Search Documents

By J. C. Swartz

Measurements of the effect of precipitation stresses on the solubility of cementite (Fe3C) precipitates in a iron are reported. Solubilities were determined from measurements of the Snoek relaxation due to interstitial carbon after quenching from various equilibrium treatments. Stress-free precipitates were obtained by a spheroidizing treatment of vacuum-melted Fe 0.06 wt pet C. Subsequent equilibration treatments were designed to suppress nucleation of other precipitates. The results for stress-free cementite give a heat of solution of 14.8 i 0.2 keal per mole and an entropy change of 1.1 i 0.2 eu in the temperature range 400" to 715°C. Comparison with previous data indicates that the heat of solution increases about 6 keal per mole as temperature increases from 700" to 1000°C. Data on self-stressed cementite in quench-aged specimens of Fe 0.013 wt pet C indicate 1) an apparent heat of solution of 12.1 i 0.4 keal per mole in the range 280" to 690°C, 2) a strain energy of- 1.1 keal per mole Fe3C accompanying precipitation at 280°C, and 3') a gradual decrease in the strain energy of precipitation with increasing equilibration temperature. In com-parison with 2 and 3 the strain energy calculated for an isotropic model is 1.7 keal per mole Fe3C. The lower values obtained from the experiment indicated substantial stress velaxation by dislocation motion. WHEN a supersaturated solution of carbon in a iron is aged at temperatures in the range 200o to 700oC, the carbon clusters by interstitial diffusion and forms cementite (Fe3C) precipitate particles. Unstressed cementite has a volume per iron atom 9 pet higher than that of a iron;' hence, cementite precipitate particles are usually under pressure from the iron matrix. The pressure would tend to increase the solubility of cementite in iron.' This report describes anelastic measurements of the solubilities of self-stressed and stress-free cementite in a iron. Previous determinations of the cementite solubility are summarized in Table I. The method of cementite formation for each reference was studied to ascertain the state of stress of the cementite. The results judged to be for stress-free and stressed cementite are distinguished in the table. In the next section an estimate of the stress effect is obtained which is clearly too small to account for the large difference between the previous results in parts A and B of the table. THEORETICAL Let AGO be the standard free-energy change of the reaction Fe3C (eem.) = 3Fe (a) + C (in a) [1] in the absence of stresses. Since cementite precipitates appear to be rather pure10 and the carbon is so dilute in the iron,8 the cementite and iron of Eq. [ I] for the stress-free case have essentially unit activities and the activity of carbon equals its atom fraction xoC Then the stress-free equilibrium is expressed by RT In XoC = -?GO 121 To first approximation the change in the chemical potential of carbon due to the precipitation stresses equals the elastic strain energy W accompanying precipitation of a mole of cementite.2 Hence, in the presence of the precipitation stresses the equilibrium is described by RT In x sq = -?G° + W [3] where xsC is the mole fraction of dissolved carbon in the stressed case. An approximate value of W can be obtained from analysis of the inclusion problem in elasticity theory. The inclusion is a small portion of the matrix phase which has suffered a transformation while still imbedded in the matrix. In the absence of the constraint of the matrix the transformation would be equivalent to a uniform dilational strain eT. Both the matrix (a) phase and inclusion (0) phase are assumed to be homogeneous, isotropic materials. When the a and 0 phases have the same elastic moduli, which is approximately true for iron and cementite,11 the total strain energy per mole ß is12 2µVß(eT)2(3 +4 µx)-I [4]

Jan 1, 1968

By J. W. Edington

THE Hopkinson bar has become a popular technique for the measurement of the mechanical properties of materials deformed at high strain rate. Maximum use of the equipment is made in the arrangement first used by Kolskyl in which a short compression specimen is sandwiched between two pressure bars and is loaded by a single pulse travelling through the system. The pressure bars are used both to apply the load to the specimen and as transducers to obtain continuous strain-time histories of three pulses, incident on, reflected, and transmitted by the specimen. The data measured by the pressure bars can be analyzed in terms of the stress/strain behavior of the specimen.2'3 However, one of the assumptions of the analysis of the observed pulses is that the total stress and total strain do not vary significantly from point to point within the specimen at any given instant during the deformation process. Although this assumption is generally justified for very short disc-like specimens2 the situation is uncertain for larger specimens. For example, at small plastic strains (-0.01) Hauser et al.2 have some evidence of small flucations in the total stress within the crystal during deformation, even in relatively short aluminum specimens. In addition, Karnes4 has shown that the plastic strain, and by inference strain rate, is different at each end of a compression specimen tested in a Hopkinson bar, although the length of the specimen was not specified. Recently, the mechanical properties and the dislocation substructure have been investigated in single crystals of columbium5 (length 0.25 in., diam 0.19 in.), and copper6 (length 0.5 in., diam 0.5 in.) deformed at high strain rates. As part of this research program the assumption that the plastic strain is constant throughout the specimen has been checked by measuring the total dislocation density as a function of position in the specimen. Compression specimens of the same orientations and dimensions were tested as described previously5,6 sing a split Hopkinson bar. Since any discontinuity in strain distribution is most likely to arise during the initial stages of deformation the investigation was performed on specimens deformed to plastic shear strains of 0.054 (copper) at a strain rate 1.2 x l03 sec-1, and 0.06 (columbium) at a strain rate 1.5 X l03 sec-1. The orientation of the single crystals is shown in Figs. 1 and 3. Thin foils were taken parallel to the most highly stressed slip plane, i.e., (111) in copper and (011) in columbium, using conventional disc techniques. The dislocation densities were measured using first order reflections with compensation for invisible dislocations.5'6 In the copper single crystals the discs were randomly distributed throughout the cross section of the specimen. However, the dislocation density obtained from each disc was plotted vs the disc positions relative to the ends of the specimen. The results for the copper specimens are shown in Fig. 1. Clearly the dislocation density is constant throughout the main portion of specimen within the experimental error. The error bars on the dislocation densities correspond to a shear strain variation of 0.015 on the basis of previous measurements% ± of the rate of increase of dislocation density with strain in copper single crystals of the same geometry. Thus within this experimental error the plastic strain can be concluded to be constant within the specimen and the assumptions used in the analysis of the stress/time curves are therefore reasonably valid. The higher measured dslocation density near the impact end and the lower dislocation density at the bar end of the copper specimen is in agreement with the results of Karnes4 who showed that this strain/time curve rose to a maximum more rapidly at the impact end compared with the bar end. Hauser et al.2 have also pointed out that at small plastic strains (-0.01) the strain at the impact end of the specimen may be greater than that at the bar end. Thin foils taken from different points within the columbium single crystals demonstrated that the dislocation density could vary significantly within the specimen, see Fig. 2. Large areas of some thin foils up to 30 µ sq contained very few dislocations, see Fig. 2(a). However, in other parts of the compression specimen dislocation configurations like those shown in Fig. 2(b) existed over large areas (-30 µ sq). As a result, when the average dislocation density in a thin foil is plotted as a function of the position of the thin foil relative to the ends of the specimen, considerable scatter is observed, see Fig. 3. In this material then, the local dislocation density, and consequently the

Jan 1, 1970

INTRODUCTION This chapter summarizes porphyry copper deposits within the State of Alaska. Prospecting for porphyry copper-type deposits in Alaska germinated during the 1940's, grew slowly during the '50's, boomed during the '60's, and matured in the '70's. Although large expenditures have been made in the search for porphyry-type deposits, most accrued data lies dormant in company files. However, an adequate base exists in the literature for a general synthesis of areas that contain porphyry prospects. To simplify the summary, porphyry molybdenum deposits as defined by Clark (1972) are omitted. Description of deposits in their geologic setting permits some correlations between deposit characteristics and crustal environment. These correlations allow speculation about the genesis of the deposits. The summary also attempts to group deposits on the basis of general mineralogic characteristics because diorite model deposits are separated from quartz phenocryst-bearing hosts. Data presented in this chapter summarize observations by the author, published descriptions of specific areas and deposits as noted in the bibliography, and comments by various government geologists. E. M. MacKevett, Jr., D. H. Richter, and H. C. Berg of the US Geological Survey have been particularly helpful. Because few comprehensive descriptions of individual porphyry copper deposits exist for this area, much of the data presented is new to the literature. Details of structure, isotopic geochemistry, and petro- genesis for individual deposits are largely lacking and even the general geology of some belts is not well understood. Details on petrography of Alaskan porphyry copper occurrences are inadequate for construction of ternary diagrams (e.g., Figs. 36a, b, pp. 103, 104, for the northern Cordilleran orogen). Petrographic descriptions summarized in the text are largely from published descriptions whose sources are cited. Porphyry copper-type deposits in Alaska include deposits with pervasive pyrite that contain disseminated copper (but not necessarily coproduct molybdenum). Available data preclude differentiating the deposits by size. No Alaskan porphyry copper deposit is now in production but this is believed to be, in part, a function of economics. In some cases available geologic information is in- adequate for classifying deposits. Some de- posits included with porphyry copper may, with further exploration, be demonstrated to be some other genetic type. Alaska has three distinct porphyry copper provinces: the Hogatza plutonic belt, the Continental Margin belt, and the Interior belt. Each belt contains deposits with characteristic geologic features distinct from those of other belts. Fig. 24 shows the continental margin belt to extend inland from

Jan 1, 1978

By Charles C. Peterson, Ronald E. Enstrom

Significant improvements have been made in the ursine systern for epitaxial vapor gvowtlz of Gds. The electron concentration has been reduced to below 1015 cm-3 with electron-mobility values as high as 7200 sq on per v-sec at 30PK and 60,000 sq cw7 per v-sec at 77°K. These high-purity layers have been successfully gvown on n&apos; layers with thicknesses as snzall as 1 p and as large as 125 p. Furthermore, high-purity layers have been incorporated into an structure without degradation of electrical properties. Different impurity gradients at the n&apos; to n interface were achieved. Using these structures, Gunn oscillators have been operated at frequencies as low as 0.4 GHz and as high as 40 GHz, which equals the highest valzle yet reported. The frequencies nleasured are in reasonable apeenlent with those calculated fron7 the n-layer widths and the transit times. CW operatiolz has been achieved from 3 to 20 GHz. In Gunn devices for >40 GHz operation (i.e., witk an n-layer tkickness below 2.5p), the n layer has been generally too pure to permit oscillations to occuv. ThE mechanism of the Gunn oscillator&apos; is now generally understood.2-5 Electron transfer from the (000) minimum to the ( 100) minima leads to a voltage-controlled negative resistance, which results in the formation of domains of high and low electric fields which travel through the crystal with a characteristic velocity of about 107 cm per sec. When a constant voltage is applied to the sample, this domain motion generaliy leads to oscillations at the transit time frequency, fT = 107/L, where L is the thickness of the active n layer.&apos; In this case, a single high-field domain is nucleated at the cathode and grows until it reaches the anode, where it is absorbed; a new domain then forms at the cathode.5 There are related modes of oscillation of the same device in which a tuned circuit causes a periodic variation of the voltage across the device. The frequency then may be either above or below fT. It has been shown that oscillations will occur when n • L 2 1012 cm"2, where n is the carrier concentration in the active region. At lower doping densities, 10" 5 n . L 5 lo&apos;&apos;, the doping is said to be subcritical for oscillation and the description of the device operation changes since the domains become comparable in thickness to the device thickness, L. Nevertheless, such devices have been found to be "active" and, in fact, are useful as amplifiers.778 For CW operation, one wishes to minimize the power dissipation, which is related to the electric field, E, and the low-field resistivity, p. Below threshold, the power dissipation density is approximately Typically, at threshold where E -- 3 x 103 v per cm, the dissipation density is 107/p watts per cu cm, p in ohm-cm. Furthermore, it is desirable to provide good conduction of the heat generated in the active region. The temperature rise, AT, across the active layer of a sandwich structure, with a heat sink on one side, is given by AT = (E&apos;/P)(L~/~~) where it is assumed that the thermal conductivity, u, and resistivity, p, of GaAs do not vary appreciably over the range of temperature and electric fields existing in the layer. This expression shows that, subject to maintaining an appropriate (n . L) product, CW operation is favored by a higher resistivity, a lower threshold field, and a thinner device. The above device requirements place some severe restrictions on the materials to be used, especially for high-frequency (>10 GHz) operation. Here, it is necessary to prepare very thin (<10 µ) layers of GaAs, in a state of high purity (-1 ohm-cm), complete with very low-resistance ohmic contacts. Problems of handling such thin and fragile samples become inereasingly severe as the frequency is raised. Furthermore, while good low-resistance ohmic contacts are easily applied to low-resistivity GaAs, contacting difficulties are encountered for these higher-resistivity materials.

Jan 1, 1968

By D. W. Fuerstenau, D. A. Sullevan

In the experimental work for this comparison of wet and dry grinding, it was found that the size distributions for wet grinding operations are characterized by a constant value of the distribution modulus, (a; whereas, for dry grinding the distribution modulus decreases slightly with increased size reduction. Wet grindability seems independent of the weight of material in the mill while dry grindability depends on weight. Experimental data and eqmtions for each process are presented for noncleavable isotropic material, for cleavable or material in which there is some form of internal stress, and for energy consumption. The equation ED/EW=BK-? (where ED and Ew are, respectively, energy for wet and dry grinding, k is the size modulus, and B and ? are constants) was found to give the ratio of energy. Dry grinding is generally considered to require more energy than wet grinding. Taggart&apos; states that power consumption in wet grinding ranges from 60 to 90 pct of that required for dry grinding. Bond&apos; states that dry grinding requires one third more power than wet grinding. It is interesting that Rose and Sullivan&apos; note this same difference in power required for wet and dry grinding, but they state that on purely mechanical grounds it is difficult to see any great difference in fundamental principles between wet and dry milling, since dry milling may be regarded as wet milling with a fluid of low viscosity (i.e., air vs water). Yet it must be the viscosity of the fluid that is responsible for the differences between wet and dry grinding. Probably the most comprehensive investigation comparing wet and dry grinding has been that made by Coghill and Devaney. They compared the grind-ability of both chert and dolomite in a 19x36-in. batch ball mill under both wet and dry conditions. In these tests the weight of ore in the mill was varied from 35 to 200 lb and each grinding test was carried out for such period of time that the amount of -200-mesh material in the product was essentially the same for each test with a given material. Cog-hill and DeVaney&apos;s data for the grindability of dolomite, which are reproduced in Fig. 1, show that a comparison between wet and dry grinding is com- plex. The comminution of a material by a wet grinding method is characterized by a constant grindability over a wide range of mill loadings. Since grindability is the weight of material comminuted per unit of energy expended, it is equivalent to (w)/ (p)(t), where W is the weight of material being ground, P is the power, and t is the grinding time. In the case of wet grinding, the grindability of dolomite in the Coghill and DeVaney experiments was 0.546 * 0.009 ton per hp-hr when the load of dolomite in the mill ranged from 50 to 200 lb. On the other hand, for dry grinding no such simple relationship was found to exist between power, time, and weight of material in the mill. Dry grinding efficiency appears to depend greatly upon the amount of material within the mill. When the mill contained

Jan 1, 1961

By AIME AIME

CHARLIE WARNER, Chairman of the Petroleum Division, is no stranger to the problems of the oil industry or to those of the Petroleum Division, after more than 25 years of experience in locating and producing oil and more than 22 years of membership in the Institute. He was born at Jefferson, N. Y.. April 27, 1894, and educated in the public schools of New York State and at Cornell University where he studied geology and allied sciences from 1913 to 1917 and received a B.A. degree. Immediately upon completion of this training, he was employed by the Empire Gas & Fuel Co. as a field geologist in Oklahoma and Kansas. Two years later he became district geologist for the Emerald Oil Co. in Oklahoma and Kansas, and in 1920 he rejoined the Empire Gas & Fuel Co. in the capacity of district geologist in Oklahoma. In September of 1921 he began his association with the Houston Oil Co. of Texas. He was district manager for the company in the Mid-Continent area until 1932 when he was transferred to the head office at Houston, where he became superintendent of the land and lease department in 1934 and was elected a director of the company in 1941. In these capacities, and also as petroleum engineer for the company, he keeps in intimate touch with all phases of field activity and with the regulation of the industry by State and Federal agencies.

Jan 1, 1943

By Joseph C. Mead, Alan Stanley

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941,when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948. The magnetite concentrate produced in the milling operation was too fine (minus 20 mesh) to be used directly in iron blast furnace operation, and most of the magnetite had to be stockpiled in 1942 and 1943. In 1943, the Defense Plant Corp. built a Greenawalt sintering plant at Tahawus, N. Y., to put the magnetite concentrate in a more suitable form for use in the iron blast furnace. The Greenawalt sintering plant consists of three 10 by 25 ft sintering pans designed to produce 1800 gross tons of sinter per 24 hr. The vacuum to each pan is produced by two Greenawalt fans in series, pulling approximately 30,000 cu ft of air per minute at 50 in. water gauge vacuum. The plant started operation in August 1944. The present plant production averages 25 tons per operating pan hour (approximately 224 lb per operating hour per square foot of grate area) of plus 1 in. sinter. Raw feed to the plant consists of 61 pct magnetite, 4 pct anthracite coal culm, and 35 pct minus 1 in. return fines which are conveyed to a pug mill where the materials are mixed thoroughly and water added to give the mixture 5.5 to 6 pct moisture. The mixed prepared feed is conveyed to two 4 by 10 ft vibrating screens where the minus 1 in. plus 5/8 in. return fines are screened out and discharged into a surge bin for use as a hearth layer. The minus 5/8 in. prepared feed is discharged into another surge bin for use as prepared feed. A charge car, electrically operated, having a capacity of one charge of prepared feed and several charges of hearth layer, lays a thin layer of plus 5/8 in. return fines and 9½ in. depth of prepared feed into the pans. A fluffing roll and a vibrator on the car fluffs and spreads the prepared feed into the pans. An ignition car, electrically operated, ignites the top of the bed with a 30 sec flash burn. The 9½ in. bed sin-ters in approximately 13 min. Dumping the pan, and recharging and igniting the bed requires 2 min. To improve the quality of the ilmenite concentrate produced in the mill and to reduce the amount of titanium dioxide lost in the mill tailings and in the magnetite product, extensive research work and pilot plant operations have been done on grinding the crude ore to minus 65 mesh size (rather than to minus 20 mesh) and concentrating it by a combination of magnetic separation (for magnetite recovery) and flotation (for ilmenite re-covery). These tests have proved successful in increasing ilmenite re-covery and grade. With the development of the ilmenite flotation process to a stage where a full scale flotation plant was in the design stage, the problem arose of handling the 65 mesh magnetite concentrate that would be produced. In order to study and solve the problems of handling and sintering the 65 mesh magnetite in the sinter plant, a pilot sinter plant was secured from John E. Greenawalt. The effect of using 65 mesh magnetite in the sintering operations was then studied on the 2.4 sq ft test pan, operating under conditions as similar to the large plant as could be set up in the laboratory. A series of tests were run in the test pan on present sinter plant feed that had been mixed in the plant pug mill. An average production and an average quality of sinter produced in this series

Jan 1, 1950

By A. N. Winsor

Increased use of private aircraft in civil engineering, mining, forestry, and other land-use activities creates an opportunity for amateur aerial photography. Taking a photograph having less than 5° tilt requires precision equipment and skilled personnel, while controlled horizontal photography is primarily a terrestrial method that has passed to the limbo of forgotten things. But the remaining possibility – oblique aerial photography – can be…

Jan 2, 1955

By C. C. Bailey

THE vendor seeking outside capital for his project has the following potential sources which may be approached; 1--private sources, 2-institutional funds, 3--government agencies, 4--established mining concerns, and 5-public financing.

Jan 7, 1953

By S. J. Hruska

Rate expressions for the formation of two-and three-dimensional nuclei on foreign substrates are developed, taking into account previously neglected contributions to the standard Gibbs free energy of formation of critical nuclei. The temperature dependence of critical super saturation data predicted using these expressions is in accord with data for cadmium on copper and sodium on CsCl. EXPERIMENTAL data on the heterogeneous nuclea-tion of metal crystals from the vapor phase1&apos;2 exhibit the temperature dependence predicted by a nucleation rate equation derived by Pound et al.3 In their treatment, the critical nuclei are visualized according to the Volmer4 model as cap-shaped (three-dimensional). Accordingly, it seems desirable to compare these data with a nucleation rate equation which is derived on the assumption of disk-shaped (two dimensional) nuclei. Further, Lothe and Pound5 have recently shown that the standard Gibbs free energy of formation of these critical nuclei contains a contribution which has heretofore been neglected. Thus it is necessary to re-examine these nucleation data using a rate equation which contains this contribution. The van&apos;t Hoff isotherm relates n(i), the concentration of nuclei of critical size i (i = number of atoms), to nil), the concentration of adsorbed single atoms: where standard Gibbs free energy of formation of critical nuclei given by is temperature insensitive and is the bulk free energy change/volume of transformed material], T = substrate temperature and k = Boltzmann&apos;s constant. Previously,3 was determined by considering only the contributions of bulk and surface free energies in transforming i atoms from the population nil) to a cluster of i atoms. It has been shown5 that this procedure does not take into account the free energy contribution arising from the multiplicity of sites, q, where the clusters can be situated. If this contribution, -kT In q/n(l),is added to iG3 [Note that this increases n(i) by a factor q/n(l).] Since the above does not affect the remaining terms in the rate expression of Pound et al., the details are referred to their paper. The resulting nucleation rate is If the experimental AGV and T values at some common value of are employed, a plot of vs T(ln C3/l + In p&apos;) should yield a straight line of slope k/B<p and intercept . The corresponding plots for / = 1 nucleus per sq cm sec and C3 = 1018 are shown in Figs. 1 and 2 for cadmium on copper1 and sodium on CsCl2 and the values of obtained therefrom are entered in Table I. It is apparent that the data yield reasonable straight lines with about the same scatter as found using the equation of Pound et al. When the configuration of minimum free energy for a nucleus is a circular monatomic layer, the standard free energy of formation is

Jan 1, 1963

By E. F. Steeb, P. C. Rosenthal

BlANKS 8 in. long were cut from the as-received bar stock and austenitized at 1560° F for 1 hr, oil quenched, tempered at 1140°F for 1 hr, and water quenched. The heat-treated blanks were machined into tensile specimens which were subsequently used for the straining operation. Some of the tensile specimens were temper embrittled at 900°F for 24 hr and air cooled prior to or following the straining operation. The specimens were strained in tension up to 5 pct total strain (elastic plus plastic) either at room temperature or at 900°F. The reduced sec- tion of the tensile specimen employed was 5 in. long and 0.600 in. in diam. This size specimen was sufficiently large to permit two standard Charpy impact bars to be machined from it. One group of specimens was temper embrittled at 900°F for 24 hr under stress of about 20,000 psi applied with a hydraulic tensile testing machine. Approximately 0.34 pct plastic strain occurred during this treatment. A comparison of series "A" and "B" data in Table I at 0 pct strain, reveals that the steel was rather highly susceptible to temper embrittlement, the embrittling treatment causing the transition temperature to rise 165°F. The 28 ft-lb level, which was near the center of the sharp-rising portion of the transition curve, was selected as the

Jan 1, 1959

By N. J. Grant, D. S. Bloom

N recent reports, Sully&apos; and Beck and coworkers&apos; I have advanced hypotheses concerning the formation of the phase. Both of these hypotheses are based on Pauling&apos;s theories of the electronic configuration of the elements of the first transition group. Sully considered that the number of electrons which can be absorbed in filling electron "holes" is the factor which determines whether or not the structure can form. Beck suggested that the presence of a certain concentration of electron "holes" is the controlling value. It can be shown that a similar criterion can be developed without making reference to Pauling&apos;s theories. Table I shows the elements of the first transition group and the incidence of the a structure in the binary systems of these elements according to the data presently available. Also appended is the number of electrons considered to exist in the 3d-4s levels of these elements. If the atomic percentages for the phase are listed as shown in Table 11, and if the number of electrons in the 3d-4s levels per atom is calculated for the a boundary values, the results are as shown in the last column. It can be seen that the numerical values are all in the vicinity of 7 electrons per atom. This is true also for the ternary Cr-Mo-Ni IT phase, which occurs in a system in which none of the binary compositions are known to develop the phase. In the Fe-Mo binary, the high temperature a phase, which occurs at a composition of 50 atomic pct of each element, also yields a ,;1 e of 7 electrons per atom. From inspection of Tables I and 11, it develops that any series of sequential numbers which is assigned to the elements under consideration will result in the numbers pertaining to a compositions grouping themselves around one specific number. It does not follow, however, that this random number necessarily has physical significance. Such a point has already been discussed by Hume-Rothery." One interesting point develops from this study, however, and that is the position of manganese with reference to the other elements and to the phase. In the system used here, the formation of phase is associated approximately with the value of 7 electrons per atom, which is also the number of electrons per atom that manganese has. Manganese, it will be recalled, exists in three different crystal forms, none of which are the usual, simpler metallic forms; on the other hand, elements just to the left of manganese (in Table I) generally have lower coordination-number structures (body-centered cubic) than do elements to the right of manganese (face-centered cubic). The contribution to a complex crystal structure by the interalloying of elements from opposite sides of manganese is significant in that the a phase is formed in binary systems including one element from each side of manganese, with manganese capable of participating with both sides. It is indeed an interesting coincidence that manganese, with 7 electrons per atom, solidifies in complex crystal forms, and that when alloys of the transition elements are made which have seven 3d-4s electrons per atom, they, too, tend to assume a complex crystal form. From the above, it might be deduced that the study of the a phase might be advanced by a critical examination of the element manganese and how its structure is affected by small additions of elements which change the 3d-4s electrons per atom number. The role of atom size would also be of interest in formation. References &apos; A. H. Sully: The Sigma Phase in Binary Alloys of the Transition Elements. Journal Inst. Metals (1951) 80, Part 4, p. 173. 2 S. Rideout, W. D. Manly, E. L. Kamen, B. S. Lement, and P. A. Beck: Intermediate Phases in Ternary Alloy Systems of Transition Elements. Trans. AIME (1951) 191, p. 872; Journal of Metals (October 1951). "W. Hume-Rothery, H. M. Irving, and R. J. P. Williams: The Valencies of the Transition Elements in the Metallic State. Proc. Royal Soc. (September 1951) 208A. p. 431.

Jan 1, 1954

In the General Alphabetical and Analytical Index of A I M E Publications for the years 1926 through 1935, a complete list of the volumes covered is printed on page 5, but the dates of publication of the volumes are not given Therefore the following information regarding the volumes that were printed without numbers may be useful to users of the Index

Jan 1, 1937

By George Krauss, Morris Cohen

NUMEROUS investigators1-4 have shown that one of the most conspicuous effects of the reverse marten-sitic transformation in Fe-Ni alloys is the stabilization of the austenite which forms on reversal. However, the present authors5 found a virtual absence of stabilization in a recent study of this subject. The purpose of this note is to account for the discrepancy.

Jan 1, 1963

By H. W. Schadler

The superplastic behavior of low carbon and manganese bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests are reported which indicate that high strain rate sensitivity (>0.5) and adequate elongations are achievable in ultrafine-grained steels 1 to 2 p, but at strain rates which are not commercially attractive. It has been demonstrated that the fine grain size is retained after long times and high strains if the temperature is kept within the range of the two-phase (a + ?) field. INTEREST in superplasticity has been stimulated by the desire to: 1) understand the origin of, and mechanisms responsible for, the large uniform elongations observed, and 2) exploit this property for commercial advantage in metal forming operations. Although the Zn-22 wt pct Al alloy presently being studied as a model material1-5 may find application in sheet forming and extrusion, the potential of super-plasticity should best be realized in large tonnage materials, such as steel and aluminum alloys. The degree of superplasticity in low-carbon and manganese-bearing steels has been evaluated. The results of elevated-temperature stress-strain rate and elongation tests on ultrafine grain size material are reported. Avery and Backofen6 and Hart7 have shown that geometrically stable flow leading to extensive uniform elongation in the tension test is associated with high values of the strain rate sensitivity, m, defined: Lozinsky had reported that titanium and zirconium experience permanent deformation if subjected to a constant load and cyclic heating through the temperature range of the phase transformation. Although strain rate sensitivities in excess of about 0.2 had not been reported previously for steel, permanent deformation had been observed11-13 in a wide variety of steels subjected to a constant load and cyclic heating through the temperature range of the a-? phase transformation. Thus by analogy, steel could be expected to exhibit high strain rate sensitivity but only in the a + ? condition. High strain rate sensitivity has been observed at 650°C (a + Fe3C), but not reported as such, by Bailey, Dickenson, and pearson14 in 1931 at a strain rate of about 10-9 per min. It then remained to determine whether high tensile elongations would be observed in a rate-controlled test at constant temperature and at what strain rate strain rate sensitivity values greater than 0.5 would be observed. Since previous experience8 had indicated the importance of fine grain size to realizing high m at reasonable strain rates, it was first necessary to produce an ultrafine grain size and then keep the grains from growing during the test. The results of this investigation show that fine grain size can be readily produced16 and maintained by restricting the temperature of testing to below the ? transus. Further, superplasticity (high m and large uniform elongation) is observed. However, the strain rate range is only marginally useful for commercial forming operations with the finest grain size produced. MATERIAL The material investigated initially was a 1.9 wt pct Mn, 0.42 wt pct C, hot-rolled bar previously used by Low and Turka1015 and available in the laboratory. The 0.500-in. round was cold-rolled to a 0.090-in. flat, annealed for 4 hr at 850°C in argon, air-cooled, and cold-finished to 0.050 in. Subsequently, four additional steels of the compositions given in Table I were investigated to explore the effects of manganese, carbon, and test temperature on the observed stress-strain rate behavior. These steels were melted under argon, cast to 0.75 by 2 by 5 in. slabs, hot-rolled at 850°C, surface-finished to 0.13 in., and cold-finished to 0.050 in. Sheet tensile specimens 0.200 in. x thickness with 1- or 2-in. gage length were cut parallel to the rolling direction. Table I also includes the nominal transformation temperatures for the AISI 1340 and the four experimental steels. EXPERIMENTAL PROCEDURE Production of Fine Grain Size. Ultrafine grain size (1 to 5 p) was considered essential for this studv. Grange16 has described two techniques for producing

Jan 1, 1969

By B. E. Sundquist

The various methods based on solution models for obtaining free energies of mixing from miscibility-gap data have been applied to a number of binary-alloy systems. For nine of these systems there exist experimental thermodynamic data that permit a comparison of the results to experiment. It was found that the method of van der Toorn and Tiedema almost invariably leads to results that are physically unacceptable and that vary drastically with small changes in the miscibility-gap parameters. The subregular solution model is found in all cases, except the Al-Zn, Fe-Cr, and Cu-Pb systems, to exaggerate the free energy of mixing by 30 pct or more. The model developed by Lumsden is found to give results that are often in excellent agreement with experiment and which exaggerate the free energy of mixing by no more than 30 pct. These results and others give evidence that the Lumsden treatment of the effect of unequal atomic sizes and of imperfect configurational randomness due to deviations of AB bond energies from the mean of AA and BB bond energies is adequate for most systems. ANALYTIC expressions are frequently proposed for the dependence on composition of the activities of the components of a solution. Because the development of solution theory is incomplete, these expressions contain parameters which must be determined by experiment. The measurement of activities is often difficult and consequently such measurements are less readily available than are measurements of phase equilibria which, under certain conditions, can also be used to evaluate these parameters. For example, suppose it is known that two structurally dissimilar phases, each of known composition, in an n-com-ponent system are at equilibrium at a given temperature and pressure. n equations can be set up in terms of these parameters expressing the equality of the chemical potential of each component in the two phases. In addition, one can write the Gibbs-Duhem equation for each phase that also contains these parameters. Thus, if these n + 2 equations contain n + 2 parameters, these parameters can be determined (at the temperature in question) from the phase diagram alone. If the average number of parameters in each expression for the activity of a given component in a given phase is V then there will be 2nV parameters involved. Equating 2nV to n + 2 shows that, for n + 2, V = 1. If the temperature dependence of each parameter were to be expressed in some explicit form one could use equilibrium conditions at a number of temperatures to increase V. The situation is much improved when the two phases in equilibrium are structurally similar. It can then be assumed that, stably or metastably, two phases will become one at higher temperatures. Thus the number of parameters involved becomes nV instead of 2nV. Hence, V = 2 for n = 2 using only one temperature. (It is implied here that the activity expressions used are valid over the entire composition range.) In this investigation only the equilibrium of two structurally similar, two-component phases (miscibility-gap systems) will be considered. The various proposed solution models will be applied to a number of these systems and the results compared with available experimental results. All of the analytic expressions that have been proposed for the free energy of mixing of a two-component system are of the form where ?Gmix is the free energy of mixing per mole of solution, N1 and N2 are the mole fractions of components 1 and 2, respectively, and f(Ni, T) is some function of composition and temperature. In the "ideal" solution model f = 0. In the "regular" solution model f = a constant. Since these two models permit only a symmetric equilibrium diagram they will not be considered further here. The simplest model that permits a nonsymmetric miscibility envelope is the so-called "subregular" solution model proposed by Hardy.1 This model gives where the Ci(T) are functions of temperature only. The same expression for f is obtained from the "linear a function" model proposed by Darken and Gurry2 and applied to miscibility-gap systems by Wriedt.3 This model requires that the a function defined by be a linear function of composition (yi is the activity coefficient of component i). This model is not purely hypothetical for it has been found2 to hold true for a number of systems. It is readily shown3 that the f(Nl, T) obtained from this model is of the form given in Eq. [2]. It will be noted that the subregular solution model contains only two parameters and hence both of them can be determined at any desired temperature below the critical temperature, Tc, for a miscibility-gap systems in the manner described previously. At T, the two constants can be determined by equating the second and third derivatives of ?Cmix with composition to zero. Another two-parameter model was proposed by Lumsden4 who set

Jan 1, 1967

By AIME AIME

TWO papers, "Calcium, Strontium, and Barium Metals," by Charles Hardy and Paul M. Tyler, and "The Mining of Gems and Ornamental Stones by American Indians," by Sydney H. Ball, were presented before the Rare Minerals and Metals group at its session Tuesday afternoon in the Auditorium. Donald M. Liddell, chairman, presided. Mr. Tyler summarized the first paper, outlining the uses, history, occurrence, manufacture, production and trade, markets and prices of the three metals. In discussion, in response to the chairman&apos;s query on "what are they doing in Russia with calcium, strontium, and barium," Guy C. Riddell replied that nothing is being done on a production basis. The great rare metals plant in Moscow is active, however, on other elements. "They are making radium chloride, uranium oxide, vanadium, cadmium, tungsten, molybdenum, selenium, antimony compounds; and mercury, nickel and arsenic are under production at interior plants. The rare metals plant is busily conducting research on beryllium, rhenium, lithium, bismuth, strontium and zirconium. These are the main rare metal activities. Much hard-alloy work. for cutting and facing, is under way:

Jan 1, 1933

By AIME AIME

THAT neither the Reconstruction Finance Corp. nor its subsidiary, the Metals Reserve Corp., are in competition with private enterprise was stressed by Charles B. Henderson in an informal talk before the N. Y. Section, A.I.M.E., on Sept. 23. Among other things, the speaker stated that the R.F.C., since its establishment, had authorized loans of $12,000,000, of which over $8,775,000 has actually been distributed. Of this amount, over $6,600,000 has been repaid. None of this money was appropriated by Congress, the sole assistance from that body being the initial authorization of $500,000,000 capital stock.

Jan 1, 1941

By Charles White Merrill

Mankind&apos;s progress is measured in minerals. Man&apos;s emergence from prehistory is marked by passage through a Stone Age and a Bronze Age and into the present era, sometimes called the Iron Age or the Age of Metals. With the evolution of civilization and the development of a modem industrial economy, minerals become more and more important. Structures, roads, and machines are built largely of minerals; the energy to heat the structures and to drive the machines is mostly mineral; agricultural fertility is maintained by mineral fertilizers and water; and military strength is provided by fortresses, armaments, and munitions, largely of mineral origin. Thus in the material world, in the productivity of the economy, access to minerals has paramount importance. Every evidence indicates increasing dependence on minerals in the modem economy, particularly on the mineral fuels as energy sources to provide the power base for advancing industrialization. Both the total and the per capita consumption of almost every mineral is increasing in the industrialized nations. Moreover, nations with predominantly agrarian economies call themselves underdeveloped and universally strive to industrialize. Most mineral consumption trends in the more advanced economies have been greatly exceeding population growth-which itself has been advancing at an accelerating rate-and sometimes have surpassed the growth in real income. Some minerals have only recently been adopted or grown to importance in use. Titanium metal did not appear as a commercial product until 1948, and even coal seriously displaced wood as a source of heat less than two centuries ago. On the other hand, minerals have always played an important role in construction. The prehistoric megaliths that form the dolmens of Salisbury Plain are stone; the pyramids are andesite faced with limestone; and many other ancient structures are built of mineral materials. In modem times the whole course of architecture has been redirected by new building materials, mostly mineral. Most conspicuous is the sky-

Jan 1, 1964

By Edward Steidle

THAT veterans are crowding the colleges is no longer news; 78 per cent of the 1916-47 enrollment in mineral industries curricula in the United States were veterans, but the rapid comeback from an estimated 1262 total mineral industries students in 1944-45 to 11,422 in 1946-47 is almost astonishing. The figure, which includes 1008 graduate students, is a substantial increase over the previous top record of 9619 in 1938-39. A small part of the increase is caused by the larger number of women entering the field, of whom there were c 9 in 1916-47. Petroleum leads the curricula with 34.5 % of the enrollment, metallurgy is second with 28%, and mining is third with 18%. Table 1. shows all curricula offered and those accredited by ECPD. Using the Mississippi River as a dividing line, 31 colleges in the East and 27 in the West offer curricula in the mineral industries.

Jan 1, 1948