t Au) Cambrell and Kirk (1974), and Chisholm, (1976). Mineralization is localised near the interface of felsic pyroclastics with overlying silt- stones and along adjacent faults (Fig. 1). In this area with a Koeppen type cf6 climate, soils are thin and skeletal along ridges with thicker and better differentiated profiles with a colluvial component up to 2m thick developed

Jan 1, 1988

This paper describes operational experience with seam gas and spontaneous combustion management, gained during ten years of production history (1993 to 2003) in the Wynn seam at Dartbrook Coal mine. In addition, comparisons are made with more recent operational experience in the overlying Kayuga seam. Development and retreat longwall operations were undertaken in a 4.0 m thick working section of the Wynn seam, contained within the lower quarter of a circa 24 m thick mega seam, from 1993 until mining operations were relocated to the overlying Kayuga seam in 2004. Production from the first block of the Kayuga seam is currently underway with seam gas and spontaneous combustion management requirements being refined as further operational experience is gained. Seam gas management techniques, including pre-drainage with pressurised fracturing, surface to underground goaf drainage of a carbon dioxide rich seam gas and novel, high capacity ventilation circuits, were employed in the Wynn seam. Ventilation strategies included operating up to carbon dioxide STEL concentrations of 3.0 per cent in segregated return airways rather than being limited to the TWA-TLV concentration of 1.25 per cent. The spontaneous combustion experience at Dartbrook Coal has, to some degree, resulted in a change in the way the risk is managed in Australian coal mines. Values of carbon monoxide make and hydrogen concentrations are profoundly different from previously recommended management plan trigger levels and those used elsewhere in the industry. However, the detection of higher hydrocarbons together with rising oxygen depletion ratios and absolute hydrogen concentrations remain as indicators of advancing spontaneous combustion events. In this respect, experience gained in the Wynn seam was important in the initial management of the shallower Kayuga seam, an essentially greenfield site with no prior operational experience being available.

Jan 1, 2005

By T Connor

Alkali emissions are one of the environmental challenges facing alumina refineries. Queensland Alumina Limited (QAL) is undertaking a number of initiatives to continuously improve its environmental performance. One of these is a program aimed at the reduction of alkali emissions. Alkali emissions originate from a number of sources (eg elevated open tanks), and its level depends on a number of process parameters/ mechanisms (ie splash filling, thermal currents in tanks, streams discharged from a pipe, tank temperatures, atomisation) and climatic conditions (eg wind speed and direction, rain, etc). Under normal operating conditions, there is a continuous low level of alkali emissions from the plant. Certain vessels within the plant have been identified as major contributors to this level of emission, while certain activities within the plant contribute to a temporary elevation (æspikeÆ) of alkali emissions. QAL developed a method using phenolphthalein-treated pads to measure emissions within and outside QAL boundaries. These provide no information about mass emission rates but are important for detecting if alkali material is present. Since mass emission rates are important for determining if improvements in emissions are made, QAL identified the need to design an improved sampling method. Following the development and implementation of a sampling and analysis method to monitor alkali emission concentrations, QAL is conducting a number of feasibility studies evaluating a range of alkali emission reduction options. The alkali measurement method will be used to track and demonstrate progress in this environmental initiative. This paper will discuss the measurement method and emission reduction options being evaluated.

Jan 1, 2005

Magnesium-rich olivine is used as an additive in LKABÆs iron ore pellets in order to improve the high-temperature properties of the finished products. Olivine is only added to the pellets that are manufactured for ironmaking in the blast furnace process. The olivine comes from Minelco/LKABÆs mine at Seqi in Greenland. This dunite complex of Archean age contains about 95 - 98 per cent olivine. The grain size is typically 1 - 3 mm but much larger euhedral olivine crystals are common in the porphyritic type. The serpentinisation is absent or weak. The most common minor minerals are chromite, chlorite, talc, phlogopite, amphibole and pyroxene. The crushed olivine is transported to LKABÆs pelletising plants in Northern Sweden. After grinding, small amounts of olivine are mixed with the magnetite concentrate. The concentrate is rolled into green balls, about 10 - 14 mm in diameter. The moist green balls are transferred into the pelletising machine where the maximum temperature is about 1250¦C. The residence time in the pelletising machine is about one hour. Olivine is used in order to get pellets with better high-temperature properties. This paper deals with the olivine alteration during the pelletising process and the behaviour of magnesium following the decomposition of magnetite. The reactions are quite complex in the pellets because the physico-chemical conditions vary considerably in the process from one process step to another, and in the pellet bed from the top to the bottom. Some olivine particles in the finished product show very slight alteration, some particles are completely decomposed. The formation of the iron-rich coronas around the olivine particles is the most typical alteration. In the finished pellets the magnesium is mainly distributed between the following phases: unaltered olivine, coronas, Mg/Fe-ferrite and silicate slag.

Jan 1, 2008

By Belton G. R

The kinetics of the interfacial reaction of H2O on liquid silica-saturated iron silicates has been studied by means of measurement of the HDO-H2 isotope exchange reaction. The apparent first order rate constant, ka, was found to be inversely proportional to the H20/H2 ratio, consistent with two electron (melt to adsorbed/dissociating molecule) transfer mechanism and can be given by the expression In ka = -1.97 x 104/T + 1.57 - ln(pH2O/pH2), where the units for ka are mol cm -2 s-1 atm 1. The results of the current study are shown to be consistent with the indirect measurements of earlier work.

Jan 1, 1987

By He BQ

Static attachment of bubbles to solids is contrasted with dynamic attachment in flotation cells. The times of contact during particle-bubble collisions in dynamic attachment are compared with the induction time determinations and the kinetics of thinning of the liquid films separating solids and bubbles. The thinning is examined mainly in terms of electrostatic and dispersion (van der Waals) contributions to the disjoining pressure existing in the films. The local heterogeneity (on a molecular scale) of charge distribution invariably present at all interfaces (even at conditions of zero zeta potential) calls for some means to minimize possible electrostatic repulsions which arise when the electrical double layer at the air-bubble interface begins to overlap that present at the solid surface, on encounter between particles and bubbles. It is postulated that dipoles of frother molecules, owing to their ability to "flip over" (polarise), replace localized electrostatic repulsion by attraction within fractions of a milli- second, as long as the structure of the frother molecules is sufficiently "bulky" to maintain diffuse films (of mixed collector-frother) at the air/liquid interface of bubbles. The relaxation times of dipoles (signifying their "flipping over" ability) have to be shorter than the collision times between particles and bubbles for particle-bubble attachment to be facilitated under dynamic Conditions.

Jan 1, 1984

By A D. Bugarski, G H. Schnakenberg Jr

An investigation was carried out at a US underground mine to characterise diesel aerosols and to asses the effects of various control technologies on the concentrations and properties of particulate matter and gases emitted by heavy-duty diesel-powered equipment. This study was dedicated to evaluating the impact on mine air quality of contemporary diesel particulate filter (DPF) systems installed on mining equipment. Additional efforts were made to assess the effect of blended biodiesel fuels, yellow grease and soy, ultra-low sulfur fuel, a fuel emulsion and of selected diesel oxidation catalysts on air quality and emissions. The carbon analysis performed on the collected samples showed that the tested DPF systems reduced the mass concentrations of elemental carbon in mine air by between 70 per cent and 92 per cent. In addition, TEOM measurements, collected during these tests, showed that the total diesel particulate matter concentration in the mine air was reduced by greater than 65 per cent when DPF systems were used. The tested biodiesel blends were found to reduce elemental carbon concentrations in the mine air by between 49 per cent and 33 per cent, for the B20 (20 per cent biodiesel/80 per cent #2 diesel) of soy and yellow grease respectively and between 66 per cent and 56 per cent for the B50 (50 per cent biodiesel/50 per cent #2 diesel) of soy and yellow grease, respectively. The water-in-diesel fuel emulsion was shown to reduce elemental carbon concentrations by as much as 85 per cent. NO2 measurements showed an increase in the maximum concentrations of NO2 when catalysed DPF systems were used instead of mufflers.

Jan 1, 2005

By Ellson I. G

Shay Gap was created for the sincrular purpose of housing, in comfort, the workforce that would be required to mine iron ore, from leases held by Goldsworthy Mining Limited, in hill country, approximately 170 kilometres east of Port Hedland in the Pilbara region of Western Australia. To combat the and environment, the Company ultimately decided to adopt a novel planning concept for the town, which had not been attempted before in Western Australia. The special problems encountered during planning, and the reservations that were expressed during construction and early settle ment, are now part of the dim past. During the three years of occupation now achieved, there has been accumulated a story of success in the provision of an acceptable alternative to modern suburbia. Not only may this be claimed, but it can also be argued that the Shay Gap concept has been a more successful solution to a real environmental problem in our arid Pilbara region than has been seen in other similar settlements.

Jan 1, 1976

By Mostyn G. R

An important problem in rock engineering is to control the properties of artificial rock. A compaction technique for casting artificial rock specimens with controlled properties is described, i.e. using a compression-testing machine to compress the mixture. Uniform density is necessary to achieve uniformity of properties of the specimens, and uniform density can be obtained by using the specific pressing method presented. Rebound and borax content are important to the technique and have been studied as well.

Jan 1, 1992

By Hutchings SG, Skimmings T

This paper describes the results of the field application tests at Miike Colliery on the integrated automatization of the longwall mining system for medium thick coal seam. The purpose of the research is to develop an automatic longwall mining system which can be controlled accurately from outside of the face, and the ultimate goal is an eliminate of men from the face. Presently, the field test is being conducted in Yotsuyama mine following to a success in the performance test on surface. Remote Batch Control System for shield supports has been adapted to operate all supports from the control panel located at the entrance of the face. Remote monitoring and control system of the drum shearer has also been tested. The system makes it possible to operate the shearer either at the main gate or full automatic. Productivity and safety will be substantially improved as those systems enable to eliminate all workers from the face under the severe working conditions with high ground pressure and hot and humid atmosphere due to increasing mining depth. So far, we have been satisfied with the results of the field test and those system will be an effective countermeasure to operate the face with a high risk of rock-burst.

Jan 1, 1987

Fluid circulation occurs in oceanic crust of all ages, at the seafloor spreading axis, on mid-ocean ridge flanks, in the ocean basins, and in subduction zones. In the first three settings the fluid originates as seawater. At the axis and on the ridge flanks, the circulating seawater produces a major chemical exchange between the oceans and the crust. Based on heat budget constraints, between 10 and 40% of the river flux of Mg can be taken up during high-temperature alteration of the basaltic crust along the mid-ocean ridge axis. Most of the hydrothermal -heat loss, however, occurs on the mid-ocean ridge flanks, where the temperatures are lower and the seawater flux correspondingly larger. The estimated heat loss on the flanks is so large that upwelling must occur over a large fraction (5-30%) of the seafloor less than 65 Ma in age, at seepage velocities on the order of 10 to 100 cm/yr. The circulating seawater need lose less than 1 to 2% of its Mg content in order to solve the Mg mass balance for the oceans. Fluids in subduction zones are commonly less saline than seawater and are rich in methane and other light hydrocarbons. These fluids may originate by dewatering of the downgoing slab. If so, they may close the geochemical cycle of H2O that began with hydration of the basaltic crust at the ridge axis.

Jan 1, 1990

By Juras ST, Krouse RH, Godwin CI

The Buttle Lake camp is in central Vancouver Island, southwestern British Columbia, Canada. The camp hosts world-class polymetallic volcanogenic deposits of Devonian, Frasnian age (370Ma). This paper describes an on-going sulphur and lead isotope study of the major orebodies.Sulphur isotopes were determined for sulphides (pyrite, chalcopyrite, bornite and galena) and sulphate (barite). Sulphide analyses are markedly different from sulfate. The differences are explained below in a unique model.Sulphide isotopic compositions cluster tightly (del34S -6.7 to 4.6), and demonstrate isotope reversals. Calculated temperatures of correctly ordered mineral pairs are unrealistically high. We conclude that the sulphides are in isotopic disequilibrium, presumably because of rapid precipitation from a quenched plume in an anoxic environment, and because of subsequent sulphide replacement.

Jan 1, 1990

A general review of grinding mill steel liner evolutions/developments in recent times. The driving force behind these developments has been the mill operators desire to minimise the nett cost of their operation. These developments have resulted from a team approach between supplier, operators and reline crews. The move towards larger diameter high aspect mills, faster mill speeds, pebble ports and the use of large diameter grinding media has affected the traditional liner designs, which is placing higher demands on the supplier to meet these new working parameters and expectations. Operators are also taking closer ownership in the liners being supplied, as demonstrated by the development of their own mill liner specifications. This paper outlines some of liner developments and changes undergone at various milling operations around Australia and overseas (such as Cadia Hill, Kidston, Ok Tedi Mining, PT Freeport, etc) and where to in the future?

Jan 1, 2000

By I Gipps

The mining industry has come through a period of major change in community expectations regarding safety and environmental impact and these changes can be expected to continue in the future. These changes are ultimately reflected in Government regulations and industry safety standards and form the basis of the ælicense to operateÆ. Equally, advances in technology have made possible new equipment and processes either available now, or close to completion, that will allow mines to meet these more stringent expectations if properly introduced. Changes in technology provide opportunities for mine management to introduce new systems that will remove people from hazardous areas and lead to improvements in the ætriple bottom lineÆ. In a longer time frame of five to ten years, novel and advanced technologies that are currently being developed will deliver new mining methods and conversion of presently uneconomic resources to ore. This is consistent with the time frame required to develop a new mine from discovery. Strategic decisions can be taken now by mine designers to enable the introduction of these major technology changes. Examples of both practical and strategic opportunities are drawn from the integration of rock cutting/blasting, automation, electronic communications and new mining methods. This paper discusses emerging industry trends, changes to legislative framework and some practical choices for existing and imminent technology.

Jan 1, 2003

By S C. Dominy

The Bendigo Goldfield is located in the state of Victoria, Australia, and is one of a number of quartz-reef fields that make up the greater Central Victorian Goldfield. At Bendigo gold particles are characterised by their very coarse nature, ranging from below 100 to over 10 000 ¦m in size. Some 60 per cent of the gold occurs in particles greater than 1000 ¦m in size. This characteristic ensures that the mineralisation is very challenging to both sample and evaluate. Diamond drilling provides a measure of geological structure, but is a poor measure of in situ grade, understating it by up to 75 per cent. Drilling combined with on-reef development, bulk sampling and geological interpretation has been used to define Indicated Mineral Resources. For grade control, a balance had to be sought between sample representivity, cost, turn around time and practicality. Sampling of extreme nugget effect deposits generally requires the use of bulk sampling in order to be representative. However, the cost and turn around time is significant. As a result, a 50 kg micro-bulk sampling system has been introduced that attempts to overcome these problems by providing a fast, practical method that can discriminate between ore and waste. As the mine passes into production, grade control will increasingly become dependent upon geological data collection and interpretation.

Jan 1, 2005

By Y Bissiri

The ever increasing demand for metals and minerals is putting significant pressure on current mining companies to find more ore. As these companies explore and mine, the future appears to be to go deeper and deeper underground. With depth, however, comes ever increasing costs as infrastructure such as hoisting, ventilation, the movement of workers and materials increase in size and scope. Further, the actual rock mass becomes prone to destruction through rock bursts and the heat generated becomes a major issue resulting in extreme expenditures in cooling plants and some of the biggest air movers in the world. All these issues result in dramatic changes in both capital and operating costs, subsequently making cut-off grades rise. As this trend continues there is an economic limit to how deep one can go, resulting therefore in a severe shortage of accessible ore deposits to mine. This paper discusses the need for larger marine robotics technology and presents the state-of-the-art in current research in underwater tele-autonomy, specifically the development of high bandwidth optical communication networks critical to any future activities (mining, construction, etc) underwater. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

The mining. operations of Bougainville Copper Pty Limited are located at Panguna on the Island of Bougainville which is part of the Territory of Papua and New Guinea. Mineralisation in the Panguna area was first established by C.R.A. Exploration Pty Ltd in 1964. Exploration work since then has established ore reserves estimated to be 760,000,000 tons of.0.47% copper and 0.4 dwt./ton gold. An economic feasibility study completed in July of this year has enabled a decision to be made to proceed with a major mining operation. The ore will be mined by open cut methods and will be treated in a conventional concentrator with a nominal capacity of 90,000 short tons per day. The concentrate will be pumped as a slurry through a 15 mile long pipeline to a port established on the east coast where it will be filtered and dried ready for export. Other supporting facilities for the mine include two towns, a 135 megawatt steam power station, and access roads.

Jan 1, 1970

By Van Hoorn PD

For the development of BHP's Gregory open cut coal mine in Central Queensland a mini computer was successfully used to assist staff in the evaluation of the deposit and the planning of the mine. The Gregory deposit is essentially a single mineable seam deposit, however the systems developed may be applied to other coal deposits including multi seam occurences. The first phase of the Gregory computer evaluation and planning project involved the establishment of a borehole data base for the storage, retrieval and analysis of both strata and quality data. During the second phase a numeric block model of the coal deposit was created. Using this model reserve calculations were carried out by specifying the area with the aid of a digitizing tablet. The third phase involved the develop- ment of systems to simulate the dragline stripping operations including the rehandle percentage calculation, a dragline production schedule showing coal quantity and quality exposed, and a combined multi dragline operation schedule that can produce figures and graphs for up to 20 variables. A derivative of the operating plan was a programme that gave productioh cost estimates

Jan 1, 1978