Search Documents

By P M. Ashley, M T. Costelloe

The Mary Kathleen tailings storage facility (TSF) contains 7.1 Mt of uranium mill tailings. This waste repository was rehabilitated in the mid-1980s using a multibarrier dry cover. At the time of mine closure, it was predicted that acid mine drainage (AMD) generation would not eventuate and that uranium, heavy metals and radionuclides would be adsorbed within the tailings and not seep from the TSF into the environment. This study reports on the environmental status of the TSF. Gamma-ray measurements indicate an intact dry cover of the waste repository. However, seepage (~0.5 L s-1) of acid (pH 5.71), saline (0.31 per cent), high conductivity (8.8 mS cm-1), slightly oxygenated (DO 2.6 mg L-1), radioactive waters occurs from the toe of the tailings dam into the former evaporation ponds and local drainage system. Seepage waters are calcium-magnesium-sulfate rich with elevated Fe, Mn, Ni, U and Zn values. Oxygenation of tailings seepages causes the precipitation of Fe and coprecipitation and adsorption of other metals (Pb, U, Y), metalloids (As), rare earth elements (Ce, La) and radionuclides (U-235, U-238, Th-227). In contrast, Ba, Ni, Sr, Mn, P, S, Ca, Mg, Na and K as well as Ra nuclides (Ra-226 and Ra-228) remain in solution until pH neutralisation and evaporation lead to their precipitation in efflorescences and sulfate-rich evaporative sediments further downstream. Dry capping of Mary Kathleen uranium mill tailings has resulted in physical containment of the wastes. The dry cover shows no signs of erosion and radiation levels are within acceptable limits. However, the flow rate of surface seepage from the TSF occurs at a much higher rate than predicted. Also, the neutralising potential and adsorption capacity of the tailings and underlying aquifer were overestimated at the time of mine closure. AMD has developed mobilising metals, metalloids, rare earth elements, alkalis, radionuclides and sulfate from the waste repository into surface water seepages.

Jan 1, 2003

By R Cunningham, P Duniam

Late in 2005 it became apparent that cave propagation at the Northparkes Mine was not progressing as planned. By mid-2006 sufficient Reserves were identified to warrant an extensive drill and blast program to assist in cave propagation. This program began late in 2006 and concluded early 2007. A significant challenge faced was the drilling and blasting of holes between 75 - 240 m in length in the South Wedge in Lift 2 at Northparkes Mines E26 orebody. The project set new benchmarks in production drilling and charging in underground metalliferous mining. This paper discusses the drill and blast designs, the challenges and the operational issues encountered with this project. Also highlighted are ways in which these were overcome.

Jan 1, 2007

The Crown Minerals Act provides a new+framework for the management of Crown owned minerals and requires that regard be had for the principles of the Treaty of Waitangi. The Act requires the preparation of Minerals Programmes to achieve the Act's objectives of efficient allocation of rights and the recovery of a fair financial return on its minerals. Efficient allocation requires that a permit is allocated to the party which values it most highly. A fair financial return to the Crown must be considered in the context of the economic rent available from individual mineral projects, with the proviso that a nil return to the Crown as the owner of the resource will not be considered a fair return from the community's perspective.

Jan 1, 1992

Crushing Plant Process Optimisation Design of processes in order to find the most efficient solution to a specific task is a difficult problem. Often the number of solutions are large and the optimal solution is therefore difficult to identify. Crushing plant process design is no exception from this statement. In order to find the best solution issues like equipment selection and process configuration must be mastered. The solution must both be technically feasible and preferably have a low operating cost. Since crushing plant design is a complex task with a large solution space it is basically impossible to master without a specialised tool. For a long time simulation softwares have been used to assist in the design process. These tools only give answers for how a user defined plant will operate. There are no tools with capabilities to consider different design options in order to determine what the most efficient solution looks like. In this paper a method for crushing plant design optimisation is presented. The novel method utilises a combined optimisation routine and expert system in order to find the most cost efficient solution to a given process task. The user will only need to define the feed material properties, the process capacity, and the end product requirements. The developed system will find the solution lowest production cost per ton.

Sep 13, 2010

By Ramsden AR, French DH

The limited contrast range of conventional black and white imaging does not enable full use to be made of the dynamic range of the video signal obtained from a scanning electron microscope or microprobe. The use of false colour substantially increases the information that can be derived from such images enabling relationships to be displayed that cannot be observed in black and white. This capability is now used extensively in combination with quantitative electron microprobe analysis as a research tool for ore characterization and host rocks studies related to minerals exploration in the CSIRO Division of Exploration Geoscience.

Jan 1, 1989

By C E. J de Ronde

Most of the world's economically significant volcanogenic massive sulphide (VSM) deposits are considered to have formed in submarine arc and backarc settings. While the Kermadec-Tonga arc is an excellent example of an intra-oceanic arc setting, it remains largely unexplored in terms of submarine mineral resources. More than half of this arc (~1400 km of the >2500-km-long feature) lies within the EEZ of New Zealand, where it is defined by at least one sub-aerial and 33 submarine volcanoes. The NZAPLUME (New Zealand American PLUme Mapping Expedition) cruise of March 1999 provided a systematic assessment ofhydrothermal activity on the southernmost 13 submarine volcanoes along the southern Kermadec arc. Using prospecting techniques based on the physical and chemical detection of hydrothermal plumes, we discovered that more than half (7 of 13) of the southern Kermadec volcanoes host one or more active hydrothermal systems at depths ranging between <200 to 1800 m. Chemical results show that the fluids discharged are compositionally diverse among volcanoes and between sites at a single volcano. Plumes over more than half of the volcanoes are gas-rich (He, CO2, H2S) relative to mid-ocean-ridge (MOR) plumes. In addition, most sites are highly enriched in Fe, yielding Fe/Mn values that far exceed those for MORs. One interpretation consistent with these observations is compositional overprinting by addition of magmatic fluids, which are typically highly enriched in gaseous and ionic components. Regardless of the source, it is clear that the ligands (HS-, Cl-) required to efficiently transport base (e.g. Cu, Zn, Pb) and precious (e.g. Au, Ag) metals to the seafloor are abundant in Kermadec arc fluids. We conclude that modem analogs of VMS deposits are likely forming at multiple sites along the Kermadec arc and within the EEZ of New Zealand.

Jan 1, 2000

Burra was the largest metalliferous mine in Aus- tralia between 1845 and 1860 and employed as many as 1000 men and boys. The workforce was predominantly Cornish, Burra being the first con- centration of Cornish folk in Australia. The sur- face and underground mining operations were typically Cornish and virtually all positions of responsibility were held by Cornishmen. Beam pumping and winding engines were imported from Cornwall and housed in traditional Cornish engi- nehouses. Burra had the first significant number of beam engines in Australia: six were installed between 1849 and 1861. These engines, ranging in size from 20 inches to 80 inches in diameter, were used for pumping, hauling, and driving Cornish roll crush- ers and dressing machinery. Derelict enginehouses of the great beam engines are a striking reminder of former mining activity in Cornwall and South Australia. In South Aus- tralia about 35 enginehouses were erected between 1848 and 1887, of which eight still remain, three of them at Burra (Figure 1). These remain as a tangible link with the Industrial Revolution.

Jan 1, 1987

By M L. van Kampen

The recent (2005) amendments to the Resource Management Act 1991 have made it clear that there is no obligation on an applicant to consult. However the importance and value in consulting with the community, particularly before commencing a major project, cannot be understated.   This paper looks at the provisions of the Resource Management Act as they relate to consultation and public participation in the process, and will discuss the benefits of consultation both before an application is filed and following the filing of the application. Engaging with the local community can help shape a project to better fit the community, engender support and address opposition. In short, taking the extra step to what is legally required, can help smooth what is potentially a bumpy road. Examples in practice of the value of consultation are given.

Jan 1, 2006

The Resource Management Act has been in force now for approximately ten months. This Act, and the Crown Minerals Act which accompanied it, have substantially changed the manner by which mining operations and other resource uses obtain access to resources and are subject to controls of their environmental effects. This paper briefly summarises the key elements of the regulatory provisions of the Resource Management Act. It identifies the types of resource consents required, and discusses these and procedural matters in relation to mining in Otago. It addresses the transitional provisions and highlights inconsistencies and difficulties in the implementation of these provisions. This paper identifies potential future developments in the planning and regulatory environment relating to mining in Otago.

Jan 1, 1992

The problem of stability of the development working at the great depths of coal winning is of great seriousness. Numerous researches of the problem were carried out in the USSR, the results of which determined that raising of resistance of existing support will not lead to a considerable rise of working output. It is necessary to try to find ways at the expense of heightening the support ability of rock massif. For these purposes it is necessary to direct it correctly and in proper time. While carrying the development working the most intensive deformations of rock occur at a depth of 30m from the entry face. The zone of destruction of rock around the work is realised here for 60 to 70 percent. These facts show that in influence zone of entry face a kind of embryo of the working steadiness is forming, which greatly determines its following conditions. Therefore, it is necessary to begin direction of mining pressure around the work directly in a face.Complex research of the mechanism was carried out starting with the effect of moving face upon the surrounding rock massif. It was ascertained, that the zone influenced by the face is a section of 5 equivalent diameters of the work by the length within which the rock of the sides, roof and floor, experience the cyclical influence of stresses at the time of cyclical shift of the face. The elastoplastec deformation is occurring with it at the moments of rock removal and the deformation of creeping takes place at such intervals.

Jan 1, 1991

By J Morton

The Resource Management Act 1991 represented an innovative and unique piece of planning and environmental legislation when it was introduced. Since the Act was passed into law in 1991 it has been subject to nine amendments, many of which were of the ætinkerÆ variety. These amendments recognise that the Act has not been as successful in providing the æone-stop shopÆ for resource users that the Act was hoped to be. The latest and most significant attempt at changing the Act was the Resource Management Amendment Act 2003. The amendments made by the Amendment Act have proved to be largely unsuccessful in achieving any significant changes to the way resources are managed in New Zealand, and have failed to address many of the concerns which drove the original Resource Management Amendment Bill in 1999. The recent decision to discontinue further investment in Project Aqua has once again placed the Act in the spotlight as a significant hand-brake on major projects. This particular event has led to yet another review to be undertaken this year. The review will focus on five key areas:   1.   achieving the right balance of national and local interests; 2.   improving the design and process for local policy formulation; 3.   improving the consent decision making process; 4.   allocation of natural resources (water, air and geothermal); and 5.   supporting measures for building capacity and promoting best practice and implementation at the local authority level.  It is important for the business community and the mining industry in particular to seize the opportunity that this review provides to make sure that any amendments undertaken as a result of the review achieve the aims listed above. The review needs to be considered in light of the current regime for the management of natural resources in New Zealand. In addition to the Resource Management Act 1991, the Crown Minerals Act 1991 and the Building Act 1991, which form the core resource statutes in New Zealand, there have been other developments affecting the regime. Special legislation over and above the Resource Management Act 1991 has been enacted to protect the Hauraki Gulf and special legislation is currently being considered to protect the Waitakere Ranges in Auckland. In the Hauraki District mining is prohibited in some areas and a plan change mechanism is specified as the appropriate tool to use in the event a mineral resource is to be developed in those areas. The current review is a further opportunity to remedy the inadequacies of the Act.

Jan 1, 2004

The offshore Maui gas/condensate field was discovered by Shell BP and Todd on Services Limited in 1969. Subsequent appraisal drilling and negotiations with the Government led to a development agreement, æThe Maui White Paper' being concluded in 1973. Part of this agreement provided for the Government to take a 50 per cent shareholding in the field. The field is comprised of a double domed anticlinal structure containing two gas reservoirs at depths ranging from 2700 - 3000 m. Water depth is 110 m. The development plan called for two standalone steel platforms to be installed sequentially over a period of some years depending on gas demand. The first platform (MPA) was put in place in 1976 but difficulties were experienced with piling and drilling of the 12 (later increased to 14) wells did not start until 1978. First gas was piped ashore late in 1979.

Jan 1, 1994

The minerals industry focus over much of the past twenty years has been on cost reduction and production growth supported, but not driven, by technology improvements. Mergers and acquisitions, and the demands of financial markets, have been high priority items whereas research and development and technology based innovation have received less attention and have been cut back in many companies. Technology improvements will be critical if the industry is to make progress on the stated aims of improving energy efficiency, reducing water usage and maximising recovery from deposits. They will also be important for improving capital efficiency and in treating difficult deposits. However the role technology based innovation will play both in the overall industry, and within individual companies, during the next decade is quite uncertain. There are major challenges in progressing technology based innovation in an industry with limited technical resources which is dominated by long life high capital operations. Specific opportunities for energy and productivity improvements exist but face significant technical and structural barriers that need to be overcome if the industry is to significantly improve performance. Current evidence suggests that changes in approach will be needed for these improvements to be realised. Recent studies in the United States and Canada have highlighted the wide range of energy performance across the industry and the scope for marked improvement from both incremental improvements and increased research and development. Comminution, material transportation and underground mine ventilation were identified as high priority areas. Opportunities within these areas are discussed both in respect of specific technologies and in how they may change performance. The role of open innovation as a source of new technology is also discussed. This is an abstract only. No full paper was prepared for this presentation.

Sep 13, 2010

By Waterhouse J. D, Harris B. M

This paper briefly describes the construction in 1979/80 of a 70m deep trial open pit coal mine near Bowmans S.A. and describes more fully the hydrogeological aspects of the exercise. The primary purpose of the Trial Pit was to provide a large sample (700 tonnes) of coal for combustion tests to be carried out in West Germany and the United States of America. Consideration was given to obtaining the sample of coal by drilling and by shaft sinking as alternatives to open pit methods. It was expected that economic mining of the deposit on an operational scale could only be achieved by open cut methods and it was recognised that major uncertainties existed in planning such a mine in the deep unconsolidated multi-aquifer deposit. It was therefore elected to obtain the bulk sample by constructing a trial open pit, which would be closely monitored to provide as much data as possible for future planning of a full scale mine. The dewatering of the Trial Pit was achieved using 26 deep pumping wells, assisted in the later stages by several hundred well points. This was probably the largest dewatering project currently in operation in Australia.

Jan 1, 1981

The OK orebody comprises a steep dipping narrow quartz reef averaging 0.4 m in width hosted in basalt and gabbro with porphyry bars cross-cutting through it. The following paper tracks the mining of this orebody, challenges encountered, measures undertaken to address these challenges and changes in mining conditions and methods as the mine matured in both depth and age. The initial mining method was narrow vein hand held shrink stoping accessed by shaft, that over the period of the mines life was superseded by gallery stoping, shrink stoping and ultimately mechanised narrow vein long hole sublevel open stoping. The reasoning behind the change in mining methods is detailed, including safety and cost benefits. The transition presented many challenges that were overcome, resulting in the successful development of a narrow vein long hole stoping method. The lessons learnt during the transition period and the practices and principles developed for successful mining of narrow vein orebodies using long-hole open stoping methods are summarised in this paper. The final section of the paper takes a retrospective view of how the knowledge gained through the mining of the OK orebody would be applied to a new mine containing an orebody of this type, with consideration given to the initial excavation design, equipment selection, mining sequence, geotechnical investigations and mining method used.

Jan 1, 1998

Listing on Australian Stock Exchange Limited ('ASX') is a means by which a company can prosper and grow by gaining access to a large capital market. This currently stands at over $300 billion for domestic securities listed on ASX. A company seeking listing will benefit from a higher profile and a greater spread of shareholders. These result from, among other things, improved communications with the investment community. ASX recognises that a decision to list is an important step for a company. Owing to the diverse nature and size of the companies that consider listing and the various steps involved, it is recommended that guidance of professional advisers is sought as early as possible in the listing process. A company seeking listing on ASX must meet the prerequisites for admission to the Official List which, along with the continuing obligations that must be complied with following admission, are contained in the Listing Rules of ASX. Listing on ASX requires a company to ensure that, among other things, the market is fully informed at all times so that investors can make informed investment decisions.

Jan 1, 1996

By R G. Richards

Although most New Zealand coals are low in ash, there are situations where high ash coals could be won. Not all high ash coals can be upgraded by physical means, since the ash is either inherent in the coal or bound in such a way to make its physical removal either impractical or uneconomic. Nevertheless, the authors believe, the situations where high amounts of ash can be economically removed by physical means to make a saleable product are considerable.

Jan 1, 1979

By G Smart, D Ward, J Grace

Ridgeway Gold Mine is part of Cadia Valley Operations which is wholly owned and managed by Newcrest Mining Limited. It is an underground sublevel cave (SLC) operation mining approximately 5 Mt per annum. Ore control systems at Ridgeway have been designed to deliver gold and copper metal production through focussing on the ore characteristics that impact on mine and mill performance and ultimately metal delivery. This is achieved using data collection and management systems which allow data to be collected digitally with æat captureÆ validation routines. These data form the basis for forecasting and on-going systems analysis which aim to accurately assess local in situ and drawn ore characteristics. Physical attributes of ore such as draw characteristics, brow conditions, visual grade estimates and draw point sampling are routinely recorded. Ore tracking and accounting systems monitor gold and copper grades, copper mineralogy, host lithology and ore sizing. These factors have material impacts on concentrator throughput and metal recovery. Draw point recovered grades are routinely reconciled back to design data to monitor and assess draw performance. Statistical variance controls are also employed to analyse mine and plant performance and guide actions.

Jan 1, 2003

Wollongong* is Australia's largest single centre of mining and metallurgy. Wollongong's total employment in manufacturing of basic metal products (over 26,500 in 1972/1973) was almost 50 per cent higher than that of Newcastle and double that of any other Australian city. Although the great bulk of this employment was in steelmaking, Wollongong's copper industry was also a significant employer. Wollongong's total employment in mining (4,900 in 1971) was second only to that of Newcastle among Australian mining centres. Although the bulk of Wollongong's mining is of coal, there is also considerable mining of blue metal, sand and clay. In all, over 40 per cent of Wollongong's work force is employed in mining and metallurgy. The great bulk of the other

Jan 1, 1976

Computation is believed to be a powerful tool in scaling-up chemical processes and in designing materials, however, is being challenged by low predictability and limited scalability. This presentation will discuss the promising future of multi-scale computation in solving these two problems to realise the real-time simulation of industrial processes. Multi-scale structures are a common nature of most chemical systems and the meso-scale phenomena are believed to be the road blocks not only in improving the predictability of physical modeling but also in extending the scalability of computation. Focusing on the meso-scale phenomena, a series of research has been carried out at the Institute of Process Engineering, Chinese Academy of Sciences, for the past three decades. Starting with a simple idea of modeling the meso-scale clusters in gas-solid two phase flows, the so-called EMMS (Energy-Minimisation Multi-Scale) model was established. In verifying the stability condition of the model, the pseudo-particle approach was proposed to explore the micro-mechanisms in particle-fluid systems, and the strategy of the EMMS model was extended to other six different multi-phase systems, resulting in a unified conceptual formulation of multi-phase complex systems expressed by a multi-objective variational problem. In applying this model to different multi-phase systems and to industrial problems, it was recognised that the EMMS model defined a new paradigm of multi-scale computation by realising the structural similarity between software, hardware and the problems to be computed. This paradigm of computation was implemented on a multi-scale supercomputer with a capacity of 1.0 petaflops by integrating CPUs and GPUs (Graphic Processing Units), showing high efficiency and low cost. Running the EMMS model on this computer, the simulation of hydrodynamics of multi-phase systems can be speeded up very much, indicating a promising future of virtual reality of process engineering. The presentation will review this series of work, introduce successful applications in industries, and will be concluded by emphasising the critical importance of the meso-scale phenomena as the bridge between macro-dominants and micro-mechanisms. This is an ABSTRACT ONLY. No full paper was prepared for this presentation.

Sep 13, 2010